Repair Of Sub Area Office Of Aocm Sub Area Of Sohagpur Area. Repair Of Sub Area Office Of Aocm Sub Area Of Sohagpur Area.
Tender Value
4.15 Lakhs
Estimated cost
Bid Submission
09 Aug 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sohagpur Area → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair Of Sub Area Office Of Aocm Sub Area Of Sohagpur Area. Repair Of Sub Area Office Of Aocm Sub Area Of Sohagpur Area.
BOQ
| Sl. No. | Item Description |
| 1 | Item Description/ Heading |
| 2 | DISMANTLING AND DEMOLISHING Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 metres lead : Thickness above 40 mm up to 75 mm |
| 3 | DISMANTLING AND Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 4 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 5 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 6 | Providing and applying plaster of paris putty of 2 mm thickness overplastered surface to prepare the surface even and smooth complete. |
| 7 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 8 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness |
| 9 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 500x500 mm |
| 10 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge |
| 11 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 12 | Providing and fixing medium density PVC board exterior grade mocked to frame backing or studding with screw etc. comp (frames backing or studding to be paid sparely 10mm PVC Board |
| 13 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade : Two or more coats on new work |
| 14 | Point wiring in conceded with PVC insulated cable with copper conductor 1.5 sq.mm Light point (medium) |
| 15 | Point wiring in conceded with PVC insulated cable with copper conductor 1.5 sq.mm Fen point |
| 16 | Point wiring in concededwith PVC insulated cable with copper conductor 1.5 sq.mm 3 pin 5 Amp (some board) |
| 17 | Point wiring in conceded with PVC insulated wide copper conductor 6 sq.mm |
| 18 | Supply and fixing of ISI mocked of accepted started of MCB 6. To 32 AMP |
| 19 | Rewiring of Ex. fen motor against old copper 12\" Ex. Fen |
| 20 | Supplying fixing and test of approvedtube fluorescent fittingceiling Installation 1x 40w. |
| 21 | Total impact of GST for the purpose of CTC |
AI Tender Summary
Tender Timeline
Jul 26, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedAug 09, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 11, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender