|
| 1 | Demolition of brickwork or stone boulder masonarybuilt in cement mortar including all quoins, arches, pillars etc complete all as specified. |
| 2 | Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified. |
| 3 | Brickwork with sub class ‘B’ (except bricks) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified. |
| 4 | Brick work with sub class \"B\" bricks straight or curved on plan exc 6 mtr mean in radius built in CM 1:4 |
| 5 | Brick work with sub class \"B\" (except bricks) bricks straight or curved on plan exc 6 mtr mean in radius built in CM 1:4 |
| 6 | Taking down cement plaster of any description including raking outjoints, hacking for key, scrubbing down with water etcall as specified. |
| 7 | Rendering 15 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces with using integral waterproofing compound including finishing the surface even and smooth without using extra cement complete all as specified. (supply only of W P C shall be measured and paid separately). |
| 8 | Rendering 10 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and as directed |
| 9 | Rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 10 | Supply only integral water proofing compound. |
| 11 | Preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified. |
| 12 | Preparation of newly plastered surfaces of ceiling and applying two coats of white washcomplete all as specified. |
| 13 | Preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion complete all as specified. |
| 14 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified. |
| 15 | 50mm thick PCC (1:3:6) type C-2 using 20mm graded stone aggregate as in plinth protection and similar works including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified. |
| 16 | Chequered cement concrete tiles 20 cm x 20 cm x 20-22mm thick with grey cement and no pigment machine pressed, set, jointed and pointed in neat cement slurry in floors over and including 20 mm thick screed bed in cement and sand mortar 1:6 complete all as specified. |
| 17 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified. |
| 18 | Non skid coloured joint free ceramic tiles 400x400x 6-7mm thick in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade oftiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified. |
| 19 | Glazed ceramic tile 300 x 200 x 6-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4 complete all as specified. |
| 20 | 20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 20mm thick screed bed in cement and sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 21 | 20-25 mm thick machine cut kota stone slab as in skirting/dado etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick plaster in cement and sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. (Length of Kota Stone slab shall be to match the size of stone slab in flooring and the width as directed by Enginer-in-Charge) |
| 22 | 20 mm thick makrana white marble, machine cut, bedded and jointed with and including 20mm thick screed bed in cement and sand mortar 1:6 including cutting and polishing complete all as specified. |
| 23 | Dismantling wrought iron or mild steel work of anydescription not other wise provided for. |
| 24 | Dismantling of plain &corrugated steel sheeting any gauge, thickness including Nanital or similar pattern roof covering like ridges, hips, valleys and flashings etc complete all as specified. |
| 25 | Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or incl butt welded tubes conforming to IS 1161-1998 grade St-240 and painted one shop coat of zinc chromate promer paint (incl preparation of surface) at contractor\"s workshop before fabrication complete all as specifed and directed. |
| 26 | Mild steel rolled section as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc. confirming to gradeFe-290. Gde- E-165. complete all as specifed and directed. |
| 27 | S&F Galvanised 2 stand, steel barbed wire 2.24 mm dia barbed with 2mm barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provison of galvanised mild steel wire staples or steel pins etc .complete all as specifed and directed. (Each line wire to be measured) |
| 28 | S&F pre-painted galvalum aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified. |
| 29 | S&F pre-painted galvalum aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering/cladding to wall, fixed with self tapping screws as a specified. |
| 30 | Dismantling of wall and ceiling board (fibre, pulp insulation etc) for insulation board/slab/blankets any thickness incl cover fillet. |
| 31 | Aluminium anodised snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching.The snap grid shall consist of aluminium anodised main and cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/Rm and 23.5 x 26.4 x 1.4 mm weighing 0.191 Kg/Rm respectively.The main and cross tee shall be jointed at junction crossing with aluminium anodized angle bracket of size 15 x 15 x1.5 mm weighing 0.12 Kg/Rm fixed with suitable MS bolts, nuts and washers.The snap grid (main/cross tee section) shall be supported at ends all along the wall with aluminium anodized angle of size 40 x 25 x 2 mm weighing 0.36 Kg/Rm fixed to wall with suitable arrangement and providing 4 mm thick AC plain building board in grid ad applying three coats of white wash including preparation of surfaces. |
| 32 | Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc fixed in repairs, complete all as specified. |
| 33 | Vitreous China wash down water closet pan “Pedestal pattern” size 580x440mm white (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc fixed in repairs, complete all as specified. |
| 34 | PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed in repairs, complete all as specified. |
| 35 | Flush pipe of polyethylene of low or high density, 32 mm dia for low level cistern including taking down old pipe, complete all as specified. |
| 36 | Vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe fixed in repairs (excluding flushing cistern, flush pipe and waste pipe) all as specified. |
| 37 | Vitreous china wash basin, white, flat back, size 630x450mm including pillar tap, waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc., fixed in repairs complete all as specified. |
| 38 | Sink made of stainless steel1.00 mm thick sheet for kitchen or Laboratory with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm with bowl size 410 mm x 330mm x 160mm supplied and fixed in repairs complete all as specified. |
| 39 | Sink with drainage board made out of stainless steel1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm supplied and fixed in repairs complete all as specified. |
| 40 | 600mm x 450mm beveled edge mirror of selected quality glass, mounted on 6mm thick commercial quality ply-wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete supplied and fixed in repairs, all as specified. |
| 41 | Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified. |
| 42 | PVC connection 15 mm size, of length 600 mm, with PTMT nuts supplied and fixed in repairs complete all as specified. |
| 43 | 32 mm bore waste fittings, brass, chromium plated for glazed ware sinks, basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified. |
| 44 | S&F grating round 140mm size of PTMT fixed with cement motar.(Min weight 50 gms) |
| 45 | S&F grating round 125mm size of PTMT fixed with cement motar.(Min weight 40 gms) |
| 46 | Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc including cleaning for refixing or removal complete all as specified. |
| 47 | Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc including cleaning for refixing or removal complete all as specified. |
| 48 | 15mm bore tubes, medium grade, galvanised with and including all fittings fixedto walls, floors, or ceiling or laid in floors etc complete all as specified. |
| 49 | 20mm bore tubes, medium grade, galvanised with and including all fittings fixedto walls, floors, or ceiling or laid in floors etc complete all as specified. |
| 50 | Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed. |
| 51 | Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed. |
| 52 | Angle stop valve of 15mm size PTMTanycolour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) |
| 53 | Stop valves cast copper alloy but fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified and as directed. |
| 54 | Stop valves cast copper alloy but fancy type chromium plated with long shank and cup (Concealed type) screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified and as directed. |
| 55 | Gate valves, with iron wheel head, screwed both ends for bore of 15 mm pipe andsupply and fixed in repairs. |
| 56 | Swivel shower of PTMT any colour for fixing with 15 mm pipe (minimum weight 40 gm), supplied and fixed in repairs complete all as specified and as directed. |
| 57 | Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete all as specified and as directed. |
| 58 | Pillar taps cast copper alloy, fancy type with capstan head, CP, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe15 mm bore, supplied andfixed in repairs,complete all as specified. |
| 59 | Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe20 mm dia (minimum weight 210 gms) complete all as specified. |
| 60 | Brass, CP mixer for mixing hot and cold water screwed down for 15mm dia iron pipe and fixed in repairs, complete all as specifed. |
| 61 | M&L for dismantling of water tank of capacity exc 500 and not exc. 1000 litres and removing to store and supply and fixing of 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top & FDA approved, tripple layer body, 100% UA stablised, rust proof) hoisted and fixed in position all as specified in SSR Part-I, complete, all as specified and as directed. Note : Water storage tank shall be White with screwed lid |
| 62 | M&L for dismantling of water tank of capacity exc 250 and not exc. 500 litres and removing to store and supply and fixing of 500 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top & FDA approved, tripple layer body, 100% UA stablised, rust proof) hoisted and fixed in position all as specified in SSR Part-I, complete, all as specified and as directed. Note : Water storage tank shall be White and screwed lid |
| 63 | Taking down chowkhats or frameswith shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified. |
| 64 | Taking down chowkhats or frameswith shutters (without taking off shutters from the frames) of size exceeding 1.5 sqm and not exceeding 4.00 sqm each and removing from site complete all as specified. |
| 65 | Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified. |
| 66 | Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified. |
| 67 | Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified. |
| 68 | PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified. |
| 69 | PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etccomplete all as specified. |
| 70 | 35mm thick, 2nd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified. |
| 71 | 35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified. |
| 72 | Painting to new wood or wood basedsurfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified. |
| 73 | Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified. |
| 74 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail.Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined togetherwith solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified and as directed. |
| 75 | Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified. |
| 76 | 250mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections & fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete all as specified. |
| 77 | 200mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified. |
| 78 | 150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified. |
| 79 | Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified. |
| 80 | 300 mm size mild steel ordinary rat tail rod pattern springs including roller and roller plate, ISI marked complete all as specified. |
| 81 | S&F door closer hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width and of weights between80 Kg (aluminium Die cast) Body completed all as specified. |
| 82 | Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified. |
| 83 | S&F in repairs Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified. |
| 84 | Mild steel framed workas in grills, grating etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, conforming to Fe-290. Gde- E-165.complete all as specified. |
| 85 | Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete withglazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed. |
| 86 | Factory made steel windows with side hung shutters including projecting type hinges with steel handle & steel peg stay complete withoutglazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and as directed. |
| 87 | Steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed. |
| 88 | Preparation ofnewsteel surfaces of any descriptionexc 10 cm width or girth, priming with red oxide primer and painting with two coats of synthetic enamel paint complete all as specified and directed. |
| 89 | Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads complete all as specified and as directed. |
| 90 | 03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified. |
| 91 | 03 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified. |
| 92 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in any type of soil all as specified and as directed. |
| 93 | Returning, filling in and including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and as directed by the Engineer-in-Charge. |
| 94 | Removing excavated material to a distance not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all asspecified andas directed. |
| 95 | M&L concrete bed to drain pipeincl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) for 150mm bore pipe all as specified. |
| 96 | M&L for 150 mm Sail-glazed stoneware drain pipes laid in trenches and jointed including Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested all as specified. |
| 97 | S&F PVC collapsible waste pipe800mm longwith complete fitting etc 32 mm dia. Complete all as specified. |
| 98 | M&L for PCC 1:4:8 type D-2 (40 mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and as directed |
| 99 | M&L for plain cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate as incoping, including necessary form work and finished exposed surface of concrete all as specified. |
| 100 | Demolition of cement concrete is reinforced roofs, floors (other than ground floors) beams staircases, manhole covers, landing chhajjas and similar suspended wk (reinforcement cut as requited to facilitate demolition) |
| 101 | M&L pre cast cover RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in cover slab for manhole, septic tank etc set in cement mortar (1:6) including formwork all as specified and as directed. |
| 102 | M&L for plain cement concrete (1:2:4) type B-2 using 40 mm graded stone aggregate as in benching, haunching of man holes,in surface channels and drains. |
| 103 | Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n.exc 20 cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar work exc 10cm but n. exc 20cm wide for fair finish surfaces complete all as specified. |
| 104 | Mild steel TMT bars 10mm dia and over (and flat iron where quered),cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips or welded to flat iron complete all as specified. |
| 105 | Mild steel TMT bars 6mm to 8mmdia for stirrups and over (and flat iron where quered),cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips or welded to flat iron complete all as specified. |
| 106 | Cutting intoexisting manholes for connecting new drains, making good to pipe and rendering, cutting of existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4, type B-0, smooth finished and reforming benching as reqd for intodia/bore of pipe ‘150 mm’ complete |
| 107 | S/F 100mm cast iron soil, wast and vent pipes in any length with or without ears with cement joints fixed to wall incl taking out u/s pipe |
| 108 | S/F 100mm cast iron soil, waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors incl taking out old unserviceable pipes all as specified |
| 109 | Dismantling and breaking up old PVC drain pipes of75/110mm diajointed in cement mortarand taking out of trenches and removing materials from site of work complete all as specified. |
| 110 | S&F110mmbore PVC(SWR) pipesingle socketed, in any length fixed to wall with rubber ring joint, ISI marked complete all as specified. |
| 111 | S&F75mmbore PVC(SWR) pipesingle socketed, in any length fixed to wall with rubber ring joint, ISI marked complete all as specified. |
| 112 | S&F110mmbore PVC(SWR) pipesingle socketed, in any length laid in trenches or floor with rubber ring joint, ISI marked complete all as specified. |
| 113 | S&F 75mmbore PVC(SWR) pipesingle socketed, in any length laid in trenches or floor with rubber ring joint, ISI marked complete all as specified. |
| 114 | S&F PVC connections pipe 15mm with PTMT nuts of length 450mm in repairs |
| 115 | S&F 110mm bore (any radious)PVC (SWR) bend, ISI marked complete all as specified. |
| 116 | S&F 75mm bore (any radious)PVC (SWR) bend, ISI marked complete all as specified. |
| 117 | Cleaning of septic tank and soakage well any size by dewatering, taking out mud/sludge/liquid from septic tanks, soakage wellsgetting out and removing & depositing the sludge to a distance not exceeding 100meter in borrow pits, excavating borrow pits and covering the filled borrow pits with minimum 10cm thick layer of earth and 2 cm thick lime on top surface to prevent spread out of foul smell.After taking out sludge and solid deposits, the inside of the septic tankshall be cleaned with water, complete all as specified and directed. |
| 118 | Cleaning & clearing of underground sewage line not exceeding 150mm bore at any depth & description, alongwith manholes (by taking off manhole covers and refixing the same after cleaning) by removing any type of blockage including desilting and de-chocking manually by rodding pumping etc including disposal of sludge /sludge water at authorised dumping site as directed by the Engineer-in-Charge. |
| 119 | Cleaning of blockage manually by rodding, pumping etc and removing the deposited sludge/solid/liquid material, at authorised dumping site as directed by Engineer-in-charge, complete from the following :- |
| 120 | Water closte any description including trap and CI pipe line upto first manhole |
| 121 | Floor Trap/Nahni Trap upto Gully trap |
| 122 | Pipe from gully trap upto first manhole (excluding gully trap) |
