Construction Of Five Numbers Of Rcc Watch Tower For Proposed Tank Farm At Naoholia As Per Standard Drawing Including Supply Of All Materials Except Cement -GROUP A SEC A -1 Surface dressing of the ground including removing vegetation andin-equalities not exceeding 15 cm deep and disposal of rubbish, leadupto 50 m and lift upto 1.5 m.All kinds of soil 2 Collecting / excavating sand, soil, silt, ordinary earth from anysource, load into lorries, transport it to distant place of workincluding procuring earth and laying in layer of 150mm thickness andcompacting, profile properly made for taking measurement, including allmeasurable lead upto 30m and lift as required. (The contractor shall beresponsible for all formalities of supply of earth such as purchase ofland including royalties, monopoly / other statutory taxes as required from any distance.) 3 Earth work in excavation of foundation of structures as perdrawing and technical specification, including setting out, constructionof shoring and bracing, removal of stumps and other deleterious matter,dressing of sides and bottom, backfilling the excavation earth to theextent required and utilising the remaining earth locally for roadwork.)for Ordinary Soil by Manual Means (Depth upto 3 m) 4 Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinthlevel 136 (1 Cement 3 coarse sand (zone-III) 6 graded stoneaggregate 20 mm nominal size). 5 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level 11.53 (1 cement 1.5coarse sand (zone-III) 3 graded stone aggregate 20 mm nominal size). 6 Reinforcement for RCC work including straightening, cutting, bending,placing in position complete. - Upto plinth level Thermo- MechanicallyTreated bars of Grade Fe-500 D or more. 7 Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in foundation and plinth in Cement mortar 14 (1 cement 4 coarse sand). 8 Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in superstructure above plinth level up to floor V levelin all shapes and sizes in Cement mortar 14 (1 cement 4 coarsesand). 9 Laying Brick Flat Soling (75mm thick) including grading the base andspreading 25mm thick sand bed at bottom and grouting soling with cementmortar (prop. 13) and carrying all materials from a distance of upto30.00m. 10 Centering and shuttering including strutting, propping etc. and removalof form for Foundations, footings, bases of columns, etc. for massconcrete 11 Centering and shuttering including strutting, propping etc. and removalof form for Columns, Pillars, Piers, Abutments, Posts and Struts.12 Centering and shuttering including strutting, propping etc. and removalof form for Stairs, (excluding landings) except spiralstaircases. 13 Extra for additional height in centring, shuttering where everrequired with adequate bracing, propping etc. including cost ofde-shuttering and decentring at all levels, over a height of 3.5 m, forevery additional height of 1 metre or part thereof (Plan area to bemeasured) Suspended floors, roofs, landing, beams and balconies (Planarea to be measured). 14 Centering and shuttering including strutting, propping etc. and removalof form for Suspended floors, roofs, landings, balconies and accessplatform.15 Reinforced cement concrete work in walls (any thickness), includingattached pilasters, buttresses, plinth and string courses, fillets,columns, pillars, piers, abutments, posts and struts etc. above plinthlevel up to floor five level, excluding cost of centering, shuttering,finishing and reinforcement 11.53 (1 cement 1.5 coarsesand(zone-III) 3 graded stone aggregate 20 mm nominal size). 16 6 mm cement plaster of mix 13 (1 cement 3 fine sand). 17 12MM CEMENT PLASTER(14)- FINE SAND 18 Structural steel work riveted, bolted or welded in built up sections,trusses andframed work, including cutting, hoisting, fixing in positionand applying a primingcoat of approved steel primer all complete. 19 Painting with synthetic enamel paint of approved brand and manufactureto give an even shade Two or more coats on new work. 20 Providing and fixing ISI marked flush door shutters conforming to IS 2202 (Part I) decorative type, core of block board construction withframe of 1st class hard wood and well matched teak 3 ply veneering withvertical grains or cross bands and face veneers on both faces ofshutters.30 mm thick including ISI marked Stainless Steel butt hinges withnecessary screws. 21 Providing and fixing glazing in aluminium door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasket etc.complete as per the architectural drawings and the directions ofengineer-in-charge . (Cost of aluminium snap beading shall be paid inbasic item) With float glass panes of 4.0 mm thickness (weight not lessthan 10kg/sqm). 22 Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriateZ sections and other sections of approved make conforming to IS 733 andIS 1285, fixing with dash fasteners of required dia and size, includingnecessary filling up the gaps at junctions, i.e. at top, bottom andsides with required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading forglazing / paneling, C.P. brass / stainless steel screws, all complete asper architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately) Forfixed portion Anodised aluminium (anodised transparent or dyed torequired shade according to IS 1868, Minimum anodic coating of grade AC15). 23 Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar,bent to shape with hooked ends in R.C.C. slabs or beams during laying,including painting the exposed portion of loop, all as per standarddesign complete. 24 Finishing walls with water proofing cement paint of required shade Newwork (Two or more coats applied @ 3.84 kg/10 sqm)25 White washing with lime to give an even shade New work (three or more coats) 26 Providing and fixing ISI marked oxidised M.S. tower bolt black finish,(Barrel type) with necessary screws etc. complete 250x10 mm. GROUP A SEC B, 1 Carriage of material by mechanical transport including loadingunloading and stacking Cement, stone blocks, G.I., C.I., A.C. & C.C.pipes below 100 mm dia and other heavy materials Beyond 4KM and Upto5KM 2 Extra on Carriage of material by mechanical transport including loadingunloading and stacking Cement, stone blocks, G.I., C.I., A.C. & C.C.pipes below 100 mm dia and other heavy materials on every additional KMBeyond 5KM and Upto 10KM 3 Extra on Carriage of material by mechanical transport including loadingunloading and stacking Cement, stone blocks, G.I., C.I., A.C. & C.C.pipes below 100 mm dia and other heavy materials on every additional KMBeyond 10KM and Upto 20KM
