Supply Of Supply Of Tamping Arms, Hydraulic Squeezing Cylinders, Tamping Unit Basic Frames For The Use Of Tamping Machines.Supply Of Tamping Arms, Hydraulic Squeezing Cylinders, Tamping Unit Basic Frames For The Use Of Tamping Machines.,Hyd. Closing Cylin-Andhra Pradesh

Supply Of Supply Of Tamping Arms, Hydraulic Squeezing Cylinders, Tamping Unit Basic Frames For The Use Of Tamping Machines.Supply Of Tamping Arms, Hydraulic Squeezing Cylinders, Tamping Unit Basic Frames For The Use Of Tamping Machines.,Hyd. Closing Cylinder As Per Plasser Part No.Hzsa.G.150.273 For The Use Of 3X Machine.Specification As Under. 1.Squeezing Cylinder - 2E. 34. 41A Rdso Spec. No. Tm/Hm/6/312 [Rev.1] And Drg.No.Tm/014/07 [Rev-1] 2. Piston Rod Bush [ 2E. 34. 231 ] Rdso Specification No.Tm/Hm/6/383 And DrawingNo.Tm/0413 [Rev-1] 3. Piston For Sq.Cylinder [2E.36.457]. Rdso Specification No. Tm/Hm/6/383 & Drawing No.Tm/0581 [Rev-1] 4. Piston Rod For Sq.Cylinder [2E.36.452]. Material Made From Steel Of Grade 817M40 [En-24].Confirming To Bs:970, Part-Ii Specification Of Direct Hardening Alloy Steel [Hardness Of 30-35 Hrc Upto 1.25MmDepth]. 5. Seal Set Make: Plasser/Trellberg/ /Freudenberg/Simrit (Regarding Make Of Seal It Is To Be Ensured ByThe Consignee During Inspection Of The Material With Documentary Proof Of Purchase Of Seal From The SpecifiedBrands Mentioned In The Tender [Acceptable Make: Plasser Imp Or Its Equivalent] , Piston Rod Assy For For Csm/Duomatic As Per Plasser Part No. Hzsi- K -57- 5- 403 [AcceptableMake: Plasser Ind Or Its Equivalent] , Piston Rod Assy For Unimat As Per Plasser Part No. Hzs- 201 - 121 [Acceptable Make: Plasser IndOr Its Equivalent] , Hyd. Sq. Cylinder Male As Per Plasser Part No.Hzs.A.163.143 For The Use Of Unimat-4S.Specification As Under. 1.Squeezing Cylinder Male Body [ Cu 12. 501 ] Material Made Out Grade 709M40[En-19]Confirming To Bs:970[Pt.2], 1970 Specification For Direct Hardening Of Alloy Steels. 2. Piston Rod Bush [W.37.2093-1529].Material Specification As Per Annexure-A 3. Piston For Sq.Cylinder [W.37.2095] Material Specification As PerAnnexure-A 4. Piston Rod For Sq.Cylinder [Jt30.06A]. Rdso Specification No. Tm/Hm/6/253 & Drawing No.Tm/0562. 5.Seal Set Make: Plasser/Trellberg/ /Freudenberg/Simrit (Regarding Make Of Seal It Is To Be Ensured ByThe Consignee During Inspection Of The Material With Documentary Proof Of Purchase Of Seal From The SpecifiedBrands Mentioned In The Tender [Acceptable Make: Plasser Imp Or Its Equivalent] , Hyd. Sq. Cylinder Female As Per Plasser Part No.Hzs.G.163.144Nfor The Use Of Unimat-4S.Specification As Under. 1.Squeezing Cylinder Female Body [Cu12.501] Rdso Specification No. Tm/Hm/6/314(Rev.1] & Drawing No. Tm/016/07 (Rev-1). 2. Piston Rod Bush [W.37.2093-1529].Material Specification As PerAnnexure-A 3. Piston For Sq.Cylinder [W.37.2095] Material Specification As Per Annexure-A 4. Piston Rod ForSq.Cylinder [Jt30.06A]. Rdso Specification No. Tm/Hm/6/253 & Drawing No. Tm/0562. [Acceptable Make:Plasser Imp Or Its Equivalent] , Piston Rod Complete As Per Plasser Part No. Hzsi.K.36.426-J [Acceptable Make : Plasser OmcOr Its Equivalent] , Squeezing Cylinder Female As Per Plasser Part No. Hzsi.G.52.425 For The Use Of 3X Machine. 1.Squeezing Cylinder Body. Ud.19.1291. Material Made Out Of Grade 709M40 [En-19] Confirming To Bs:970[Pt.2].1790 Direct Hardening Of Alloy Steel. 2.Piston Rod Bush [2E.35.212]. Composition Of Material As PerAnnexure-A Enclosed. 3. Piston For Sq. Cylinder. [2E.35.303]. Rdso Specification No. Tm/Hm/6/109 And DrawingNo. Tm/0130. 4. Piston Rod For Sq. Cylinder [2E.35.306] Rdso Spec.No. Tm/Hm/6/227 & Drawing No.Tm/0536. 5.Seal Set Make: Plasser/Trellberg/ /Freudenberg/Simrit (Regarding Make Of Seal It Is To Be Ensured By TheConsignee During Inspection Of The Material With Documentary Proof Of Purchase Of Seal From The Specified BrandsMentioned In The Tender 6. Counter Weight : Ud-19-1230 Rdso Specifcation No. Tm/Hm/6/414 And Drawing No.Tm/02/18. [Acceptable Make: Plasser Imp Or Its Equivalent] , Squeezing Cylinder Assy. 09-3X As Per Plasser Part No.Hzsi-A-36-426. Specification AsUnder . 1.Squeezing Cylinder Body [Ud.19.1281] 2. Piston Rod Bush/Bearing Bush [Ud.19.287]. MaterialSpecification As Per Annexure-A Attached To The Tender Schedule. 3. Piston For Sq.Cylinder [2E.35.303] RdsoSpecification Tm/Hm/6/109 & Drawing No. Tm/0130. 4.Piston Rod For Sq.Cylinder [Ud.19.282]. Material Made OutOf Grade 817M40[En-24]. Confirming To Bs:970 Part-Ii. Specification Of Direct Hardening Alloy Steel. [AcceptableMake: Plasser Imp Or Its Equivalent] , Small Squeezing Cylinder Piston Rod Assy. As Per Plasser Part No. Hzsi-A-52.425J [AcceptableMake: Plasser Ind Or Its Equivalent] , Vibration Shaft Assembly (Rdso Specification No.Tm/Hm/6/127- Rev-2 & Drg. No. Tm/0321-Rev-1) As Per Plasser Part Nos. Consisting Of 1.Vibration Shaft Dl23.401-01 No. 2. Disc 2E22.35-2 Nos. 3.Castle Nut2E22.36-2 Nos. 4. Fitting Key 2E22.31-4Nos 5. Split Pin -8X80din94-02 Nos. Material For Disc And Nut Is En-8Grade Steel. (Acceptable Make : Plasser Ind Or Its Equivalent]Page 2 Of 7 Run Date/Time: 15/07/2021 17:13:28Scr Hq-Engg/South Central RlyTender Document , Tamping Arm Bolt. Consisting Of 1. Bolt As Per Plasser Part No. 2E31.04. Rdso Specification No.Tm/Hm/6/161. Rev-2. Drg. No. Tm/0425-Rev-2. 2. Spacer Sleeve -2E.31.02A (As Per Rdso Drawing No.Tm/0129-Rev-2. Specification - Tm/Hm/6/108-Rev-2). 3.Spring Washer -B.42Din.127. 4. Disc 2E.31.05. 5.HexNut M42x1.15 Din 934.8. [Acceptable Make: Plasser Ind Or Its Equivalent] , Tamping Arm Small Pin Assy Consisting Of 1. Bolt - G.20.13 (Rdso Specification No.Tm/Hm/6/197-Rev-2 And Drg. No. Tm/0510-Rev2) 2. Bush- G20.26B. (Rdso Specification No. Tm/Hm/6/195-Rev-2 And Drg. No. Tm/0508-Rev-2). 3.Disc-25Din1440 4.Spring Washer B.24.Din.127. 5. Hex Nut(Castle)M24x1.5Din934.8 [Acceptable Make: Plasser Ind Or Its Equivalent]. , Tamping Arm Small Pin Assembly(40Mm) Consisting Of Following 1. Bolt - Ud.19.221 (RdsoSpecification No. Tm/06/366-Rev-1 And Drg. No. Tm/06/16-Rev-1) 2.Spacer Bush (Sleeve)- Ud.19.222.1 (RdsoSpecification No. Tm/Hm/6/261-Rev-1 And Drg. No. Tm/0570-Rev-1). 3.Washer Vs24/Verz-01 No. 4. WasherGe20.14. 5. Hex Nut M24x1.5Din934.8 [Acceptable Make: Plasser Ind Or Its Equivalent ]. , Tamping Unit Basic Frame For Csm As Per Plasser Part Ud12.201.Li. [Acceptable Make: PlasserInd Or Its Equivalent] , Tamping Unit Basic Frame For Csm As Per Plasser Part Ud12.201.Re. [Acceptable Make: PlasserInd Or Its Equivalent] , Tamping Unit Basic Frame For Duomatic As Per Plasser Part Ud70.2301.Zre. [Acceptable Make:Plasser Ind Or Its Equivalent] , Tamping Unit Basic Frame For Duomatic As Per Plasser Part No. Ud70.2301.Zli. [Acceptable Make:Plasser Ind Or Its Equivalent] , Vibration Shaft Assembly For Duo Assembly Consisting Of 1.Vibration Shaft Ud22.501-01 No. 2.Disc 2E22.35-2 Nos. 3.Castle Nut 2E22.36-02 Nos. 4. Fitting Key 2E22.31-04Nos 5. Nut -Km-13-01 No. 6. LockPlate Mb-13-01 No. Material : The Shaft Shall Be Made Of Steel Of Grade 817M40 (En24) Confirming To Bs:970Part -Ii Specification Of Direct Hardening Alloy Steel And The Disc & Nut Shall Be Made Of Grade 080M40(En-8).Hardness-50 To 52 Hrc (Acceptable Make : Plasser Imp Or Its Equivalent ] , Vibration Shaft Assembly For Uni Assembly Consisting Of 1.Vibration Shaft Dl23.102-2-01 No. 2.Disc 2E22.35-2 Nos. 3.Castle Nut 2E22.36-02 Nos. 4. Fitting Key 2E22.31-04Nos 5. Split Pin 8X80din94-02Nos. Material : The Shaft Shall Be Made Of Steel Of Grade 817M40 (En24) Confirming To Bs:970 Part -IiSpecification Of Direct Hardening Alloy Steel And The Disc & Nut Shall Be Made Of Grade 080M40(En-8). Hardness-50 To 52 Hrc [Acceptable Make : Plasser Ind Or Its Equivalent] , Tool Tilting Cylinder Big Pin Assy For Uni-4S. As Per Plasser Part No. Ud15.1231. [AcceptableMake: Plasser Ind Or Its Equivalent ] , Tamping Arm Small (Modified) As Per Plasser Part Ud.15.4202 [Material Of Alloy Steel Casting OfGrade 709 M40 [En 19] Confirming To Bs970 (Pt.Ii-1970) Hardness-220 To 230Bhn. [Acceptable Make: PlasserInd Or Its Equivalent] , Tamping Arm As Per Plasser Part Ca21-2404 [Material Of Alloy Steel Casting Of Grade 709M40[En19] Confirming To Bs970 (Pt-Ii-1970) Hardness 220 To 230 Bhn]. [Acceptable Make: Plasser Ind Or ItsEquivalent] , Tamping Arm For 09-3X As Per Plasser Part Ca-21-2405. [Material Of Alloy Steel Casting Of Grade709M40 [En19] Confirming To Bs970 (Pt-Ii-1970) Hardness 220 To 230 Bhn]. [Acceptable Make: Plasser Ind OrIts Equivalent] , Tamping Arm Small -3X As Per Plasser Part Ud19-1902. [Material Of Alloy Steel Casting OfGrade 709M40 [En19] Confirming To Bs970 (Pt-Ii-1970) Hardness 220 To 230 Bhn]. [Acceptable Make: PlasserInd Or Its Equivalent] , Tamping Arm Small 3X As Per Plasser Part Ud19-1903. [Material Of Alloy Steel Casting OfGrade 709M40 [En19] Confirming To Bs970 (Pt-Ii-1970) Hardness 220 To 230 Bhn]. [Acceptable Make: PlasserInd Or Its Equivalent] , Tamping Arm For Mpt As Per Plasser Part Ca21.2303. [Material Of Alloy Steel Casting Of Grade709M40 [En19] Confirming To Bs970 (Pt-Ii-1970) Hardness 220 To 230 Bhn]. [Acceptable Make: Plasser Ind OrIts Equivalent ]

Refer document

Refer document

Refer document