Construction Of Non-Residential Building Of Block Dhari ( Nainital )
Tender Value
Ref. Documents
Estimated cost
Bid Submission
02 Aug 2021
0 days left
EMD
5.60 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhari → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Non-Residential Building Of Block Dhari ( Nainital )
BOQ
| NAME OF WORK:- CONSTRUCTION OF BLOCK OFFICE BUILDING AT DHARI,NAINITAL | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.in all kinds of soil. | 2.8.1 | 413.96 | cum |
| 2 | 2 | Filling available excavated earth (excluding rock) in trenches, plinthsides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, leadup to 50 m and lift upto 1.5 m. | 2.25 | 170.63 | cum |
| 3 | 3 | Supplying and filling in plinth with Jamuna sand under floors, includingwatering, ramming, consolidating and dressing complete | 2.27 | 33.29 | cum |
| 4 | 4 | Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | 2.25(a) | 79.1 | Cum |
| 5 | 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level in 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). | 4.1.8 | 122.16 | cum |
| 6 | 6 | Providing and laying in position cement concrete of 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) | 4.1.3 | 3.62 | cum |
| 7 | 7 | Brick work with F.P.S. bricks of class designation 75 in foundation and plinth inCement mortar 1:4 (1 cement : 4 coarse sand) | 6.1.1 | 31.99 | cum |
| 8 | 8 | Brick work with F.P.S. bricks of class designation 75 in foundation and plinth inCement mortar 1:6 (1 cement : 6 coarse sand | 6.1.2 | 53.47 | cum |
| 9 | 9 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) | 4.10. | 37.05 | sqm |
| 10 | 10 | 15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall. | 13.1 | 336.3 | sqm |
| 11 | 11 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. | 4.12 | 51.27 | per bag of 50 kg cement used in the mix |
| 12 | 12 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10of approved quality using 1.7kg per square metre on damp proof course aftercleaning the surface with brushes and finally with apiece of cloth lightlysoaked in kerosene oil. | 4.13. | 321.03 | sqm |
| 13 | 13 | Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) | 6.4.2 | 104.28 | cum |
| 14 | 14 | Half brick masonry with F.P.S. bricks of class designation 75 in superstructure abov plinth level upto floor V level inCement mortar 1:4 (1 cement :4 coarse sand) | 6.13.2 | 179.63 | sqm |
| 15 | 15 | Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks). | 6.15 | 179.63 | sqm |
| 16 | 16 | Providing and laying in position specified grade of reinforced cement concrete1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) | 5.1.2 | 87.26 | cum |
| 17 | 17 | Reinforced cement concrete work in walls (any thickness), includingReinforced cement concrete work in walls (any thickness), includingattached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. up to floor five level,excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate20 mm nominal size) | 5.2.2 | 25.17 | cum |
| 18 | 18 | Reinforced cement concrete work in Beam,suspended floor roof having slop up to 15 degree landing balcony shelf chajjas lintels band plain windoe cills staircase & sprial stair case etc. up to floor five level,excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate20 mm nominal size) | 5.3. | 144.83 | cum |
| 19 | 19 | Centring and shuttering including strutting,ropping etc. and removal of form forCentring and shuttering for foundations, footings, bases of columns, etc. for mass concrete. | 5.9.1 | 81.59 | sq.m |
| 20 | 20 | Centring and shuttering including strutting,ropping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. | 5.9.3 | 662.06 | sq.m |
| 21 | 21 | Centring and shuttering including strutting,ropping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. | 5.9.5 | 730.38 | sq.m |
| 22 | 22 | Centring and shuttering including strutting,ropping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts | 5.9.6 | 320.39 | sq.m |
| 23 | 23 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. TMT bars Fe500D | 5.22.6 | 35110.5 | KG |
| 24 | 24 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. | 10.25.2 | 1611.95 | kg |
| 25 | 25 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with dash fastener or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. | 10.13.1 | 354.58 | KG |
| 26 | 26 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and nuts as required including fixing of necessary butt hinges and screws and applyinFixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). | 10.15.1 | 4934.27 | kg |
| 27 | 27 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.)trusses etc., including cutting, hoisting, fixing in position and applying a primingcoat of approved steel primer, including welding and bolted with special shapedwashers etc. complete.Hot finished welded type tubes | 10.16.1 | 13527.5 | kg |
| 28 | 28 | Providing and fixing stainless steel (Grade 304) railling made of Hollow tubes, channels, plates etc. including welding, grinding, buffing,polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railling with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc.of required size, on the top of the floor or the side of waist slab with suitable arrangment as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) | 10.28 | 904.5 | kg |
| 29 | 29 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of\npurlins, rafters and trusses and including cutting to size and shape wherever required. | 12.5 | 386.5 | sqm |
| 30 | 30 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm) | 12.51.1 | 74 | mtr |
| 31 | 31 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Barge board (Upto 300 mm) | 12.51.4 | 86 | mtr |
| 32 | 32 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Gutter (600 mm over all girth) | 12.51.6 | 82 | mtr |
| 33 | 33 | Providing fixing thermal insulation of ceiling (under deck insulation)with Resin Bonded Fibre glass wool conforming to IS : 8183, density24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags,fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wiremesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building. | 12.34 | 316 | sqm |
| 34 | 34 | 12 mm cement plaster of mix1:6 (1 cement : 6 fine sand | 13.1.2 | 2016.87 | sq.m |
| 35 | 35 | 15 mm cement plaster on rough side of single or half brick wall of mix1: 6 (1 cement: 6 fine sand) | 13.2.2 | 1254.53 | sq.m |
| 36 | 36 | Smooth finishing of the exposed surface of R.C.C. work with 6 mm thickcement mortar 1:3 (1 Cement : 3 fine sand). | 5.23 | 662.06 | sq.m |
| 37 | 37 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm | 11.46.2 | 103.9 | Sqm |
| 38 | 38 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 60x60 cm | 11.41.2 | 546.7 | SQM |
| 39 | 39 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | 11.56.1 | 94.27 | sqm |
| 40 | 40 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Udaipur green marble | 11.23.5 | 183.67 | sqm |
| 41 | 41 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm includingpointing the joints with white cement and matching pigmentetc., complete.\n\n\n\n\n\n | 11.37 | 85.42 | sqm |
| 42 | 42 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. | 8.31 | 269.51 | sqm |
| 43 | 43 | Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick. | 11.13.1 | 87 | meter |
| 44 | 44 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction withframe of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on bothfaces of shutters:35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws\n\n\n\n\n | 9.21.1 | 53.61 | sq.m |
| 45 | 45 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). | 9.1.1 | 0.46 | Cum |
| 46 | 46 | Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for\nseparately, all complete as per direction of Engineer-in-charge. (Note:-Butt hinges and necessary screws shall be paid separately)Second class teak wood 35 mm thick shutters | 9.5.1.1 | 15.84 | sqm |
| 47 | 47 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or\nrebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Second class teak wood | 9.7.1 | 6.34 | sqm |
| 48 | 48 | Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :125x85x5.5 mm (heavy type) | 9.72.1 | 64 | each |
| 49 | 49 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm | 9.74.1 | 32 | each |
| 50 | 50 | Providing and fixing bright finished brass door latch with necessary screws etc. complete :300x16x5 mm | 9.75.1 | 12 | each |
| 51 | 51 | Providing and fixing bright finished brass handles with screws etc. complete125 mm | 9.81.1 | 24 | each |
| 52 | 52 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. | 9.82 | 12 | each |
| 53 | 53 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete | 9.83 | 2 | each |
| 54 | 54 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm | 9.96.2 | 32 | each |
| 55 | 55 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm | 9.97.2 | 64 | each |
| 56 | 56 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm | 9.100.1 | 64 | each |
| 57 | 57 | Providing and fixing aluminium hanging floor door stopper ISI marked anodisedTwin rubber stopper | 9.101.2 | 21 | each |
| 58 | 58 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows alll complete.With 4.0 mm thick glass panes. | 10.30.1 | 94.56 | sq.m |
| 59 | 59 | Providing & fixing fly proof wire gauze to windows, clerestory windows &doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides | 10.29.2 | 65.46 | sq.m |
| 60 | 60 | Providing&laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface prepration, first layer of slurry of cement@ o.488kg/sqm mixed with waterproofing compound &.0.253kg/sqm (b) laying second layer of fiber glass cloth when the first layer is still green. overlaps of joints of fiber glass cloth should not be less than 10 cm.(c)third layer of 1.5mm thickness consisting of slurru of [email protected]/sqm mixed with waterproofing [email protected]/sqm and course [email protected]/sqm thish will be allowed to air cure for 4 huors followed by wter curring for 48 hours. the entire treatment will be taken up to 30cm on parapit wall and tucked into groove in parapit all around(d) fourth &final layer of brick tiling with cement morter (which will be paid seprately .for purpose of measurement the entire treated surface will be measured. | 22.6. | 70.84 | sq.m |
| 61 | 61 | 12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 | 13.9.1 | 70.84 | sq.m |
| 62 | 62 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. | 13.21 | 15.54 | per bag |
| 63 | 63 | Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner. | 12.55 | 70.84 | sqm |
| 64 | 64 | Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as perIS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as perASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's\nspecification as per direction of Engineer-in-Charge all complete.With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles | 26.24.1 | 205.35 | sqm |
| 65 | 65 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits,switch boards etc., including providing with two coats of approved steelprimer etc. complete, all as per direction of Engineer-in-charge. | 9.154 | 631.8 | Kg |
| 66 | 66 | Providing and fixing plain lining with necessary screws/nuts & bolts/nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).12mm thick commercial ply conforming to IS : 1328 BWR type | 9.140.1 | 48.6 | Sqm |
| 67 | 67 | Providing and fixing 2nd class teak wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface.20 mm thick | 8.25.3 | 48.6 | sqm |
| 68 | 68 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patternshaving NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible\nas per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as perASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles | 26.23.1 | 421.29 | sqm |
| 69 | 69 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work)25 mm dia. nominal bore | 18.12.3 | 48 | mtr |
| 70 | 70 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 25 mm dia. nominal bore | 18.10.3 | 54 | mtr |
| 71 | 71 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall 20 mm dia. nominal bore | 18.10.2 | 42 | mtr |
| 72 | 72 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)20MM nominal bore | 18.17.1A | 10 | each |
| 73 | 73 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)25MM nominal bore | 18.17.1 | 8 | each |
| 74 | 74 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)20 mm nominal bore | 18.46.2 | 12 | each |
| 75 | 75 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)25 mm nominal bore | 18.46.3 | 10 | each |
| 76 | 76 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore | 18.18.3 | 6 | each |
| 77 | 77 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain &brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.this includes jointing of pipes & fittings with one step CPVC solventcement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes | 18.8.1 | 72 | mtr |
| 78 | 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain &brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solventcement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes | 18.8.2 | 45 | mtr |
| 79 | 79 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain &brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.\nThis includes jointing of pipes & fittings with one step CPVC solventcement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.25 mm nominal outer dia Pipes | 18.8.3 | 30 | mtr |
| 80 | 80 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank | 18.48 | 3000 | lit |
| 81 | 81 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms15mm nominal bore.. | 18.51.1 | 8 | each |
| 82 | 82 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:893115 mm nominal bore | 18.49.1 | 13 | each |
| 83 | 83 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15mm nominal bore. | 18.52.1 | 16 | each |
| 84 | 84 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore | 18.53.1 | 18 | each |
| 85 | 85 | Providing and fixing uplasticised PVC connection pipe with brassunions :30 cm length15 mm nominal bore\n | 18.21.1.1 | 34 | each |
| 86 | 86 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not lessthan 106 gms. | 18.65 | 10 | each |
| 87 | 87 | Providing and fixing PTMT grating of approved quality and colour.100 mm nominal dia. | 18.58,1,1 | 33 | each |
| 88 | 88 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mmWhite Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. | 17.1.1 | 9 | each |
| 89 | 89 | Providing and fixing white vitreous china pedestal type water closet (European typeW.C. pan with ISI marked white solid plastic seat and lid | 17.2.1 | 5 | each |
| 90 | 90 | White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C. brass pillar tap. | 17.7.4 | 14 | each |
| 91 | 91 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. | 17.8. | 14 | each |
| 92 | 92 | Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good\nthe walls wherever required :Kitchen sink without drain board 610x460 mm bowl depth 200 mm. | 17.10.2.2 | 2 | each |
| 93 | 93 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively. | 17.23 | 12 | each |
| 94 | 94 | providing fixing 8mm diaCP/SS jet with flexible tube up to 1 meter long with SS triangular plate to eureopean type WC of quality and make as approved by engineer in charge | 17.16A | 5 | each |
| 95 | 95 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.Flexible pipe32mm dia | 17.28.2.1 | 14 | each |
| 96 | 96 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. | 17.73.2 | 3 | each |
| 97 | 97 | Providing and fixing mirror of superior glass (of approv quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. with plastic moulded frame of approved make and shades with 6 mm thick hard board backing:Rectangular shape 453x357mm | 17.32.2 | 8 | each |
| 98 | 98 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. | 17.33 | 2 | each |
| 99 | 99 | providing &fixing PTMT liquid soap container 109 mm wide ,125mm high &12mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour,weighing not less than 105 gms | 17.71 | 2 | each |
| 100 | 100 | providing &fixing PTMT 15mm urinal spreader size 95x69x100mm with 1/2\"BSP thread and shapes, weighing not less than 60gms | 17.75 | 12 | each |
| 101 | 101 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes75 mm diameter | 12.41.1 | 30 | meter |
| 102 | 102 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories coupler 75mm diameter | 12.42.1.1 | 7 | each |
| 103 | 103 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories bend 75mm diameter | 12.42.5.1 | 9 | each |
| 104 | 104 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories single tee 75x75x 75mm diameter | 12.42.4.1 | 9 | each |
| 105 | 105 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes110 mm diameter | 12.41.2 | 90 | meter |
| 106 | 106 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories coupler110mm diameter | 12.42.1.2 | 15 | each |
| 107 | 107 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories bend 110mm diameter | 12.42.5.2 | 15 | each |
| 108 | 108 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories single tee 110x110x110mm diameter | 12.42.4.2 | 15 | each |
| 109 | 109 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110MM | 12.43.2 | 20 | each |
| 110 | 110 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised -PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.75MM | 12.43.1 | 20 | each |
| 111 | 111 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finishedWith F.P.S. bricksInside dimensions 455x610 mm and 45 cm deep for single pipe line : | 19.30.1.1 | 15 | each |
| 112 | 112 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honeycomb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m longcomplete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | 19.32.1 | 2 | each |
| 113 | 113 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately White sand stone - Exposed face machine cut and table rubbed with rough backing.) : | 8.14.4.5 | 245.6 | sqm |
| 114 | 114 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premouldedand prepolished, machine cut for kitchen platforms, vanity counters, windowsills , facias and similar locations of required size, approved shade, colourand texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment,epoxy touch ups, including rubbing, curing, moulding and polishing to edgesto give high gloss finish etc. complete at all levelsGranite of any colour and shade.Area of slab upto 0.50 sqm | 8.2.2.1 | 18.18 | sqm |
| 115 | 115 | Providing and fixing stone slab with table rubbed, edges rounded andpolished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embeddingthe stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size)as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade | 8.10.2 | 4.5 | sqm |
| 116 | 116 | Providing edge moulding to 18 mm thick marble stone counters, Vanitiesetc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge. Granite work | 8.3.2 | 122.4 | mtr |
| 117 | 117 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as\ndirected by Engineer-in- Charge:All kinds of soil | 2.1.1 | 424 | Cum |
| 118 | 118 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, ompacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. | 16.91.2 | 408.82 | sqm |
| 119 | 119 | Finishing walls with Acrylic Smooth exterior paint of required shadeNew work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm). | 13.46.1 | 433.75 | sq.m |
| 120 | 120 | providing and applying white cement based putty of average thickness 1mm of approved brand and manufacture, over plastered wall surface to prepare the surface even and smooth complete | 13.80. | 3687.86 | sq.m |
| 121 | 121 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shadeNew work (two or more coats) over and including priming coat with cement primer | 13.41.1 | 3254.12 | sq.m |
| 122 | 122 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shadeTwo or more coats on new work | 13.61.1 | 348.88 | sq.m |
| 123 | 123 | French sprit polishing :two or more coats on new works including a coat of wood fillar i/c all complete | 13.68.1 | 50.76 | sqm |
| 124 | 124 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement:3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over75mm thick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including finishing the topsmooth. | 4.17 | 61.2 | sq.m |
| 125 | 125 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.projections. | 5.30 | 128.6 | Mtr |
| 126 | 126 | Excavation in Hilly Areas in Ordinary Rock by mechanical means not requiring blasting (With out Dozer) Excavation in hilly area in ordinary rock not requiring blasting by mechanical means without using Dozer including cutting and trimming of slopes and disposal of cut material with a lift upto 1.5 m and lead upto 20 m as per Clause 1603.2. | MISC 1-1-2 | 218.75 | Cum |
| 127 | 127 | Excavation by mechanical means/ manual means in foundation trench or drain (not Exceeding 1.50 m in width or 10 Sqm on plan) including dressing of sides and ramming of bottoms lift up to 1.5 m including getting out the excavated soil and disposal of surplus excvated soil as directed with in lead of 50 m. in all kind of soil. | MISC 1-2 | 41.63 | Cum |
| 128 | 128 | Cement plum Masonry with 40% plum & 60% 1:3:6 cement concrete including supply of all material, labour, T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 of MORD Specifiction | MISC2-1 | 75 | Cum |
| 129 | 129 | R.R.stone masonry laid in 1:6 c/s in Retaining and breast wall including supply of all materials,labour and t&p required for proper completion of the work | MISC 1-4 | 73.13 | Cum |
| 130 | 130 | Cement concrete work with approved coarse sand & 16-22.40mm grit in proporation 4:2:1 including supply of all material, labour and T&P etc. required for th proper completion of work. | MORD11-4-3-2 | 1.5 | Cum |
| 131 | 131 | H.P. Stone filling in retaining walls, brest walls including supply of all material, labour, T&P etc required ror proper completion of the work | MISC 1-5 | 44 | Cum |
AI Tender Summary
Tender Timeline
Jul 15, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedAug 02, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 02, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender