Supply And Installation Of Microwave Frequency Arbitrary Wave Form Generator Upto 10 Ghz And Accessories-Punjab

Supply And Installation Of Microwave Frequency Arbitrary Wave Form Generator Upto 10 Ghz And Accessories 1. Number of Channels: 2 Analog outputs with 50 ohm output impedance 2. Output amplitude: 500 mV to 1 V range with 1mv resolution 3. Auxiliary Differential outputs: Differential outputs must be synchronous with 180 deg out of phase with 2 channels 4. Effective Frequency Output: DC to 10GHz 5. DAC Variable Sampling rate: Minimum 5 KSa/s to Maximum 25 GSa/s 6. DAC Resolution: 10 Bits or better 7. Analog Bandwidth (-3dB): 10 GHz 8. Waveform Memory: 2 Giga Samples on both channels 9. Wave Granularity: 1 point 10. Pulse width and repetition rate: high frequency Pulses as narrow as 30 to 60 pS and repetition rates of 160 pS or lower. 11. Rise time /fall Time: < 22 ps or better 12. Max Output Amplitude: 500 mVpp in Single ended 13. Random Jitter (Typical)- RMS: < 300fs or better 14. Spurious Free Dynamic Range: -40 dBc @ 10 GHz 15. 3rd Harmonic Distortion: ≤ -40 dBc or better 16. Phase Noise @ 10 GHz & 1KHz offset: -86 dBc/Hz or better 17. Flatness of the generated Signal: +0.8 dB to -1.5 dB or better 18. Channel to Channel skew: ±5 ps 19. Wave form Generation Capabilities (IQ & RF Waveforms): It should create Pulse Train. Each Pulse Train can have its own Carrier Frequency, Amplitude and Phase offset from other Trains. Each Pulse train is made of multiple pulse groups [Pulse waveform, Dead time, and Combined Pulse Groups (Pulses groups added in time)]. Pulse Shapes – Gaussian, Lorentzian, Rectangular, Trapezoidal, Raised Cosine, Exponential, Sawtooth & Custom Shape Modulation Support: Chirp Sequence: Sequence of Chirps, used in Automotive Radar Piece wise LFM: Within a Pulse, multiple Chirps with different slopes can be defined Non-Linear FM (NLFM) with Taylor weighted Symmetrical and Non- Symmetrical functions Digitally Modulations: QPSK and BPSK with Rectangular/Raised Cosine/Root Raised Cosine filters Define transition/rise time with linear or Cosine profile when switching frequency/ Phase Pulse Parameters including Start Time, Rise Time, Off Time, Fall Time, Pulse Width, and impairments like Droop, Overshoot, and Ripple, Ripple frequency. Create Combined Pulse Group Waveforms as Sequence. Inter and Intra pulse hopping should be defined. Staggered PRI & constant, Stepped, or user defined Amplitude, Frequency and Phase Change from Pulse to Pulse in a Pulse Group. Adding Edge Jitter/Width & provision to add Noise. Antenna Scan – Horizontal Scan, Circular Scan with Horizontal and Vertical Target Location, Beam width in both Azimuth and Elevation. 20. Pulse Creation Software: It should be available with parameters like Rise Time, Fall Time, Pulse Width etc… 21. External clock out / in: 50Ω, AC Coupled 22. Display Characteristics: Built in LED display with touch screen (only remote USB or ethernet units will not be accepted) 23. Operating System: Windows 10 or later with HDD to store signals. 24. Interface: LAN, USB, VGA with Matlab, Labview drivers also or general VISA programming tools. 25. Operating Temp. Range: 15 °C to +45 °C 26. Mains Supply: 230V, 50 Hz (Nominal) 27. Warranty: 3 Years 28. Accessories: Cables 0.5 m 4 pcs: 2.92 mm male-male cable hand formable with 0.085 outer dia 50 ohms (give female if port has male connector) minicircuits or microcoax or equivalent. Interconnect grade not VNA grade armoured precision test grade. Cables 2.5m 4 pcs: 2.92 mm male-male cable hand formable with 0.085 outer dia 50 ohms (give female if port has male connector) minicircuits or microcoax or equivalent. Interconnect grade not VNA grade armoured precision test grade. Torque wrench: Torque wrench for 2.92 mm connectors Adapters: If any adapters are needed please quote. Finance bid: In finance bid quote for accessories and main unit separately. 29. Make in India Class I and Class II: Provide documents for class II or Class I supplier. In case of OEM not quoting we need statement from OEM and Local collaborator for class II or Class supplier. Service /calibration centre: OEM must have a NABL accredited service/calibration facility in India Repairs: For repairs during warranty manufacturer/local supplier must give Bank Guarantee. For repairs outside warranty local office of OEM or local supplier should give Indemnity bond to take instrument for repairs.

Refer document

Refer document