Repair/Rewinding Of Unserviceable Motors , Pump Sets , Starters , Panel Boards Incl Switch Gears , Repair/Maint Of Ro Plant , Dosing Pumps Including Cleaning Of Ug Sumps Ohts And Other Allied Misc Connected Works Of Ascone Node And Jalipa Mil Stn Under
Tender Value
Ref. Documents
Estimated cost
Bid Submission
30 Jul 2021
0 days left
EMD
36000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
GE (A) BARMER → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair/Rewinding Of Unserviceable Motors , Pump Sets , Starters , Panel Boards Incl Switch Gears , Repair/Maint Of Ro Plant , Dosing Pumps Including Cleaning Of Ug Sumps Ohts And Other Allied Misc Connected Works Of Ascone Node And Jalipa Mil Stn Under Ge ( Repair/Rewinding Of Unsv Motors , Pump Sets , Starters , Panel Boards Incl Switch Gears , Repair/Maint Of Ro Plant , Dosing Pumps Including Cleaning Of Ug Sumps Ohts And Other Allied Misc Connected Wks Of Ascone Node And Jalipa Mil Stn Under Ge ( A ) Barmer
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 10-Jul-2021 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 17-Jul-2021 |
| 2 | 21-Jul-2021 | Postponement | Date | 27-Jul-2021 |
| 3 | 29-Jul-2021 | Postponement of tender | Date | 30-Jul-2021 |
BOQ
| Name of Work : REPAIR/REWINDING OF UNSERVICEABLE MOTORS,PUMP SETS, STARTERS, PANEL BOARDS INCL SWITCH GEARS,REPAIR/MAINT OF RO PLANT, DOSING PUMPS INCLUDING CLEANING OF UG SUMPS OHTS AND OTHER ALLIED MISC CONNECTED WORKS OF ASCONE NODE AND JALIPA MIL STN UNDER GE (A) BARMER | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Dismantling existing electric motor with pump, 1/1.5/3/3.20 HP electric driven 3 phase 415 volts from foundation after disconnecting electric connection and transporting the same workshop for repair and refixing the same after repair and making electric connection, and commissioning including testing complete all as specified and directed by Engineer-in-Charge.\nNote: Replacement items shall be measured and paid separately . | 5 | Each\njob | |
| 2 | 2 | All as per above item no.1.00 but capacity 5/6.5/7.5 HP | 4 | Each\njob | |
| 3 | 3 | All as per above item no.1.00 but capacity 10 HP | 2 | Each\njob | |
| 4 | 4 | All as per above item no.1.00 but capacity 12.5/15 HP | 4 | Each\njob | |
| 5 | 5 | All as per above item no.1.00 but capacity 20 HP | 2 | Each\njob | |
| 6 | 6 | All as per above item no.1.00 but capacity 25 HP | 2 | Each\njob | |
| 7 | 7 | All as per above item no.1.00 but capacity 40 HP | 4 | Each\njob | |
| 8 | 8 | All as per above item no.1.00 but capacity 60 HP | 2 | Each\njob | |
| 9 | 9 | Dismantling and Opening the motor, cutting & removing the burn out winding, cleaning the slots of stator & rotar with cleaning agent and rewinding the Induction motor capacity 1/1.5/3/3.2 HP 3 phase 415 volts with super enameled copper wire of same gauge & same no of turns of existing make including E class insulation material, varnishing and balancing rotor connection earning the stater winding and assembling all part of motar pump and commissioning including testing to entire satisfaction of Engineer-in-Charge.\n | 5 | Each\njob | |
| 10 | 10 | All as per above item no.9.00 but capacity 5/6.5/7.5 HP | 4 | Each\njob | |
| 11 | 11 | All as per above item no.9.00 but capacity 10 HP | 2 | Each\njob | |
| 12 | 12 | All as per above item no.9.00 but capacity 12.5/15 HP | 4 | Each\njob | |
| 13 | 13 | All as per above item no.9.00 but capacity 20 HP | 2 | Each\njob | |
| 14 | 14 | Dismantling and Opening the motor, cutting & removing the burn out winding, cleaning the slots of stator & rotar with cleaning agent and rewinding the Centrifugal pump set motor capacity 25 HP 3 phase 415 volts with super enameled copper wire of same gauge & same no of turns of existing make including E class insulation material, varnishing and balancing rotor connection earning the starter winding and assembling all part of motar pump and commissioning including testing to entire satisfaction of Engineer-in-Charge.\n | 2 | Each\njob | |
| 15 | 15 | All as per above item no. 14.00 but capacity 40 HP | 4 | Each\njob | |
| 16 | 16 | All as per above item no. 14.00 but capacity 60 HP | 2 | Each\njob | |
| 17 | 17 | Dismantling and Opening the mono block pump set, 1 HP to 6.50 HP capacity of any model after disconnecting electric connection and opening the motor, checking the serviceability of spares parts and replacing the defective spare parts packing etc, & any type of lathe wok for fixing bearing, bush, are and transporting the same workshop for repair and refixing the same after repair and making electric connection including testing complete all as specified and directed by Engineer-in-Charge.\nNote: 1- Spares such as gasket, grease, nuts & bolts washers, shaft sleeve, bush, gland packing etc are deemed to including the item rate.\n2- Bearings, impellers, shaft if required to be replaced, will be measured and paid separately.\n | 6 | Each\njob | |
| 18 | 18 | All as per above item no. 17.00 but capacity 7.5 HP to 15 HP | 10 | Each\njob | |
| 19 | 19 | All as per above item no. 17.00 but capacity 20 HP to 25 HP | 4 | Each\njob | |
| 20 | 20 | All as per above item no. 17.00 but capacity 40 HP to 60 HP | 6 | Each\njob | |
| 21 | 21 | Supply only bearings (driving end & non-driving end set) suitable size for 0.5 HP to 3 HP pump set (as per existing make & model). | 2 | Set | |
| 22 | 22 | All as per above item no. 21.00 but capacity 5 HP to 7.5 HP | 2 | Set | |
| 23 | 23 | All as per above item no. 21.00 but capacity 10 HP to 15 HP | 10 | Set | |
| 24 | 24 | All as per above item no. 21.00 but capacity 20 HP to 25 HP | 4 | Set | |
| 25 | 25 | All as per above item no. 21.00 but capacity 40 HP to 60 HP | 6 | Set | |
| 26 | 26 | Supply only pump impeller made of bronze suitable size for 12.5 / 15 HP centrifugal pump set. (as per existing make & model) | 2 | Each | |
| 27 | 27 | All as per above item no. 26.00 but capacity 20 HP | 1 | Each | |
| 28 | 28 | All as per above item no. 26.00 but capacity 25 HP | 1 | Each | |
| 29 | 29 | All as per above item no. 26.00 but capacity 40 HP | 2 | Each | |
| 30 | 30 | Supply only stainless steel shaft with brass bush suitable size for 20 HP to 25 HP centrifugal pump set. (as per existing make & model) | 1 | Each | |
| 31 | 31 | All as per above item no. 30.00 but capacity 40 HP | 2 | Each | |
| 32 | 32 | S & F in replacement of coupling rubber bush between motor and pump 12.5/15/20/25 HP complete with rubber,CI/MS flange and rings, nuts, bolt & washers including lath work for cutting holes for both shafts and providing key etc complete all as specified and directed by Engr-in-charge. | 6 | Each\njob | |
| 33 | 33 | All as per above item no. 32.00 but capacity 40 HP | 4 | Each\njob | |
| 34 | 34 | All as per above item no. 32.00 but capacity 60 HP | 2 | Each\njob | |
| 35 | 35 | M&L for Gland packing of pumps of capacity 5 HP to 25 HP with hemp or asbestos impregneted with teflon packing by completely removing the old gland packings and necessary greasing of the gland bush nuts and bolts complete all as specified and directed by Engr-in-charge. | 12 | Each\njob | |
| 36 | 36 | All as per above item no. 35.00 but capacity 40 HP to 60 HP | 8 | Each\njob | |
| 37 | 37 | Supply and fix in repairs Air release valve made out of gunmetal suitable for 15 to 40 HP motor pump set complete all as specified and directed by Engg-in-charge. | 6 | Each\njob | |
| 38 | 38 | S & F in replacement CI foot valve of size 100 mm bore for under ground sump suction CI/GI line including nipple of suitable size, welding connection and testing complete all as specified and directed by Engineer-in-charge. | 6 | Each\n | |
| 39 | 39 | All as per above item no. 38.00 but size 80 mm bore | 6 | Each\n | |
| 40 | 40 | Supply and laying of 80 mm bore dia GI tubing, medium grade galavanised with all fittings and fixed to walls / celing / laid in floor suitable for pump suction pipe, connection, testing and commissioning, incld taking down / out of old u/s existing pipe complete all as specified and directed by Engineer-in-charge. | 24 | RM | |
| 41 | 41 | All as per above item no. 40.00 but Dia 100 mm bore | 18 | RM | |
| 42 | 42 | Supply & fixing in replacement of Timer suitable for stater of ML-1.5/2/3/4, MNX 32 | 5 | Each | |
| 43 | 43 | Supply and fixing in replacement Power Contactor 3 pole AC 3 415 V Long life Auxiliary Contact 1 NO + 1 NC with suitable timer and overload relay of rating 50A suitable for 40 HP 3 Phase induction Motor as per existing make complete all as specified and directed by Engineer-in-charge.\nCat no. TC1 D5011 of L&T and it's equivalent make of Seimens / C&S Electricals / Schneider | 3 | Each | |
| 44 | 44 | All as per above item no. 43.00 but suitable for 25 HP capacity | 2 | Each\n | |
| 45 | 45 | All as per above item no. 43.00 but suitable for 20 HP capacity | 2 | Each\n | |
| 46 | 46 | Supply and fixing in replacement thermal over load relay for ML-2 / 3 contactors upto 42 Amps as per existing make & model complete all as specified and directed by Engineer-in-charge. | 2 | Each\n | |
| 47 | 47 | Supply and fixing in replacement thermal over load relay for ML-1 / 1.50 contactors upto 16 Amps as per existing make & model complete all as specified and directed by Engineer-in-charge. | 4 | Each\n | |
| 48 | 48 | M&L for disconnecting / removing the old unserviceable starters from the panel and supply and fix DOL starter for AC, 415V 50 Hz 3 phase suitable for 1 HP to 3 HP capacity of electric motor with relay protection complete all as directed. | 4 | Each\n | |
| 49 | 49 | All as per above item no. 48.00 but suitable for 5 HP to 10 HP capacity | 2 | Each\n | |
| 50 | 50 | Supply and fixng in replacement of ML-3, fully automatic star Delta starter suitable for 40 HP pump set, 3 phase 415 volt, 50 Hz, 50 Amps, with complete accessories.\nMake : ML 3 FASD cat no. SS 90730 of L&T or its equivalent make of Siemens / C&S Electricals / Havells / Standard. | 1 | Each | |
| 51 | 51 | Supply and fixng in replacement of ML-1.5, fully automatic star Delta starter suitable for 25 HP pump set, 3 phase 415 volt, 50 Hz, relay range 20-32 Amps, with complete accessories.\nMake : ML 1.5 FASD cat no. SS 91855 of L&T or its equivalent make of Siemens / C&S Electricals / Havells / Standard. | 1 | Each | |
| 52 | 52 | Supply and fixng in replacement of ML-1, fully automatic star Delta starter suitable for 12.50 HP pump set, 3 phase 415 volt, 50 Hz, relay range 9-14 Amps, with complete accessories.\nMake : MK-1 FASD cat no. SS 96254 of L&T or its equivalent make of Siemens / C&S Electricals / Havells / Standard. | 1 | Each | |
| 53 | 53 | Supply and fixing in replacement single phase preventor suitable for 12.5/15/20/25 HP motors as per existing make & model complete all as specified and directed by Engineer-in-charge. | 4 | Each\n | |
| 54 | 54 | Supply and fixing in replacement single phase preventor suitable for 40 HP motors as per existing make & model complete all as specified and directed by Engineer-in-charge. | 2 | Each\n | |
| 55 | 55 | Supply and fixing in replacement Aluminium strip 20 x 3.15 mm as per existing make & model complete all as specified and directed by Engineer-in-charge. | 50 | RM | |
| 56 | 56 | M&L for earthing complete with galvanized earth plate electrode of size 60cm x 60cm x 6 mm thick burried directly in ground vertically at a depth not less than 2.25 metre deep below normal ground level with top edge of the plate not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt, filling in alternate layer and electrode connections by using 25 X 4 MM size of galvanized iron strip by means of bolts, nuts, check nuts and washers made of galvanized earth and protected by light grade 40 mm dia GI pipe connected to main switch board or main control board, and GI pipe light grade 20 mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC 1: 2: 4 type C2 including excavation and earth work, disposal of surplus soil to a distance not exc. 50 mtr all as specified and as shown on Plate No 3 of SSR Part I (2009) and Part II (2010) incl dismanteling of existing unserviceable earth pit complete all as specified and directed by Engr-in-Charge. \nNote: \n1. The earh resistant value must be well below of 5 ohm irrespective to seasons and any unforeseen condition.\n2. Earth should be free from stone. \n3. Item includes the cost of GI pipe up to 7.5m for protection of earth strip, any variation in length beyond 7.50 m shall be measured separately.\n4. Item includes cost of GI strip up to 7.5 m,any variation in length beyond 7.50 m shall be measured separately. | 4 | Each\njob | |
| 57 | 57 | Supply & fixing in replacement indicator LED lamps neon type on each phase with standard colours and pin / plug type to match with existing ( set of 03 Nos) and all as specified and directed by Engineer-in-charge. | 4 | Each set | |
| 58 | 58 | Supply and fix in replacement of MCCB 4 POLE 25 KA 160 Amps in existing panel the make should be of the same of existing MCCB to mach with existing slot, holes/surface complete all as specified and directed by engineer in charge. | 2 | Each | |
| 59 | 59 | All as per above item no. 58.00 but MCCB 4 POLE 10 KA 63Amps | 2 | Each | |
| 60 | 60 | Supply and fix in repairs motor fan and cover suitable for 12.5 / 15 HP motor cap with nut bolts & washers etc as per existing make & model complete all as specified and directed by Engineer-in-charge. | 4 | Each | |
| 61 | 61 | All as per above item no.60.00 but capacity 20 HP motor | 1 | Each | |
| 62 | 62 | Supply and fix in repairs centrifugal motor fan and cover suitable for 25 HP motor cap with nut bolts & washers etc as per existing make & model complete all as specified and directed by Engineer-in-charge. | 1 | Each | |
| 63 | 63 | All as per above item no.62.00 but capacity 40 HP motor | 1 | Each | |
| 64 | 64 | Supply and fixing in replacement electric motor terminal plate made of backlite base with brass terminal with nut, bolts & washers suitable for 12.5/15/20/25/40 HP motors as per existing make & model complete all as specified and directed by Engineer-in-charge. | 10 | Each\n | |
| 65 | 65 | M&L painting with two coats of synthetic enamel paint on steel surfaces of valvesof size 80mm to 200mm (in any position) including scraping and removing old paint complete all specified and directed by Engineer-in-charge. | 15 | Each\njob | |
| 66 | 66 | M&L painting with two coats of synthetic enamel paint including scraping and removing old paint from steel surfaces of valve chamber cover of any size complete all specified and directed by Engineer-in-charge. | 6 | Each\njob | |
| 67 | 67 | M&L applying two coats of synthetic enamel paint on pump,motor,cast iron pipes installed at pump (as per MES colour code) inlet and outlet pipe, header, GI suction pipe, from sum bottom to pump ,including writing letter/figure 5mm thick and 4 cm in height with black paint over white base in capital letter complete all as specified and as directed by Engineer-in-charge.\nNote: Subject matter for writing shall be provided by Engineer-in-charge. | 12 | Each\njob | |
| 68 | 68 | Chemical analysis and testing of water sample through registered lab including collection of water at source as directed by Engineer-in-charge and submitting test report to department complete all as specified and directed by Engineer-in-charge. | 4 | Each\nTest\nJob | |
| 69 | 69 | Bactorilogical test of water sample through registered lab including collection of water at source as directed by Engineer-in-charge and submitting test report to department complete all as specified by Engineer-in-charge. | 4 | Each\nTest\nJob | |
| 70 | 70 | Inspection, checking of defect, repair / replacement of defective parts, sansor and maintenance of existing RO Plant of capacity 6000 liters per Hrs(02 NOS) (Make: - ROCHEM) installed at Jalipa Pump House, AND 17 MAC as per maintenance manual of manufacturer to meet the required condition of water by back washing cleaning of membrane, cleaning of cartridge filter, servicing of chemical dozer, calibration of level indicator, cleaning of chemical Tank and all control valves etc complete all as specified and directed by Engineer-in-charge.\nNote:\n (a) The periodicity of visit is normally one month interval but in case of some emergency within 24 hours to be attended as directed by Engineer-in-Charge, \n(b) Spare parts for replacement and chemical required for servicing of RO plant shall be measured and paid for separately under respective item of Sch ‘A’, \n(c) The cost of replacement of small parts such as nuts, bolts, washer, screws, thimble lugs, gasket, rubber washer, wires etc shall be deemed to be included in unit rates quoted and nothing extra shall be admissible on this account\n(d) All tools, plant, equipment etc required for servicing shall be deemed to be included in unit rates quoted by the contractor | 11 | Each\nVisit | |
| 71 | 71 | All as per above Item No 70 but for the RO plant located at JCO Mess at near 17 Garud Line at Jalipa Military Station | 11 | Each\nVisit | |
| 72 | 72 | S & F in replacement of following existing defective / unservicable part of RO plant with new one of the same make and type / model No including testing complete. | |||
| 73 | 72.01 | Supply only for replacement,Cartridge filter 2.5\" x 20\" of RO plant with the same make and type / model number to match with existing complete all as specified and directed by Engineer-in-charge. | 240 | Each | |
| 74 | 72.02 | Supply only for replacement,Cartridge filter 1.5\" x 10\" of RO plant with the same make and type / model number to match with existing complete all as specified and directed by Engineer-in-charge. | 141 | Each | |
| 75 | 72.03 | Supply only Membrane 4” x 40” (CPA2- 4040).\nMake: DOE / Hydronautics. | 9 | Each | |
| 76 | 72.04 | Supply only Membrane 8” x 40” (CPA2- 8040).\nMake: DOE / Hydronautics. | 3 | Each | |
| 77 | 72.05 | Supply only rubber pneumatics tube,house conforming to IS-446187,type 2 of size 1.50\"\nMake: DOE / Hydronautics. | 35 | Each | |
| 78 | 72.06 | Supply only Water pressure gauge 100 mm dia | 3 | Each | |
| 79 | 72.07 | Supply only PVC pressure pipe 40mm bore heavy duty . | 30 | RM | |
| 80 | 72.08 | Supply only anti scalant solution in container. | 70 | Ltrs | |
| 81 | 72.09 | Supply only activated carbon 900 IV | 400 | KG | |
| 82 | 72.1 | Supply only sand gravel mixture for filter | 600 | KG | |
| 83 | 72.11 | Supply only Multiport Valve. | 2 | Each | |
| 84 | 73 | Supply and fix in repair RO plant automated control panel based on in built programmable logic controller (PLC) with the following functions\n(i) Automated start up operation activated by single push button.\n(ii) Self diagnostic built in test equipment with automatic failsafe routines for various fault conditions and status display with diagnostic charts on front panel.\n(iii) Manual override for emergency operations.\n(iv) Operation mode control: The RO plant should be able to undergo various modes of operation which execute and conclude automatically with appropriae display on the control panel, enabling easy opertion of the RO plant. The control panel should facilitate the following modes of opertion /maintenance:\n(a) Automated start up sequence, (b) Stop and rinse mode,(c) Chemical cleaning mode\n(d) Preservation mode,(e) Sand filter backwash mode, (f) Op pressure increase, (g) Op pressure decrease, (h) Fault reset mode\n(v) Manual override functions: During the manual operation the following safties/controls are required: (a) Whenever the raw water pump trips the high pressure pump and all other pumps shall automatically trip.\n(b) Till the raw water pump does not start the high pressure pump shall not start.\n(c) there must be option to show readings of pH, conductivity ad flow during manual mode.\nNote: (i) The rate quoted deemed to be included the cost of pH sensor , conductivity meter, TDS meter, flow meter, all pressure switches, automated control valves, necessary piping, joints and its accessories.\n(ii) The rate quoted deemed to be included the cost of wiring of the electrical equipments, necessary, foundation work for fitment of the control panel, and connecting of incoming power cable complete. | 1 | Each \nJob | |
| 85 | 74 | Cleaning of valve pit chamber of any size by taking out mud and muddy water and depositing the same to a distance n. exc 20 m from the pit including swipping, free from any type of dirt by washing complete all as per specified and directed by Engg-in-charge. | 20 | Each | |
| 86 | 75 | Supply and fixing in repalcement of High pressure feeder pump set (vertical type) motor, electric driven 5.5 HP, 3 Phase, 415 V , 50Hz suitable for RO plant at 17 Mac.\nMake:- Krilosker / Lubi or its equivalent. | 1 | Each\n | |
| 87 | 76 | Supply and fixing in repalcement of Mono block pump set motar, electric driven 3 HP, 3 Phase, 415 V , 50Hz suitable for RO plant at 17 Mac.\nMake:- Krilosker / Lubi or its equivalent. | 1 | Each\n | |
| 88 | 77 | M&L for framed work for platform (as per existing model ) of RO plant installation complete including replacement of stainless steel pipe & joints with breezing including framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. for necessary welding works required to the platform incld apply one coat of red-oxide primer and two coat of water-resistance paint ( tint will be approved by GE), including removing the rusted body of platform & staging structure for RO plant installation complete all as per specified and directed by Engg-in-charge.\nLocation:- RO plant at 17 Mac | 1 | Each\nJob | |
| 89 | 78 | All as per above item no.77.00 but Location:- RO plant at MES pump house | 1 | Each\nJob | |
| 90 | 79 | M&L cleaning of RCC under ground sump of capacity 2.00 lakh gallons at jalipa dewatering the sump with water lifting pump, descaling internal surfaces of under ground sump with wire brush, removing the deposited mud from inside the sump, washing with bleaching powder and flush water two times and dewatering, applying two coats of lime wash inside the sump including writing capacity of tank, date of cleaning with synthetic enamel paint of white tint over black base (size of letter 5mm thick and 15 cm in height) complete all as specified and directed by Engineer-in-charge. | 1 | Each\njob | |
| 91 | 80 | All as per above item no. 79 but capacity 1.00 lakh gallons, at Jalipa | 2 | Each\njob | |
| 92 | 81 | All as per above item no. 79 but capacity 75000 gallons, at Jalipa | 2 | Each\njob | |
| 93 | 82 | All as per above item no. 79 but capacity 50000 gallons, at Jalipa | 2 | Each\njob | |
| 94 | 83 | All as per above item no. 79 but capacity 25000 gallons, at Jalipa | 3 | Each\njob | |
| 95 | 84 | All as per above item no. 79 but capacity 20000 gallons, at Jalipa | 3 | Each\njob | |
| 96 | 85 | All as per above item no. 79 but capacity 20000 gallons, at Ascone node and Jalipa mil stn | 7 | Each\njob | |
| 97 | 86 | M&L cleaning of RCC over head tank capacity 75000 gallons at Jalipa by descaling internal surfaces of OHT with wire brush, removing the deposited mud from inside the tank, washing with bleaching powder and flush water two times and dewatering including writing capacity of tank, date of cleaning with synthetic enamel paint of tint white over black base (Size of letter 5mm thick and 15cm in height) complete all as specified and as directed by Engineer-in-charge.\nNote:- Cleaning of the tank must be performed with all neccesary measures for safety of working person. | 1 | Each\njob | |
| 98 | 87 | All as per above item no. 86.00 but capacity 50000 gallons, at Jalipa | 1 | Each\njob | |
| 99 | 88 | All as per above item no. 86.00 but capacity 25000 gallons, at Jalipa | 3 | Each\njob | |
| 100 | 89 | M & L for cleaning of CI pipe of over head tanks such as water rising main,wash out,overflow, inside the pipe & on the mouth of delivery pipe including all fittings by descaling,removing mud by descaling solution complete all as specified and directed by Engr-in-charge. | 6 | Each\njob | |
| 101 | 90 | M&L replacement of rusted cover of OH tank / under ground sump entrance way cover made of MS sheet 3mm thick off sizes to suit site requirement. Sheet welded with angle iron frame including one coat of red oxide primer and two coats of black synthetic enamel paint, including grouting arrangement, angle iron frame of 50 x 50 x 6mm complete all as specified and directed. | 130 | KG | |
| 102 | 91 | Taking out for repairs unserviceable spindle of cast item sluice valve from pit / column of size 150/100/80 bore & carrying to the workshop for cutting, threading, grinding etc and refixing the same after repair complete all as specified & directed. | 15 | Each \nJob | |
| 103 | 92 | Supply and fix gland packing with hemp or asbestos packing impregneted with graphite or teflon or fibre board gasket for sluice valve of 80 / 100 / 150 mm dia size bore/pipe line including taking down old gland packing complete all as specified and directed by Engineer-in-Charge | 30 | Each\nJob | |
| 104 | 93 | Supply and fixing in repair check nut suitable for spindle of sluice valve of size 80 / 100 / 150 mm sluice valve as diredted by Engineer-in-chagre. | 10 | Each | |
| 105 | 94 | Taking out of u/s Wheel shaft of CI sluice valve size of 500 mm dia, from valve pit / column pipe incld carrying to the workshop, cutting, threading, grinding, machining, etc and refixing the same after repair complete. Incld replace of old gland packing fibre gasket by new one and remove rust & old paint of sluice valve body by sand papering and apply new painting same as existing color & quality complete all as specified and diredted by Engineer-in-chagre. | 1 | Each\nJob | |
| 106 | 95 | Dismantling of existing Random Rubble stone masonry valve pit of Internal size 450 x 450 x 600mm. including stacking serviceable material and removal of unserviceable material from site complete all as specified and directed by Engineer-in-charge. | 3 | Each | |
| 107 | 96 | Dismantling of existing Random Rubble stone masonry valve pit of internal size 1050x750x1000mm. including stacking serviceable material and removal of unserviceable material from site complete all as specified and as directed by Engineer-in-charge. | 3 | Each | |
| 108 | 97 | M&L construction of valve pit of inner sizes 450 x 450 x 600mm with stone masonry construction on PCC 1:4:8 type D2 foundation concrete 15 cm thick complete with mild steel sheet cover 3 mm thick and angle iron frame of size 40 x 40 x 6mm fixed in 10 cm thide (1:3:6) type CI coping duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and including locking arrangement and lifting handle all as specified and shown on drawing. All internal surface and external surface upto 15 cm below normal ground level of stone masonry shall be plastered 15mm thick in cement mortar 1:4, finish fair and even including necessary excavation and earth work in any type of soil complete all as specified and as directed by Engineer-in-charge. | 3 | Each | |
| 109 | 98 | M&L construction of valve pit of inner sizes 1050 x 750 x 1000mm with stone masonry construction on PCC 1:4:8 type D2 foundation concrete 15 cm thick complete with mild steel sheet cover 3 mm thick and angle iron frame of size 40 x 40 x 6mm fixed in 10 cm thide (1:3:6) type CI coping duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and including locking arrangement and lifting handle all as specified and shown on drawing. All internal surface and external surface upto 15 cm below normal ground level of stone masonry shall be plastered 15mm thick in cement mortar 1:4, finish fair and even including necessary excavation and earth work in any type of soil complete all as specified and as directed by Engineer-in-charge. | 3 | Each | |
| 110 | 99 | Supply and fixing in replacement 40 mm bore gun metal gate valves with iron wheel head, screwed both ends for jointing iron pipe, non rising forged brass spindle class I complete all as specified and directed by Engineer -in-Charge. | 4 | Each | |
| 111 | 100 | Supply and fixing in replacement 25 mm bore gun metal gate valves with iron wheel head, screwed both ends for jointing iron pipe, non rising forged brass spindle class I complete all as specified and directed by Engineer -in-Charge. | 4 | Each | |
| 112 | 101 | Supply and fixing in replacement 20 mm bore gun metal gate valves with iron wheel head, screwed both ends for jointing iron pipe, non rising forged brass spindle class I complete all as specified and directed by Engineer -in-Charge. | 4 | Each | |
| 113 | 102 | Supply and fixing in replacement 100mm bore Non-return valve (CI Refluxe valve) flanged joint with bypass arrangement complete with nut, bolts and washers complete all as specified and directed by Engineer-in-charge. | 1 | Each | |
| 114 | 103 | Supply and fixing in repair 80mm bore Non-return valve (CI Refluxe valve) flanged joint with bypass arrangement complete with nut, bolts and washers complete all as specified and directed by Engineer-in-charge. | 1 | Each | |
| 115 | 104 | Supply and laying of 15 mm bore dia GI tubing, medium grade galavanised with all fittings and fixed to walls / celing / laid in floor suitable for pump suction pipe, connection, testing and commissioning, incld taking down / out of old u/s existing pipe complete all as specified and directed by Engineer-in-charge. | 60 | RM | |
| 116 | 105 | Supply and fixing in replacement of GI flanges suitables for 100mm bore pipe with bolt holes drilled at same pitch circle dia as per existing model incld rubber joints GI nut & bolts complete all as specified and directed by Engineer-in-charge. | 4 | Each | |
| 117 | 106 | All as per above tem no. 105.00 but suitable for 80 mm dia bore size. | 4 | Each | |
| 118 | 107 | Supply and fixing in repair of leather for 100 mm bore Foot valve complete with nut, bolts and washers complete all as specified and directed by Engineer-in-charge. | 4 | Each | |
| 119 | 108 | Supply and fixing in repair of leather for 80 mm bore Foot valve complete with nut, bolts and washers complete all as specified and directed by Engineer-in-charge. | 4 | Each |
AI Tender Summary
Tender Timeline
Jul 29, 2021
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 17, 2021
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Completed
Jul 27, 2021
18:00 IST
Corrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Completed
Jul 30, 2021
18:00 IST
Corrigendum-3 Issued
Clarifications on tender conditions and amendments issued.
CompletedJul 30, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 02, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
Completed