| 1 | 1 | Demolishing brick work manually/ by mechanical means including\nstacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar | | 32 | cum |
|---|
| 2 | 2 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): From brick work in cement mortar | | 8 | 1000 No.s |
|---|
| 3 | 3 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | | 11.5 | cum |
|---|
| 4 | 4 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | | 7 | cum |
|---|
| 5 | 5 | Salvage value of Bricks Considering 20% rate (Item No. 6.2.1) of the dismantling due to very old bricks and taking 50% bricks | | 16 | cum |
|---|
| 6 | 6 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. | | 35 | cum |
|---|
| 7 | 7 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.\nAll kinds of soil | | 61 | cum |
|---|
| 8 | 8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | | 20.5 | cum |
|---|
| 9 | 9 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | | 2.7 | cum |
|---|
| 10 | 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6( 1 cement:3 coarse sand:6 graded stone aggregate 40mm nominal size | | 0.9 | cum |
|---|
| 11 | 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) | | 4 | cum |
|---|
| 12 | 12 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). | | 6.1 | Sqm |
|---|
| 13 | 13 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight as per manufacturer's specification. | | 2 | per\n 50 kg\ncement |
|---|
| 14 | 14 | Making plinth protection 50mm thick of cement concrete 1:3:6(1cement:3 coarse sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth . | | 13.2 | Sqm |
|---|
| 15 | 15 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 c/sand : 3 graded stone aggregate 20mm. Nominal size). | | 8.3 | cum |
|---|
| 16 | 16 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). | | 1.72 | cum |
|---|
| 17 | 17 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up \nto floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). | | 6.3 | cum |
|---|
| 18 | 18 | Centring and suttering including strutting, propping etc. and removal of form for Foundations, footings bases of columns etc. for mass concrete. | | 31 | Sqm |
|---|
| 19 | 19 | Centring and suttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landing, balconies and access platform. | | 37 | Sqm |
|---|
| 20 | 20 | Centring and suttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers | | 47.5 | sqm |
|---|
| 21 | 21 | Centring and suttering including strutting, propping etc. and removal of form for Columns, pillars, posts and struts (square,\nrectangular or polygon in plan). | | 21 | sqm |
|---|
| 22 | 22 | Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more. | | 2638 | kg |
|---|
| 23 | 23 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | | 1 | each |
|---|
| 24 | 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) | | 14 | Cum |
|---|
| 25 | 25 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) | | 68 | sqm |
|---|
| 26 | 26 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood | | 0.6 | Cum |
|---|
| 27 | 27 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. Kiln seasoned and chemically treated hollock wood 35 mm thick shutters | | 18.3 | sqm |
|---|
| 28 | 28 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Kiln seasoned and chemically treated hollock wood | | 12.1 | sqm |
|---|
| 29 | 29 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes 4 mm thick glass pane (weight not less than 10 kg per sqm) | | 6.5 | sqm |
|---|
| 30 | 30 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). | | 6.5 | sqm |
|---|
| 31 | 31 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc | | 55.5 | Kg |
|---|
| 32 | 32 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm | | 8 | each |
|---|
| 33 | 33 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm | | 30 | Each |
|---|
| 34 | 34 | Providing and fixing bright finished brass handles with screws etc. complete: 125mm | | 16 | Each |
|---|
| 35 | 35 | Providing and fixing bright finished brass handles with screws etc. complete: 75mm | | 15 | Each |
|---|
| 36 | 36 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate | | 2.4 | sqm |
|---|
| 37 | 37 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. Marble tiles (polished) Raj Nagar 8 mm thick | | 3.6 | sqm |
|---|
| 38 | 38 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with Raj Nagar plain | | 6.2 | sqm |
|---|
| 39 | 39 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete | | 48.2 | sqm |
|---|
| 40 | 40 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | | 23.2 | sqm |
|---|
| 41 | 41 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter | | 8.5 | metre |
|---|
| 42 | 42 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm | | 12 | Each |
|---|
| 43 | 43 | 12mm cement plaster of mix: 1:4 (1 Cement:4 Coarse sand) | | 58 | Sqm |
|---|
| 44 | 44 | 15 mm cement plaster on rough side of single or half brick wallof mix: 1:4 (1 cement: 4 coarse sand) | | 68 | sqm |
|---|
| 45 | 45 | 15 mm cement plaster on rough side of single or half brick wa ll finished with a floating coat of neat cement of mix : 1:3 (1 cement: 3 fine sand) | | 38.5 | sqm |
|---|
| 46 | 46 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) | | 31 | sqm |
|---|
| 47 | 47 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer | | 89 | sqm |
|---|
| 48 | 48 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | | 63.15 | sqm |
|---|
| 49 | 49 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | | 153 | sqm |
|---|
| 50 | 50 | Lettering with black Japan paint of approved brand and manufacture. | | 250 | per letter per cm height |
|---|
| 51 | 51 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre | | 26.5 | Sqm |
|---|
| 52 | 52 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work | | 26.5 | Sqm |
|---|
| 53 | 53 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orissa pattern W.C. pan of size 580x440 mm | | 2 | Each |
|---|
| 54 | 54 | Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white | | 2 | Each |
|---|
| 55 | 55 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and\nfloors wherever required : W.C. pan with ISI marked white solid plastic seat and lid | | 1 | Each |
|---|
| 56 | 56 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. | | 3 | Each |
|---|
| 57 | 57 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern | | 1 | Each |
|---|
| 58 | 58 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 630x450 mm | | 2 | Each |
|---|
| 59 | 59 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia | | 2 | Each |
|---|
| 60 | 60 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | | 2 | Each |
|---|
| 61 | 61 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | | 2 | Each |
|---|
| 62 | 62 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms | | 2 | Each |
|---|
| 63 | 63 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. | | 2 | Each |
|---|
| 64 | 64 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms | | 7 | Each |
|---|
| 65 | 65 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia Pipes | | 14 | metre |
|---|
| 66 | 66 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes | | 16 | metre |
|---|
| 67 | 67 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes | | 8.5 | metre |
|---|
| 68 | 68 | Providing and fixing brass bib cock of approved quality : 15 mm | | 6 | Each |
|---|
| 69 | 69 | Providing and fixing brass stop cock of approved quality : 15 mm | | 10 | Each |
|---|
| 70 | 70 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) : 25 mm nominal bore | | 4 | Each |
|---|
| 71 | 71 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) : 32 mm nominal bore | | 2 | Each |
|---|
| 72 | 72 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm | | 2 | Each |
|---|
| 73 | 73 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank | | 2000 | per Litre |
|---|
| 74 | 74 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. | | 6 | each |
|---|
| 75 | 75 | Supplying and fixing C.I. Cover with frame (for manhole and chambers) 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg | | 1 | each |
|---|
| 76 | 76 | Providing and fixing UPVC soil, waste pipe including all requisite fittings, jointing of pipes & fittings with solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer- in Charge 75 mm dia | | 20.2 | metre |
|---|
| 77 | 77 | Providing and fixing UPVC soil, waste pipe including all requisite fittings, jointing of pipes & fittings with solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer- in Charge 110 mm dia | | 15.2 | metre |
|---|
| 78 | 78 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1.1 (GROUP B) | | 16 | Point |
|---|
| 79 | 79 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. - (20 mm Dia) | | 15 | Metre |
|---|
| 80 | 80 | Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. - (3 x 2.5 sqmm) | | 15 | Metre |
|---|
| 81 | 81 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. | | 2 | Each |
|---|
| 82 | 82 | Supplying and fixing 6 way, Double door , single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) | | 1 | Each |
|---|
| 83 | 83 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. | | 1 | Each |
|---|
| 84 | 84 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, SP miniature circuit breaker suitable for inductive load of single poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. | | 4 | Each |
|---|
| 85 | 85 | S/I/T/C of 18W LED tube light fitting of make Bajaj/Crompton/Havells, 1x18W (havells make) including all accessories,on wall/truss with round block, screw etc as required. | | 9 | Each |
|---|
| 86 | 86 | Supplying, installing, testing and commissioning of (pre-wired) bulk head fittings with glass complete containing WCFL/W GLS lamps per fitting, complete with all accessories including connection etc as required(havells, Bajaj, Phillips, Crompton)(10 watt) | | 4 | Each |
|---|
| 87 | 87 | Supplying of Outdoor aesthetically designed 25 watt LED Street Light Luminare with single piece die cast aluminium housing, (including driver) with IP rating of IP66, complete with internal wiring, with extremely precision designed heat sink suitable for top open for easy maintenance, complete with IP66 protection Class, with polycarbonate cover .The fixture should be suitable for pole / bracket mounting. | | 2 | Each |
|---|
| 88 | 88 | Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of all type of street light fitting on pole / wall / structure including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required. | | 2 | Each |
|---|
| 89 | 89 | Supplying and fixing out door type loop in loop out cable junction box (200 mm X 150 mm X100 mm)fabricated from 1.6 mm MS sheet enclosed wheather proof, dust proof, water proof and locking arrangement internally embedded gasket with bottom cable entry plat through cable glands. Seperate for incoming and out going cables and wires duly fitted with following in it.\nHD Connector for 10 to 16 sqmm - 4 Nos. \n6 amp SP 'C' curve 10 KA MCB - 1 No.\nfixing Clamps - 2 Nos.\n | | 2 | Each |
|---|
| 90 | 90 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32amps 240 volts “C” curve DP MCB complete with connections, testing and commissioning etc. as required. | | 1 | Each |
|---|
| 91 | 91 | Supplying, Installation, Testing and commissioining of 300mm dia sweep exhaust fan of approved make ALMONARD/CROMPTON GREAVES/Havells Heavy duty or any other equivalent make with 1400 RPM speed along with all other accessories i.e. louvers etc., and fixing the fan on the existing wall including connection etc as required. | | 3 | Each |
|---|
| 92 | 92 | Installation, testing and commissioning of pre-wired, all types lighting fittings, complete with all accessories and tube etc. directly on ceiling / wall / bracket, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing within fitting, within bracket & within loop box/point (Except conduit) etc. as required.\n | | 2 | Each |
|---|
| 93 | 93 | Wiring for circuit/ submain wiring alongwith earth wire with 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in GI Pipe as required. | | 10 | Metre |
|---|
| 94 | 94 | Supplying of XLPE insulated and PVC tape innersheated aluminium aluminium conductor armoured cable of 1.1 KV grade of following sizes confirming to IS:7098 (Part- I) 1988 with up to date ammendment as required. (Polycab, Finolex, Havells) 2x10 sqmm\n | | 45 | Metre |
|---|
| 95 | 95 | Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size up to 35 sqmm on wall / pole / steel structure surface as required. | | 38 | Metre |
|---|
| 96 | 96 | Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size up to 35 sqmm in ground including excavaation, sand cushioning , protective covering and refiling the trench etc as required | | 7 | Metre |
|---|
| 97 | 97 | Supplying and fixing of light class G.I. pipe of following size in mm dia. (nominal) 3 meter length along the pole for protection of under ground cable as required. -50 mm dia. (nominal) . | | 2 | Each |
|---|
| 98 | 98 | Supplying and making end termination with brass compression gland and aluminium lugs for FOLLOWINGsize of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.- 2 X10 sq. mm (19mm) \n | | 2 | Each |
|---|
| 99 | 99 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.\n | | 1 | Each |
|---|
| 100 | 100 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.\n | | 7 | Metre |
|---|
| 101 | 101 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.\n | | 8 | Metre |
|---|
