| 1 | 1 | Design, construction, testing and successfully commissioning of 0.14 MGD Rapid Sand Filtration Plant, with architectural features on “Turn-Key” basis for WSS Tenghar Payer (under JJM ).including construction of pre settling tank for 0.14 MGD filtration plant, Flash mixer ,Clarifloculator sludge disposal drain for construction of 0.24MGD Rapid Sand Filtration Plant ,connected with plant and allied structures including rotating bride with construction of canopy , center bearing , railing both sides of bridge , electric motor 2H.P reduction gear with coupling both sides including structural steel truss over rapid sand filter house with coloured C.G.I sheets including ridges , soffits whichever is required to cover the truss complete , construction of filter beds with filter media , grill inside the plant ,stair and around the filter beds , providing kota stone flooring , tiles for maduls and Alum bleaching chambers , including construction of aluminum doors , windows , shutters (frames with size 3.75x1.75 inches ) including glazing. All electrical /mechanical works with standard quality of sluice valves , bends , extension rods with tail pieces and C.I pedestals embedding in cement concrete, construction of disposal drain , providing fixing PVC pipes and lateral pipes with specials , M.S pipe with M.S flanged joints of standard quality , nuts , bolts , washers , cutting of threads etc . Air blower with standard quality of motors with wire , switches , switch boards , panel boards , control boards , starters with all necessary fittings whichever is required for completion of electric/mechanical works as per directions of Engineer-in-charge, painting inside the plant and outside with face lifting of plant disposal of surplus material leveling and dressing of ground | | 1 | Job |
|---|
| 2 | 2 | Design, construction, testing and successfully commissioning of RCC Over Head Tank 0.35 lac gallons capacity (shell type) with architectural features in single compartment with 20mtrs staging height (above ground up to ring beam ) on “Turn-Key” basis at for WSS N.C Naina (under JJM )including providing and fixing of B-Class 3 pipe lines of 100mm dia for supply main, washout and overflow line with sluice valves make of VOG/AVK and all necessary accessories such as lightening arrester, water level indicator, RCC stair from ground level to tank floor levels gallery along outside columns gallery to top of dome and inside the tank with side steel railing, ventilating cowls, main hole covers with frame and M.S. railing for stair and roof flooring vertical pipe lines and standard pipe fitting for supply main and washout, overflow with 12mm thick flanged joints etc all complete. The top water container should be preferable cylinder in shape, shaft for support shall not be permitted including disposal of excavated material from the premises, boulder filling inside the tank upto ground level, cement primer, water proofing outside the tank surface whichever is required for commissioning of structures with allied works complete including connecting to pipe line | | 1 | Job |
|---|
| 3 | 3 | Earth work in excavation by manual means in trenches for foundations ,drains, pipes, cables etc (not exceeding 1.5mtr in width) and for shafts ,wells ,cesspits, and the like not exceeding 10sqm on plan ,including dressing of sides and ramming of bottoms lift upto 1.5m, including getting out excavated earth and disposal of surplus excavated earth as directed All kinds of soils | | 3393.75 | Cum |
|---|
| 4 | 4 | Providing and laying of stone solling hand packed including watering dressing and ramming all complete | | 217.23 | Cum |
|---|
| 5 | 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size ) | | 66.19 | Cum |
|---|
| 6 | 6 | Providing and laying specified grade of reinforced cement concrete including curing but excluding the cost of centring , shuttering , finishing and reinforcement all works upto plinth level 1:2:4 mix ( 1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) | | 78.53 | Cum |
|---|
| 7 | 7 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 mix (1 cement :3 coarse sand :6 graded stone aggregate 20 mm nominal size ) | | 374.19 | Cum |
|---|
| 8 | 8 | Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete | | 43.42 | Sqm |
|---|
| 9 | 9 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand) | | 59.95 | Cum |
|---|
| 10 | 10 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level | | 59.95 | Cum |
|---|
| 11 | 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) | | 19.56 | Cum |
|---|
| 12 | 12 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Kiln seasoned and chemically treated hollock wood | | 1.17 | Cum |
|---|
| 13 | 13 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). Kiln seasoned & chemically treated hollock wood | | 34.24 | Sqm |
|---|
| 14 | 14 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Kiln seasoned and chemically treated hollock wood | | 26.44 | Sqm |
|---|
| 15 | 15 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc. | | 604.9 | Kg |
|---|
| 16 | 16 | Providing fixing of hinges of different sizes , haldarwazas, latches, handles , locking arrangement to main door , locks to doors of standard quality including screws , nuts nails , all sorts of carriage complete | | 1 | Job |
|---|
| 17 | 17 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover | | 6.76 | Sqm |
|---|
| 18 | 18 | Providing and fixing ball bearing for rolling shutters | | 2 | No |
|---|
| 19 | 19 | Steel reinforcement for RCC work including straightening, cutting , bending , placing in position and binding all complete upto plinth level thermo –Mechanically –Treated bars of grade Fe-500D or more | | 8391.9 | Kg |
|---|
| 20 | 19.1 | Centering shuttering including strutting , propping etc. and removal of form work for | | | |
|---|
| 21 | 19.2 | Foundation footings , bases for columns | | 1766.9 | Sqm |
|---|
| 22 | 19.3 | Lintel, beams, plinth beams, girders, bressumers and cantilevers. | | 55.14 | Sqm |
|---|
| 23 | 19.4 | Suspended floors, roofs, landings, balconies and access platforms | | 113.08 | Sqm |
|---|
| 24 | 19.5 | Edges of slabs and breaks in floors and walls Under 20 cm wide | | 71.66 | Mtr |
|---|
| 25 | 19.6 | Columns, pillars, piers, abutments, posts and struts. | | 15.12 | Sqm |
|---|
| 26 | 19.7 | Arches, domes, vaults upto 6 m span | | 44.83 | Sqm |
|---|
| 27 | 19.8 | Extra for arches, domes, vaults exceeding 6 m span | | 44.83 | Sqm |
|---|
| 28 | 19.9 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc | | 151.43 | Sqm |
|---|
| 29 | 20 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) | | 1927.78 | Sqm |
|---|
| 30 | 21 | Providing and fixing of sanitary items of standard quality like 1000 liters sintex , W.C Indian type , flush tank , with all accessories . pvc pipe , pipe specials , C.P items , p trap , floor trap, bends , steel sink , connecting with soakage , whichever be necessary to make functional all complete (to be paid as per actual details /measurements with supporting voucher dully verified by AEE concern ) | | 2 | Job |
|---|
| 31 | 22 | Provision for Construction of septic tank (12x8x6 of size ) with brick masonry in 1:3 mix including providing laying of RCC slab in 1:1.5:3 mix , with cement plaster of 1:3 mix including P Trps , bends , PVC prince-B class pipe ,disposal of excavated earth outside the premises , including M.S iron cover for man hole complete (to be paid as per actual details / measurements ) | | 1 | Job |
|---|
| 32 | 23 | Providing fixing supplying P.C.C rings including earthwork excavation and disposal of surplus excavated material outside the premises including providing and laying cement concrete in 1:2:4 mix over septic tank and soakage pit . construction of man hole chambers with angle iron frame and covering arrangements .providing fixing of P.V.C pipe ( prince make B class ) including bends whichever is required at site or as per directions of Engineer- in- charge (3 compartments for septic tank and 1 for soakage pit . (to be paid as per actual details /measurements ) | | 16.5 | Mtr |
|---|
| 33 | 24 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | | 60.6 | Sqm |
|---|
| 34 | 25 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick | | 516.25 | Sqm |
|---|
| 35 | 26 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter | | 62.49 | Sqm |
|---|
| 36 | 27 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work | | 1081.56 | Sqm |
|---|
| 37 | 28 | Providing ,supplying fixing instillation of electric fittings of standard quality incl. 19/18 copper wire cable connection with transformer , instillation of panel board, switch board, switches, lighting points, heating points, fans , exhaust fans pvc conduit, havels wire , MCB, changeover , whichever is related to the item and found necessary at site or as per directions of Engineer- in- charge (to be paid as per actual details /measurements with supporting vouchers dully verified by AEE concern ) | | 2 | Job |
|---|
| 38 | 29 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Welded | | 4037.5 | Kg |
|---|
| 39 | 30 | Providing corrugated G.S sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks , bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I filled with white lead , including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horiziontal / vertical or curved surface ) excluding the cost of purlins , rafters and trusses and including cutting to size and shape wherever required 0.63mm thick with zinc coating not less than 275gram/sqm | | 260.22 | Sqm |
|---|
| 40 | 31 | Providing and fixing plained eaves boarding. 250x32 mm (nominal size ) | | 43.3 | Mtr |
|---|
| 41 | 32 | Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete .with 0.63 mm thick with zinc coating not less than 275 gram/m2 | | 48.21 | Mtr |
|---|
| 42 | 33 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) | | 16.61 | Cum |
|---|
| 43 | 34 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) | | 24.25 | Cum |
|---|
| 44 | 35 | Reinforced cement concrete work in arches, archribs, domes, vaults shells, folded plate and roofs having slope more than 15° upto floor five level level including curing but excluding the cost of centering, shuttering finishing and reinforcement with: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) | | 4.48 | Cum |
|---|
| 45 | 36 | 12mm Cement plaster finished with a floating coat of neat cement of mix: (1 cement : 3 fine sand) | | 65.93 | Sqm |
|---|
| 46 | 37 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | | 4862.82 | Kg |
|---|
| 47 | 38 | Providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. (1 kg of water proofing material in 50 kg of cement) | | 80 | Kg |
|---|
| 48 | 39 | Providing fixing of tail pieces including cost of nuts, bolts, washers, welding complete | | 2 | No |
|---|
| 49 | 40 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) | | 15 | Cum |
|---|
| 50 | 41 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer incharge. Made of G.I. wire of dia 4 mm | | 549 | Sqm |
|---|
| 51 | 42 | Steel work welded in built up sections/framed work, including cutting, Hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | | 235 | Kg |
|---|
| 52 | 43 | Applying priming coats with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/ steel works | | 549 | Sqm |
|---|
| 53 | 44 | Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) | | | |
|---|
| 54 | 44.1 | 80 mm dia G.I pipes | | 1500 | Mtr |
|---|
| 55 | 44.2 | 50 mm dia G.I pipes | | 2000 | Mtr |
|---|
| 56 | 44.3 | 40 mm dia G.I pipes | | 2000 | Mtr |
|---|
| 57 | 44.4 | 25 mm dia G.I pipes | | 3000 | Mtr |
|---|
| 58 | 44.5 | 20 mm dia G.I pipes | | 4000 | Mtr |
|---|
| 59 | 44.6 | 15 mm dia G.I pipes | | 1956 | Mtr |
|---|
| 60 | 45 | Providing and laying S&S Centrifugally Cast (Spun)/ Ductile Iron Pipes conforming to IS : 8329 | | | |
|---|
| 61 | 45.1 | 100 mm dia Ductile Iron Class K - 7 Pipes | | 1800 | Mtr |
|---|
| 62 | 46 | Making connection of G.I distribution branch with G.I main of following size by providing and fixing tees, including cutting and threading the pipe etc complete | | | |
|---|
| 63 | 46.1 | (a) 25 to 40 mm nominal bore | | 28 | No |
|---|
| 64 | 46.2 | (b) Above 40 mm nominal bore | | 8 | No |
|---|
| 65 | 47 | Filling available excavated earth (Excl. rock) in trenches, plinth sides of foundation etc. layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead upto 50mtr and lift upto 1.5mtr | | 2621.43 | Cum |
|---|
| 66 | 48 | Providing fixing double flanges C.I sluice valves /NRV’s/Air valves of standard quality Kirlosker /vage make confirming to IS 780 of 1984 read with upto date amendments standard mark ISI make PN-1 including cost of nuts bolts IR cloth including all sorts of carriage upto site of work complete job including cost of pedestals and handles as required at site (to be paid as per actual details with supporting vouchers dully verified by AEE concern ) | | | |
|---|
| 67 | 48.1 | (a) 100mm sluice valve | | 4 | No |
|---|
| 68 | 48.2 | (b) 150mm sluice valve | | 1 | No |
|---|
| 69 | 48.3 | (c) NRV | | 3 | No |
|---|
| 70 | 48.4 | (d) Air valve | | 4 | No |
|---|
| 71 | 49 | Grouting of stone pitching using M-10 nominal mix concrete (max. size on aggregates; 20mm nominal) @ 3.65 cum per 100 sq m on horizontal/side slopes; complete including curing. | | 360 | Sqm |
|---|
| 72 | 50 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, Lead upto 50 meter and lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil : | | 1750 | Sqm |
|---|
| 73 | 51 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 ton capacity in stages to proper grade and camber, applying and booming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density. | | 350 | Cum |
|---|
| 74 | 52 | Supplying and stacking at site Graded crushed stone aggregate of size | | | |
|---|
| 75 | 52.1 | 63 mm to 45 mm | | 173.25 | Cum |
|---|
| 76 | 52.2 | 53 mm to 22.4 mm | | 173.25 | Cum |
|---|
| 77 | 53 | Supplying and stacking at site Graded crushed stone aggregate of size | | | |
|---|
| 78 | 53.1 | 13.2 mm nominal size (Type A) | | 23.62 | Cum |
|---|
| 79 | 53.2 | 11.2 mm nominal size (Type B) | | 34.13 | Cum |
|---|
| 80 | 54 | Supplying and stacking of crusher dust (as a binding material including spreading over surface and carriage complete job ) | | 10.5 | Cum |
|---|
| 81 | 55 | Carriage of WBM for 15km | | 255.87 | Cum |
|---|
| 82 | 56 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. | | 1000 | Sqm |
|---|
| 83 | 57 | Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment) | | 1080 | Cum |
|---|
| 84 | 58 | Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or/and good earth to be paid separately) | | 1080 | Cum |
|---|
| 85 | 59 | Provision for soil test dully vetted by Design Director Quality Control and Inspection Division Srinagar/ Jammu for the complete scheme including conducting complete necessary soil investigation/cube testing /pile testing (if required) at proposed site , as per parameters , specifications mentioned in the tender document (for detailed technical specifications refer the detailed ENIT) | | 1 | Job |
|---|
| 86 | 60 | Provision for face lifting of scheme including painting priming ,beautification of site whichever is required at site complete job | | 1 | Job |
|---|
| 87 | 61 | Carriage of material from source of site upto site of work by mechanical transport including loading unloading stacking at site complete | | | |
|---|
| 88 | 61.1 | Sand and Bajri avg lead 15km | | 875.33 | Cum |
|---|
| 89 | 61.2 | Cement and steel avg lead 15km | | 190.7 | M.T |
|---|
| 90 | 61.3 | Stone solling avg lead 15km | | 217.23 | Cum |
|---|
| 91 | 61.4 | Bricks avg lead 26km | | 28477 | No |
|---|
| 92 | 61.5 | Good earth avg lead 10km | | 1080 | Cum |
|---|
| 93 | 62 | 1st Stage \nSupply, Installation, Testing & Commissioning of horizontal pumping equipment (detailed specifications shown in Annexure C) | | 2 | Job |
|---|
| 94 | 63 | Supply, Installation, Testing & Commissioning of open well Submersible Pumping equipment For Raw water (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 95 | 64 | Fabrication, providing & fitting of 80 mm dia.(class-c) Flanged GI delivery/Rising main of standard length. The job includes the cost of 18 mm thick MS flanges and welding in two layers to make the flanged joint strong and leak proof. The delivery pipe is to be weld on both sides with flanges of standard size with Advani /Adore electrode (Advani Oerlikon make). The job includes all types of skilled labours, power supply diesel generator etc required for the job, with suitable size nuts bolts RI Cloth in the flanged joints of delivery pipes. The pipe is to be laid underground in trenches by cutting of hard soil as per site condition | | 170 | Mtr |
|---|
| 96 | 65 | Fabrication providing & fitting of split type MS Clamps 8mm thick,2.5” wide(dia.) and 2.5 feet long for lowering of column pipes and holding of pumping unit after lowering. The job includes the cost of required size of nuts and bolts . | | 2 | Job |
|---|
| 97 | 66 | Providing & fitting of 80 mm dia. 90 to120 degree bend/ offsets/reducer made of (class-B) GI pipe and flanged on both ends after cutting threaded portion to make it leak proof. The bend shall have two no. flanges 18 mm thick weld on both sides in two runs of welding. The job includes p/f of suitable size nuts, bolts, RI Cloth required for jointing, | | 5 | Job |
|---|
| 98 | 67 | Fabrication, Providing and fitting of washout arrangement to the rising main by way of P/F of 80 mm dia G.I flanged pipe length(c-class)-1mtr. Providing / Fitting of 80mm dia. G. I. Tee of equal sides duly flanged 16mm thick on all sides and Providing / Fitting of 80mm dia. G. I. bend flanged both sides with Flange thickness 12 mm welding in double layers to make leak proof joints. Nuts, bolts and rubber insertion washers required are also included in the job. | | 1 | Job |
|---|
| 99 | 68 | Fabrication, Providing and fitting of Y- Junction to the rising main by way of P/F of 80 mm dia G.I flanged pipe length(c-class)-of required length including Providing / Fitting of flanges 16mm thick on all three sides with welding in double layers to make leak proof joints. Nuts, bolts and rubber insertion washers required are also included in the job. The job includes P/F of 80 mm dia G.I flanged pipe length(c-class)-of required length for connecting delivery main of open well submersible pumping unit to the main rising main. | | 1 | Job |
|---|
| 100 | 69 | Fabrication / Erection of Channel iron column to act as support for resting of MS joist (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 101 | 70 | Providing/fitting of manual type chain pulley block (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 102 | 71 | Providing, Fitting of 80mm,PN 1.6/16, Ductile Iron double flanged, soft seated glandless gate/ sluice valve. (detailed specifications shown in Annexure C) | | 5 | Job |
|---|
| 103 | 72 | Providing, Fitting of 80 mm,PN 1.6/16, Ductile Iron double flanged, Slanted seat swing check valve( NRV). (detailed specifications shown in Annexure C) | | 4 | Job |
|---|
| 104 | 73 | Creation of 63 KVA Electric Sub Station (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 105 | 74 | Supply and installation of MS tubular poles of 9 mtrs long, shall be anti-corrosive painted. The pole shall conform to SP-33 of IS-2713. The job includes providing / laying of cement concrete in 1:2:4 cement, sand aggregate block for grouting of each pole. The pole shall be fitted / welded with 12 x 12 square inch size and 6mm thick MS plate at the bottom and having duly drilled holes at top at appropriate position for accommodating MS fasteners for holding crosses and safety devices and P/F of cross arms, insulators and appropriate size HT shackles/ eye bolts/D Cable holding clamps/ nuts & bolts for holding HT cable/conductor. Job includes the cost of black painting of poles up to a height to 1.50 mtrs and the top with a silver shade. Job includes spiral earthing also. | | 8 | Job |
|---|
| 106 | 75 | S/I/T/C of MS tubular poles 02 No. at substation of 9m height, 410 (SP33) conforming to IS 2713 (part 2) 1990 as per REC standard welded with 40X40 sq. inch in size & 4mm thick MS plate at the bottom & having dully drilled holes at various sections for accommodating MS fasteners for holding channels for fitting of GO link set assembly. The erection of poles is carried out by grouting the pole in a circular cement block of 450mm in diameter & of total height equal to 1500mm (1200mm below the ground level & 300 mm above the ground level). The job includes P/ laying of stone soling of 200mm thick followed by P/ laying of PCC in 1:2:4 mix up to height of 1500mm. The job includes P/F of 04 No. of ISMC 75mm of 9 feet long for isolation of GO link set through screwed fasteners. The job includes cost of painting of poles with 2 coats of red oxide paint including black painting up to height of 1.5 m from bottom & the top with silver shade as per REC standard. The job includes providing & fitting of 02 No. sign board indicating “ 11000 Volt Danger” in Red color. (Spiral earthing of HT poles having suitable number of turns as per the REC norms & anti climbing feature are included in the job) | | 1 | Job |
|---|
| 107 | 76 | P/F/T/C of 11 KVA GO link set ( 3 pieces) of reputed make as per REC standard including pipe of suitable length & diameter for its operation . The job includes earthing of link set handle as per REC norms included in the job. | | 1 | Job |
|---|
| 108 | 77 | Providing/ fitting of link rod for isolating link set. | | 1 | No |
|---|
| 109 | 78 | P/F of the sign plates fabricated out of MS sheets of size 1’x1’ to be fitted on each pole. The job includes letter writing in red colour displaying 11 KVA – DANGER. | | 8 | Job |
|---|
| 110 | 79 | P/F of .03ACSR AL conductor | | 60 | Mtr |
|---|
| 111 | 80 | Supply, installation of 35 mm Sq. 3 core ABC Al HT cable of 11 KV grade. Make: Havelis/L&T. Job includes its fitment on poles with HT holding clamps | | 320 | Mtr |
|---|
| 112 | 81 | P/F of 11 KV cable termination kit(set of three) for connecting ABC cable with the existing HT line and 63 KVA HT transformers. | | 6 | No |
|---|
| 113 | 82 | CONTROL PANEL\nFabrication providing and fitting of Modular control panel of Appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection class: IP 55 and fitted | | 2 | Job |
|---|
| 114 | 83 | Providing / Fitting of 35 mm Sq. 3.5 core, XLPE Armoured Al. Cable conforming to IS : 7089 part 1st as service line from the HT transformer to control panels through the change over arrangement for proper operation of both DG set and Power supply as per requirement including all thimbling crimping taping etc. (Havells/L&T/Finolex make)\nNOTE: - The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of dowel’s make and of appropriate size and connected by hydraulic crimp tool only. | | 50 | Mtr |
|---|
| 115 | 84 | Providing and Fitting of 10 sq. mm, 3 core flat submersible cable for interconnecting motor/ various electrical gadgets through proper system including thimbles of appropriate size including all thimbles crimping taping etc (L&T /RR/ Havell’s make) | | 150 | Mtr |
|---|
| 116 | 85 | Providing and Fitting of 16 sq. mm, single core copper cable for interconnecting motor/ various electrical gadgets through proper system including thimbles of appropriate size including all thimbles crimping taping etc (L&T/RR/ Havell’s make) | | 180 | Mtr |
|---|
| 117 | 86 | Providing, Installation, Testing & Commissioning 30 KVA voltage stabilizer (detailed specifications shown in Annexure C) | | 3 | Job |
|---|
| 118 | 87 | P/I of earthing station comprising of company fabricated earthing electrode as per IS : 3043 (detailed specifications shown in Annexure C) | | 3 | Job |
|---|
| 119 | 88 | Providing/ laying of 3mm thick high density anti skid rubber floor matting on the machine floor level area including the floor surface area around power control panels and other gadgets. The job includes cleaning of the floor and the under surface of the matting removing dust, dirt, grease and loose sand grains if any. Applying the adhesive of sufficiently high bonding strength both on the floor as well as on the under surface of the rubber matting for fixing. | | 100 | Sft |
|---|
| 120 | 89 | Fabrication and Providing of 6’ x 4’ size MS angle Iron Framed worker’s sleeping bed made out of ISA 50 mm x 50 mm x 6 mm. The job shall include four no of legs 2’ long made out of equal iron ISA 50 mm x 50 mm x 6 mm with braces of MS flats 50mm x 4 mm, 2 no(1’ Long) for each leg and for central support,3 no’s (5’ long each) to be welded precisely with Advani electrodes as per requirement. Job also includes P/F of 19 mm ply board of 6’ x 4’ size. | | 1 | Job |
|---|
| 121 | 90 | Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection (detailed specifications shown in Annexure C) | | 2 | Job |
|---|
| 122 | 91 | Electrification:-(detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 123 | 92 | Stage 2nd \nSupply, Installation, Testing & Commissioning of horizontal pumping equipment (detailed specifications shown in Annexure C) | | 2 | Job |
|---|
| 124 | 93 | Fabrication, providing & fitting of 80 mm dia.(class-c) Flanged GI delivery/Rising main of standard length. The job includes the cost of 18 mm thick MS flanges and welding in two layers to make the flanged joint strong and leak proof. The delivery pipe is to be weld on both sides with flanges of standard size with Advani /Adore electrode (Advani Oerlikon make). The job includes all types of skilled labours, power supply diesel generator etc required for the job, with suitable size nuts bolts RI Cloth in the flanged joints of delivery pipes. The pipe is to be laid underground in trenches by cutting of hard soil as per site condition | | 70 | Mtr |
|---|
| 125 | 94 | Providing & fitting of 80 mm dia. 90 to120 degree bend/ offsets/reducer made of (class-B) GI pipe and flanged on both ends after cutting threaded portion to make it leak proof. The bend shall have two no. flanges 18 mm thick weld on both sides in two runs of welding. The job includes p/f of suitable size nuts, bolts, RI Cloth required for jointing, | | 4 | Job |
|---|
| 126 | 95 | Fabrication, Providing and fitting of 80mm dia washout arrangement to the rising main by way of P/F of 80mm dia G.I flanged pipe length(c-class)-1mtr. Providing / Fitting of 100 mm dia. G. I. Tee of equal sides duly flanged 16mm thick on all sides and Providing / Fitting of mm dia. G. I. bend flanged both sides with Flange thickness 12 mm welding in double layers to make leak proof joints. Nuts, bolts and rubber insertion washers required are also included in the job. | | 1 | Job |
|---|
| 127 | 96 | Fabrication / Erection of Channel iron column to act as support for resting of MS joist -(detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 128 | 97 | Providing/fitting of manual type chain pulley block (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 129 | 98 | Providing, Fitting of 80mm,PN 1.6/16, Ductile Iron double flanged, soft seated glandless gate/ sluice valve (detailed specifications shown in Annexure C) | | 4 | Job |
|---|
| 130 | 99 | Providing, Fitting of 80 mm,PN 1.6/16, Ductile Iron double flanged, Slanted seat swing check valve( NRV). (detailed specifications shown in Annexure C) | | 3 | Job |
|---|
| 131 | 100 | CONTROL PANEL\nFabrication providing and fitting of Modular control panel of Appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection class: IP 55 and fitted | | 2 | Job |
|---|
| 132 | 101 | Providing / Fitting of 35 mm Sq. 3.5 core, XLPE Armoured Al. Cable conforming to IS : 7089 part 1st as service line from the HT transformer to control panels through the change over arrangement for proper operation of both DG set and Power supply as per requirement including all thimbling crimping taping etc.L&T/ Havells make. NOTE: - The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of dowel’s make and of appropriate size and connected by hydraulic crimp tool only. | | 120 | Mtr |
|---|
| 133 | 102 | Providing and Fitting of 16 sq. mm, single core copper cable for interconnecting motor/ various electrical gadgets through proper system including thimbles of appropriate size including all thimbles crimping taping etc (L&T/RR/ Havell’s make) | | 180 | Mtr |
|---|
| 134 | 103 | Providing, Installation, Testing & Commissioning 30 KVA voltage stabilizer (detailed specifications shown in Annexure C) | | 2 | Job |
|---|
| 135 | 104 | Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) (detailed specifications shown in Annexure C) | | 2 | Job |
|---|
| 136 | 105 | S/I/T/C of 100 KVA, 3 phase and neutral HT Transformer (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 137 | 106 | Providing, installation, testing and commissioning of ‘Silent type Air cooled” Diesel Generating of 40 KVA Rating and 3 Phase (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 138 | 107 | Civil Works: DG set Foundation block (10’ x 6’)\nEarthwork excavation work in all kinds of soil in ordinary rock in trenches \n10´×6´×6`` = 30 cft=0.84 cum | | 0.84 | Cum |
|---|
| 139 | 108 | Providing and laying of dry stone soiling hand packed\n10×6´×6`` = 30 cft=0.84 cum | | 0.84 | Cum |
|---|
| 140 | 109 | Providing and laying of in position specified grade of cement concrete in 1;3;6 mix\n10×6´×8’ = 480 cft=13.58cum\n60% of concrete =8.14cum@4949/cum\n40 % of plum=5.44cum @550/cum | | 1 | Job |
|---|
| 141 | 110 | Cantering & shuttering including strutting propping& removal of form work of foundation & walls\n10’x8’x2+ 6’x8’x2 =256 sft =23.79Sq m | | 23.79 | Sqm |
|---|
| 142 | 111 | Providing and laying of cement plaster 1 inch thick in 1:4 mix\n10’x8’x2+6’x8’x2+10x6=316sft=29.37sq m | | 29.37 | Sqm |
|---|
| 143 | 112 | Extra carriage of material from dumping site to work site by manual labour with an average lead of 300 m of overall material involved at site in lump sum | | 1 | Job |
|---|
| 144 | 113 | Providing of tool kit consist (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 145 | 114 | Providing/fitting of thermo cool 12mm thick along with jute matting/excel for the operator’s room and having size of 12x12 Sq.feet . The job also includes providing of 2no.cushions. | | 1 | Job |
|---|
| 146 | 115 | Providing of two No Quilts with cotton cover, two No. Mattress with cotton covers, two NO sleeping bed sheets, two No pillows with covers, two NO Blankets for the employees in the operators room working during night shift & includes chargeable battery of Philips/any other reputed make of Lantern type 4 No. Plastic chairs & one plastic table The material shall be supplied at the site. | | 1 | Job |
|---|
| 147 | 116 | Providing/fitting of aluminium /GI cable tray of suitable size width not less than 4 inch, to accommodate cables & wiring inside operators quarter & machine room. Job includes P/F of all types of accessories & fixtures nuts & bolts & angle holders etc. | | 60 | Mtr |
|---|
| 148 | 117 | P/F of Al thimbles 25 Sq.mm ( 20 Nos)\nP/F of Al Thimbles 35 Sq.mm ( 15 Nos)\nP/F of Cu Thimbles 25 Sq.mm ( 20 Nos)\nP/F of Cu Thinbles 35 Sq.mm ( 15 Nos)\nP/F of Tap rolles at necessary terminations ( 15 Nos) | | 1 | Job |
|---|
| 149 | 118 | Providing of Sintex make 500 Ltrs Capacity Tank to be kept at site in the premises close to the pump station for safety purposes complete with 2 No. of Buckets 20 Lts capacity of Simrudi make for FIRE SAFETY. | | 1 | No |
|---|
| 150 | 119 | Providing of HT safety hand Gloves. | | 2 | Pair |
|---|
| 151 | 120 | Facilitiies for Operational Staff (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 152 | 121 | Providing of heating Blower of reputed make | | 2 | No |
|---|
| 153 | 122 | Providing of Cooking utensils (detailed specifications shown in Annexure C) | | 1 | Job |
|---|
| 154 | 123 | Providing/fitting of 1 H.P single phase horizontal self priming pumping unit of Kirloskar/Crompton make to act as priming pump for the main pumping units. The job including Providing/fitting of G.I pipes/fittings/valves for complete priming water circuit. The Job shall include P/F of DOL starter, wiring and other electrical items required for complete commissioning of priming unit. | | 2 | Job |
|---|
