Tender For Boq For Furniture For Boi, Aundh Baner Branch 1 Facade of Entrance Door- Refer Dwg.no.11 Providing and fixing in position Aluminium composite panel Boxing with PVDF coating & LDPE core laminated Eurobond / Altobond/ Alukbond Exterior Grade 4 mm thick with composite of (0.5mm-3mm-0.5mm) including fabrication for the same with aluminium sections, required hardware, silicon sealent (Dow Corning 789) masking tape, necessary scaffolding etc. as detailed in drawing no.(11) complete in all respects. 2 False Ceiling (Armstrong) Providing & fixing in position false ceiling in Armstrong 600 x 600 mm x 15/16 mm Dune Supreme RH 99 Prima tile with Butt edge framework as specified by Armstrong Co. with suspenders wherever required. Making necessary framework for A.C. ducting, if any, and necessary cutouts for diffusers and light fittings, taping and finishing to proper line & level, including making grooves and trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1” x 1” for edges including finishing with White Plastic Emulsion Paint etc. complete in all respects. (Note:- Only the plan area will be measured for payment. No extra payment will be made for cutouts, grooves, mouldings etc.) 3 False Ceiling (Gypsum Board) Providing & fixing in position false ceiling in Gypboard 12mm thick for horizontals & verticals fixed over G.I. framework as specified by India Gypsm Co. Ltd. including trap doors for A.C unit in 18mm thick M.R. Grade Plywood with Stainless Steel hinges & locks with moulding 1” x 1” for edges including finishing with White Plastic Emulsion Paint etc. complete in all respects. (Note:- Only the plan area will be measured for payment. No extra payment will be made for cutouts, grooves, mouldings etc. ) 4 Entrance Door Providing and fixing Entrance Door (glazed) as per drawing no.11 in Silver Anodised aluminium door section (Jindal make) in top and bottom, glazed with 12 mm thick glass of approved make with etching and frosting. Item to include floor springs, lock, all necessary hardware of Stainless Steel finish as approved by the Project Consultant/ Bank complete in all respects. 5 Front Office Counter: Providing and fixing in position Front Office Counter 2’-6” wide as per drawing No.(1-A, 1-B, 1-C , 1-D ) comprising of the following complete in all respects:- i) Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x1” T.W. beading patti with melamine finish. ii)Vertical facia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades. iii)Vertical drop (horizontal band) shall be provided on the facia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shades of laminate. iv) Glazed partition above working top to be provided with 12mm thick clear glass cut to the standard shape fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish. v) 3’-10” high Boxing (10”x10”) made with 18 mm thick plywood finished with 1 mm thick laminate including providing and fixing 6 mm thick square frosted glass at a height 3’-2” above finished floor level. vi) 1’-9” high Boxing (5”x5”) made with 12 mm thick plywood finished with 1 mm thick laminate. vii) vertical supports made with 18 mm thick plywood finished with white enamel paint. viii) CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. ix) Footrest made with T.W. member of size 4”X1 ½ “ finished with french polish. x) Drawer units as per drawing shall be provided with multipurpose Godrej locks in Each drawer. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. xi) Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting. The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the front. Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beadings with melamine polish for fixing the glass are to be provided. 6 Cash Counter: Providing and fixing in position Cash Counter 2’-9” wide as per drawing No.(2-A, 2-B, 2-C, 2-D, 2-E, 2-F) comprising of the following : i)Working top made with 25mm thick plywood finished with 1mm thick laminate. Outside edge of the working top shall be provided with 1¼”X1” Teak Wood moulding finished with melamine polish. Inside edge will be provided with ½ “x1” T.W. beading patti with melamine polish. ii)Vertical facia (Apron) made with 18mm thick plywood finished with 1mm thick laminate with 1mm thick groove at the joint of laminates of two different shades. iii)Vertical drop (horizontal band) shall be provided on the facia below the working top made with 18mm thick plywood finished with 1mm thick laminate with provision for concealed light, 1 mm thick groove shall be provided at the joint of two different shades of laminate. iv)Glazed partition of 1’-4” height above working top provided with 12mm thick toughened and frosted glass besides non-transparent film from inside fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. The exposed edges of the glass shall be finished in mirror polish. v)Transaction top shall be provided with 12mm thick toughened glass (partly glazed partly frosted) fixed horizontally with concealed Stainless Steel D bracket. Both exposed edges (inside and outside) shall be moulded and finished in mirror polish. vi)Glazed partition having height 1’.0” above the transaction top (in facia) shall be provided with 12 mm thick glass (clear) with cut out of 8”x 4” as per drawing. The edges of cut out and the top edge of glass are to be mirror polished and to be fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. vii)Glazed partition provided with 12mm thick glass (Clear) above the slit to be fixed to partition as per fixing details and to boxing with concealed S. S. finished ‘D’ brackets as shown in the drawing. . The exposed edges shall be finished in mirror polish. viii) 7’-7” high Boxing (10”x 10”) made with 18mm thick plywood as per drawing with 1-6” horizontal extension at the top including providing and fixing 6 mm thick square frosted glass at a height of 5”-11” above Finished Floor level. ix) 1’-9” high boxing (5”x 5”) made with 12 mm thick plywood finished with 1 mm thick laminate are to be provided. x) CPU Stand/ ready made Keyboard tray shall be provided of approved model and make. xi) Footrest made with T.W. member of size 4”X1 ½ “ finished with french polish. xii) Drawer units as per drawing shall be provided and each drawer should have vertical partitions for keeping the currency notes and multipurpose Godrej locks. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. xi) Boxing as per drawing made with 12mm thick plywood finished with Synthetic enamel paint shall be provided below the table top for electrical conduiting and at the bottom for the LAN cabling/Telephone wire conduiting. The item to include all necessary hardware and fittings in Stainless Steel finish, lipping to all edges and making provision only for electrical fitting behind the Vertical drop and also in the 10”x10” boxing as shown in the drawing. Necessary beadings with matching melamine polish for fixing the glass are to be provided as per drawing/ as directed. 7 Solid Full Height Partition Providing & fixing in position solid Full Height Partition in frame work including door in 2’x 2’ grid (horizontally and vertically) comprising of 2”x 2” Salwood/RMT Section with 6 mm thick plywood on both sides finished with 1 mm thick laminates of approved make and colour Item to include 2” x 2” T.W. member for door frame. 35 mm thk water proof flush door and 8mm glass for door. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. (Note: In case of false ceiling, the vertical RMT members to be fixed with pucca ceiling but the area of partition payable will be below the false ceiling only). 8 Partly Glazed Full Height Partition Providing and fixing in position partly glazed Full Height Partition work as shown in the drawing nos. (4) including door as shown in the drawing No.(13) in 2’x 2’ grid (horizontally and vertically) comprising of 2”x 2” Salwood/RMT Section with 6 mm thick plywood on both sides finished with 1 mm thick laminates of approved make and colour Item to include 2” x 2” T.W. member for door frame as per shown in the drawings both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings. Item to include 8 mm thick glass with etching and frosting as per design and 35 mm thk water proof flush door for door and 8 mm thick glass with etching and frosting. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. (Note: In case of false ceiling, the vertical T.W. members to be fixed with pucca ceiling but the area of partition payable will be below the false ceiling only). 9 Partly Glazed Partition for Cash Cabins Providing and fixing in position 7’-7” high partly glazed partition for Cash Cabins as per drawing nos. (2-A, 2-B, 2-C, 2-D & 2-E) including door in 2’x 2’ grid (horizontally and vertically) comprising of 2”x 2” Salwood/RMT Section with 6 mm thick plywood on both sides finished with 1 mm thick laminates of approved make and colour Item to include 2” x 2” T.W. member for door frame as per shown in the drawings both sides finished with 1 mm thick laminates of approved shade and colour as shown in drawings. Item to include 8 mm thick glass with etching and frosting as per design and water proof flush door 35mm for door and 8 mm thick glass with etching and frosting. The doors are also to be provided with Godrej Night Latch. Two wooden trays are also to be provided as per drawing. Necessary cutouts are to provided in the glass and the edges of the glass cutouts are to be finished in mirror polish. All exposed T.W. surfaces to be finished in melamine polish of matching laminate colour as directed including all necessary Stainless Steel finish fittings/ hardware, door closers, Godrej locks and wood preservative paint etc. as per list of approved material and as approved by the Project Consultant/ Bank complete in all respects. 10 Partly Glazed Low Height Partition Providing and fixing in position partly glazed low height partition (21/2” thick) in frame work with T.W vertical members at 2’ c/c and 3 horizontal members at equal distance comprising of 2”x 2” Salwood/RMT Section with 6 mm plywood on both sides finished with 1 mm thick laminates of approved make and shade as shown in drawing no.(14) or (3). Item to include 12 mm thick glass (clear/frosted) to be fixed as shown in drawing. The exposed edges of the glass to be finished in mirror polish. T.W runner should be melamine polished in matching colour of laminate etc complete in all respects. 11 Manager’s Table/Officer’s Table Providing and fixing in position Manager’s Table of size 5-6x 2-6 as per drawing no.(6) by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. CPU Stand/ ready made Keyboard tray shall be provided of approved model and make.Footrest made with T.W. member of size 4 x 1 ½ finished with french polish. Drawer units as per drawing shall be provided with multipurpose Godrej locks in each drawer. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1 x 1/4 T.W.lipping. All exposed T.W. sections to be melamined and internal surfaces to have white enamel paint as directed. Item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects. 12 Staff Table Providing and fixing in position Staff Table of size 5x 23 as above by using 25mm thick plywood for top and 18 mm thick plywood for all other horizontal and vertical members. CPU Stand/ ready made Keyboard tray shall be provided. Drawer units as per drawing shall be provided with multipurpose Godrej locks in each drawer. Facia of drawer unit shall be finished with 1mm thick laminate and all other sides shall be finished with white enamel paint. The drawers will be provided with handles (Stainless Steel finish) and channels as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. laminate of approved make & shade, and all exposed edges of table top & ply verticals to have 1 x 1/4 T.W.lipping. All exposed T.W. sections to be melamined and internal surfaces to have white enamel paint as directed. The item to include plywood boxing, all necessary hardware and fittings in Stainless Steel finish, lipping to all edges etc. complete in all respects. 13 Cash Counting Table Same as staff table but without storage. Size 26 x 19 25 mm thk top,19 mm ply boxing and 6 mm back. 14 Full height Storage / Low Height Storage/ Back Storage(Credenza) Providing and fixing in position Full height Storage / Low Height Storage/ Back Storage(Credenza) as shown in Drg. No.(8), (9) respectively using Plywood of required thickness finished with 1mm thick laminates as shown in the drawing and all other sides shall be finished with white enamel paint as detailed therein. The Storage Units shall be provided with handles (Stainless Steel finish) as per approval of the Project Consultant / Bank. All exposed plywood surfaces to be finished with 1mm thk. laminate of approved make & shade and all exposed edges of plywood to have 1 x 1/4 T.W.lipping. All exposed T.W. sections to be melamined in matching colour laminate and internal surfaces to have white enamel paint as directed. Item to include all necessary hardware and fittings in Stainless Steel finish, Godrej multi purpose locks including magnetic ball catcher etc., complete in all respects. All shutters should be locked if required at no extra cost. 15 Electrical Cupbaord Same as storage but with teak wood louvers for the shutters. 16 Column panelling Providing & fixing paneling made out of 2” x 1.5”salwood frame work at 1’6” to 2’ c/c in both ways, with 12 mm thk. ply and 1mm thk. lamination on top , etc. complete as per design. 17 Paint finish panelling for AC Same as panelling but finished with two coates of plastic emulsion paint. 18 Venetian blinds Providing and fixing vertical venetion blinds as per the design with top grid rails including best quality of fabric approved by the architect. 19 Rolling shutter cover Providing and fixing rolling shutter cover for branch and ATM in 19 mm ply finished with ACP claddind as specified in item no. 1 20 E Lobby panelling Providinfg and fixing ACP panelling for E-Lobby in 2/3 shades as per design and specifications of Architect, and material as per item no.1 21 Glass partitions in E Lobby Providing and fixing Dividing glass partitions 12 mm thk. toughened with corner rounding 3 including all necessary fitting hardware. 22 Slip writing desk Providing & fixing slip writing desk made out of 19mm thk ply. With 1mm thk laminate with 12 mm thk glass on top & verticals to make shelves for slips, etc. complete as per design & detail. 23 Suggestion box Providing & fixing suggestin box in 12 mm acrylic finish with shutter including lock etc complete. 24 Cheque drop box Providing & fixing Cheque drop box in 12 mm acrylic finish with shutter including lock etc complete. 25 Soft Board Providing and fixing soft board covered with approved coloured cloth on 12mm ply as base and 2x1 tw frame finished with 1mm thk. laminate & polish etc. complete. 26 Glass Film Providing and fixing imported PVC glass film 50 micron to glass as per design selected by the architect. 27 Mirror with frame and fitting
