Tender For Addition / Alteration Of Mi Room At Hmi Darjeeling
Tender Value
Ref. Documents
Estimated cost
Bid Submission
18 Jun 2021
0 days left
EMD
28000
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
HMI DARJEELING → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition / Alteration Of Mi Room At Hmi Darjeeling
BOQ
| Name of Work: ADDITION /ALTERATION TO MI ROOM AT HMI DARJELEING | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Supply fabricating and fixing of aluminium door powder coated of extrusion aluminium section including frame work complete, consisting of frame vertical and horizontal members, of size 104mmx44.45mmx1.8mm thick. Vertical style of door shutter of size 85mmx44.45mmx1.8mm thick. Top, middle and bottom rial of size 85mmx44.45x1.8mm thick and fixing 5 mm thick plain/tinted sheet glass of Modi guard/Atul or prelaminated particle board 9 to 10mm thick of make Kit Ply with aluminium bedding and rubber gasket/beading including frosted film as desired fixing of hydraulic floor spring one in single leaf or two nos in double leaf door of Make Sandhu/Kelvin/Evershine. One mortice lock for aluminium door (each) and two aluminium tower bolts for each door. Fixed with rawl plug including rectification of floor/wall to match the existing surfaces. All as specified and as directed by Engineer-in-Charge at site. (Cost of sheet glass/frosted film & sun control film shall be included in the unit of this item) | 6 | Sqm | |
| 2 | 2 | S&F for powder coated aluminium window three track sliding type with frames including 5mm thick tinted glass, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm fixed with standard rubber gasket, aluminium beadings and joining cleat for fixing including locking devices complete all as specified. Make : Jindal aluminium sections Nos. 20671, 20672, 20690 & 20668 | 30 | Sqm | |
| 3 | 3 | S&F powder coated aluminium window and ventilator shutters including frame work, fixed type without sash bar including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, 4 mm thick glass panes selected quality etc complete all as specified and as directed. | 8 | Sqm | |
| 4 | 4 | M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as directed by Campus Supdt. | 35 | Sqm | |
| 5 | 5 | M&L for screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:6 for laying of floor tiles as dierected. | 35 | Sqm | |
| 6 | 6 | M&L for 10 mm thick plaster in cement mortar 1 : 4 as a backing coat for fixing of wall tiles complete all as specified. | 50 | Sqm | |
| 7 | 7 | M&L for joint free light shade vitrified tiles 10 mm thick (square / rectangular) polished area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete. Make -Somany/Johnson/Orient | 25 | Sqm | |
| 8 | 8 | M&L for joint free Dark shade vitrified tiles 10 mm thick (square / rectangular) polished area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete. Make -Somany/Johnson/Orient | 10 | Sqm | |
| 9 | 9 | All as per items No 7 above but in vertical surfaces complete all as directed. | 50 | Sqm | |
| 10 | 10 | Taking down shutters exceeding 1 Sqm and not exceeding 2 Sqm each and refixing in same opening complete all as directed. | 3 | Each | |
| 11 | 11 | M&L for fixing of designer/decorative veneer sheet of size 1.5 to 2 mm thick on shutter with adhesive including removing of existing veneer complete all as specified and as directed. | 70 | Sqft | |
| 12 | 12 | M&L for preparation of old painted surfaces and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and as directed. | 20 | Sqm | |
| 13 | 13 | WALL PANELLING SCOPE OF WORK\n(i) Material and labour second class softwood plain fillets square rectangular/triangular section clean sawn and fixed with nails to existing wall of 30 cm centre to centre vertically and horizontally scantling required exceeding 13 sqcm but not exceeding 25 sqcm all as specified and directed.\n(ii) Material and labour 6mm thick plywood grade BWR, type BB fixed with nails to timber framework all as specified and directed.\n(iii) Fixing 3mm thick one side decorative veneered sheets with fevical over 6mm thick plywood with fixing of wooden beading for setting of veneered sheet. (Beading should be removed before polish)\n(iv) fixing of 2nd class softwood decorative beading to veneered for door/window jambs and cills and ceiling top where required. \n(v) Preparation of previously untreated veneered surfaces of any description over 10cm width or girth, applying one coat of colour mix putty over veneered nails, after drying of putty remove the putty by sand paper and finishing coat with PU finish with spary over two coat of sealer under coating complete all as specified. | 1100 | Sqft | |
| 14 | 14 | Ditto all as per specified in Ser No 13 above but fixing 19mm thick plywood grade BWR type BB fixed with nails to timber framework of sectional area not less than 50sqcm to existing wall 30cm centre to centre. | 810 | Sqft | |
| 15 | 15 | S & F designer venitian blinds vertical type 100mm wide slats made out of fabric cloth of approved shade fixed as per the instructions of manufacturers and all as specified by Campus Supdt. Make: Hanterdagluas/ Vista select/neha printed and exclusive shades. | 30 | Sqm | |
| 16 | 16 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) completete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, lights fitting etc remiving materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floor etc | 20 | Per Point | |
| 17 | 17 | Material and labour for point wiring with 1.5 Sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 volts drawn through and including rigid non metallic surface conduit medium grade ISI marked minimum 20mm dia and its accessories complete alongwith 1.5 Sqmm cable but in green colour as continuous earthing wire and connnecting to common earth duy completely concealed. Surface in walls/ceiling roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations, fan regulators etc, as required with 3mm thick plastic laminated sheet top cover all as specified and directed for the following points. | |||
| 18 | 18 | (a) One light point controlled by one modular switch | 20 | Point | |
| 19 | 19 | (b) One three pin modular socket out let 5 Amp on independents board complete | 6 | Point | |
| 20 | 20 | Supply and fix modular switch 1 way 6 Amp, 240 Volt. Make : Anchor/Havells | 20 | Each | |
| 21 | 21 | Supply and fix modular switch 1 way 16 Amp, 240 Volt. Make : Anchor/Havells | 2 | Each | |
| 22 | 22 | Supply and fix round type LED 15 watt for ceiling light complete set all as directed. Make - Havells | 20 | Each | |
| 23 | 23 | Supply and installation of hospital 3 seater stainless steel waiting chair as per sample and complete all as directed. | 6 | Set | |
| 24 | 24 | Supply and fixing of Acrylic Medical LED Signage Board at outer wall surfaces complete all as specified and as directed by the Principal. | 1 | Job |
AI Tender Summary
Tender Timeline
May 28, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedJun 18, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 21, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender