| 1 | 0 | Note : All unserviceable materials obtained out of demolition/dismantling/taking down (other than those for which credit catered under Schedule of credit) shall be disposed of outside MoD Land. Quoted rates against respective item shall deemed to include for same. | | | |
|---|
| 2 | 1 | Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material complete all as specified directed. | | 11 | Cubic\nMetre |
|---|
| 3 | 2 | Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed. | | 17.4 | Cubic\nMetre |
|---|
| 4 | 3 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position not otherwise specifically provided for and removal all rubbish material complete all as directed. | | 0.3 | Cubic\nMetre |
|---|
| 5 | 4 | Dismantling timber scantlings 40 Sqcm and over in section, in any position complete all as directed. | | 0.2 | Cubic\nMetre |
|---|
| 6 | 5 | Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as specified and directed. | | 10 | EACH |
|---|
| 7 | 6 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. | | 325 | Square Metre |
|---|
| 8 | 7 | Dismantling of stone slabs and tiles in flooring, apron etc of any description or thickness laid, bedded and pointed in any mortar complete all as directed. | | 1 | Ten Square Metre |
|---|
| 9 | 8 | Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed. | | 95 | Square Metre |
|---|
| 10 | 9 | Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :- | | | |
|---|
| 11 | 9.1 | 15mm bore. | | 95 | Running\nMetre |
|---|
| 12 | 10 | Dismantling of PVC(SWR) drain pipe alongwith fittings and accessories and taking out from walls, floors or from trenches, if required complete all as specified and directed for following sizes:- \n(Note :- The length shall be measured along the centre line including fittings and accessoires}. | | | |
|---|
| 13 | 10.1 | 75mm bore. | | 20 | Running\nMetre |
|---|
| 14 | 11 | Demolition and breaking up drain pipes (salt glazed stone ware, AC or reinforced concrete) set in cement mortar including PCC bedding and haunching etc complete all as specified and directed for following sizes:- \n(Note :- The length shall be measured along the centre line including fittings and accessoires}. | | | |
|---|
| 15 | 11.1 | 300mm bore. | | 16 | Running\nMetre |
|---|
| 16 | 12 | Excavation in post holes (or similar holes) in soft/loose soil, each n.exc 0.5 cum, getting out, returning, filling in and ramming moorum or broken rubble mixed with moorum in layers n.exc 25cm around foundation concrete as ordered, watering and removing surplus soil to a distance not exceeding 50 m and making good surface, complete all as specified and directed. | | 8 | EACH |
|---|
| 17 | 13 | M&L for hard core of broken stone or boulders of gauge n.exc 63 mm, deposited, spread & levelled in layers n.exc 15 cm thick watered & rammed to true surface complete all as specified and directed. | | 1.6 | Cubic\nMetre |
|---|
| 18 | 14 | M & L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. | | 1.5 | Cubic\nMetre |
|---|
| 19 | 15 | M & L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. | | 1 | Cubic\nMetre |
|---|
| 20 | 16 | M & L for PCC 1:5:10 type E-2 using 40 mm graded crushed stone aggregate as in foundation, filling under floor, sub base, in sunken floors etc complete all as specified and directed. | | 7 | Cubic\nMetre |
|---|
| 21 | 17 | M&L for providing precast cement concrete type A-1, 1:1.5:3 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and directed. | | 0.3 | Cubic\nMetre |
|---|
| 22 | 18 | M & L for precast cement concrete type C-1, 1:3:6 using 20mm graded aggregate as in bond stones set and jointed in cement mortar 1:6 complete all as specified and as directed. | | 19 | Cubic\nMetre |
|---|
| 23 | 19 | M & L for cutting holes into or through stone walls built in cement mortar and making good in cement concrete 1:2:4 type B-1 as required superficial area not exc 150 sqcm complete all as directed. | | 1120 | Per Centimetre of depth |
|---|
| 24 | 20 | Supply only integral water proofing compound ISI marked as approved complete all as specified and directed. | | 10 | Killo Gram |
|---|
| 25 | 21 | M & L for Use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for fair finished surfaces of concrete complete all as specified and directed. | | 6 | Square Metre |
|---|
| 26 | 22 | M & L for second class hardwood wrought as in scantling framed and fixed complete all as specified and directed. | | 0.2 | Cubic\nMetre |
|---|
| 27 | 23 | M & L for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. | | 0.2 | Cubic\nMetre |
|---|
| 28 | 24 | S & F 30mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etcwith plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8, clause 8.24 (b) and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.\n(Note :- S & F Glass/gauge shall be measured and paid for separately) | | 9 | Square Metre |
|---|
| 29 | 25 | S & F for 30mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete and size of member of shutters as specified in SSR Part-I (2009) section 8 all complete all as specified and directed. | | 8 | Square Metre |
|---|
| 30 | 26 | S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, In opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010). | | 29 | Running\nMetre |
|---|
| 31 | 27 | S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II. | | 10 | Square Metre |
|---|
| 32 | 28 | Taking down shutter of any description exc 1.0 sqm but n.exc 2.0 sqm each, easing and adjusting, refixing builders hardware including removal of unserviceable screws and refixing in same opening complete all as directed. | | 18 | Each \nLeaf |
|---|
| 33 | 29 | S & F butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed for following sizes:- | | | |
|---|
| 34 | 29.1 | 75mm long. | | 12 | EACH |
|---|
| 35 | 29.2 | 100mm long. | | 30 | EACH |
|---|
| 36 | 30 | S & F aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed for following sizes:- | | | |
|---|
| 37 | 30.1 | 150mm long. | | 12 | EACH |
|---|
| 38 | 30.2 | 200mm long. | | 18 | EACH |
|---|
| 39 | 31 | S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed for following sizes:- | | | |
|---|
| 40 | 31.1 | 100mm long. | | 6 | EACH |
|---|
| 41 | 31.2 | 125mm long. | | 24 | EACH |
|---|
| 42 | 32 | S & F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. | | 3 | EACH |
|---|
| 43 | 33 | M & L for TMT bars 6 to 8 mm dia, cut to length, bent to shapes required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. | | 40 | Kilogram |
|---|
| 44 | 34 | S & F mild steel conforming to Fe-290 Gde E-165 as in wind ties for roof, or for hold fasts, clamps etc and similar small articles including securing bolts, drilling hole and similar work complete all as specified and directed. | | 6 | Kilogram |
|---|
| 45 | 35 | M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. | | 1865 | Kilogram |
|---|
| 46 | 36 | S & F Hollow mild steel sections (Square/rectangular) for structural use (Reference IS: 4923) as in frame work, braces etc, drilled for fixing covering (exclusive of covering) complete all as specified and directed. | | 470 | Kilogram |
|---|
| 47 | 37 | S&F mild steel work in tubular trusses, purlins and posts including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161 grade St-240 including notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts including rivets or nuts and bolts, providing and fixing cleats, fish plates, gusset plates etc and also for wedging, plumbing, turning up & fixing complete all as specified and directed. | | 400 | Kilogram |
|---|
| 48 | 38 | S & F for mild steel screw bolts (purpose made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 30cm long and dia of neck not exceeding 12mm complete all as specified and directed | | 1.5 | Kilogram |
|---|
| 49 | 39 | S & F for pre-painted galvalume aluminum zinc coating GI based trapizoidal profile steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed. | | 20 | Square Metre |
|---|
| 50 | 40 | S & F 25 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame/fixed to iron frame work/fixed to aluminium frame as in covering, partitions, shelves, cup board or similar items including 4 mm thick first class hard wood teak wood external beading/lipping and fixing in position complete all as specified and directed. | | 20 | Square Metre |
|---|
| 51 | 41 | Supply, fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium door shutters, side hung type divided into panel, including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated aluminium fittings complete all as specified and directed and described hereunder :\n(i) Cross section of chowkat frame 101.60x44.45x2mm thick.\n(ii) Cross section of hanging and meeting style 83x44x2mm thick.\n(iii) Top rail of cross section 114x44x2mm thick. \n(iv) Bottom rail of cross section 114x44x2mm thick. \n(v) Locking rail (middle rail) of cross section 83x44x2mm thick.\n(vi) 5.5mm thick sheet glass, ordinary quality exc 0.50 sqm in each pane \n(vii) Aluminium handle disc type 02 Nos per shutter (one inside & one out side).\n(viii) Aluminium door stopper heavy duty 01 No per shutter.\n(ix) Aluminium tower bolt 200mm long 01 No per shutter. \n(x) Lock and key as approved by Engr-in-Charge of superior quality openable from both side from inside and outside. Make Godrej or eqivalant. | | 2.2 | Square Metre |
|---|
| 52 | 42 | M & L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel, heavy duty of size 125x240x60mm and fixed, complete all as specified and directed. Make : SANDHU/AMAR. | | 1 | EACH |
|---|
| 53 | 43 | Supply,and fixing Glazed partition fabricated from powder coated (Thickness of powder coating not less than 50 micron) aluminium extruded section 101.60x44.45x2mm thick with 5.5mm thick sheet glass, ordinary quality in panels including necessary jointing cleats, glazing clips, aluminium beading, neoprene dry set rubber gasket complete all specified and directed.\n(Note : 5.5mm thick sheet glass, ordinary quality panels is deemed to be included in quoted rates) | | 19 | Square Metre |
|---|
| 54 | 44 | M & L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) as in flooring and finished even and smooth without using extra cement complete all as specified and directed. | | 73 | Square Metre |
|---|
| 55 | 45 | M & L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, for laying floor finishes complete all as specified and directed. | | 69 | Square Metre |
|---|
| 56 | 46 | M & L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes complete all as specified and directed. | | 143.5 | Square Metre |
|---|
| 57 | 47 | M & L for applying cement slurry over existing floor surface @ 3 Kg/Sqm complete all as specified and directed. | | 158.5 | Square Metre |
|---|
| 58 | 48 | M & L for 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as directed. | | 97.5 | Square Metre |
|---|
| 59 | 49 | M & L for 100mm thick PCC (1:2:4) type B-2 using 40mm graded stone aggregate as in sub base complete all as directed. | | 16 | Square Metre |
|---|
| 60 | 50 | M & L for joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and as directed. | | 26 | Square Metre |
|---|
| 61 | 51 | M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed. | | 89 | Square Metre |
|---|
| 62 | 52 | M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed. | | 97.5 | Square Metre |
|---|
| 63 | 53 | M & L 16-18 mm thick granite (of any type) work (table rubbed and polished) in steps jambs pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. | | 6 | Square Metre |
|---|
| 64 | 54 | S & F chequered coloured cement concrete tiles 25cm x 25cm x 22mm thick set, jointed and pointed in neat cement slurry and pointed with grey cement and pigment to match the colour of tiles in floor complete all as specified and directed. | | 8 | Square Metre |
|---|
| 65 | 55 | M & L for 60mm thick PVC moulded precast interlocking paving blocks factory casted using grey cement and pigment, casted in an automatic plant working on vibration and simultaneous hydraulic compression from top, confirming to IS-15658-2006 and of shape haxagon/ triangular/ zigzag/ I-shaped etc. as directed having compressive strength not less than 350 Kg/ Sqcm laid over and including 25 to 30mm thick layer of sand cushioning including filling the interstices with & including sand and interstices on edges filled with PCC 1:2:4 type B-1 finished even and smooth without using extra cement complete all as directed. | | 16 | Square Metre |
|---|
| 66 | 56 | M & L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado complete all as specified and directed. | | 264 | Square Metre |
|---|
| 67 | 57 | M & L for rendering 10 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed. | | 30 | Square Metre |
|---|
| 68 | 58 | M & L for rendering 15 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed. | | 164 | Square Metre |
|---|
| 69 | 59 | M&L for rendering 15 mm thick in CM 1:4 mixed with WPC @ 3% by weight of cement on external surface of brick or concrete and finished the surface even smooth without using extra cement complete all as specfified and directed.\n(Note :- Supply only WPC shall be measured and paid separately) | | 65 | Square Metre |
|---|
| 70 | 60 | M & L for joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exceeding 0.36 sqm, as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. | | 5 | Square Metre |
|---|
| 71 | 61 | M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. | | 8 | Square Metre |
|---|
| 72 | 62 | M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. | | 138 | Square Metre |
|---|
| 73 | 63 | M&L 300x200x7 mm thick glazed ceramic coloured tiles as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. | | 112.5 | Square Metre |
|---|
| 74 | 64 | S & F 3mm thick sheet glass ordinary quality and glazing with beads fixed with metal pins in squares n exc 0.5 sq. m in each pane complete all specified and as directed. | | 3.5 | Square Metre |
|---|
| 75 | 65 | M & L for preparing newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed. | | 134 | Square Metre |
|---|
| 76 | 66 | M & L for preparing old or previously treated walls surfaces by brooming down or with steel wire brushes, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on walls complete all as specified and directed. | | 120 | Square Metre |
|---|
| 77 | 67 | M & L for preparing old or previously treated walls surfaces by brooming down or with steel wire brushes, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coats of white wash on walls complete all as specified and directed. | | 50 | Square Metre |
|---|
| 78 | 68 | M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed. | | 65 | Square Metre |
|---|
| 79 | 69 | M & L for complete removal of existing treatment on walls, chajjas etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of cement base paint complete all as specified and directed. | | 80 | Square Metre |
|---|
| 80 | 70 | M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1mm thick wall care putty complete all as directed.\n(Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.) | | 60 | Square Metre |
|---|
| 81 | 71 | M & L for complete removal of existing treatment on walls including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered and other surfaces of walls, priming plastered and other surfaces with alkali resistant priming paint and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete all as specified and directed.\n(Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.) | | 200 | Square Metre |
|---|
| 82 | 72 | M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed. | | 15 | Square Metre |
|---|
| 83 | 73 | M & L for preparation of old painted wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint of 1st grade quality complete all as specified and directed. | | 35 | Square Metre |
|---|
| 84 | 74 | M & L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed. | | 98 | Square Metre |
|---|
| 85 | 75 | M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality complete all as specified and directed. | | 20 | Square Metre |
|---|
| 86 | 76 | M&L for preparing surfaces and treating small articles such as stop, covers,gully grating, holdfasts, ends of posts, back of chowkats etc, area tarred not exc 0.1 sqm each with tar or coal tar black paint complete all as specified and directed. | | 0.26 | 100\nNos |
|---|
| 87 | 77 | M&L for preparing surfaces and treating ends of posts, backs of chowkaats etc area tarred exc 0.1 sqm but n exc 0.5 sqm each with tar or coal tar black paint complete all as specified and directed. | | 0.05 | 100\nNos |
|---|
| 88 | 78 | S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:- | | | |
|---|
| 89 | 78.1 | 15mm bore. | | 75 | Running\nMetre |
|---|
| 90 | 79 | Fixing only old serviceable steel water tubing, galvanized, medium grade, with all new fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:- | | | |
|---|
| 91 | 79.1 | 15mm bore. | | 20 | Running\nMetre |
|---|
| 92 | 80 | S & F 15mm bore bib tap cast copper alloy fancy type chromium plated long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. | | 57 | EACH |
|---|
| 93 | 81 | S & F 15 mm dia cast copper alloy Chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. \n(Product Code & Make :- Cat Part No.- 8710 of Make Prayag or equivalent model of other makes listed in list of makes). | | 3 | EACH |
|---|
| 94 | 82 | S & F in repairs PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and directed. | | 3 | EACH |
|---|
| 95 | 83 | S & F in repair vitreous China urinals Half stall type, Model Aquaseal N of Parryware, Cat Part No C-0578 (outlet) or equivalent model of Make of Cera/Johnson/Prayag of size 305x305x440mm, white providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with & including PTMT grating and union for dishcharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed. | | 3 | EACH |
|---|
| 96 | 84 | S & F in repairs PVC waste pipe 40mm bore fixed to waste coupling of kitchen sink complete all as specified and as directed. | | 31 | EACH |
|---|
| 97 | 85 | S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed. | | 4 | EACH |
|---|
| 98 | 86 | S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed. | | 4 | EACH |
|---|
| 99 | 87 | S & F in repairs kitchen sink (without drainage board) made of stainless steel 1 mm thick sheet with plug washer and waste coupling including bedding in cement mortar to dwarf wall or including and fixing cantilever brackets and connecting union pipe overall size 495mm x 420mm and bowl size 410 x 330 x 160mm complete all as specified and directed. | | 31 | EACH |
|---|
| 100 | 88 | S & F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including including one No 15mm bore fancy type pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered HOT or COLD with long screwed shanks and fly nuts, screwed for iron pipe, one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed. | | 3 | EACH |
|---|
| 101 | 89 | S & F in repairs 40mm dia waste coupling of PTMT (half or full threaded) minimum weight 60 gms complete all as specified and directed. | | 31 | EACH |
|---|
| 102 | 90 | S & F in repairs grating doom 100 mm dia of PTMT (minimum weight 25 gms), complete all as specified and directed. | | 40 | EACH |
|---|
| 103 | 91 | S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed for following sizes:- | | | |
|---|
| 104 | 91.1 | 75mm bore | | 20 | Running Metre |
|---|
| 105 | 92 | S & F PVC (SWR) bend with oval access door of any radius complete all as specified for following sizes:- | | | |
|---|
| 106 | 92.1 | 75mm bore | | 12 | EACH |
|---|
| 107 | 93 | S & F 75mm bore PVC (SWR) junction, single (single T) equal or unequal complete all as specified and directed for following sizes:- | | 9 | EACH |
|---|
| 108 | 94 | S & F in repairs PVC (SWR) nahani trap 75mm dia outlet plain with CP grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as directed. | | 12 | EACH |
|---|
| 109 | 95 | S & F reinforced concrete pipes, class NP-2, laid and jointed complete with collars and tested complete all as specified and directed for following bore pipes:- | | | |
|---|
| 110 | 95.1 | 300mm bore. | | 16 | Running\nMetre |
|---|
| 111 | 96 | S & F in repairs 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/Cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed. | | 3 | Running\nMetre |
|---|
