Garment Cubicle Change Room Cabinet Comprising Garment Cabinet On Upper Part And Shoe Cabinet On Lower Part. Change Room Cabinet Size:1200Mm ( L ) X 2050Mm ( Ht ) X 400Mm ( D ) Refer To Item ( A ) In Drawing Detailed Description A

Sharing tender

Garment Cubicle Change Room Cabinet Comprising Garment Cabinet On Upper Part And Shoe Cabinet On Lower Part. Change Room Cabinet Size:1200Mm ( L ) X 2050Mm ( Ht ) X 400Mm ( D ) Refer To Item ( A ) In Drawing Detailed Description As Per Soq & Specs. Garment Cubicle Change Room Cabinet Comprising Garment Cabinet On Upper Part And Shoe Cabinet On Lower Part. Change Room Cabinet Size:1200Mm ( L ) X 2150Mm ( Ht ) X 400Mm ( D ) . Refer To Item ( B ) In Drawing Detailed Description As Per Soq & Specs. Garment Cubicle Change Room Cabinet Comprising Garment Cabinet On Upper Part And Shoe Cabinet On Lower Part. Cabinet To Be With Top Side Tapered ( Approx. 30 Degrees ) From Rear To Front To Prevent Accumulation Of Dust And Avoid Strorage Of Item On Top. Material Of Construction Shall Be Ss304 Grade Steel In 16 Swg Thickness With Matt Finish.As Per Technical Specification. Change Room Cabinet Size:600Mm ( L ) X 1900Mm ( Ht ) X 400Mm ( D ) Refer To Item ( C ) In Drawing Garment Cubicle Change Room Cabinet Comprising Garment Cabinet On Upper Part And Shoe Cabinet On Lower Part. Cabinet To Be With Top Side Tapered ( Approx. 30 Degrees ) From Rear To Front To Prevent Accumulation Of Dust And Avoid Strorage Of Item On Top. Material Of Construction Shall Be Ss304 Grade Steel In 16 Swg Thickness With Matt Finish.As Per Technical Specification. Change Room Cabinet Size:600Mm ( L ) X 2150Mm ( Ht ) X 400Mm ( D ) Refer To Item ( D ) In Drawing Garment Cubicle Cabinet With Hepa Filter And Uv Germicidal Light. Change Room Garment Cabinet Of Size 900Mm ( Internal Width ) X 1550Mm ( Ht ) X 600Mm ( D ) Having Filteration System ; Prefilter ( 10 Microns @ 90% Efficiency ) , Hepa Filter 0.3 Microns @ 99.9997% ) , U.V. Germicidal Tube And Blower. Material Of Construction Shall Be Ss304 Grade Steel In 16 Swg Thickness With Matt Finish.As Per Technical Specification. Refer To Item ( H1 ) In Drawing Cross Over Bench Cross Over Bench Having Ss Shelf On Each Side For Shoe Storage Say E Format ) . There Shall Be No Gap At Bottom / Bottom Flushed To Ground. Cross Over Bench Size:1800Mm ( L ) X 600Mm ( Ht ) X 400Mm ( D ) Refer To Item ( E ) In Drawing Detailed Description As Per Soq & Specs. Cross Over Bench Cross Over Bench Cross Over Bench Having Ss Shelf On Each Side For Shoe Storage ( Say E Format ) . Cross Over Bench Size:1400Mm ( L ) X 600Mm ( Ht ) X 400Mm ( D ) Refer To Item ( E ) In Drawing2 Detailed Description As Per Soq & Specs. Sink Module Table Shall Be In Ss304 Grade Steel, Sheet Thickness16 Swg Having Integrated Sink And Drip Tray In It For Use In Wash Area For Equipment Washing With Back Protection To Prevent Spillage. Detailed Description As Per Soq & Specs. Sink Module Sink Module In Ss 304 Grade Steel, Sheet Thickness 16 Swg Having Single Sink Unit With Back Protection To Prevent Spillage. Size:450Mm ( L ) X 300Mm ( W ) X 250Mm ( Ht ) Overall Height Of Cabinet Should Be 850 Mm Detailed Description As Per Soq & Specs. Revolving Stool Sitting Revolving Stools With Sturdy Four Legged Base Moc Ss 304 Surface Finish Mat Seat :Approx. 350 Mm Dia. Adjustable Height :From 550 Mm To 650 Mm ( Manual ) Foot Rest Is To Be Provided. Four Legs With Nylon Bushes Bagging Bin Ss A ) Ideal For Storage Of Laboratory Waste Or Dumping Of Shoe Cover, Plastic, Mass, Caps. B ) Moc Ss 304 , Minimum 16 Gauge Thickness C ) Surface Finish Mat D ) Light Weight High Storage Capacity. E ) Swing Type Lid. F ) Round Type With Castor Wheels. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Round Type Ss Bin Size:500Mm ( Dia ) X 800Mm ( Ht ) Refer To Item ( G ) In Drawing Storage Racks Storage Racks With 16 Gauge Square Pipe Support ( Box Type ) , Ss304 Construction With Adjustable Shelf Height With Loading Capacity Of 200 Kgs Each Shelf. Storage Rack To Have Nylon Bush And With Suitable Bottom Clearance From Floor For Enabling Cleaning Under It. Rack Will Have Four Number Of Shelfs And Space Between Each Shelf Shall Be 600Mm ( Adjustable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. 1200Mm X 600 Mm ( Lxd ) With Three Number Of Shelfs And Space Between Each Shelf Shall Be 600Mm ( Adjustable ) . Storage Racks Storage Racks With 16 Gauge Square Pipe Support ( Box Type ) , , Ss304 Construction With Adjustable Shelf Height With Loading Capacity Of 200 Kgs Each Shelf. Storage Rack To Have Nylon Bush And With Suitable Bottom Clearance From Floor For Enabling Cleaning Under It. Rack Will Have Four Number Of Shelfs And Space Between Each Shelf Shall Be 600Mm ( Adjustable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. 900Mm X 600 Mm ( Lxd ) With Three Number Of Perforated Shelfs And Space Between Each Shelf Shall Be 600Mm ( Adjustable ) Eye Wash Station ( Pedestal Mounted ) Sink Module In Ss 304 Grade Steel, Sheet Thickness 16 Swg Having Single Sink Unit With Back Protection To Prevent Spillage. Detailed Description As Per Soq & Specs. Ss Trolley Ss 304 Trolley In Ss304 Construction. ( To Accommodate Minimum 12 Nos. Of Ss Trays Of Size 530Mmx330mm X80mm Filled With Pp 150Ml / 300 Ml Pp Bottles Detailed Description As Per Soq & Specs. Crates Industrial Plastic Stackable Tubs / Crates With Outer Dimenions 600Mm ( L ) X400mm W ) X325 ( Ht ) Mm Having Hygiene , Nontoxic, Crack And Uv Resistance Properties. Should Be Lightweight And Easy To Handle . This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Ss Tray For Cip Pump Stainsteel 304 Grade Perforated, Easy To Clean Tray With 5 Mm Approx. ) Round Hole In 16 Swg Thickness. ( To Be Accommodated 4 Nos. In Each Shelf Of The Ss Trolleys Aas Described Above Sl. No. 5 ) . Size :530 Mm ( L ) X 330 Mm ( B ) X 80 Mm ( Ht ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Detailed Description As Per Soq & Specs. Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Detailed Description As Per Soq & Specs. Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:1200Mm ( L ) X 600Mm ( W ) X 900Mm ( Ht ) Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:1000Mm ( L ) X 600Mm ( W ) X 900Mm ( Ht ) Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:900Mm ( L ) X 600Mm ( W ) X 900Mm ( Ht ) Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:2000Mm ( L ) X 800Mm ( W ) X 900Mm ( Ht ) , Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So. Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:1000Mm ( L ) X 600Mm ( W ) X 750Mm ( Ht ) , Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support, And Ss Bottom Legs Having Level Adjustment Provision And Nylon Bush. Base Structure :50 X 50Mm Sq. Pipe. ( Suitable Round Pipe Shall Also Be Acceptable ) . Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. This Being A Nonstandard Item : Vendor Can Provide A Better Option If Feel So.Vendor Should Obtain Ga Drawing Approval Prior To Fabrication. Size:1800Mm ( L ) X 750Mm ( W ) X 900Mm ( Ht ) / Height Shall Be Adjustustable ± 100Mm Ss Table ( No. ) Table Shall Be In Ss304 Grade Steel Having Sheet Thickness 16 Swg With Proper Base Support And With Vibration Isolation Rubber Pads ( Anti Vibration Design ) And Ss Bottom Detailed Description As Per Soq & Specs. Storage Cabinet Storage Cabinet Top Side Tapered From Rear To Front To Prevent Of Collection Of Dust. All Three Side Of Cabinet Should Be Blanked With Ss Sheet Front Side Should Be Provided With Doors. 3 Selfs Is To Be Provided With Adjustable Height. Moc Ss 304, Minimum 16 Gauge Thickness Surface Finish Mat Proper Hinges Is To Be Provided So To Avoid Loosening Of Doors Operations. Moc Of Hinges Shall Be Ss304 Or Better. Locks Shall Be Cam Locks Of Standard Makes Swing Open Type Door Leg Is To Be Made Of Ss Round Pipe With Nylon Bush Robust Structure With Proper Stiffeners Wherever Applicable Size:900Mm ( L ) X 650 Mm ( W ) X 1800Mm ( Ht ) , Cross Over Bench Cross Over Bench Having Ss Shelf On Each Side For Shoe Storage ( Say E Format ) . There Shall Be No Gap At Bottom / Bottom Flushed To Ground. Material Of Construction Shall Be Ss304 Grade Steel In 16 Swg Thickness With Matt Finish. Stainless Steel Fabrication Shall Be As Per Gmp Accepted Standard And All Surface Should Be Smooth And Free From Sharp Edges, Corners, Crevices Etc. For Orientation ; Location And Number Of Cabinets Please Refer To Relevant Tender Drawing. Cross Over Bench Size:1600Mm ( L ) X 600Mm ( Ht ) X 400Mm ( D ) Refer To Item ( E ) In Drawing