Two Years Rate Contract For Repairing , Rewinding And Overhauling Of Submersible Motor / Pump , Mono Block Motor / Pump And Ceiling Fans At Nsut During The Year 2021-22 And 2022-2023 .
Tender Value
Ref. Documents
Estimated cost
Bid Submission
16 Apr 2021
0 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
NSUT SECTOR 3 DWARKA NEW DELHI → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Two Years Rate Contract For Repairing , Rewinding And Overhauling Of Submersible Motor / Pump , Mono Block Motor / Pump And Ceiling Fans At Nsut During The Year 2021-22 And 2022-2023 .
BOQ
| Name of work:– Two years rate contract for repairing rewinding & overhauling of Submersible Motor/Pump, Mono Block Motor/Pump & Ceiling Fans at NSUT during the year 2021-2022 & 2022-2023 | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | 1 Rewinding of following ratings / sizes of ceiling fan / exhaust fans with super enamelled copper winding wire of suitable size i/c varnishing, greasing and providing insulation paper between winding wires i/c nuts & bolts machining work etc. as required. [Note: Dismantled / Scrap materials will be the contractor property].\na) 1200 mm / 1400 mm ceiling fans.\n | 566 | each | |
| 2 | 2 | b) 225 mm exhaust fans. | 135 | each | |
| 3 | 3 | c) 300 mm exhaust fans | 135 | each | |
| 4 | 4 | d) 400 mm exhaust fans | 7 | each | |
| 5 | 5 | 2 Rewinding of following ratings motor of monoblock pump with super enamelled copper winding wire of suitable size i/c varnishing, greasing and providing insulation paper between winding wires i/c nuts &bolts machining work etc. as required. [Note: Dismantled / Scrap materials will be the contractor property].\na) 0.5 HP single phase monoblock pump motor.\n | 2 | each | |
| 6 | 6 | b) 1 HP single phase monoblock pump motor. | 4 | each | |
| 7 | 7 | c) 3 HP single phase monoblock pump motor. | 2 | each | |
| 8 | 8 | d) 5 HP three phase monoblock pump motor. | 2 | each | |
| 9 | 9 | e) 7.5 HP three phase monoblock pump motor. | 3 | each | |
| 10 | 10 | f) 10 HP three phase monoblock pump motor. | 2 | each | |
| 11 | 11 | g) 15 HP three phase monoblock pump motor. | 16 | each | |
| 12 | 12 | 3 Rewinding of following ratings / sizes of submersible motor with super enamelled copper winding wire of suitable size i/c varnishing, greasing and providing insulation paper between winding wires i/c nuts &bolts machining work etc. as required [Note: Dismantled / Scrap materials will be the contractor property].\na) 3 HP Submersible motor.\n | 2 | each | |
| 13 | 13 | b) 5 HP Submersible motor. | 3 | each | |
| 14 | 14 | c) 7.5 HP Submersible motor. | 5 | each | |
| 15 | 15 | d) 10 HP to 12.5 HP Submersible motor. | 9 | each | |
| 16 | 16 | 4 Supplying and fixing following accessories on existing ceiling fans / exhaust fan motor including dismantling the old etc. as required. [Note: Dismantled / Scrap materials will be the contractor property].\na Ball bearing of following sizes:\n (i) 6201 \n | 568 | each | |
| 17 | 17 | (ii) 6202 | 528 | each | |
| 18 | 18 | b (i) Gun Metal Bush | 154 | each | |
| 19 | 19 | 5 Overhauling and servicing of ceiling fans including replacement of rubber bush, nuts and bolts with washers, oiling etc. as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 200 | each | |
| 20 | 20 | 6 Replacement of dismantled / faulty / worn out parts of 3.0 HP to 5.0 HP three phase submersible motor including fixing in the motor i.e. rotor sleeves, gun metal bearing bush, water seal, seal bush, thrust bearing, sand guard & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 3 | job | |
| 21 | 21 | 7 Replacement of dismantled / faulty / worn out parts of 7.5 to 10.0 HP three phase submersible motor including fixing in the motor i.e. rotor sleeves, gun metal bearing bush, water seal, seal bush, thrust bearing, sand guard, flanged stud & nuts & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 1 | job | |
| 22 | 22 | 8 Replacement of dismantled / faulty / worn out parts of 12.50 HP to 15.0 HP three phase submersible motor including fixing in the motor i.e. rotor sleeves, gun metal bearing bush, water seal, seal bush, thrust bearing, sand guard, flanged stud & nuts & other minor part etc. complete as required.[Note: Dismantled / Scrap materials will be the contractor property]. | 2 | job | |
| 23 | 23 | 9 Replacement of dismantled / faulty / worn out parts of 3.0 HP three phase submersible pump i.e. pump sand guard, pump shaft one stage, Additional stage, impeller, impeller remetalling & turning & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 5 | job | |
| 24 | 24 | 10 Replacement of dismantled / faulty / worn out parts of 5.0 HP three phase submersible pump i.e. pump sand guard, pump shaft one stage, Additional stage, impeller, impeller remetalling & turning & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 5 | job | |
| 25 | 25 | 11 Replacement of dismantled / faulty / worn out parts of 7.5 HP three phase submersible pump i.e. pump sand guard, pump shaft one stage, Additional stage, impeller, impeller remetalling & turning & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 4 | job | |
| 26 | 26 | 12 Replacement of dismantled / faulty / worn out parts of 10.0 HP to 15.0 HP three phase submersible pump i.e. pump sand guard, pump shaft one stage, Additional stage, impeller, impeller remetalling & turning & other minor part etc. complete as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 7 | job | |
| 27 | 27 | 13 Lifting of submersible motor pump set from the existing bore well (100 feet to 150 feet) of different capacity with help of chain pulley & tripot etc. as required. | 22 | set | |
| 28 | 28 | 14 Lowering of submersible motor pump set in to the existing bore well (100 feet to 150 feet) of different capacity with help of chain pulley & tripot etc. as required. | 21 | set | |
| 29 | 29 | 15 Providing and fixing to filter and lowering to proper levels of following G.I. pipes for tube well including cleaning and priming the tube well.\na) 65 mm dia. nominal bore\n | 147 | meter | |
| 30 | 30 | 16 Supplying, Installation, Testing and Commissioning of 15 HP Star-Delta starter panel suitable of open wall 415 volt 50Hz A/c supply including voltmeter, Ammeter relay, prevention contactor including testing etc.as required. | 2 | each | |
| 31 | 31 | 17 Repairing of 12.50 HP to 15.00 HP star / delta Starter including replacement of connector, preventer, relay and all defective parts internal wiring, interconnection, testing & commissioning etc. complete as required. | 1 | each | |
| 32 | 32 | 18 Supplying and fixing of following item in the GI pipe etc. complete as required.\na) 65 mm G. I. Socket. \n | 9 | each | |
| 33 | 33 | 19 Supplying & fixing of MS channel frame heavy duty at bottom of 15 HP monoblock pump motor including testing etc. as required | 1 | each | |
| 34 | 34 | 20 Supplying and fixing of 32 mm dia. PVC column pipe in the existing borewell for submersible etc. complete as required. | 100 | meter | |
| 35 | 35 | 21 Making arrangement for testing the bore well with bookee and other equipments including labour charges etc. complete as required. | 4 | each | |
| 36 | 36 | 22 Up-gradation of borewell (Digging work) upto 150 feet depth etc. complete as required. | 3 | job | |
| 37 | 37 | 23 Supplying and fixing of 3 core X 6 sqmm copper flate cable for submersible motor pump set etc. complete as required. | 400 | meter | |
| 38 | 38 | 24 Supplying and fixing of adaptor etc. complete as required. | 3 | each | |
| 39 | 39 | 25 Supplying and fixing 150 mm dia. Long & 25 mm dia. GI nipple etc. complete as required. | 3 | each | |
| 40 | 40 | 26 Supplying and fixing 32 / 20 mm. dia. Elbow etc. complete as required. | 3 | each | |
| 41 | 41 | 27 Supplying and fixing GI clamp heavy duty with nuts & bolts etc. complete as required. | 3 | each | |
| 42 | 42 | 28 Making foundation for submersible pipe etc. complete as required | 3 | each | |
| 43 | 43 | 29 Supplying and fixing of following item in the 65 mm dia. GI pipe etc. complete including dismantling old existing as required:– \na) 65 mm GI socket\n | 20 | each | |
| 44 | 44 | b) Reducer socket 2.50” X 2” | 1 | each | |
| 45 | 45 | c) Nipple 2” X 1/2” | 1 | each | |
| 46 | 46 | d) Nipple 2” X 12” | 1 | each | |
| 47 | 47 | e) MS clamp 2.5” | 2 | each | |
| 48 | 48 | f) Union | 1 | each | |
| 49 | 49 | g) Elnow 2.5” | 1 | each | |
| 50 | 50 | h) Reducer 2.5” X 3” | 1 | each | |
| 51 | 51 | 30 Rewinding of following ratings / sizes of wall fans with super enameled copper winding wire of suitable size i/c. varnishing, greasing and providing insulation paper between winding wires i/c. nuts & bolts machining work etc. as required. [Note: Dismantled / Scrap materials will be the contractor property]. \na) 300 mm sweep. \n | 52 | each | |
| 52 | 52 | b) 400 mm sweep. | 4 | each | |
| 53 | 53 | 31 Replacement of faulty 2.50 mfd condenser of ceiling fans etc. as required. [Note: Dismantled / Scrap materials will be the contractor property]. | 791 | each | |
| 54 | 54 | 32 Supplying & fixing of DOL starter of size 5 HP, 3 phase, 445 volt i/c connection, testing etc. as required (Make : L&T ) | 2 | each | |
| 55 | 55 | 33 Lifting and tumbled 5 HP submersible pump set with depth from the 250 feet in existing bore well with help of special heavy labuor, chain pulley and tripod etc. as required (NOTE : this is a rescue job). | 1 | each | |
| 56 | 56 | 34 Rewinding of following ratings / size of submersible pump with super enameled copper winding wire of suitable size i/c varnishing, greasing and providing insulation paper between winding wires i/c nuts & bolts machining work etc. complete a required.\na) 1.0 HP submersible motor \n | 1 | set | |
| 57 | 57 | b) 1.5 HP submersible motor | 7 | set |
AI Tender Summary
Tender Timeline
Apr 10, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedApr 16, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 16, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender