Construction Of Primary Health Sub Center , Bore Well Pumping Machinary And Electrification And Furniture Work At Shewala Tq. Kalamnuri Dist. Hingoli
Tender Value
84.83 Lakhs
Estimated cost
Bid Submission
02 Apr 2021
0 days left
EMD
85000
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kalamnuri → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Primary Health Sub Center , Bore Well Pumping Machinary And Electrification And Furniture Work At Shewala Tq. Kalamnuri Dist. Hingoli
BOQ
| Sl. No. | Item Description |
| 1 | Item No.01:- Excavation for foundation in earth, soil of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for thefoundation and necessary back filling, ramming, water ingincluding shoring and strutting etc. complete. (Lift upto 1.5m.) By Manual Means Spec. No. : BDA 1 SSR ITEM NO. 21.02 & PAGE NO..98 |
| 2 | Item No.02:-Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) Spec. No. : Bd.A.1 Page No. 259 SSR ITEM NO. 21.04 & PAGE NO…… |
| 3 | Item No.03-Providing and filling in the foundation with sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer) Spec.No.Bd.A.13 Page No. 264 SSR Item No.21.39 |
| 4 | ITEM No.4: Providing preconstructional antitermite treatment as per I.S.6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. SSR ItemNo.21.22 |
| 5 | ITEM No.5:Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on bond paper. SSR Item No.21.23 |
| 6 | ITEM No.6:Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper. SSR Item No.21.24 |
| 7 | Item No.07:Providing and laying in situ, cement concrete in M10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, compacting and curingcomplete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer, With natural sand. Spec. No. : BDE 1 SSR ITEM NO. 24.01 & PAGE NO.117 |
| 8 | Item No.08:- Providing and laying in situ/Ready Mixcement concreteM-20of trap / granite /quartzite/ gneissmetal for R.C.C. workin foundations like raft, strip foundations, grillage andfootings of R.C.C. columns and steel stanchionsetc. including bailing out water, formwork, laying/pumpingcover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.3 Page No. 298 and B.7, Page No.38 SSR Item No.25.11 |
| 9 | Item No.09:-Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.5 Page No. 300 and B.7, Page.No. 38 SSR Item No.25.31Ground Floor |
| 10 | First Floor |
| 11 | Item No.10:-Providing & casting in situ cement concrete M20 of trap / granite / quartzite / gneiss metal for R.C.C. beams and lintels as per detailed designs & drawings or as directed including centering, formwork, cover blocks compaction & roughening the surface if special finish is to be provided & curing etc.complete. (Excluding reinfor cement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer).With natural sandSpec. No. :BDF 6 SSR ITEM NO.25.50 & PAGE NO.133 Ground Floor |
| 12 | First Floor |
| 13 | Item No.11:- Providing and casting in situ cement concrete M-20 of trap / granite / quartzite/ gneiss metal for R.C.C. slabs and landings canopy as per detailed designs and drawings including centering, formwork, cover blocks compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer) With natural sand. Bd.F.8 Page No. 302 and B.7, Page No.38 SSR NO.25.70 Ground Floor |
| 14 | First Floor |
| 15 | Item No.12:- Providing & casting in situ cement concrete M-20 of trap / granite / quartzite / gneiss metal for .C.C.chajja as per detailed design & drawings including centering, formwork, cover blocks compacting , curing , finishing & roughening the surface if special finish is to be provided & curing complete. ( Excludingreinfor cement and structural steel) with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer).With natural sand. Bd.F.9 Page No. 303 and B.7, Page No.38 SSR 26.05 Ground Floor |
| 16 | First Floor |
| 17 | Item No.13- Providing and Casting in situ, cement concreteM-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete pardi of required thickness including centering formork, compacting and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement )Bd.F.11 Page No.304 and B.7, Page No. 38 SSR No.26.17 Ground Floor |
| 18 | ITEM No.14: Providing and laying Cast in situ / Ready Mix cement concrete in M-20 of trap / granite / quartzite / gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including centering, form work, cover blocks, laying / pumping,compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. qualityArtificial Sand`Bd. F. 12 Page No. 304 and B-7, Pg 38 SSR I. No.26.23 Ground Floor |
| 19 | First Floor |
| 20 | Item No.15:- Providing and fixing in position T.M.T. bar reinforcement of various diameters for reinforced cement concrete pile caps, footings, foundations, slabs, beams, columns, canopies, stair case, newels, chajjas, lintels, pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules including cutting bending, hooking the bars, binding with wires or tack welding and supporting as required complete. Bd.F.17, Page No. 306 SSR It. No.26.33 Ground Floor |
| 21 | First Floor |
| 22 | ITEM No.16: Filling in plinth and floors with contractors material / brought from outside and approved by Engineer incharge in layers of15cm. to 20cm. including watering and compaction etc. complete. Spec. No. : BBDA 11 ITEM NO 21.37 |
| 23 | ITEM No.17: Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming,watering etc. complete.Spec. No.BDA SSR ITEM NO. 21.40 & PAGE NO.103 |
| 24 | ITEM No.18:Providing second class Burnt BrickProviding second class Burnt Brick masonry with conventional / Indian Standard type bricks in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water manually,striking joints on unexposed faces, raking out joints on exposed faces and watering complete.Bd.G.1 Page No.313 SSR I NO.27.01 G.F. |
| 25 | ITEM No.19:Providing second class Burnt Brick masonry with conventional / Indian Standard type bricks in cement mortar 1:6 in superstructure including striking joints, raking outjoints, watering and scaffolding complete. Spec. No. : Bd.G.5 Page No. 315SSR It. No.27.05 Ground Floor |
| 26 | First Floor |
| 27 | ITEM No.20: Providing second class Burnt Brick masonry with conventional type bricks in cement mortar 1:4 in half brick thick wall including 75 mm thick band in C.C.1:2:4 after every Eleventh layer with mild steel longitudinal reinforcement of 2 bars of 6 mm. diameter , scaffolding ,raking outjoints, watering etc.complete.( The C.C.band to providedalong with M.S.reinforcement.) Spec. No. : Bd.G.7 Page No. 316SSR It.27.06 G.Floor |
| 28 | First Floor |
| 29 | Item No.21:- Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc.On C.M. 1:6 including filling joints with polymer base filler nosing thesharp edges wherever necessary, curing, etc. complete.Spec. No.- As directed by Engineer in Charges. SSR Item No.33.68 G.Floor |
| 30 | First Floor |
| 31 | ITEM No.22: Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete.Spec. No. : Bd.T. 34 Page No. 499SSR It. No.39.09 G.Floor |
| 32 | First Floor |
| 33 | ITEM No.23: Providing and fixing 34 mm thick moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness lipped with 15 mm ( 5mm x 3) thick x 30 mm width on one style and top rail and 10 mm (5mm x 2) thick x 30 mm width on other style and bottom rails. The inner panels laminated with 2 mm thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 design in different plain and /or prelim colours on one side after routing the moulded design on flush doors and 2 mm plain and /or pre lam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etc. as per direction of Engineer in charge and manufacturers specification and drawing etc. complete.SSR Item No.39.48 G.Floor |
| 34 | First Floor |
| 35 | ITEM No.24:Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983). SSR Item No.39.26 Ground Floor |
| 36 | Item No.25:- Providing and fixing M.S. grill door 24 kg/sqm of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc Spec.No.As directed by Engineer in charge. SSR Item No.39.31 First Floor |
| 37 | Item No.26.:- Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box SSR I NO.39.44 G. Floor |
| 38 | First Floor |
| 39 | ITEM No.27: Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR Item No.39.68 G.Floor |
| 40 | Item No.28:- Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. SSR I. No.32.26 |
| 41 | First Floor |
| 42 | ITEM No.29:Providing and applying Two coats of wall care Putty of 2mm thickness for plastered surface and 5-6mm thickness finished concrete surface to Ceiling and Walls to prepare surface even and smooth of Brands BIRLA WHITE, BERGER, BISION, J.K., make, etc complete. a) For plastered walls/ceiling 2mm SSR Item No.32.34 |
| 43 | First Floor |
| 44 | Item No30:Providing internal cement plaster 20mm. thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete. SSR I No.32.07 |
| 45 | First Floor |
| 46 | Item No.31;- Providing sand faced plasterexternally in cement motar using khasalia/ kasaba or similer type of 15 mm. thick in cement mortar 1:4 using waterproofing compound at 1 Kg. per cement bag, curing the same fornot less than 2 days and keeping the surface of the base coat rough to recive the sand faced tretment 10 mm. thick in cement mortar 1:4 finishingthe surface by taking out grains and curing for foureen days scaffolding etc. complete.for compound Wall. (Only for Building works not for compound wall) Spec. :Bd.L .7 Page No. 367SSR It. No.32.11 |
| 47 | First Floor |
| 48 | Item No.32:- Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/including ponding test etc. complete. SSR I.31.05 |
| 49 | First Floor |
| 50 | item No.33- Providing and laying vitrified matt fininsh tiles of RAK/ Kajaria / Nitco /Asian or equivalent make having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 156222006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring Spec. No.-Bd.M.12 Page No.385 SSR Item 33.42 |
| 51 | First Floor |
| 52 | ITEM No.34:Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. b) SkirtingSpec. No.-Bd.M.12 Page No.385 SSR Item No.33.43 Ground Floor |
| 53 | First Floor |
| 54 | Item No.35:-Providing and laying Antiskid Ceramic tiles of approved qualityof company RAK / Kajaria / Nitco / Asian or equivalent make of size 30 cm x 30 cm and confirming to IS 156222006 (GroupB IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. Bd. M12 page No.385 SSR I NO.33.67Ground Floor |
| 55 | First Floor |
| 56 | Item No.36:- Providing and laying ceramic tiles ofhaving size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. Spec.No.Bd.M.13 Page No. 386. SSR Item No.33.25 |
| 57 | First Floor |
| 58 | ITEM No.37: Providing and laying handcut polished Kotah Stone flooring 25mm to 30mm thick and 30cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling jointswith neat cement slurry, curing, polishing and cleaning etc. complete. Spec.No.Bd.M.3 Page No.380 SSR No. 33.07 |
| 59 | First Floor |
| 60 | ITEM No.38:Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 mm thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc.complete.SpecBd.M.22 Page No. 390 SSR Item No.33.18 |
| 61 | First Floor |
| 62 | ITEM No.39: Providing 25 mm to 30 mm thick partition of polished black kadappa stone slab of approved quality including giving required size and shape etc. Fixing in cement mortar 1:3 curing and cement etc. complete. b) Both side polish. spec.No.-Bd.M.35 B/P No.393 SSR I No.33.33 Ground Floor |
| 63 | ITEM No.40: Providing and fixing black kadappa stone as shelves 25mm.thick machine polished, extending the polish upto 20 cm width on lowerside, rounding corners, laying in position jointing with bedding cement mortar 1:4 proportion curing etc etc. complete. Spec. No.Bd.M.29 Page No. 391 SSR Item No.33.23 |
| 64 | First Floor |
| 65 | Item No.41 - Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking cement concrete paving blocks 80MM thick in M-40 grade of approved size and shape for City streets, small /medium market roads,low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658:2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of natural sand / crushed sand of 50 mm thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibratoretc. complete. Spec No.IRC-SP-63 SSR Item No.5.20 |
| 66 | ITEM No.42:-Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVCpipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.Spec. No. BD.V 5 page 551 and as directed by Engineer in harge SSR Item No.42.55 Ground Floor |
| 67 | First Floor |
| 68 | ITEM No.43:- Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.BD.V 5 page 551 and as directed by Engineer in chargeSSR Item No.42.56 |
| 69 | First Floor |
| 70 | ITEM NO.44:- Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. Spc. No.Bd.V.8 Page No.554 SSR I NO.41.40 |
| 71 | First Floor |
| 72 | Item No.45:- Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete. Spec. No.Bd.V.9 Page No. 555 SSR Item No.41.44 Ground Floor |
| 73 | Item No.46:-Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete. SSR Item No.42.31 |
| 74 | First Floor |
| 75 | ITEM No.47: Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete. Spec.No.As directed by Engineer in Charges. SSR Item No.42.20 |
| 76 | First Floor |
| 77 | ITEM No.48:Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete. Spec. As directed by Engineer in charge. SSR Item NO.42.33 |
| 78 | First Floor |
| 79 | Item No.49: Providing and fixing European type white glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall 10 litre enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps,20 mm dia.UPVC overflow pipe ,mosquito proof couplings G.I. chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete.(prior pproval of sample and brand by Ex. Engineer is necessary before use) Bd.V.21 SSR Item No.43.19 Ground Floor |
| 80 | Item No.50:- Providing and fixing coloured glazed earthenware Wash Hand Basin of 55cm x 40 cm size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface,testing etc. completer. Spec. No.Bd.V.30 Page No.565 SSR I. No. 41.66 |
| 81 | First Floor |
| 82 | Item No.51:-Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 mm dia. and vertical pipe of 38 mm dia at 0.60 m c/c or as required and horizontal pipes of 25 mm dia in three rows, all pipes of 2 mm thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75 mm dia above newel post of 75 mm diameter etc. complete (Prior approval of sample and brand by Ex.Engineer is necessary before use) SSR I No.40.08 First Floor |
| 83 | ITEM No.52: Providing and fixing 10 cm PVC nahani trap with grating etc. complete Spec. No.BD.V 32 A page 551 and as directed by Engineer in charge SSR item No.42.67 Ground Floor |
| 84 | First Floor |
| 85 | ITEM No.53:- Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes,inluding fixing the pipe on wall using approved wooden cleatsprojecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment) Spec. No.As directed by Engineer InchargeSSR I No.42.87 Grond Floor |
| 86 | First Floor |
| 87 | Item No.54:- Providing & constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. SSR Item No.42.12 |
| 88 | Item No.55:- Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. SSR Item No.42.13 |
| 89 | Item No.56;-Providing and applying plastic emulsion paint of approved quality, colour and shade to old & new surfaces in three coats including scaffolding, preparing the surface. (excluding the primer coat) etc. complete. Spec.No.Bd.P.6 Page No.414SSR I No.36.14 |
| 90 | First Floor |
| 91 | ITEM No.57: Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item No. 15 to 18 prior approval of Superintending Engineer will be necessary. Spec. No.As directed by Engineer in charge. SSR Item No.35.26 |
| 92 | First Floor |
| 93 | Item No.58:- Providing internal cement plaster 20mm. thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete. SSR I No.32.07 Ground Floor |
| 94 | ITEM No.59: Providing cement based water proofing treatment to terraces (Indian water proofing or alike) witProviding and fixing in position Low height Storage as per drawing in 19 mm plywoodframe finished with 1 mmdecorativelaminateconfirming to I.S. 2046 (regular type). Size ofcupboardis 1.20x0.45x0.75 mts. Back of cupboard will be in 12mm plywood. Cupboard will have one shelf with shuttters, shutter and lock, All the cut edges will be covered by first quality TW beeding. All Internal surfaces will be finished with 1.5 mm. white laminte etc.aid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. Spec.No. As directed by Engineer in charge SSR Item No. 31.04 |
| 95 | First Floor |
| 96 | Item No.60;- Providing fine cement finish 1.5 mm. thick over green plaster surface including scaffolding and curing etc. complete. Spec. :As directed by Engineer in charge SSR It. No.32.21Ground Floor |
| 97 | ITEM No.61: Providing groove to required size at specified location as directed by Engineer, at junction of brick masonry wall and R.C.C beams or Column, at junction of composite masonry, including scaffolding, finishing, curing etc. complete.Spec. :As directed by Engineer in charge SSR Item No.32.37 |
| 98 | First Floor |
| 99 | ITEM No.62: Providing water proofing treatment as per IS : 1346-1966 to generally inaccessible sloping Reinforced Cement Concrete Terrace slab with bitumen felts in all positions in five course, consisting of applying cold bitumen primer coat at the rate of 2.5 litre per 10 Sqm., hot bitumen layer at the rate of 14.50 kgper 10 Sqm. and over the same layer of bitumen felt of type III grade (I) as per IS: 1332-1965 across the slope with 10 cm overlap commencing at lowest level and again applying hot bitumen course at the rate of 14.50 kg per 10 Sqm. and finally spreading over it grit at the rate of 14.50 kg per 10 Sqm. including all lifts, leads and scaffolding whenever necessary complete as directed with four years\" guarantee on requisite stamp paper etc. complete. Spec. No.- As directed by Engineer in Charge. SSR Item No.31.17 |
| 100 | First Floor |
| 101 | Item No.63- Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters ITEM No.42.53 First Floor |
| 102 | ITEM No.64: Providing and applying white-wash in two coat on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. Spec. No. :Bd. P. I Page No. 411 D.S.R.I.No.36.03 |
| 103 | First Floor |
| 104 | ITEM No.65: Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg/sqm as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. Spec.No.:-Bd.U.1 Page No.537 SSR Item No.40.01 |
| 105 | First Floor |
| 106 | Item NO.66-Providing and fixing stainless steel sink of size 600 x 510 x 200 mm incluidng coupling, outlet pipe, elbow and other necessary fitting, finishing etc. complete. SSR Item No.42.78 |
| 107 | Item No.67:-Providing and fixing board displaying information, such as \"Name of work, Tender cost, Name of Contractor, Work completion and liability period etc\", having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge. |
| 108 | Item No.68- Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. Ssr I.No.46.09 |
| 109 | Item No.69:- Removing doors and windows with frames and stacking thematerials as directed with all leads, lifts etc. complete.Ssr I.No.46.15 |
| 110 | Item No.70:- Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete. Ssr I.No.46.19 |
| 111 | Item No.71:- Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete. Ssr I.No.46.29 |
| 112 | Add For Royalty Sand |
| 113 | Add For Royalty Other Materials |
| 114 | Add For Testing chasrges |
| 115 | Add For Insurance |
| 116 | Add For GST |
| 117 | Furniture - Item.No.1) Single Bed @ 2025LX 1000DX 650HProviding and fixing Single Bed of Size 2025Lx1000Dx650Hwith matress and pillow. Understructure: - The legs are made of Square tube of size 25 x 25mm made out of MSwithathicknessof1.2mm.The legsshouldhave cornerbracketsweldedto it attwo levels. The corner brackets are made of 2mm thick CRCA having a L shaped structure to join the side panels and headboard to the leg. Three nos. of Horizontal stiffeners are provided at equal intervals. The stiffeners are made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. The middle Horizontal Stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 x 25mm made out of MS with a thickness of 1.2mm. All Metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 Microns DFT. (SSR 2020-2021 I.No. 51.55) |
| 118 | Item.No.2)Executive\"sTable @ 1800Lx900Dx750HTProviding & Fixing of Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish withsoft water fall edges & curvedpanel & Decorated Anodizedsection MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing (SSR 2020-2021 I.No. 51.21 ) (Inspection Table) |
| 119 | Item.No.3)Stool for Lab and Class-IVProviding and fixing 4 legged Lab stool, Legs made of 16 Guage 45 MM Outer dimension MSPipe,Dulypainted,Witha304Grade Stainlesssteel12inchwide seatwitha1inch collar, Height adjustment via a screw. as per design and drawing and instructions of Engineer in charge. (SSR 2020-2021 I.No.51.51) |
| 120 | Item.No.4) Free Standing Table @ 1200Lx600Dx750HTProvidingandfixingTableofSize1200x600x750mm.Top:madefrom25mm Prelaminated Particle board.All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Legs:CShape madefrom CRCASheetwithPowderCoatfinish.Modestypanel:Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :-Metal Powder Coated - Black Color, CPU TROLLEY:- MetalPowderCoated-BlackColor,3DRAWERPEDESTALUNIThavingoverallsize 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, (SSR 2020-2021 I.No. 51.28) |
| 121 | Item.No.5) Low Height Openable Storage @ 900Lx450x750HTProviding and fixing Openable Steel Storage of 900 x 450 x 750Ht, with 2 adjustable shelves, Complete body & shutter made in0.8 mm thick & Top in 2 mm thick CRCA, 2 Shutter to be mountedwiththehelpofcuphinges,and4adjustablelevelers,enitrestorageinpowder coated finish with 60 to 80 microns. with 25 mm. thk additional Top on top of storage as as per drawing (SSR 2020-2021 I.No. 51.35) |
| 122 | Item.No.6) Public Seating Chair. - 3 SeaterProvidingandFixing3seaterPublicseatingchairmadeofcompletemetalwithLegsin Crome finish and seates in silver powder coating finish. (SSR 2020-2021 I.No. 51.44) |
| 123 | Item.No.7)Qualtiy Control Test Report :- Determination of Resistance to dry heat, Determination of moishitre content. Determination of Density thickness of Plywood. |
| 124 | Electrical Works -capping Patti Item.No.1. Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as perspecification No: WG-MA/CON. 1-2-10 |
| 125 | Item.No.2 Supplying and erecting PVC trunking (PVC casing-ncapping)of size 20 mm with accessories on wall/ceiling asper specification No: WG-MA/CON. 1-2-9 |
| 126 | copper Wire Item.No.3 Supplying & erecting mains with 2x1.5 sq.mm F.R copperPVC insulated wire laid in provided conduit/trunking/insidepole/Bus bars or any other places as per specification No: WGMA/BW 1-3-1 |
| 127 | Item.No.4 Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVCinsulated wire laid in provided conduit/trunking/insidepole/Bus bars or any other places. as per specification No: WGMA/BW 1-3-3 |
| 128 | Item.No.5 Supplying & erecting mains with 2x4 sq.mm F.R copper PVCinsulated wire laid in provided conduit/trunking/insidepole/Bus bars or any other places as per specification No: WGMA/BW 1-3-5 |
| 129 | Item.No. 6 Supplying & erecting mains with 2x6 sq.mm F.R copper PVCinsulated wire laid in provided conduit/trunking/insidepole/Bus bars or any other places as per specification No: WGMA/BW 1-3-7 |
| 130 | Item.No.7 Supplying and drawing of 2x1.5 sq.mm. FR grade copperwires with 1.5 sq.mm earth wire in provided concealed pipesand terminating on modular accessories in box for point wiringfor independent plug as per specification No WG-PW/SW 1-9-12 |
| 131 | Item.No.8.Supplying and erecting ISI mark modular type bell indicator,duly erected on provided plate and box with wiring connections 1-8-18 |
| 132 | oscillatingtype FanItem.No.9 Supplying pedestal type air circulator 600 mm. sweep oscillatingtype suitable to work on 230 Volts 50 cycles 1440 RPM with speedregulator, overhead protection unit, totally enclosed, flame proofmotor with additional 3 core wire, 5 metre length and hand shieldtype 3 pin6A. plug top complete with moisture proof treatment and=E‘ class insulation 2-12-9 |
| 133 | Item.No.10.Supplying and erecting fan clamp of 30 x 5 mm. M.S. flat ofrequired length and 10 mm. M.S. bolt and nuts erected withnecessary hook of 10 mm. M.S. round bar and painted 2-13-3 |
| 134 | exhaust fan Item.No.11.Supplying and erecting exhaust fan heavy duty 230 V A.C. 50cycles 450 mm. 1400 RPM complete erected in position as perspecification no. FG-FN/EXF 2-12-18 |
| 135 | Item.No.12 Providing earthing with galvanized iron earth plate size 60 x 60 x0.6 cm complete with all materials, testing & recording the results asper specification no. EA-EP 9-1-1 |
| 136 | Item.No.13 Supplying and erecting LED square / circular 9 to 12W downlighter having pressure die-cast aluminium housing, opaltranslucent cover, mounting arrangement with board for surfacetype or spring loaded mounting clips for flush type complete. 2-1-3 |
| 137 | Item.No.14 Supplying and erecting UPVC reinforced flexible conduit 25mm in dia. conforming to I.S. with required number ofcouplings, PVC bushes, check nuts etc. complete. 1-2-2 |
| 138 | Item.No.15 Supplying and erecting ISI mark modular type switch 6A / 10Aduly erected on provided plate and box with wiring connections complete |
| 139 | Item.No.16 Supplying and erecting ISI mark modular type switch 16A dulyerected on provided plate and box with wiring connectionscomplete 1-8-2 |
| 140 | Item.No.17 Supplying and erecting ISI mark modular type switch 16 / 20 Awith indicator, duly erected on provided plate and box withwiring connections complete 1-8-3 |
| 141 | Item.No.18 Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete 1-8-11 |
| 142 | Item.No.19 Supplying and erecting ISI mark modular type indicator lamp,duly erected on provided plate and box with wiring connectionscomplete 1-8-12 |
| 143 | Item.No.20 Supplying and erecting ISI mark modular type 6 / 16A fuse unit,duly erected on provided plate and box with wiring connections complete 1-8-13 |
| 144 | Bord Item.No.21Supplying and erecting PVC Surface modular switch box withdouble mounting plate for 4 modules duly erected 1-8-29 |
| 145 | Item.No.22 Supplying and erecting PVC Surface modular switch box withdouble mounting plate for 6 modules duly erected 1-8-30 |
| 146 | Item.No. 23Supplying and erecting PVC Surface modular switch box withdouble mounting & front plate for 8 modules complete dulyconnected 1-8-31 |
| 147 | Item.No.24 Supplying and erecting PVC Surface modular switch box withdouble mounting plate for 12 modules duly erected 1-8-32 |
| 148 | Item.No.25 Supplying and erecting ISI mark modular type blanking platetwo module, duly erected on provided plate & box 1-8-25 |
| 149 | Item.No.26 Supplying and erecting unbreakable concealed type modularswitch box with double mounting plate for 12 module dulyerected flush to wall with required chiselling and finishing withcement mortar / POP as per required to match the background 1-8-40 |
| 150 | Item.No.27 Wiring for plug on board with Switch socket, copper wiringand earthing as per specification No: WG-PW/SW 1-9-13 |
| 151 | Item.No.28 Point wiring in PVC trunking (casing-capping) with 1.5sq.mm (2+1E) FR grade copper wire, flush type switch, earthingand required accessories as per specification No: WG-PW/SW 1-9-16 |
| 152 | Item.No.29 Supplying & erecting LED 20W tube light fitting (4 feet) withaluminium housing, heat sink, integrated HF electronic drivercomplete 2-1-23 |
| 153 | Item.No.30 Supplying erecting and marking four pole isolators only switchversion of miniature circuit breakers of 40A in provided distributionboard complete 5-3-24 |
| 154 | FanItem.No. 31Supplying and erecting regular/ standard model ceiling fan of1400mm. sweep complete erected in position as per specificationno. FG-FN/CF 2-12-3 |
| 155 | Item.No.32 Supplying and erecting electronic type step regulator for ceilingfan 600/ 900/ 1200/ 1400 mm. sweep, complete erected onprovided switch board. 2-13-9 |
| 156 | Item.No.33 Supplying, erecting, testing and commissioning selfcontainedwater cooler 230/250 V 50 cycles nominalcooling capacity of 80 litres/hr and storage capacity 120litres with partially stainless steel body complete.specification no. AP-WCR/WC 3-3-4 |
| 157 | Item.No.34) Supplying and erecting ultra violet storage type waterpurifier ( RO+UV+UF) with softener for safe drinkingwater consisting of UV germicidal tube of 8W capacitychoke made of copper wire and two indicator lamps withoutput of purified water 7 to 8 litre/min with activatedcarbon filter and softener operating on 230 V single phaseA.C. supply. 3-5-1 |
| 158 | Item.No.35) Supplying, erecting & marking SPMCB 6A to 32A, C-series (formotor/power) in provided distribution board as per specificationno. SW-SWR/MCB 5-3-2 |
| 159 | Item.No.36 Supplying, erecting & marking SPMCB 40A to 63A C- series (formotor/power) in provided distribution board as per specificationno. SW-SWR/MCB 5-3-4 |
| 160 | Item.No.37 Supplying, erecting & marking DPMCB 40A to 63A, C- series (formotor/power) in provided distribution board as per specificationno. SW-SWR/MCB 5-3-8 |
| 161 | Item.No.38 Supplying, erecting & marking DPMCB 6A to 32A, C- series (formotor/power) in provided distribution board as per specificationno. SW-SWR/MCB 5-3-6 |
| 162 | Item.No. 39 Supplying & erecting triple pole and neutral distribution board(TPNDB) with door surface/ flush mounted suitable for 3 poleMCCB as incomer & outgoing SP MCB (36 poles) or TP MCBof 12 ways (36 poles) on iron/ GI frame. (vertical busbar type) asper specification no. SW-SWR/MCBDB1 5-4-27 |
| 163 | Item.No.40 Supplying and erecting LED flood light fitting of 70- 80W,including lamp, with PF > 0.95,class IP 65 and above housing ofpressure die cast aluminium alloy and heat sink extruded aluminiumcomplete as per specification No FG-ODF/FLS-2 |
| 164 | Item.No.40 Supplying, installing, testing and commissioning of 800 VA to 900 VA Digital pure sine wave inverter based onInsulated Gate Bipolar Transistor (IGBT) technology singlephase 230V,50 Hz complete as per specification no. APINV(Without batteries) 3-6-2 |
| 165 | Supplying and erecting 12 V/150Ah tubular battery withbattery terminal wire, duly charged complete with 36months warranty complete3-8-4 |
| 166 | Add For GST |
| 167 | Item No. 1:- Drilling the Bore well 150mm dia by D.T.H. Machine including transportation of machine at work site Surface bore. (Rate as per G.S.D.A 2020-21) |
| 168 | Item No. 2:- Taking Yeild Test for V Noch Method (Rate as per G.S.D.A. 2020-21) |
| 169 | Item No. 3:- Providing and Supplying 180 mm Dia 6kg/cm2 PVC Casing pipe etc. complete(As Per GSDA Rate 2020-21) |
| 170 | Item No. 4:- Lowering and laying 180 mm Dia 6kg/cm2 PVC Casing pipe etc. complete(As Per GSDA Rate 2020-21) |
| 171 | Item No. 5:- providing and fixingM.S. Cap heavy duty for 180 mm dia pipe (As per GSDA Rate 2020-21) |
| 172 | Water Supply -Item No-1:- Submercible pumpsets 150 mm dia proiding and erecting end giving test of Submaersiable pump set conforming to IS8034 and motor conforming to IS 9283 with water proof winding.pump shall be sutebale for verious delivery head and discharge with stainless stell shaft motor suteble for working on 415 V=10%, 3ph,50hz A.c.supply,with cable guard ,carbon/fiber thurst bearing to with stand entire hydralic thrust.the pump set shall be suiteble for direct coupling with suitable suction strainer pump should have suitable discharge out let as per manufactures design.Anti thrust stream lined non return valve shall be provided with the pump3m submersiblecopper conductor cable in single/double run and 2pair in erection clamps 65 mm width 10 mm thick shall be provided with each pump Submaersiable pumpsets 150 mm dia (with bronze impeller)up to 8 stages .Submaersiable pump on well 3.00 BHP(MJP Mech.CSR 2019-20 P.No.1 ,PM 1-2-3) |
| 173 | Item No. 2:-Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/ centrifugal pump set upto 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc For Borewell No. 1 (PWD Ele.DSR 2019-20 P.N.219 I.N.12-4-17) |
| 174 | Item No. 3:-Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL(PWD Ele.DSR 2019-20 P.N.128 I.N.7-1-26) |
| 175 | Item No. 4:-Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq mm copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/pole or laid in provided trench/ pipe as per specification no.CB-LT/CU(PWD Ele.DSR 2019-20 P.N.130 I.N.7-2-9) |
| 176 | Item No. 5:-Providing and supplying in standerd lengths High Dencity Polyethelene pipes conforming to I.S.4984/14151/12786/ 13488 with necessary jointing materials like mechanical connector i.e.thread /incert joint/quick release coupler joint /compression fitting jiont flanged jointincluding all local and central taxes transportation and freight charges , inspection charges loding unlodingcharges conveyance to depatmental stores /site and stacking the same inclosed shead dully protcted from sunrays and rainetc complete(MJP.CSR 2019-20 P.N. 111 I.NO. 1) 40 mm dia HDPE/MDPE Pipes |
| 177 | Item No. 6:-Lowering ,laying and jointing HDPE / MDPE pipes in proper position including all specials by Compression fitting / Electrofusion and but fusion jointing procedure including gydraulic testing as per relevent IS Code complete with all materials for jointing procedres like Electrofusion machine, Electric mirror/ heater/ but fusion welding machine with hydraulic jack, top laoding clamp etc pump and accessories for hydraulic testing and alllabhours as directed by engg-incharge as per IS-7634 Part.II.(MJP.CSR 2019-20P.N.107 I.NO. 2) 40 mm dia HDPE/MDPE Pipes |
| 178 | Item No.7:- Providing earthing with galvanized iron earth plate size 60 x 60 x0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP(PWD ele.CSR 2019-20P.N.161 I.No.9-1-1) |
AI Tender Summary
Tender Timeline
Mar 27, 2021
11:30 IST
Tender Published
Tender notice published.
CompletedApr 02, 2021
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 04, 2021
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender