Supply Of Spare Parts Of Cattle Feed Plant Machinery, Cattle Feed Factory Pachama-Madhya Pradesh

TDR : 27295499

Tender Notice
BOQ

Expired

Cattle Feed Factory Pachama , Madhya Pradesh

Tender Brief : Supply Of Spare Parts Of Cattle Feed Plant Machinery

Document Fees
₹ 1000 /-

EMD
₹ 200000.0 /-

Tender Value
Refer document

Submission Date
23-03-2021

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

Name of Work: SUPPLY OF SPARE PARTS OF CATTLE FEED PLANT MACHINERY
1	1	NAME OF THE ITEM FOR PACHAMA
2	1.01	Pallet Mill die 8mm hole Super Senior extra wide Size: 630 mm OD 520mm ID222 mm Phase, 17 Rows of Holes with straight caller & m-20x12 holes both sides on 565 PCD	item1	12	Nos
3	1.02	Roller Shells “V” grooved for above Size 250mm OD 180mm ID(Suitable for Bearing no. 32220, 182 mm wide	item2	50	Nos
4	1.03	Roller Assembly Complete with shell & Bearing etc. Bearing SKF/FAG/ZKL	item3	10	Nos
5	1.04	Die Holder Assembly Complete with “T” Shaft, Bearings 32324 & 32224, Bearing covers, Oil Seals etc. Bearing SKF/FAG/ZKL	item4	1	NO
6	1.05	Die Holder only (Alloy Steel Forging)	item5	1	NO
7	1.06	“T” Shaft with centralized greasing system	item6	1	NO
8	1.07	i) Eccentric Shaft (Alloy Steel) (Spare for Roller Assembly)	item8	4	Nos
9	1.08	ii) Middle Spacer 51 mm wide(Spare for Roller Assembly)	item9	4	Nos
10	1.09	iii) Bearing Cover Plate(Spare for Roller Assembly)	item10	24	Nos
11	1.1	iv) Bearing Pressing Plate(Spare for Roller Assembly)	item11	20	Nos
12	1.11	v) Circlip 180 mm Inner(Spare for Roller Assembly)	item12	50	Nos
13	1.12	vi) Lock nut for Eccentric Shaft m-20(Spare for Roller Assembly)	item13	10	Nos
14	1.13	vii) Lock Nut Washer for above MB-20(Spare for Roller Assembly)	item14	10	Nos
15	1.14	viii) Clamping Device (Setting Ring of male female rings)(Spare for Roller Assembly)	item15	12	Nos
16	1.15	ix) Centre Bolt for roller Alen Type (Unbreako/ TVS/LPS)(Spare for Roller Assembly)	item16	10	Nos
17	1.16	x) Nut for Centre Bolt Attached with 1 male ring & Pin (Spare for Roller Assembly)	item17	12	Nos
18	1.17	Front scraper assembly	item18	2	Nos
19	1.18	Stud for front scraper assembly	item19	24	Nos
20	1.19	Roller locking Assembly with Two Disc and master plate	item20	2	Nos
21	1.2	Share Pin Block	item21	1	Nos
22	1.21	Share Pin 18 mm Dia	item22	500	Nos
23	1.22	Paddles for conditioner of 330 mm die of SS-304 with Stud and Nut	item23	100	Nos
24	1.23	Die Ring rear for Straight collar die (Alloy Steel EN-9)	item24	1	NO
25	1.24	Die Ring front for Straight collar die (Alloy Steel EN-9)	item25	1	NO
26	1.25	Die cover with 4 Hooks size 520 OD x 340 mm ID x 130 mm wide made of SS 304 x 3 mm thick plate SS-304	item26	2	Nos
27	1.26	Main Bearing cover Plate front with Oil Seal 180-150-13 for Bearing 32324	item27	2	Nos
28	1.27	Main Bearing cover Plate Rear with Oil Seal 170-150-13 for Bearing 32224	item28	2	Nos
29	1.28	Main Bearing Pressing Ring front	item29	2	Nos
30	1.29	Main Bearing Pressing Ring rear	item30	2	Nos
31	1.3	Pallet Die Guard Assembly with Pallet cutter made of 6 mm thick SS 304 Plate	item31	1	NO
32	1.31	Feeder Complete with screw about 02 Meter long 400 mm Dia	item32	2	NO
33	1.32	Pallet Mill Main Pully SPC Section 9 Grove x 1220 mm Dia close grain CI Dynamically balanced +- 2 Grms.	item33	1	NO
34	1.33	Pallet Mill Counter Pully SPC Section 9 Grove x 230 mm Dia close grain CI Dynamically balanced +- 2 Grms.	item34	1	NO
35	1.34	Die Bolt 20x50 mm High Tensile (Unbreako/ TVS/LPS	item35	100	Nos
36	1.35	Die Bolt 20x140 mm High Tensile (Unbreako/ TVS/LPS	item36	100	Nos
37	1.36	Die Bolt Washer (Spacer)	item37	200	Nos
38	1.37	Bush for “T” Shaft (Roller Holding Bush)	item38	2	Nos
39	1.38	Elevator Belt 10” 4 Ply	item39	100	Nos
40	1.39	Elevator MS Bucket 8*5, 3 Hole	item40	300	Nos
41	1.4	Elevator Bucket Bolt(3*8, 1 1/2)	item41	900	Nos
42	1.41	Twin Rotor With Motor 10 HP Complete	item42	1	NO
43	1.42	Fidder Condisnior Soft Complite SS 2 Mtr.	item43	2	NO
44	1.43	Sprocket Duplex 1\" 10 Teeth	item44	12	NO
45	1.44	Sprocket Duplex 1\" 14 Teeth	item45	12	NO
46	1.45	Sprocket Duplex 1\" 18 Teeth	item46	12	NO
47	1.46	Sprocket Duplex 1\" 19 Teeth	item47	12	NO
48	1.47	Sprocket Duplex 1\" 25 Teeth	item48	6	NO
49	1.48	Sprokit Duplex ¾\" 14 Teeth	item49	12	NO
50	1.49	Sprocket Duplex ¾\" 95 Teeth	item50	2	NO
51	1.5	Sprocket Duplex 1\" 50 Teeth	item51	2	NO
52	1.51	Side Glass 200 MM PVC Round	item52	12	NO
53	1.52	Vindish charger 3 HP Motor With Gair Box Complete	item53	2	NO
54	1.53	Elevator Botom Drum Complete With Bearing 4mm seet	item54	2	NO
55	1.54	Pellet Mill Hopper SS Make	item55	1	NO
56	1.55	Betch Selector Switch 15 Motor	item56	1	NO
57	1.56	Pellet Bin SS Make 4 MM Seet 6 M.T.	item57	1	NO
58	1.57	Pellet Mill Cover SS 5 MM Seet with Gard Complete	item58	1	NO
59	1.58	Molases Pump 4\" With Flench Complete	item59	1	NO
60	1.59	Molases Pump 2\" With Flench Complete	item60	1	NO
61	1.6	Hammer Mill Beater size 140 x 60 x 6 mm thick	item61	200	Nos
62	1.61	Hammer Mill Sieve 5 mm Hole perforation size about 880 x 720 x 3 mm thick	item62	10	Nos
63	1.62	Hammer Mill Beater Holding Rod 18 mm Dia	item63	24	Nos
64	1.63	Hammer Mill Beater Spacing Bush	item64	200	Nos
65	1.64	Elevator Top Drum about 600 mm Dia x 300 mm width complete with shaft about 800 mm length x 50mm Dia suitable for Bearing 1211 K	item65	4	Nos
66	1.65	SS 304 Wire Mesh For Vibro 5MM OPG x 1.50 MM Dia Size 72” x 72”	item66	2	Nos
67	1.66	Chain Conveyor Chain size 285	item67	50	Mtr
68	1.67	Chain Conveyor Chain size 385	item68	100	Mtr
69	1.68	Chain Conveyor Spocket 9 teeth with shoft 50 mmx600 mm	item69	4	NO
70	1.69	Chain 1\" simplex	item70	15	Mtr
71	1.7	Elivator Jacket 300x290 mm	item71	20	NO
72	1.71	Pelet Cooler Blower Empeler S.S with soft and bearing	item72	1	NO
73	1.72	T-Shaft Gun Metal Bush	item73	2	NO
74	1.73	150 HP Motor Bes Frem	item74	1	NO
75	1.74	Slate Conveyor Chain	item75	50	Mtr
76	1.75	Slate Conveyor Sprocket	item76	4	NO
77	1.76	Motor with Gair Box 5 HP-127 RPM PBL	item77	6	NO
78	1.77	Motor 3 HP- 80 RPM PBL	item78	4	NO
79	1.78	Pully 14” 2 Group B Section	item79	6	NO
80	1.79	Pully 3” +4” 2 Group B Section	item80	6	NO
81	1.8	Sprokit 15 Theeth Duplex ¾	item81	6	NO
82	1.81	¾ Duplex Chain	item82	15	Mtr
83	1.82	Duplex Chain 1\" Roller	item83	50	Mtr
84	1.83	Joot Seprator	item84	2	NO
85	1.84	Pellet Cooler Assentric	item85	1	NO
86	1.85	Pellet Sheev Jaali 6 mm SS	item86	3	NO
87	1.86	Chain Conveyor Roll	item87	100	Mtr
88	2	NAME OF THE ITEM FOR MANGLIA
89	2.01	Pallet Mill die 8mm hole Super Senior extra wide Size: 630 mm OD 520mm ID 222 mm Phase, 17 Rows of Holes with straight caller & m-20x12 holes both sides on 565 PCD	item89	15	Nos
90	2.02	Roller Shells “V” grooved for above Size 250mm OD 180mm ID(Suitable for Bearing no. 32220, 182 mm wide	item90	70	Nos
91	2.03	Roller Assembly Complete with shell & Bearing etc. Bearing NBC	item91	4	Nos
92	2.04	Die Holder Assembly Complete with “T” Shaft, Bearings 32324 & 32224, Bearing covers, Oil Seals etc. Bearing NBC	item92	1	No
93	2.05	Die Holder only (Alloy Steel Forging)	item93	1	No
94	2.06	“T” Shaft with centralized greasing system	item94	1	No
95	2.07	i) Eccentric Shaft (Alloy Steel) (Spare for Roller Assembly)	item95	4	Nos
96	2.08	ii) Middle Spacer 51 mm wide (Spare for Roller Assembly)	item96	4	Nos
97	2.09	iii) Bearing Cover Plate (Spare for Roller Assembly)	item97	24	Nos
98	2.1	iv) Bearing Pressing Plate (Spare for Roller Assembly)	item98	24	Nos
99	2.11	v) Circlip 180 mm Inner (Spare for Roller Assembly)	item99	60	Nos
100	2.12	vi) Lock nut for Eccentric Shaft m-20 (Spare for Roller Assembly)	item100	20	Nos
101	2.13	vii) Lock Nut Washer for above MB-20 (Spare for Roller Assembly)	item101	20	Nos
102	2.14	viii) Clamping Device (Setting Ring of male female rings) (Spare for Roller Assembly)	item102	20	Nos
103	2.15	ix) Centre Bolt for roller Alen Type (Unbreako/ TVS) (Spare for Roller Assembly)	item103	20	Nos
104	2.16	x) Nut for Centre Bolt Attached with 1 male ring & Pin (Spare for Roller Assembly)	item104	20	Nos
105	2.17	Front scraper assembly	item105	2	Nos
106	2.18	Stud for front scraper assembly	item106	24	Nos
107	2.19	Roller locking Assembly with Two Disc and master plate	item107	4	Nos
108	2.2	Share Pin Block	item108	2	Nos
109	2.21	Share Pin 18 mm Dia	item109	500	Nos
110	2.22	Paddles for conditioner of 330 mm die of SS-304 with Stud and Nut	item110	100	Nos
111	2.23	Die Ring rear for Straight collar die (Alloy Steel EN-9)	item111	1	No
112	2.24	Die Ring front for Straight collar die (Alloy Steel EN-9)	item112	1	NO
113	2.25	Die cover with 4 Hooks size 520 OD x 340 mm ID x 130 mm wide made of SS 304 x 3 mm thick plate SS-304	item113	4	Nos
114	2.26	Main Bearing cover Plate front with Oil Seal 180-150-13 for Bearing 32324	item114	2	Nos
115	2.27	Main Bearing cover Plate Rear with Oil Seal 170-150-13 for Bearing 32224	item115	2	Nos
116	2.28	Main Bearing No. 32324 NBC for Pellet Machine Die Holder	item116	2	Nos
117	2.29	Main Bearing No. 32224 NBC for Pellet Machine Die Holder	item117	2	Nos
118	2.3	F- 100 Tyre coupling Complete Fenner make	item118	2	Nos
119	2.31	Magnet Flat type for Pellet Machine Both Site	item119	2	Nos
120	2.32	Roller Shell Bearing No. 32220 NBC	item120	10	Nos
121	2.33	Main Bearing Pressing Ring front	item121	2	Nos
122	2.34	Main Bearing Pressing Ring rear	item122	2	Nos
123	2.35	Pallet Die Guard Assembly with Pallet cutter made of 6 mm thick SS 304 Plate	item123	1	Nos
124	2.36	Feeder Complete with screw about 02 Meter long 400 mm Dia	item124	1	No
125	2.37	Pallet Mill Main Pulley SPC Section 9 Grove x 1220 mm Dia close grain CI Dynamically balanced +- 2 Grms.	item125	1	No
126	2.38	Pallet Mill Counter Pulley SPC Section 9 Grove x 230 mm Dia close grain CI Dynamically balanced +- 2 Grms.	item126	1	NO
127	2.39	Die Bolt 20x50 mm High Tensile (Unbreako/ TVS)	item127	100	Nos
128	2.4	Die Bolt 20x140 mm High Tensile (Unbreako/ TVS)	item128	100	Nos
129	2.41	Die Bolt Washer (Spacer)	item129	100	Nos
130	2.42	Bush for “T” Shaft (Roller Holding Bush)	item130	2	Nos
131	2.43	Pellet mill (JU) Door with Duct having magnet, Moc. 55304	item131	1	Nos
132	2.44	Conveyor railing M.S. plate 20mm x 14 mm x 10 feet x 16 Pcs	item132	160	Feet
133	2.45	Cutter (Knife) Pallet Machine	item133	4	Nos
134	2.46	Pellet Mill Cover S.S. 5mm Sheet with Guard Complete	item134	1	Nos
135	2.47	Molasses Rotary Gear Pump 1” X 1”	item135	1	Nos
136	2.48	Chain Conveyor Chain Size 285 (Spares for Conveyor)	item136	50	Mtr.
137	2.49	Chain Conveyor Chain Size 385 (Spares for Conveyor)	item137	50	Mtr.
138	2.5	Chain 1” Simplex (Spares for Conveyor)	item138	15	Mtr.
139	2.51	Slate Conveyor Chain (Spares for Conveyor)	item139	50	Mtr.
140	2.52	Pellet Cooler Blower Impellor S.S (Spares for Conveyor)	item140	1	NO
141	2.53	Slate Conveyor Chain (Spares for Conveyor)	item141	20	Mtr.
142	2.54	Slate Conveyor Sprocket (Spares for Conveyor)	item142	2	NO
143	2.55	Motor with Gear Box 5 HP-127 RPM PBL (Spares for Conveyor)	item143	2	NO
144	2.56	Pulley 14” 2 Group B Section (Spares for Conveyor)	item144	2	NO
145	2.57	Pulley 3” 2 Group B Section (Spares for Conveyor)	item145	2	NO
146	2.58	Pulley 4” 2 Group B Section (Spares for Conveyor)	item146	2	NO
147	2.59	Jute Separator (Spares for Conveyor)	item147	1	NO
148	2.6	Chain Sprocket 1” x 17 Teeth Simplex(Spares for Conveyor)	item148	10	Nos
149	2.61	Chain Sprocket 1” x 18 Teeth Simplex(Spares for Conveyor)	item149	4	Nos
150	2.62	Chain Sprocket 1” x 19 Teeth Simplex(Spares for Conveyor)	item150	10	Nos
151	2.63	Hammer Mill Beater size 140 x 60 x 6 mm thick (Spares for Hammer Mill)	item151	60	Nos
152	2.64	Hammer Mill Sieve 5 mm Hole perforation size about 880 x 720 x 3 mm thick (Spares for Hammer Mill)	item152	10	NO
153	2.65	Hammer Mill Beater Holding Rod 18 mm Dia (Spares for Hammer Mill)	item153	12	Nos
154	2.66	Hammer Mill Beater Spacing Bush (Spares for Hammer Mill)	item154	24	Nos
155	2.67	Elevator Top Drum about 600 mm Dia x 300 mm width complete with shaft about 800 mm length x 50mm Dia suitable for Bearing 1211 K 4MM Sheet (Spares for Elevator)	item155	2	Nos
156	2.68	Elevator MS Bucket 8*5, 3 Hole (Spares for Elevator)	item156	300	Nos
157	2.69	Elevator Bottom drum Complete with shaft suitable for bearing F-210 4mm sheet (Spares for Elevator)	item157	2	Nos
158	2.7	Elevator Bucket Bolt(3*8, 1 1/2) (Spares for Elevator)	item158	900	Nos
159	2.71	Elevator rubber Belt10\" 4 Ply (Spares for Elevator)	item159	100	Mtr.
160	2.72	72\" Jointing clamp S.S. (Spares for Vibro Screen)	item160	1	Set
161	2.73	72\" S.S. Screen fitting Frame (Spares for Vibro Screen)	item161	1	Nos
162	2.74	SS 304 Wire Mesh For Vibro 5MM OPG x 1.50 MM Dia Size 72” x 72” (Spares for Vibro Screen)	item162	4	Nos
163	3	NAME OF THE ITEM FOR BANDOL
164	3.01	Feed Plummer Block with Bearing UCT-210	item163	2	Nos
165	3.02	Discharge Plummer Block with Bearing UCF-210	item164	2	Nos
166	3.03	Chain 150 Width	item165	10	Mtr
167	3.04	Sprocket- 125 mm Pitch x 6 Teeth	item166	2	Nos
168	3.05	Oil Seal- 55 dia x 70 diax 10thk.	item167	20	Set
169	3.06	Intake Bacth chain conveyor Gear Motor 5 HP, RPM-1450, RHS Box	item168	1	Set
170	3.07	Pedestal Bearing for Driving pulley SNA-509-1209K + H 209	item169	2	Nos
171	3.08	Bearing for Bottom UCT-208	item170	4	Nos
172	3.09	Bucket 6\"	item171	2	Nos
173	3.1	Bucket fasteners 5/16' x 1-1/4' long	item172	4	Nos
174	3.11	Drive Sprocket - 1 \" Pitch x 18 teeth	item173	2	Nos
175	3.12	Driven Sporcot -1 \"Pitch x 18 teeth	item174	2	Nos
176	3.13	Driving Chain	item175	1	Set
177	3.14	Belt 8\" wide 3 ply Nylon, 3mm top, 1.5mm bottom thickness food grade	item176	76	Mtr
178	3.15	Bearing 22316k + H22316	item177	4	Nos
179	3.16	Beaters M Type	item178	48	Nos
180	3.17	Distance Bush	item179	48	Nos
181	3.18	Sieves 6 mm Dia Hole/ 3 mm thk.MS	item180	1	Set
182	3.19	Vibration Dampers Anti Vibration Dampers Super Mount PS5-3D	item181	2	Nos
183	3.2	HRC 180 rubber spider	item182	10	Nos
184	3.21	Air cylinder Kit 1218K + H218	item183	1	Nos
185	3.22	Main Bearing - 1218K + H218 & 2218K + H318	item184	2	Nos
186	3.23	Plummer Block SNA-518	item185	2	Nos
187	3.24	Bearing for flap UCF-210	item186	2	Nos
188	3.25	Chain 1-1/2'' Pitch Simplex	item187	10	Mtr
189	3.26	Limit Switch 10A – 500 V	item188	2	Nos
190	3.27	Beaters 50 X 10mm THK. SS304 (PADDLE TYPE MOLASSES MIXER)	item189	1	Set
191	3.28	Main Bearing UCF-209, UCF-210 (PADDLE TYPE MOLASSES MIXER)	item190	1	Set
192	3.29	Oil Seals (PADDLE TYPE MOLASSES MIXER)	item191	1	Set
193	3.3	Solenoid Valve (PADDLE TYPE MOLASSES MIXER)	item192	1	Nos
194	3.31	Main Drive Belt (Set of 9) SPC -4750 (SENIOR PELLET MILL PS 420)	item193	2	Set
195	3.32	Main Bearing 32224 (SENIOR PELLET MILL PS 420)	item194	2	Set
196	3.33	Oil Seal 170 OD x 140 ID x 12 (SENIOR PELLET MILL PS 420)	item195	2	Nos
197	3.34	Shear Pin (SENIOR PELLET MILL PS 420)	item196	2	Nos
198	3.35	Die Fixing Bolts (SENIOR PELLET MILL PS 420)	item197	8	Nos
199	3.36	Front Die Cover Fixing Bolts ¾ X 21/2 ‘’ Half thrad (SENIOR PELLET MILL PS 420)	item198	8	Nos
200	3.37	Front Die Cover ¾’’ X 2’’(SENIOR PELLET MILL PS 420)	item199	1	Nos
201	3.38	Limit Switch 10A – 500 V (SENIOR PELLET MILL PS 420)	item200	1	Nos
202	3.39	Wearing Ring (SENIOR PELLET MILL PS 420)	item201	1	Nos
203	3.4	Wearing Ring Fixing Bolts (SENIOR PELLET MILL PS 420)	item202	8	Nos
204	3.41	Rear Scraper (SENIOR PELLET MILL PS 420)	item203	1	Nos
205	3.42	Dial Thermometer PT-100 (SENIOR PELLET MILL PS 420)	item204	1	Nos
206	3.43	Feeder Conditioner drive bolts (Set of 2 no.) (SENIOR PELLET MILL PS 420)	item205	1	Set
207	3.44	Die Holder (SENIOR PELLET MILL PS 420)	item206	1	Nos
208	3.45	Roller Holder Shaft (SENIOR PELLET MILL PS 420)	item207	1	Nos
209	3.46	Press Roll Assembly (SENIOR PELLET MILL PS 420)	item208	2	Nos
210	3.47	Press Roll shell 145Ø X 215Ø X 125mm LONG (20Kg) (SENIOR PELLET MILL PS 420)	item209	15	Nos
211	3.48	Eccentric shaft 105Ø X 255mm LONG (17.5Kg) (SENIOR PELLET MILL PS 420)	item210	4	Nos
212	3.49	Bearing Cover 100Ø X 155 X 25mm Thk. (SENIOR PELLET MILL PS 420)	item211	4	Nos
213	3.5	Distance Ring (SENIOR PELLET MILL PS 420)	item212	2	Nos
214	3.51	Packing Plate (SENIOR PELLET MILL PS 420)	item213	4	Nos
215	3.52	Packing Ring (SENIOR PELLET MILL PS 420)	item214	4	Nos
216	3.53	Clamping Nut 75Ø X 135Ø X 20mm Thk. (SENIOR PELLET MILL PS 420)	item215	10	Nos
217	3.54	Bolt Special 36Ø X 290mm Long (SENIOR PELLET MILL PS 420)	item216	10	Nos
218	3.55	Clamping device (outer & inner) (SENIOR PELLET MILL PS 420)	item217	4	Nos
219	3.56	Bearing 32217 (SENIOR PELLET MILL PS 420)	item218	4	Nos
220	3.57	Feeder Conditioner Screw (SENIOR PELLET MILL PS 420)	item219	1	Nos
221	3.58	Feeder Conditioner Bearing 6203ZZ (SENIOR PELLET MILL PS 420)	item220	2	Nos
222	3.59	Magnet (SENIOR PELLET MILL PS 420)	item221	4	Nos
223	3.6	Front Scraper Assembly (SENIOR PELLET MILL PS 420)	item222	1	Nos
224	3.61	Main Body Bushes (SENIOR PELLET MILL PS 420)	item223	2	Nos
225	3.62	Cutting Knife (SENIOR PELLET MILL PS 420)	item224	2	Nos
226	3.63	Die 8 MM Dia (SENIOR PELLET MILL PS 420)	item225	8	Nos
227	3.64	Nylon Bush for airlock size 22/19 ( 35 dia x 45 dia x 28 thk) (SS ROTARY AIR LOCK)	item226	10	Nos
228	3.65	Bearing for Eccentric Shaft 2218 (COUNTER FLOW PELLET COOLER)	item227	2	Nos
229	3.66	Spring - 45 OD x 37 ID x 100 mm long (COUNTER FLOW PELLET COOLER)	item228	4	Nos
230	3.67	Rotary level indicator (COUNTER FLOW PELLET COOLER)	item229	1	Nos
231	3.68	Bearing on top tray 6205 zz (COUNTER FLOW PELLET COOLER)	item230	10	Nos
232	3.69	Cooler feeder gear motor HP-01, RPM-1420, KW-0.75, VFL RHS Box EFF1 motor (COUNTER FLOW PELLET COOLER)	item231	1	Nos
233	3.7	Springs (COUNTER FLOW PELLET COOLER)	item232	10	Nos
234	3.71	Set of sieve (COUNTER FLOW PELLET COOLER)	item233	2	Nos
235	3.72	Vibratory Motor 2HP, RPM 1440, KW-1.50, 415 Volt (COUNTER FLOW PELLET COOLER)	item234	1	Nos
236	3.73	Filter bags Ø150 X 2060mm Long (ASPIRATION UNIT FOR HAMMER MILL)	item235	16	Bags
237	3.74	Clamps (ASPIRATION UNIT FOR HAMMER MILL)	item236	16	Nos
238	3.75	Sequential Timer (ASPIRATION UNIT FOR HAMMER MILL)	item237	1	Nos
239	3.76	Solenoid Valve 1.5” Dia (ASPIRATION UNIT FOR HAMMER MILL)	item238	2	Nos
240	3.77	Metal Wheels 125mm pitch X 6 teeth X 250 mm PCD X 15mm thk.(SLAT CONVEROR)	item239	1	Nos
241	3.78	Circlip (SLAT CONVEROR)	item240	60	Nos
242	3.79	Chain 75 mm pitch (SLAT CONVEROR)	item241	5	Mtr
243	3.8	Drive Sprocket - 1 \" P x 68 teeth Simplex (SLAT CONVEROR)	item242	2	Nos
244	3.81	Driven Sprocket - 1 \" P x 14 teeth Simplex (SLAT CONVEROR)	item243	2	Nos
245	3.82	Drive Chain 1\" Pitch (SLAT CONVEROR)	item244	2	Nos
246	3.83	Bearing UCF- 210, UCT - 210 (SLAT CONVEROR)	item245	10	Nos
247	4	NAME OF THE ITEM FOR SAGAR
248	4.01	Coupling : F-110 Fenner make rubbe F-110 Fenner make rubber Tyre couple	item246	4	Nos
249	4.02	“V” belt SPC-4750	item247	35	Nos
250	4.03	Die 8 mm Tapper caller	item248	4	Nos
251	4.04	Shear pin	item249	100	Nos
252	4.05	Limit switch device	item250	40	Nos
253	4.06	Pulley on machine 1200 mm dia 11 groove SPC section	item251	1	Nos
254	4.07	Oil seal Front bearing 170x200x15/13	item252	2	Nos
255	4.08	Lock pin or circlip of roller	item253	30	Nos
256	4.09	Alen key holder bolt	item254	30	Nos
257	4.1	Die ring	item255	2	Nos
258	4.11	Scraper	item256	6	Nos
259	4.12	Chuck nut of main shaft	item257	10	Nos
260	4.13	Oil seal Rear bearing 140x170x15/13	item258	2	No
261	4.14	Main bearing cover plate (front & rear)	item259	2	Nos
262	4.15	Main motor pulley 225 mm dia 11 groove SPC section	item260	1	Nos
263	4.16	Conditioner Drive Chain coupling 6018	item261	2	Nos
264	4.17	Die hoist ARM 6010 zz	item262	2	Nos
265	4.18	Door hinge bearings 6206 zz	item263	4	Nos
266	4.19	Counter shaft bearing block S -618	item264	2	Nos
267	4.2	Press roll assembly 32220	item265	10	Nos
268	4.21	Main bearing Front-NU-328	item266	2	No
269	4.22	Counter shaft 22318k+H 2318	item267	2	Nos
270	4.23	Front die cover	item268	2	No
271	4.24	Chuck nut of Roller	item269	30	No
272	4.25	Acrylic Glass 200 dia x 200nt. (For seght glass )	item270	4	No
273	4.26	Hammer Spacer Bush set	item271	4	Nos
274	4.27	Coupling F-100 rubber type couple	item272	2	Nos
275	4.28	Main bearings 22319 K	item273	2	Nos
276	4.29	Sleeves H-2319	item274	2	Nos
277	4.3	Main Bearings UCF-208	item275	2	Nos
278	4.31	Permananent Magnet 500X200mm	item276	4	Nos
279	4.32	Hammer EN-42 Number of hammers 72 nos, overall Dimension of beaters 142x63x8mm	item277	3	Nos
280	4.33	Sieve Thickness 2.5mm, Screen size 1475x675mm, Mesh width 4 mm	item278	2	Set
281	4.34	Vibration Dampers VBPGS-2D polybond make	item279	6	Nos
282	4.35	Drive End bearing UCF, F-208	item280	2	Nos
283	4.36	Drive End bearing F-208	item281	2	Nos
284	4.37	Coupling Chain coupling ‘ 1’pitch, 22 teeth simplex chain	item282	1	Nos
285	4.38	Gear Box PBL, Model M-062232 BGCH 1-1-5A	item283	1	Nos
286	4.39	Coupling F-60 Tyre Type	item284	10	Nos
287	4.4	Air cylinder 50 dia 150 stroke double acting pneumatic cylinder	item285	2	Nos
288	4.41	Main bearing 1216K	item286	2	Nos
289	4.42	Sleeve H316K	item287	2	Nos
290	4.43	Pedestal S 516	item288	2	Nos
291	4.44	Wood slats Seasoned wood Slat dimension 550x80x30	item289	40	Nos
292	4.45	Bolts for fitting the slats	item290	40	Nos
293	4.46	Chain for the conveyor	item291	40	Nos
294	4.47	Gear Box Elecon, Model 1044293	item292	1	Nos
295	4.48	Motor Siemens, Model E 0708/505840211004, 1.5 K / 2 HP	item293	1	Nos
296	4.49	Coupling size F-70	item294	2	Nos
297	4.5	Drive end bearings SKF ,UKF-209	item295	2	Nos
298	4.51	Shaft end bearings SKF ,UKP-209	item296	2	Nos
299	4.52	Rotor Shaft Material : End Dia: 40mm Pin rods: MS 10mm dia	item297	1	Nos
300	4.53	Gear Box Bongfiglioli, AS30 PP90	item298	1	Nos
301	4.54	Elevator Bucket 8” -2 Bolt bucket	item299	200	Nos
302	4.55	Belt Solivator 500	item300	1000	Nos
303	4.56	Coupling Direct coupling (size 6018 – Dia 48/Dia45)	item301	1	Nos
304	4.57	Driven Section Bearing UCF, SKF, F-208	item302	2	Nos
305	4.58	Gear Box COUPLING Bongfiglioli, AS45-PP112, 6018 (Dia 48/Dia45)	item303	1	Nos
306	4.59	Bottom liner Plate UHMWPE 10mm	item304	2	Nos
307	4.6	Chain cleaning device Brush	item305	6	Nos
308	4.61	Wear rail TiscRal or eqivalent material	item306	12	Nos
309	4.62	Side Plate thickness H.R. IS 2062, 5mm, 4mm	item307	5	Nos
310	4.63	Bottom plateThickness H.R. iS 2062, 5mm	item308	5	Nos
311	4.64	Bottom wear plate thickness UHMW 10mm	item309	5	Nos
312	4.65	Top Plate Thickness 3mm	item310	5	Nos
313	4.66	Sprocket 4” pitch, 7 teeth, 65 Dia.	item311	20	Nos
314	4.67	Drive section Bearing UCF-NTN UCF-212	item312	1	Nos
315	4.68	Driven section Bearing UCF-NTN (UCF-208)	item313	1	Nos
316	4.69	Gear Box Coupling 6018 (Dia 58/Dia 60)	item314	2	Nos
317	4.7	Magnet unit SS 304, Min. 6000 Gauss Swing type with pneumatic cylinder	item315	4	Nos
318	4.71	Main screw pipe Heavy duty ‘c’ class MS ERW pipe, Dia 76- c class	item316	2	Nos
319	4.72	Drive end bearing SKF, Flange Type ball bearing-FY510	item317	2	Nos
320	4.73	Drive shaft bearing EN 24	item318	2	Nos
321	4.74	Driven end bearing FY 510 SKF	item319	2	Nos
322	4.75	Gear Box Bongfiglioli, AS45 PP 112	item320	2	Nos
323	4.76	Gear Box Coupling 5018 (Dia 48/Dia 45)	item321	2	Nos
324	4.77	Connector ¼”-8	item322	1	Nos
325	4.78	Solenoid valve MMFH-5-1/4 (Solinoid valve)	item323	4	Nos
326	4.79	Solenoid Coil MSFW/24-42-50/60 (Solenoid coil)	item324	2	Nos
327	4.8	SCREW Dischargers Eminence, SC-250, 1.53MX 08 Nos, 1.2MX 4 Nos, Screw Dia. 250 mm	item325	3	Nos
328	4.81	Main screw pipe Heavy duty ‘c’ class MS ERW pipe, Dia 76-C class	item326	2	Nos
329	4.82	Gear Box Bongfiglioli Model AS30PP90	item327	1	Nos
330	4.83	Gear Box Coupling 5016 (Dia 38/Dia 30)	item328	2	Nos
331	4.84	Drive shaft bearing EN24	item329	2	Nos
332	4.85	End bearing SKF, Flange type ball bearing-F208	item330	2	Nos
333	4.86	Coupling Type Simplex chain coupling	item331	2	Nos
334	4.87	Bearing F-201 TR Make	item332	2	Nos
335	4.88	Rotor Type Wane Type	item333	2	Nos
336	4.89	Gear Box PBL, M052236 BGCH 1-1-1A	item334	2	Nos
337	4.9	Signt Glass details for Airlock Dia- 250	item335	2	Nos
338	4.91	Gear Box- Airlock PBL, Model C042045/WGHJA	item336	1	Nos
339	4.92	Bearing TR, Bearing Model F-205	item337	2	Nos
340	4.93	Sieve Perforated, 2 decks	item338	1	Set
341	4.94	Pressure Switch Alfa, Model PR-9X, Range 2.5-9.5 kg/cm2	item339	2	Nos
342	4.95	Pneumatic cylinder Festo, Pneumatic cylinder specification DNC-125-160-PPV-A	item340	4	Nos
343	4.96	Pneumatic pipe 12 mm, Make of pipe janatics	item341	2	Nos
344	4.97	Connector ½”-12 mm	item342	2	Nos
345	4.98	Solenoid valve MFH-5-1/2	item343	4	Nos
346	4.99	Solenoid Coil MSFG/24-42 – 50/60	item344	2	Nos
347	5	Bottom liner Plate UHMWPE 10mm	item345	2	Nos
348	5.01	Wear rail Tiscral or equivalent	item346	2	Nos
349	5.02	Chain Drag bush chain type link – C45/En8D ‘Pin – 18 MnCr5/20MnCr6	item347	2	Nos
350	5.03	Drive Bearing UCF-NTN (UCF-212)	item348	2	Nos
351	5.04	S rocket 4 “pitch. 7 teeth 65 Dia	item349	2	Nos
352	5.05	Side plate thickness in mm H.R. IS 2062, 5mm, 4mm	item350	2	Nos
353	5.06	Bottom plate thickness H.R. IS 2062, 5mm	item351	2	Nos
354	5.07	Bottom wear plate thickness UHMW H.R. IS 2062, 5mm	item352	2	Nos
355	5.08	Top plate thickness in mm H.R. IS 2062, 3mm	item353	2	Nos
356	5.09	Intermediate plate thickness H.R. IS 2062 3mm	item354	2	Nos
357	5.1	Sprocket 4” pitch, 7 teeth, Dia. 65	item355	2	Nos
358	5.11	Driven Bearing UCF-NTN (UCF-208)	item356	2	Nos
359	5.12	Zero Speed sensor (3 Wire)	item357	2	Nos
360	5.13	Gear Box Bongfiglioli, Model AS 60 DPP112	item358	2	Nos
361	5.14	Coupling size 6018 (Dia 58/Dia 60)	item359	1	NO
362	5.15	Chain Drag bush chain type (Link – c45/En8D ; Pin – 18MnCr5/20MnCr6)	item360	2	Nos
363	5.16	Bottom liner Plate UHMWPE 10mm	item361	2	Nos
364	5.17	Wear rail TISCRAL or equivalent material	item362	2	Nos
365	5.18	Side plate thickness in mm H.R. IS 2062, 5mm, 4mm	item363	2	Nos
366	5.19	Bottom plate thickness H.R. IS 2062, 5mm	item364	2	Nos
367	5.2	Bottom wear plate thickness UHMW H.R. IS 2062, 10mm	item365	2	Nos
368	5.21	Top plate thickness in mm H.R. IS 2062, 3mm	item366	2	Nos
369	5.22	Intermediate plate thickness H.R. IS 2062, 4mm	item367	2	Nos
370	5.23	Sprocket 4” pitch, 7 teeth, Dia.65	item368	2	Nos
371	5.24	Gear Box Bongfiglioli, Model AS 60 DPP 112	item369	1	NO
372	5.25	Coupling size 6018 (Dia 58/Dia60)	item370	2	Nos
373	5.26	Main body plate ss-304, 4mm Thk	item371	50	Nos
374	5.27	Conditioner Paddle- ss-304, 6mm Thk	item372	50	Nos
375	5.28	Doors for cleaning ss-304, 4mm Thk	item373	50	Nos
376	5.29	Chain conveyor galls 30cm,19cm ¼30x19½	item374	30	Nos
377	5.3	Pellet sieve 6x4 Feat ¼180cm x 120 cm ½ (screen size)	item375	4	Nos
378	5.31	Perforated Sieve for Hammer Mill (FCS-100) (4mm perforation)	item376	2	Nos
379	5.32	Wire Mesh for pellet sieve 4 mesh	item377	1	Nos
380	5.33	Acrylic Glass 200 dia x 200 ht. 200 dia x 200 ht (for cyone glass)	item378	5	Nos
381	5.34	Hammer spacer bush set (20, 48& 58 mm long)	item379	5	Nos
382	5.35	SUS Front die cover ({pellet mill) (TC M 20 Bolt)	item380	1	Nos
383	5.36	SUSW SS End Cover (SS-304 construction)	item381	1	Nos
384	5.37	Roller Shells “V” grooved for above Size 250mm OD 180mm ID (Suitable for bearing no. 32220, 182mm wide	item382	10	Nos
385	6	NAME OF THE ITEM FOR SHIVPURI
386	6.01	Die 8mm (Alloy Steel)	item383	6	No
387	6.02	Press Roll Assembly (Gear Type)	item384	8	Nos
388	6.03	Die Holder Capsule Assemble with T Shaft	item385	1	Set
389	6.04	Die Holder Rear ring ( Chrome Inside)	item386	6	Nos
390	6.05	Die Holder Front ring ( Chrome Inside)	item387	6	Nos
391	6.06	Front Scapper Assemble	item388	2	Nos
392	6.07	Front Scapper Holding Stud	item389	2	Nos
393	6.08	Rear Scapper	item390	2	Nos
394	6.09	SS Angel Needle Valve	item391	1	Nos
395	6.1	Eccentric Shaft Gear Type	item392	4	Nos
396	6.11	Press Roll Shell	item393	10	Nos
397	6.12	Press Roll Cover	item394	6	Nos
398	6.13	Press Roll Sealing ring	item395	6	Nos
399	6.14	Press Roll middle ring	item396	6	Nos
400	6.15	Nut For Eccentric Shaft	item397	6	Nos
401	6.16	Die Holder Cover Front	item398	1	No
402	6.17	Die Holder Cover Rear	item399	1	No
403	6.18	T Shaft	item400	1	No
404	6.19	Shear Pin	item401	100	Nos
405	6.2	Counter Soft Pully With Shaft	item402	1	No
406	6.21	Main Motor Pully (9Groove, Dia. X9SPC)	item403	1	Nos
407	6.22	Conditional Drive	item404	2	Nos
408	6.23	V- Belt (SPC 5000)	item405	9	Nos
409	6.24	Fixing Gear For PRA	item406	4	Nos
410	6.25	Tyre Coupling F- 110 Dia 065 (18 X 4.4 ) Dia 075 (18 X 4.4 )	item407	2	Nos
411	6.26	M Type Beaters 140 X 50 X 6 (1 Set = 64 Nos.)(HAMMER MILL 75 HP)	item408	10	Sets
412	6.27	Perforated Sieve (1 set = 6 Nos.)(HAMMER MILL 75 HP)	item409	3	Sets
413	6.28	Beater Holding End Bush with Rod (HAMMER MILL 75 HP)	item410	18	Nos
414	6.29	Distane Bush (HAMMER MILL 75 HP)	item411	120	Nos
415	6.3	ALN KEY Bolt (8 mm) (HAMMER MILL 75 HP)	item412	120	Nos
416	6.31	Sieve Mounting Arrangement With Clamp (HAMMER MILL 75 HP)	item413	1	No
417	6.32	Tyre Coupling F- 110 Dia 055 (16 X 4.3 )Dia 065 (18 X 4.4 ) (HAMMER MILL 75 HP)	item414	2	Nos
418	6.33	Elevator Bucket (8\" 3 Bolt Bucket)	item415	40	Nos
419	6.34	Belt (10\" Width, 10mm Thickness)	item416	300	Mtr.
420	6.35	Back Stop	item417	3	Nos
421	6.36	Elevator Bottom Cage Type Drum With Shaft Assemble	item418	4	Nos
422	6.37	Elevator Top Cage Type Drum With Shaft Assemble	item419	4	Nos
423	6.38	Bottom Liner Plate (10 mm)	item420	2	Nos
424	6.39	Chain Cleaning Device (Brush)	item421	4	Nos
425	6.4	Wear Rail ( 8 X 20 mm)	item422	12	Nos
426	6.41	Wear Rail ( 10 X 60 mm)	item423	12	Nos
427	6.42	Side Pellet Thickness (5 mm, 4 mm)	item424	5	Nos
428	6.43	Bottom Plate Thickness (5 mm)	item425	5	Nos
429	6.44	Bottom Wear Plate Thickness (10 mm)	item426	5	Nos
430	6.45	Screw Conveyor Hanger Bearing (60 Dia.)	item427	10	Nos
431	6.46	Slate Conveyor Chain	item428	10	Mtr.
432	6.47	High level/ Low level Sensor For Bins Hopper (KV 5004 KV-3000-BPKG/NI)	item429	10	Nos
433	6.48	Air Cylinder Bor 63 X 300 For PN Side Gate With Seal Kit	item430	3	Nos
434	6.49	Air Cylinder Bor 40X 100 For Two Way FlapeWith Seal Kit	item431	3	Nos
435	6.5	Read Switch For Air Cylinder	item432	10	Nos
436	6.51	Solenoid Valve 1/4 \" BSP 5 Port	item433	2	Nos
437	6.52	Senser Proximity Type For Rotery Distubutors	item434	2	Nos
438	6.53	Gear Set For Pallet Mill Conditioner	item435	2	Nos
439	6.54	Rubber GasKet	item436	30	Mtr.
440	6.55	Air Cylinder Bor 150mm X 200mm Stroke	item437	2	Nos
441	6.56	CEE EM 45 Limit Switch (IP- 67)	item438	5	Nos
442	6.57	Bagging Limit Switch XCKJ.LC (CENLEC EN 50041 IP- 66)	item439	2	Nos
443	6.58	Pallet Coller Limit Switch BC 9	item440	2	Nos
444	6.59	Raddler Chain ( 125mm Pitch X 220 Wide)	item441	100	Mtr.
445	6.6	Drive Side Spocket 6 T X 125mm PitchBoth side Boss having Bore Key Way with Shaft Assembled	item442	3	Nos
446	6.61	Non Drive Side Spocket 6 T X 125mm Pitch Both side Boss having Bor Key Way with Shaft Assembled	item443	3	Nos
447	6.62	Circlip ( Roller assembly for 180 mm )	item444	5	Nos
448	6.63	End Bush ( Hammer mill for 8 mm )	item445	5	Nos
449	6.64	ASPIRATION UNIT FOR DUMP HOPPER (3 HP - NG90L - 2880 RPM - B5 TYPE)	item446	5	Nos
450	6.65	INTAKE CHAIN CONVEYOR ( 240 X 400 X 40M LG.) (10 HP - NG132ML - 1440 RPM - B5 TYPE)	item447	1	NO
451	6.66	CROSS CHAIN CONVEYOR ( 240 X 400 X 30M LG.) (7.5 HP - NG132S - 1440 RPM - B5 TYPE)	item448	1	NO
452	6.67	INTAKE ELEVATOR - 8\" (27M LG.) (7.5 HP - NG132S - 1440 RPM - B5 TYPE)	item449	1	NO
453	6.68	JUTE REMOVER - 250 X 500 (2 HP - NG90L - 1440 RPM - B5 TYPE)	item450	1	NO
454	6.69	CROSS SCREW CONVEYOR - (Ø305 X 305X 5.5 M LG.) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item451	1	NO
455	6.7	DISTRIBUTION SCREW CONVEYOR - (Ø305 X 305X 9 M LG.) (5 HP - NG112M - 1440 RPM - B5 TYPE)	item452	3	Nos
456	6.71	SCREW DISCHARGER - (Ø250 X 4.4M LG. & 4.8M LG.) - SET1 (5 HP - NG112M - 1440 RPM - B5 TYPE)	item453	4	Nos
457	6.72	SCREW DISCHARGER (Ø250 X 1.5, 1.8, 2.7 & 2.9M LG.) - SET2 (3 HP - NG100L - 1440 RPM - B5 TYPE)	item454	8	Nos
458	6.73	BATCH CHAIN CONVEYOR ( 240 X 400 X 5.8M LG.) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item455	1	NO
459	6.74	BATCH ELEVATOR - 8\" (12.1M LG.) (5 HP - NG112M - 1440 RPM - B5 TYPE)	item456	1	NO
460	6.75	ROTARY FEEDER FOR HAMMER MILL (1 HP - ELCEN MAKE - 1440 RPM - B5 TYPE)	item457	1	NO
461	6.76	HAMMER MILL - FCHM 7560 (60 HP - ND225M - 2880 RPM - B3 TYPE)	item458	1	NO
462	6.77	ASPIRATION UNIT FOR HAMMER MILL (5 HP - NG100L - 2880 RPM - B5 TYPE)	item459	1	NO
463	6.78	POWDER CHAIN CONVEYOR ( 240 X 400 X 5M LG.) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item460	1	NO
464	6.79	POWDER ELEVATOR - 8\" (15M LG.) (5 HP - NG112M - 1440 RPM - B5 TYPE)	item461	1	NO
465	6.8	BATCH MIXER - 1 TON (RIBBON TYPE) (20 HP - ND160L - 1440 RPM - B3 TYPE)	item462	1	NO
466	6.81	CHAIN CONVEYOR B.H.B.B.M ( 240 X 400 X 4M LG.) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item463	1	NO
467	6.82	MIX FEED ELEVATOR - 8\" (24.6M LG.) (7.5 HP - NG1325 - 1440 RPM - B5 TYPE)	item464	1	NO
468	6.83	FEEDER FOR PELLET MILL (5 HP - ELCENMAKE - 2880 RPM - B5 TYPE)	item465	1	NO
469	6.84	TWIN ROTOR MOLASSES MIXER -650X2000 LG. (15 HP - ND160M - 1440 RPM - B5 TYPE)	item466	1	NO
470	6.85	MOLASSES DOSING PUMP (3 HP - NG100L - 1440 RPM - B3 TYPE)	item467	1	NO
471	6.86	MOLASSES FEEDING PUMP / TRANSFER PUMP (2 HP - NG90L - 1440 RPM - B3 TYPE)	item468	1	NO
472	6.87	TWIN PADDLE CONDITIONER R-150x2000 (7.5 HP - NG1325L - 1440 RPM - B3 TYPE)	item469	1	NO
473	6.88	PELLET MILL - SUPER SENIOR (120 HP - ND280M - 1440 RPM - B5 TYPE)	item470	1	NO
474	6.89	INLET FEEDER FOR PELLET COOLER -1919 (1.5 HP - NG90S - 1440 RPM - B5 TYPE)	item471	1	NO
475	6.9	PELLET COOLER - 1919 (3 HP - ELCEN MAKE - 1440 RPM - B5 TYPE)	item472	1	NO
476	6.91	PELLET CHAIN CONVEYOR ( 240 X 400 X 4.5M LG.) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item473	1	NO
477	6.92	PELLET ELEVATOR - 8\" (18M LG.) (5 HP - NG112M - 1440 RPM - B5 TYPE)	item474	1	NO
478	6.93	PELLET COOLER BLOWER (25 HP - ND180M - 1440 RPM - B3 TYPE)	item475	1	NO
479	6.94	PC AIR LOCK - DIA 200 ( RICON MAKE ) (1 HP - NG80 - 1440 RPM - B5 TYPE)	item476	1	NO
480	6.95	SLAT CONVEYOR - 3\" (14 M) (3 HP - NG100L - 1440 RPM - B5 TYPE)	item477	1	NO
481	6.96	ASPIRATION SYSTEM - PW BINS (7.5 HP - NG1325 - 2880 RPM - B3 TYPE)	item478	1	NO
482	6.97	AIR LOCK - DIA 200 ( RICON MAKE ) (1 HP - NG80 - 1440 RPM - B5 TYPE)	item479	1	NO
483	6.98	ASPIRATION UNIT FOR ELEVATORS (1 HP - NG80 - 2880 RPM - B5 TYPE)	item480	5	Nos
484	6.99	AIR COMPRESSOR (20 HP - NG160L - 1440 RPM - B3 TYPE)	item481	1	Nos

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Madhya Pradesh Tenders

Machinery and Tools Tenders

Building Machinery Tenders

Earth Moving Machinery Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Supply Of Spare Parts Of Cattle Feed Plant Machinery, Cattle Feed Factory Pachama-Madhya Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Supply Of Spare Parts Of Cattle Feed Plant Machinery, Cattle Feed Factory Pachama-Madhya Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us