Public Health And Engineering Department has published Nit96 Providing Pipe Line Submersible Pumpset Work In Uwss Nimbahera. Submission Date for this Tender is 24-02-2021. Submersible Pump Tenders in nimbahera Rajasthan. Bidders can get complete Tender details and download the document.
| Name of Work: WORKS OF CONSTRUCTION & COMMISSIONING OF 4 NOS.TUBE WELLS, P,L&J OF RISING & DISTRIBUTION PIPE LINE, PROVIDING & INSTALLATION OF PUMPING SETS, ETC. AT UWSS NIMBAHERA DISTT. CHITTORGARH ON SINGLE POINT RESPONSIBILITY BASIS WITH ONE YEAR DEFECT LIABILITY PERIOD. | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Construction of Tube Well for 4 nos. | BI01010001010000000000000515BI0100001112 | ||
| 2 | 2 | Construction of Tube Well up to 100 mtr. depth in all type of rocks by DTH system & over burden to accommodate casing pipe of following sizes in all types of soil & over burden including lowering of casing pipe, (if required) excluding cost of casing pipe, as per IS:2800 Part 1: 1991 and IS:2800 Part II: 1979 (both amended upto date) and technical specifications. The work would be completed after obtaining sand free water. The tube well should have a through out bore as per nominal dia of casing pipe. | BI01010001010000000000000515BI0100001113 | ||
| 3 | 3 | Nominal bore 200 mm dia | BI01010001010000000000000515BI0100001114 | 640 | mtr. |
| 4 | 4 | Add 15% extra on above item for drilling depth beyond 100 mtr, if depth of tube well is more than 100 mtr. | BI01010001010000000000000515BI0100001115 | 240 | mtr. |
| 5 | 5 | Supply of ERW M.S. block casing pipe ISI marked (IS: 4270/1992) of grade Fe 410 of following sizes at site of work. | BI01010001010000000000000515BI0100001116 | ||
| 6 | 6 | 200 mm nominal bore | BI01010001010000000000000515BI0100001117 | 72 | mtr. |
| 7 | 7 | Supply & Fixing tube well cover of MS sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with GI Nipple 45cm long & two GI flanges at both ends in 80mm sizes passing through a hole in the centre of MS sheet. A 25 mm socket with end plug shall also be welded over top plate. A GI nipple having outside thread of size 1/2" (for installation pressure gauge) shall be provided & welded with 80mm GI nipple near top plate nipple shall be provided with end plug.(200 mm) | BI01010001010000000000000515BI0100001118 | 4 | Each |
| 8 | 8 | Prividing laying jointing of PIPELINE | BI01010001010000000000000515BI0100001119 | ||
| 9 | 9 | Providing, lowering, laying, aligning, fixing in position and jointing in tranches Ductile Iron (DI) ISI marked K-7 grade S&S pipes as per IS:8329:2000 (amended upto date), with internal cement mortar lining suitable for potable water with rubber ring (EPDM) joints as per IS:5382-1985 including all taxes (Central and local), transportation and freight charges, inspection charges, loading /unloading charges, stacking of pipes including cost of labour and materail, specials (Tee, bend etc.) satisfactory hydraulic testing, disinfection etc. complete as per technical specifications and direction of Engineer-in-charge.(excluding earth work), with execise Duty Exemtion.\nNote : providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately.\n | BI01010001010000000000000515BI0100001120 | ||
| 10 | 10 | A. 100 mm dia DI pipe line class - K-7 | BI01010001010000000000000515BI0100001121 | 2800 | RMT |
| 11 | 11 | Providing, lowering, aligning, fixing in position in pipe line at work site, DI D/F Resilient seated (soft seated) Sluice Valves (Gate Valves) , Vacuum tight(bubble tight), straight and pocket less body passage of approved make of following class & dia complete confirming to BS-EN-1171/ AWWA C-509 and of following specifications: Body & bonnet of Ductile cast iron of grade GGG40/GGG50 as per DIN 1693 or GR SG-400/12 as per IS 1865 or equivalent grade as per IS :3896-part2-1985 and subsequent revisions, Wedge of same material as body & shall vulcanised rubber lined with EPDM (food grade quality) and seals of NBR Face to face dimensions as per BS 5163-89/ IS 14846/2000 (amended up to date) /Din 3202 F4, Stem/ spindle of SS (AISI 316 or equivalent) Electrostatic epoxy powder(EP-P)/ Fusion bond epoxy ( Non-Toxic- suitable for drinking water) coated with minimum thickness of 250 microns inside and outside, Drilled as per IS 1538. Nut-Bolt confirming to IS:1363 and IS: 1367 (Galvanised steel) Insersion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC, Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge. Note: Rates are exclusive of tail piece/ dismantling joints and earth work. | BI01010001010000000000000515BI0100001122 | ||
| 12 | 12 | Manually Operated Resilient Seated Sluice Valves of Class PN 1.0/1.6 - 100 mm dia | BI01010001010000000000000515BI0100001123 | 10 | Each |
| 13 | 13 | Providing, lowering, aligning, fixing in position in pipe line, DI D/F resilient seated (soft seated) Swing type Non Return Valve of approved make of following Pressure rating & dia complete, generally confirming to IS: 5312 (part -1)/ 2004 (amended up to date) and of following specifications: Body, Bonnet & disc of Ductile cast iron of grade GGG40/GGG50 as per DIN 1693 or GR SG-400/12 as per IS 1865 or equivalent grade as per IS :3896-part2-1985 and subsequent revisions, Face to face dimensions as per IS 5312 (part -1):2004 Drilled as per IS:1538. Electrostatic Epoxy Powder(EP-P) / Fusion Bonded Epoxy (Non-Toxic & suitable for drinking water) coated with minimum thickness of 250 micron applied on body, cover and disc inside and outside . Disc seal ring of EPDM/ Neoprene (food grade quality) and disc seal retaining ring of SS/CS.Shaft of SS- AISI- 410, Hinge SS AISI 316/410 ,Bonnet Gasket EPDM ,Bush- Brass with EPDM/NBR "O" ring seal Nut-Bolt confirming to IS:1363 and IS: 1367 (galvanised steel) Insersion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC including jointing & jointing material, labour, testing and commissioning along with pipeline as per Technical Specification & as per direction of Engineer-in-charge. \nNote: Rates are exclusive of tail piece/ dismantling joints and earth work. | BI01010001010000000000000515BI0100001124 | ||
| 14 | 14 | Class PN 1.0/1.6, 100 mm dia. | BI01010001010000000000000515BI0100001125 | 4 | Each |
| 15 | 15 | Earthwork in excavation in foundation trenches or drains including dressing of sides & ramming of bottom lift up to 1.5 mtr including taking out the excavated soil & depositing & refilling of jhiri with watering & ramming and disposal of surplus excavated soil. | BI01010001010000000000000515BI0100001126 | ||
| 16 | 16 | A. All kind of soil | BI01010001010000000000000515BI0100001127 | 515 | Cum |
| 17 | 17 | B. Ordinary rock | BI01010001010000000000000515BI0100001128 | 460 | Cum |
| 18 | 18 | C. Hard rock (required blasting ) | BI01010001010000000000000515BI0100001129 | 465 | Cum |
| 19 | 19 | Dismantling of cement concrete pavement for pipe line and chambers by mechanical means using pneumatic tools, cutting the peripheral edge by CC cutter, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials up to a lead of 1000 meters. Measurement for dismantled trench to be made as per standard trench width specified in tender document and no extra payment shall be made for trench width more than specified, re-handling of material/earth to complete the tasks as per technical specification and scope of work. | BI01010001010000000000000515BI0100001130 | 205 | Cum |
| 20 | 20 | Providing and laying in position cement concrete in specified grade over prepared base course complete including finishing, curing, all material, labour, machinery, lighting, guarding for road restoration work in trenches of pipe line and chamber work. Measurement for CC work to be made as per standard trench width specified in tender document and no extra payment shall be made for trench width more than specified, complete work as per technical specification and scope of work. | BI01010001010000000000000515BI0100001131 | ||
| 21 | 21 | M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). | BI01010001010000000000000515BI0100001132 | 205 | Cum |
| 22 | 22 | Providing and installation of Submersible pumping sets | BI01010001010000000000000515BI0100001133 | ||
| 23 | 23 | Supply & Installation of 3 phase ISI marked submersible motor pump set of five star rating by BEE and as per JS: 8034-2011 (pump) and IS 9283-2013 (motor) or amended up to date of approved make of following duty condition with required accessories including making connection suitable for tube well/DCB. The job includes lowering of motor pump, installation of complete fitting & accessories, jointing of electrical cables up to switch board, testing of submersible pump set and interconnection up to water mains, complete in all respect. | BI01010001010000000000000515BI0100001134 | ||
| 24 | 24 | 9.3 KW (12.5 HP) & head above 120 mtr. | BI01010001010000000000000515BI0100001135 | 158.1 | KW |
| 25 | 25 | Supply & Fixing of ISi marked three core PVC flat submersible cable as per IS 694: 1990 or amended up to date and conductor as per class 5 of IS 8 130: 1980 includ ing making connection etc. | BI01010001010000000000000515BI0100001136 | ||
| 26 | 26 | 3 core 4.0 Sq.mm | BI01010001010000000000000515BI0100001137 | 1200 | RMT |
| 27 | 27 | Supply and Fixing of electric control feeder panel comprising of suitable rating MCCB , fully automatic star-delta starter, over load relay, ampere meter with CTs, volt meter, phase preventor, suitable starting capacitors, phase indicators, lighting arrangement etc complete suitable for three phase pump set. The panel should have space for energy meter (supplied by DISCOM). All these equipments shall be housed by panel box made out from 18 guage M.S. Sheet with powder coating. Panel should be of minimum size 900 x 600 x 450 mm with Stand ( made of angle iron of size 35x35x5mm) duly bolted/screwed with enclosure box having 4 legs, each leg's length 18" and double door including in built locking system. The legs should be embedded in M-15 cement concrete plat form.The size of CC plateform should be equal or bigger than the base size of panel of CC plateform should be equal or bigger than the base size of panel having height of at least 200 mm from ground level. The panel should have opening of suitable size in front of space for energy meter with glass for meter reading. The operation of panel should be suitable for on 440 Volt AC Supply. | BI01010001010000000000000515BI0100001138 | ||
| 28 | 28 | Above 10 HP and up to 15 HP | BI01010001010000000000000515BI0100001139 | 4 | Each |
| 29 | 29 | Providing & Lowering in tubewell ISl marked GI Pipe "B" (medium) class as per IS: 1239 part I 2004 or amended up to date threaded and double flanged (welded) on both ends and two number 25x3 mm flat welded on both ends between pipe & flange, rubber washer & nut bolts etc. complete in all respect. | BI01010001010000000000000515BI0100001140 | ||
| 30 | 30 | 50 mm dia | BI01010001010000000000000515BI0100001141 | 600 | RMT |
| 31 | 31 | Supplying & Fixing MS clamp set of 50X6 mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of sumbersible pump sets. | BI01010001010000000000000515BI0100001142 | 8 | Each |
| 32 | 32 | Supply & Fixing XLPE insulated / P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor Armoured of IS:7098-I/1554-1 approved make in ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick under layer of sand, second Class bricks covering, refilling earth, compaction of earth, making necessary connection, testing etc. as required of size. | BI01010001010000000000000515BI0100001143 | ||
| 33 | 33 | 10.0 Sq.mm, 4 core | BI01010001010000000000000515BI0100001144 | 200 | RMT |
| 34 | 34 | Providing and installation of Monoblock pumping sets | BI01010001010000000000000515BI0100001145 | ||
| 35 | 35 | Providing, installation, testing and commissioning of Centrifugal Monoblock pump set conforming to IS 9079 operating at sync. speed 2900 RPM with requisite MOC impeller, priming funnel, cock, suitable flanges at suction and delivery side. Pump shall have common shaft for pump and motor. Motor shall be suitable for working on 415 V ± 10%, 3 Ph, 50 Hz A.C. Supply. Motor shall be TEFC type and Pump set shall be suitable for working at various discharge and head requirements as per scope of work. Pump shall be erected on C.C. foundation / cross channels / RSJ frame block with suitable foundation bolts grouted in C.C. foundation block etc. complete in all respect as per specification, scope of work and direction of Engineer in Charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by Technical Committee. | BI01010001010000000000000515BI0100001146 | ||
| 36 | 36 | Centrifugal Monoblock Pump set (Single Stage)20.0 HP | BI01010001010000000000000515BI0100001147 | 2 | Each |
| 37 | 37 | Providing, installation, testing and commissioning of submersible monoblock pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph, 50 Hz AC and with water lubricated bearing to accept entire hydraulic thrust. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer's design. Antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. complete in all respect as per specification, scope of work and direction of Engineer in Charge of following power rating, suitable for prescribed duty conditions of one of the makes approved by Technical Committee. | BI01010001010000000000000515BI0100001148 | ||
| 38 | 38 | 12.5 HP | BI01010001010000000000000515BI0100001149 | 2 | Each |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
