Tender For Civil, Mechanical And Electrical Works In Jammu Plains And Kashmir Valley Under Jammu And Kashmir Retail Ro -Surface dressing of the ground including removing small plants, bushes ,vegetation (dia less than 4) and making surface levelled and disposal of rubbish outside HPCLs premises to an unobjectionable place, as directed by the Engineer in Charge. , Excavation for foundation upto required depth below ground level in any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, foundation, trenches/plinth beam etc compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCLs premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete . The measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths.EXCAVATION IN EARTH BETWEEN 1.5 TO 3 M, Providing and laying 50 mm thick DPC in 1:2:4 mix with 6 to 12 mm size aggregate and water proofing compound of approved make as per manufacturer specification, Providing and laying in position specified grade (Ready Mix Concrete) controlled concrete as per approved mix design for sub-structure (i.e. upto ground level icluding pavement ) and shapes using graded metal with size 20 mm and 12.5 mm. including placing, vibrating, compacting, curing etc. complete as per provisions of the relevant IS codes Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item READY MIX CONCRETE (M-30) FOR FOOTNG / COLUMNS / BEAMS / ROOF SLAB as per IS-4926, Providing and laying dry trap rubble stone soling 230 mm thick including hand packing, filling the interstices with chips, spalls and binding with grit and selected murrum, watering, compacting by power rolling with 8/10 ton roller complete., Supplying & Fixing M25 grade precast concrete poles for fencing with 6mm stirrups welded to four 8MM main vertical reinforcement Size of pole 6.0 length with bottom section 3X4 & top section 3X3 erecting, placing, grouting in proper line , levelled & painting of the pole with two coats of Acrylic emulsion paint exterior grade over a coat of cement primer etc. completed as per the instruction of Eng. In-Charge(Refer attached Drawing)., Supplying, laying, joining and aligning RCC Hume pipes conforming to IS-458 Latest Edition below approach road as directed. Rate to include joining with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4 haunching @ 1m c/c , also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the HUME Pipe for pulling cables in future.Test certificates from manufacture shall be submitted and approved by EIC before use HUME PIPES- 150 MM DIA NP2 CLASS , Providing and laying integral cement based water proofing of average 100 mm thick as per specifications given below:- cleaning RCC slab and applying two coats of polymer bases Elastometric coating Brush Bond RFX of Fosroc/approved equivalent in SIKA .- providing and laying brickbat coba in CM 1:4 mixed with water proofing compound and curing for a period of 24 hours.-Laying of 20mm thick plastering with 1:4 mixed with Conflast X 421C of Fosroc @125 per bag of cement or approved equivalent in SIKA finishing smooth with neat cement , making half round chamfering at the junction of parapet wall and slab , laying of 12mm thick pressed burnt clay tile( approved by HPCL) with 1:4 Cement mortar and curing for 10 days . The above job to be carried under supervision by reputed water proofing agencies or by authorised applicator.Contractor will be required to submit a guarantee in respect of performance of waterproofing for 10 years on stamp-paper. In addition to this, an amount equal to 10% of cost of waterproofing items shall be retained as retention money for 2 years from the date of completion, which shall be returned only after successful completion of this period., Supply, installation and fixing of Prefabricated MS grill (IS 2062 Latest Edition) using MS flat/structurals / bars / hollow sections / strips / pipes etc as per design given by HPCL and direction of Engg.-In-Charge. Rate to include erection, grouting of posts in PCC 1:1.5:3, painting by two coats of red oxide primer and two coats of synthetic enamel of approved shade. Grouting PCC to be paid separately as per relevant item.(Refer attached Drawing) , ALUMINIUM PANELED DOOR : Providing and fixing Powder Coated aluminum section of approved colour having coating thickness of minimum 50 micron & minimum wall thickness of not less than 2 mm, joints mitred and jointed with heavy duty aluminium pressure die cast cleats with fins to match the outer frames and door frames conforming JINDAL sections as specified fully paneled with 9 mm thick pre-laminated 3 layers medium density ( exterior grade) particle board Grade-1, type -II conforming to IS:12823 bonded with phenolformaldehyde synthetic resin of approved brand and manufacturer fixed to shutter with aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC/neoprene felt/polysulphide sealant/silicon sealant including hard ware such as tower bolt of 150 mm length from inside and Aluminum handle and Aluminum aldrop of 200 mm length. on both sides, 3 nos. Aluminium hinges of 100 mm length etc all complete as per architectural drawing. Aluminium door section of JINDAL make or equivalent make with the following section : Main frame on all sides - 4700 (20102) -101.6 x 44.45 x 2.5 of weight 1.977 kg/m Shutter vertical frame- 4537 - (19516) 53.7x44.45x2.3 of weight 1.238 kg/m. Shutter top frame - 4540 - (19518) 53.7x44.45x2.3 of weight 1.173 kg/m. Shutter middle frame - 4621 (20014) - 49.91x44.45x3 of weight 1.495 kg/m Shutter bottom frame - 4524 -(19508) 83.5x44.45x3 of weight 2.107 kg/m, aluminium Cast Door handle and Clip - 4420 (19360) - 19x17.3x0.9 of weight 0.124 kg/m. In case of non-availability, approved equivalent make for Al sections is HINDALCO. Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next higher dimensions and weight per running metre without extra cost, EUROPEAN TYPE Supplying and fixing Pastel Colour wall mounted vitreous china European type water closet comprising of the following accessories including cutting and making good the walls & floors wherever required complete as directed by Engg.-In-Charge, having following (A) Pastel Colour vitreous china European water closet with P or S trap of approved make having integral matching conceled cistern supplied as part of the closet with all mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of Engg.-In-Charge.(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge (C) 15 mm NB CP brss inlet connection with Brass unions at the ends. (D) Approved make matching colour polypropylene seat cover with necessary brass hinges and rubber bushes etc (E) WC connector with neoprene rubber etc, SS GRAB BAR (A) and (B):Fabricating and fixing S. S. Railing with 40 mm dia MS Piperail & using 10X10 MS bar welded to Balaster ( diagonal pieces) and 20 x 20 MS Baluster as per the drawing. (GRAB BAR A &B).The item includes fabrication, buffing of the railing upto req. finish, fixing the railing at position with m20 grade concrete, finising the SURFACE properly etc. complete(Refer attached Drawing) , Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable conforming to IS 4985:2000/ IS 15328 : 2003/ IS 13592 : 1992 Type B/ BS 4514/ BS EN 1329, latest edition including all necessary fittings conforming to IS 14735 : 1999/ BS 4514/ BS EN 1329, latest edition and other accessories including connections etc., complete as per drawings or as directed at site.20MM , Providing and laying point wiring in concealed conduits for the following points using specified 1100V grade PVC insulated, FRLS multistranded 3 x 1.5 sqmm copper conductor wires. Rate to include supplying, laying and securing in position in roof slabs and brick walls or concrete columns 25 mm dia rigid PVC conduits (Conforming to IS 9537:Part 3: 1983) of approved make with necessary accessories and junction boxes/pull boxes.Providing and fixing in the brick walls flush type metal switch boxes of approved make shade and sufficient size to accommodate all 6A Modular switches / 3 pin socket, screws, holders. ceiling roses and the fan regulator wherever required. Rate to include wall chasing and rough plastering.Providing and fixing of approved MK or ANCHOR ROMA/HAVELLS /FINOLEX/CRABTREE/SSK make and of approved colour . One switch shall be provided for each light and fan point.Rate also to include providing main circuit wiring from DB to switch boards with 2 runs of 2.5 sqmm copper wire and 1 run of 1.5 sqmm through PVC conduit. also All wires shall be conforming to IS 694:1990. but for 6A socket controlled by one 6A switch on the same lighting board but for 6A socket controlled by one 6A switch independently mounted including providing wiring with 3 runs of 1.5 sqmm PVC insulated copper wire through PVC conduit, > END TERMINATION End termination of following cable with double compression NFLP gland and crimping sockets 3.5CX95 SQMM AL CABLE END TER, Supply and installation of BAJAJ make Glass reinforced plastic conical UV protected Single arm pole- Flange type of 1000mm length and Height 6.0 meter with door opening with junction box mounting arrangement but exclusive of junction box, 20mm dia. threaded made to J shape and having 600 mm total length steel grade EN8 foundation bolts with nuts, templates and all complete as per approved drawing. Approved Equivalent Make - PHILIPSFoundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8 nos. 12mm dia. tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mm c/c as per approved drawing. This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above sorrounding ground/driveway level for 200 mm and have slant 63mm dia. PVC sleeve cast insitu foundation for cable entry as per the drawing. Rates to include excavation, PCC, RCC and reinforcement, etc. complete(Refer attached Drawing), WATER BOUND MACADUM Providing and laying WBM in 75 mm thick compacted thickness each using well graded stone aggregates of approved quality of 90 to 45 mm size with screening of 13.2 mm & less. Rate includes spreading metals, hand packing, filling the interstices with spalls, chips, and approved quality binder and rolling each layer with 8 to 10 MT power roller with simultaneous watering till the metal is bound by the water binder paste to achieve maximum compaction, finishing the surface to proper grade and level .Rate also to include carrying out the following tests on aggregates and test results to be submitted to EIC before use and shall meet following strength requirements.[LA Abrasion value : 40 % , Flakiness Index :15 %] -third layer of 75mm thick using 53 to 22.2 mm size stone aggregate with screening of 13.2 mm & less, Supplying & Laying 40MM Dia Heavy-duty C Class MS Steel ERW Welded P/L ( TATA/Zenith/JINDAL make) Conforming to IS 1239 (part I) - latest edition to the required slope & alignment with heavy duty MS fittings like elbows, sockets,unions , tees etc. including doping pipe line with 3 coats of Shalimastic HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof. The P/L which would laid aboveground shall be painted with two coats of synthetic enamel over two coats of Zinc Chromate primer of approved quality and shade. The pipeline shall be tested at a pressure of 5Kg / sqcm. Pipe dia as 80MM DIA, PIPE RAILING : SUPPLY AND FIXING OF 40 NB MEDIUM QUALITY MS PIPES(IS 1239 LATEST EDITION) FOR TOP AND BOTTOM RAILINGS TO ANGLE IRON POSTS FOR FIXING THE EDGES OF THE CHAIN LINK FENCING. RATE INCLUDES FABN, CUTTING, BENDING OF THE MS PIPE, SUPPLY AND FIXING OF MS CLAMPS AT EVERY POST, WITH NUTS AND BOLTS(ALL PROPER SIZED) AND PAINTING THE RAILING WITH TWO COATS OF ZINC PHOSPHATE PRIMER AND TWO COATS OF SYNTHETIC ENAMEL PAINT AFTER PROPER CLEANING /SCRAPPING . SHALIMAR/BERGER/ASIAN MAKE 1ST QUALITY ONLY.(REFER ATTACHED DRAWING), etc.
