Procurement Of Cots Items Required To Manufacture Of Gypsy With Motion Platform 1:1 Metallic Mockup Sml Qty 01 Nos, MCO, 515 ARMY BASE WORKSHOP, ULSOOR, BENGALURU-Karnataka

Procurement Of Cots Items Required To Manufacture Of Gypsy With Motion Platform 1:1 Metallic Mockup Sml Qty 01 Nos - 1 Ram - Model : Oem Specified, Dual-Channel Ddr3 1866 ( O.C ) / 1333 / 1066 Mhz 4Gb 2 Hard Disk - Interface Sata 6Gb / S, Cache 8Mb, Capacity 1Tb, Area Density ( Avg ) 329Gb / In2, Guaranteed Sectors 488, 397, 168, Spin Speed ( Rpm ) 7, 200 Rpm Average Latency 4.16Ms, Random Read Seek Time <8.5Ms, Random Write Seek Time <9.5Ms.- Segate. 3 Mother Board - Motherboard With Following Config: - - Intel Core I7, I5, I3processor Supported. - Microatx Form Factors - 1066 / 800 / 533 Mhz System Bus * Support For Ddr3 1333 / 1066 Mhz Dimms * Support For Up To 16 Gb Of System Memory, 8-Channel ( 5.1+ 2 Independent Multi-Streaming ) Audio Subsystem With Three Analog Audio Outputs Using The Realtek Alc888s* Audio Codec, * Up To Twelve Usb 2.0 Ports * Six Serial Ata 3.0 Gb / S Ports, With Two Ports Compatible With Esata Dongles * One Serial Port Header * One Parallel Port Header * One Back Panel Ps / 2 Connector * One Pci Express* 2.0 X 16 Bus Add-In Card Connector * Two Pci Express 2.0 X 1 Connectors * Three Pci Slots . Ps / 2 Port Supports Key Board And Mouse- With On Board / External Communincation Port ( Com Port ) For Rs-232 Communication / 4 Processor - Intel Processor Core I7 3.07 Ghz / 4 Mb / Lga1156 / 1333 5 Speaker 5.1 Inspire - Creative Inspire 5 :1. Approx - Speaker Power: 25W Rms Per Channel ( 4Channel ) . Sub Woofer Power 17W Rms. Frequency Response: 40 Hz ~ 20 Khz, S / N Ration : 80Db, Distortion :1 %, Satelite Speaker: ( Lxwxh ) 7Cmx8cmx18.3Cm. Sub Woofer:19Cmx19cmx19cm. Wired Remote Control :2Cmx6cmx3cm. Power 12V Ac 2.9Amp Adopter.Volume Control With On / Off Switch.Audio Cable From Computer To Sub Woofer. Extended Audio Cable ( Molded ) One End Male Connector And Other End Female Connector 15 Mtrs-Qty 4 And All Standard Accessories To Be Provided. 6 Smps - Model : Oem Certified ( Coolermaster / Corsair Etc ) ; 720 Watt Or More 7 Ups 3 Kva Line Interactive - Output Power Capacity 3000 Watts Max Configurable Power 3000 Watts Nominal Output Voltage 230V Output Voltage Note Configurable For 220 : 230 Or 240 Nominal Output Voltage Efficiency At Full Load 92% Output Voltage Distortion Less Than 3% Output Frequency ( Sync To Mains ) 50 / 60 Hz + / - 3 Hz User Adjustable + / - 0.1 Crest Factor 3 : 1 Waveform Type Sine Wave Output Connections ( 8 ) Iec 320 C13 ( 2 ) Iec 320 C19 ( 6 ) Iec Jumpers Bypass Internal Bypass ( Automatic And Manual ) Input Nominal Input Voltage 230V Input Frequency 50 / 60 Hz + / - 5 Hz ( Auto Sensing ) Input Connections Hard Wire 3-Wire Input Voltage Range For Main Operations 160 - 280V Input Voltage Adjustable Range For Mains Operation 100 - 280V Other Input Voltages 220, 240 Powerchute Personal Edition V2.0 For Windows 2000 & Xp ( Multi Language Support ) With Power Card. With 3 Pin Indian Sockets 8 8-Port Ethernet Switch - 8 Port 100Mbps Switch With: ( A ) 8 ( 100Mbps ) Nway Auto Mdi Ports ( B ) Ieee 802.3 And Ieee 802.3U Standards Supported ( C ) 8 Nway 100Mbps Auto Detect Ethernet / Fast Ethernet Ports. ( D ) Full Duplex For Each Ports. ( E ) Operating At Max Packet Filtering And Forwarding Rate ( F ) Store And Forward Of Packet Switching ( G ) 256 Kytes Buffer Memory Per Device ( H ) 8 K Mac Address Entries Per Device ( J ) Compact Design For Soho Applications, External Power Adapter ( K ) Comprehensive Led Indications For Ports Status Indication ( L ) 8 Built-In 100Base T Ports ( M ) Auto 100Dual-Speed Port Upto 200Mbps 9 Vga Multiplier 1:4 - 1:4 Vga Multiplier With Gain & Power On / Off Control Input 170-240V Ac 50Hz Single Phase Output Vga, Rgb Video Amp, Tech: Video Amp Ic Along With Solid State Booster Ckt, No. Of. Output : 4 Max, Connector : 15 Pin 3 Rows Vga D Connector Resolution 800 X 600, 1024 X 760 10 Lan Card - Specifications Standards • Ieee 802.3 10Base-T Ethernet, • Ieee 802.3U 100Base-Tx Fast Ethernet, • Ansi / Ieee 802.3 Nway Auto-Negotiation, • Ieee 802.3X Full Duplex Flow Control Support Network Data Transfer Rate , • Ethernet: 10Mbps ( Half-Duplex ) , • Ethernet: 20Mbps ( Full-Duplex ) , • Fast Ethernet: 100Mbps ( Half-Duplex ) , • Fast Ethernet: 200Mbps ( Full-Duplex ) , Features 11 23 Led Monitor ( Non Touch ) - 23 Led Monitor ( Non Touch ) 12 Dvd Drive - Drive Type Dvdrw, Drive Height 42Mm, Interface Serial-Ata, Drive Mounting Horizontal / Vertical, Buffer Memory 2Mb Automatic Ball Balancing System : A.B.S Dvd-R Write 22X, Read 16X 13 Graphics Accelerator Card Nvidia Gt 730. - Nvidia Geforce Gt730 Graphics Accelerator Card 4Gb Ram, 16X Pci Express / Morphics Ver 9.0, Support Dual Link Dvi 2560X1600 Resolution Display Outs Puts, And Dual Link Hdcp Capable, Open Gl 2.1 Support, Pci Express 2.0 Support 14 Laser Printer - Print Speed Black ( Normal, A4 ) Up To 14 Ppm, Print Speed Footnote, Speed Specification Per Industry Standard Testing Methodsstandard Memory, 2 Mb Embedded In Sip Package, 16K Bit Nvram; Maximum Memory, 2 Mb Embedded In Sip Package, 16 Kb Nvram, Processor Speed 266 Mhz, Print Quality Black ( Best ) , Up To 600 X 600 Dpi ( 1200 Dpi Effective Output ) ; Print Technology, Laser Duty Cycle ( Monthly, A4 ) , Up To 5000 Pages 15 Pci Card 2Xserial Port - * Ieee 1284 Printer Port Respectively * Support 32 Bit Pci Bus, Pci Specification 2.1 16 Force Feedback & Game Wheel - Model : Logitech G29 Or Higher With Shifter Module, Gas, Brake, And Clutch Pedmaturi Gpysy, Power Supply, Software Cd-Rom, User Documentation 17 Dvi / Vga Converter - Pc Vga & Dvi Converter With I / P Vga / Dvi To O / P Svga, Vga, Tv & Video Converter 18 Operating System Cd - Original Windows 7 Professinal Iso 32-64 Bit Service Pack1 19 Microsoft Office 2010 - Original Microsoft 2010 Consists Ms Access 20 Video Projector With 25 Mtr Power Cord - Display Technology : 0.55, 1Chip Dmt, Dlp. Resolution : Native Xga ( 1024X768 ) . Brightness 2500 Or Above. Contrast Ratio 2000:1 Zoom / Focus Manual Focus& Zoom Lens. Projection Lens F= 2.4-2.6. Throw Ratio 1.63-1.97. Picture Size 40-300 Inches Diagonal. Source Lamp 150W / 180W / 230W. Lamp Life ( Upto ) Hrs 4000. Pc Compatibility Resolution : 640X480-1024X768 ( Native ) 1280X1024 Compressed. Video Compatibility Nstc / Ntsc4.43 / Pal Includingpal-M, N / Secam / Pal-60Component Video:480I / P526 / P ( 625I ) , 720P, 750P, 1080I ( 1125I60 Hz ) 1080I ( 1125I50hz ) . Input Terminal Rgb: Mini D-Sub 15Pinx2video:Rcax1+S- ( L / R ) X1 Audio: Stereo Mini Jack ( 3.5Mm ) X1 Rca Jeck ( L / R ) X1. Out Put Terminmaturi Gpysy Rgb : Mini D Sub 15 Pinx1. Audio Tereo Mini Jeck ( 3.5Mm ) X1. Communication Terminal Rs-232C ( D-Sub 9Pin ) X1 , Usb Terminal For Page Up / Downx1. Audio Spk 2W Mono.Remode Unit Full Projector Control, Power Point Page Up / Down Via Usb Dimensions Wxhxd 331X1102x245 Mm. ( Excluding Height Adjestment ) . Power Requriedments Ac 100-240V, 50 / 60Hz. Fan Noise 29Dba. ( Cover 10Ftx8ft Screen Area With In 3-3.5 Mtr Distance ) , With Minimum 18 Months Warranty ( For A Projection Of Front -01 Nos And Rear -01 Nos 21 19 4U Rack Computer Chassis - 19 4U Rack Computers Chassis Ipc -611 Bp Bare Chassis 22 Allen Key ( 2, 3, 4, 5, 6, 7, 8, 9 Set Of 8 ) - Isi Standard 23 Automobile Oil Omd110 ( Ltr ) As Per Requirement - Oil Omd / Equivalent Commercial Grade 24 Bubble Sheet ( M ) - 2 Mtr Width 25 Corrugated Sheet ( M ) - 2 Mtr Width 26 Grease ( Kg ) As Per Sample - Commercial Grade 27 Hessian Cloth ( M ) - 2Mtr Width 28 Insulation Tape ( Roll ) - Wonder Tape 10 Mtr Roll Pvc 29 Log Book - 30 Nails 1 ( Kg ) - 1 Isi Standard 31 Nose Plier - Isi Standard 32 Packing Tape ( Roll ) - Adhesive Packing Tape 50Mm Width, 10 Mtrs Std Roll 33 Chir Wood Packingboxes / Crates - Wooden Boxes Required For Packing One Set Of Maturi Gpysy 1:2 Sml Are As Follows:- Dimension Packing ( L X W X H Inches ) 25 X 26 X 15 - 02 Nos 39.5 X 39.5 X 14 - 01 Nos 23 X 15 X 11 - 02 Nos 23 X 17 X 15 - 02 Nos I6 X 10 X 12 - 01 Nos 18 X 15 X 8 - 02 Nos 60 X 35 X 60 - 01 Nos 27 X 24 X 20 - 02 Nos 20 X 13 X 14 - 02 Nos 75 X 55 X 48 - 01 Nos 34 Paint Black / Oliver Green Spray Container ( 300 Gms ) - Quick Drying Lacquer Spray 100% Acrylic Automobiles Finishes 35 Screw Driver Set - Isi Brand , Set Of Five 36 Solder Soft ( 100 Gm Roll ) - Solder Soft With Core Of Non Corrosive Flux For Std Electronic Work 37 Spanner Open-Jaw 13 / 17 - Isi Standard 38 Spanner Open-Jaw 14 / 15 - Isi Standard 39 Spanner Open-Jaw 17 / 19 - Isi Standard 40 Technical Manual - 41 User Hand Book - 42 Log Book - 43 Welding Rod 3.15Mm ( Pkt ) - Mild Steel / Caster Iron Welding Rod 3.15Mm Dia Sangam 6013 44 Sewing Thread Roll ( As Per Sample ) - Modi / Isi Brand 45 Adjustable Spanner 24 - Isi Standard 46 10 Core Cable Unshielded ( M ) - Type Yy 6.3Mm Dia Strength 8.1 Kg 47 15 Pin D Shell Female Connector Complete With Dust Cover & Strain Relief - Contacts Accepts Wire Sizes In The Range 22 To 26 Awg., Type-15 Way Sockets, Stock No.485-984 48 15 Pin D Shell Male Connector Complete With Dust Cover & Strain Relief - Contacts Accepts Wire Sizes In The Range 22 To 26 Awg., Type-15 Way Plug, Stock No.485-940 49 15-Core Cable ( Gear Sensor Pcb To Interface Pcb ) With 15-Pin Male & Female D-Sub End Connectors ( 100 Cm Length ) - Cable : Type Yy 6.3Mm Dia Strength 8.1 Kg Connectors :Itt D Sheel Connector, 50 2 Core Power Cable ( M ) - Type Yy 6.3Mm Dia Strength 8.1 Kg 51 2 Pin Zelex Male & Female Connector With Pin - 3.96 Pitch Friction Lock Header 52 25 Core Cable Unshielded ( M ) - Screened 6.3Mm Dia 53 25-Pin D Shell Connector Female Complete With Dust Cover & Strain Relief - Itt D Sheel Connector 54 25-Pin D Shell Connector Male Complete With Dust Cover & Strain Relief - Itt D Sheel Connector 55 3 Core Power Cable 15 A ( M ) - H07-Rnf-2.5 Sq Mm Dia 56 3 Core Power Cable, 5A ( M ) - H07-Rnf-1.5 Sqmm Dia 57 3 Pin Automobile Connector - Panel Receptable 3 Way Female With Pins 58 3 Pin Male Bug Connector - 3.96Mm Pitch Friction Lock Header 59 9 Pin Automobile Connector Male & Female - Panel Receptable 9 Way With Pins Male And Female 60 9 Pin D Shell Female Connector Complete With Dust Cover & Strain Relief - Itt D Sheel Connector 61 9 Pin D Sub Male Connector Complete With Dust Cover & Strain Relief - Itt D Sheel Connector 62 Audio Cable For ( Headphone Socket In Driver Cabin To Audio Mux - 10 M Length ) - Flexible Audio Cable ( Benden 1503A ) ; Nominal O / D-1503A-3.68Mm, Nominal Capacitance Between Conductors-174 Pf / M, Part No-1503A ( Black ) 209-1222. With Out Supporting Connecter 63 Binding Wire - Size ( 2061.02 ) 1 / 26 , 92 Mtrs Roll 64 Computer Power Cord 230 V Ac, 5 A, 3 Mtr Length ( Nos ) With 3 Pin Pluge - H07-Rnf-1.5Mm Dia Best Quality 65 Gear Sensor Pcb - Make : ., Model . 811C, Specification : Inputs: Active Lo, 8 Nos, Outputs : 8 Nos, Through 9 Pin D Connectors, As Per Drg No A4 515 Tata / Mmj / Mgs 37699 66 Plc For Maruti Gypsy ( Micro Controller ) - Interface Pcb / Sdd Approved - Communicates Between The Cgi Computer And External Real Time Devices Through The Serial Port, Specification : 8 Bit Micro Controller ( Cy8c 366 ) With 01Xmaster Card And 02Xslave Card. Operating Voltage : 12Dc, Digital Inputs : 80, Digital Outputs: 20, Analog Inputs: 08, Analog Outputs:04, Ports: 02Xports Additional For Stepper Motor, Display Panel: 16X02 Lcd, Display Panel ( 8 Segmentg ) . Provision For Programming The Microcontroller. Serial And Socket Communciation Facility. 67 Lan Cable Cat 5E With Rj-45 End Connectors ( 10 M Length ) - Duplex Cable ( Cat 5E Utp+Cat 5E Utp ) , Nominal Od 10.5X5.5Mm , Radius-44Mm, Type; Utp, Stock No.-252-2136 68 Lan Cable Cat 5E With Rj-45 End Connectors ( 1.5 M Length ) - Duplex Cable ( Cat 5E Utp+Cat 5E Utp ) , Nominal Od 10.5X5.5Mm , Radius-44Mm, Type; Utp, Stock No.-252-2136 69 Lan Cable Cat 5E With Rj-45 End Connectors ( 2 M Length ) - Duplex Cable ( Cat 5E Utp+Cat 5E Utp ) , Nominal Od 10.5X5.5Mm , Radius-44Mm, Type; Utp, Stock No.-252-2136 70 Microswitch - Push Button Type 71 Premium Quality Lt Wire For Dashboard Wiring ( M ) - 2Mm Dia Lt Wire Of Different Color 72 Proximity Switch P Type - Inductive P Type 73 Sleeves Assorted ( Quantities And Types As Per Samples Expandable Dshell Sleeve Mtrs ) - 1.5Mm, 2Mm, 4Mm, 5Mm, 8Mm, 10Mm, 15Mm, 20Mm ) 74 Spike Buster Socket Board 4 Sockets, 15 A - Make : 4 Sockets, 15 A , 15 / 5A Multipin Socket, 5 Mtrs Cable , Isi Standard 75 Spike Buster Socket Board 6 Sockets, 6 A - Make : 6A With 10 Mtrs Cable, Isi Standard 76 Vga Cable With 15-Pin Male And Female End Connectors ( 2 M Length ) - 6.9Mmdia Extra Guard Multi Conductor 77 Vga Cable With 15-Pin Male To Male Connectors ( 3M Length ) - 6.9Mmdia Extra Guard Multi Conductor 78 Vga Cable With 15-Pin Male End Connectors ( 25 M Length ) - 6.9Mmdia Extra Guard Multi Conductor With Both End M / F Moulded Connectors For Projector 79 Dp To Vga Convertor - Display Port To Vga Convertor 80 Hdmi To Vga Converter - 81 Heat Sink Sleeve - 1Mm, 1.5Mm, 2Mm, 4 Mm & 8 Mm Each -02 Mtrs 82 Ecom Switch For Ups Connection - Ecom Switch 5 Amps Male And Female 83 Ecom Switch For Ups Connection - Ecom Switch 15 Amps Male And Female 84 Universal Adaptor For 3 Pin Plug - For 6 Apms 85 Dvr Cabin Assembly Maruti Gypsy With Intermediate Frame For Driver Cabin Original Mock Up - ( I ) Strengthened & Modified Original Mockup With Floor Base, Include Front And Rear Windshield, Both Side Doors With Glass; All Three Rear View Mirrors, All Original Controls, Dashpanel, Meters, Switches, Steering With Steering Rod, Combination Switch, Ignition Switch, Gear Lever Duly Modified As Per Requirements And Drawings, Coupling With Steering, Mounting Of Accelerator, Brake And Clutch Assembly And Coupling Them With Cable / Master Cylinder Assembly As Per Requirement; Required Physical Constraints, Mounting Brackets, Brackets For Proximity Switches, And Gear Lever As Per Requirement; Seats With Upholstry, All Matting Work And Movable Rails Modified For Sensor Fitment; Seat Belt With Microswitch At Base End; Handbrake Assembly With Two Microswitches At Fully Engaged And Released Positions; All Indictors, Headlamps, Wipers, Wiper Motor, And Necessary Brackets And Fixtures To Mount Components And Tie Wiring Harnesses As Per Requirement, Set Of Modified Instrument Panel As Look As Original ( Ii ) Dvr Cabin Assembly Maruti Gypsy With Driver Seat, Cmdr Seat & Crew Seat ( Full Seats ) , Front Glass, Rear Glass, Side Glass, Side Cdr Mirrror, Front Head Lights, Side Lights, Top Lights Safty Belts All Accessories And Fittings With Olive Green Colour & Rubber Mat And Opholustry Work , With All Original Fitting Of Accessories With Intermediate Frame As Per Requirement 86 Mounting Plate For Speaker With Bracket - As Per Requirement 87 Mounting Plate For Plc With Bracket - As Per Requirement 88 Mounting Plate For Spike Buster - As Per Requirement 89 Main Gear Box Of Maruti Gypsy 5 +1 Gear - Orginal Gear Box Modified For Gypsy Sml As Per Requirement 90 Mounting Bracket For Smps - As Per Requirement 91 Instructor Chair - Isi Standard 92 Instructor Station 1:1Gypsy - Ms With Black Powder Coated For All Sheet Metal And Buffed For Steel Of Size Approx 5 X 3 X4 Or Lesser; One End With Facility To Hold All Items For Two Pc ( Mother Board, Ram, Graphics Card, Smps, Cd / Dvd Writer, Etc ) With Proper Cable Routing And Illumination And The Other End For Support Along With Space For Holding Minimum 2 Paper Reams; Foldable Assembly For Steering Wheel And Controller Assembly; Slot To Hold Laser Printer Of Standard Size And Fix Key Board & Mouse, Splitter Etc; Space To Install Four Cooling Fans; Two 5 Slot Cable Managers At The Bottom Of The Station; Facility To Hold And Swivel Two 23” Monitors ( As Per Requirement ) With Four Fans ( As Per Drg No A0-515-Mgs-37500 ( 1-100 ) , A0-515-Mg ( Mp ) -0001 ( 1-100 ) & A0-515-Smg-37800 ( 1-69 ) With Keyboard Tray As Per Requirement 93 Universal Joint Assy With Coupling Male And Female - As Per Drg No A0-515-Maturi Gpysy-00001 ( 1-60 ) For Maturi Gpysy Smls 94 Mounting Stand Video Projector - Projector Mounting Stand With Height Adjustable Extension, Locking Arrangement A0-515-Maturi Gpysy-00001 ( 1-60 ) ) 95 Screen For Driver Front View - Approx 16 X 12 ;Specs : Rear Projection Seamless Dark Tin Fabric Washable Screen; High Contrast; 0.8 Gain; Islet On Border ) As Per Drg No A0-515-Mgs-37500 ( 1-100 ) , A0-515-Mg ( Mp ) -0001 ( 1-100 ) & A0-515-Smg-37800 ( 1-69 ) 96 Screen For Driver Rear View - Size : Approx 12 X 10 ;Specs : Front Projection Seamless Fabric Washable Screen; High Contrast; 1.0 Gain; Through Loop On Border ) As Per Drg No A0-515-Mgs-37500 ( 1-100 ) , A0-515-Mg ( Mp ) -0001 ( 1-100 ) & A0-515-Smg-37800 ( 1-69 ) 97 Front Screen Frame - Approx 18.6’ X 10 Curved Frame With 8’ Chord And 7’ Height; Black Powder Coated; Square Pipe Minimum 1.5” Thickness; Can Easily Be Disassembled In Two Or More Parts For Transportation; Should Have No Sharp Edges; Stable For Its Own Weight And Screen As Per Drg No A0-515-Mgs-37500 ( 1-100 ) , A0-515-Mg ( Mp ) -0001 ( 1-100 ) & A0-515-Smg-37800 ( 1-69 ) 98 Rear Screen Frame - Approx 12’ Width X 10’ Height Flat Frame; Black Powder Coated; Square / Round Pipe Minimum 1.5” Thickness; Can Easily Be Disassembled In Two Or More Parts For Transportation; Should Have No Sharp Edges; Stable For Its Own Weight And Screen As Per Drg No A0-515-Mmj ( Mp ) 0001 ( 1-100 ) , A0-515-Mgs-37500 ( 1-100 ) , A0-515-Mg ( Mp ) -0001 ( 1-100 ) & A0-515-Smg-37800 ( 1-69 ) 99 Set Of Assorted Fasteners Maturi Gpysy / Maturi Gpysy / M.Gypsy - Cheese Head Slotted Screw Size M6 / 40 Long With Nut And Double Washer Nos - 20 Cheese Head Slotted Screw Size M6 / 25 Long With Nut And Double Washer - Ns-20 Cheese Head Slotted Screw Size M6 / 10 Long With Nut And Double Washer Nos - 25 Cheese Head Slotted Screw Size M4 / 60 Long With Nut And Double Washer Nos - 20 Cheese Head Slotted Screw Size M4 / 50 Long With Nut And Double Washer - Nos -20 Cheese Head Slotted Screw Size M4 / 25 Long With Nut And Double Washer Nos - 20 Counter Sync Head Slotted Screw Size M4 / 15 Long ( Csk ) - Nos 20 Counter Sync Head Slotted Screw Size M5x50 Long ( Csk ) - Nos 20 Cheese Head Slotted Screw Ize M3 / 6 Long With Double Washer - Nos 20 Flat Washer ( Or Plain Washer ) Size M 8 - Nos 25 Hexagonal Head Nut And Bolt M8x30mm With Double Washer - Nos -20 Hexagonal Head Nut And Bolt M8x25mm With Double Washer - Nos -20 Hexagonal Head Nut And Bolt M8x40mm With Double Washer - Nos -20 Hexagonal Head Nut And Bolt M8x75mm With Double Washer- Nos -20 Cheese Head Nut And Screw M6x25mm With Double Washer- Nos -20 Hexagonal Head Nut And Bolt M10x45mm With Double Washer - Nos -20 Hexagonal Head Nut And Bolt M6x75mm With Double Washer - Nos - 05 Cheese Head Nut And Screw M6x50mm With Double Washer - Nos -20 Wooden Screw 25Mm - Nos -20 Cheese Head Nut And Screw M6x40mm With Double Washer - Nos -20 Hexagonal Head Nut And Bolt M3x20mm With Double Washer - Nos -20 Wooden Screw 5Mm- Nos -20 Reveted Head Screw With Nut M6- Nos -20 Hexagonal Head Nut And Bolt-M10x30mm With Double Washer Nos - 20 100 Manufacturers Lable Plate - 515 Army Base Wksp Manufacturer Plate, As Per Sample 101 Anchor Bolt - Size: 20 Mm Dia X 12 102 U Bolt - U Bolt For Coupling Maruti Gyspy To Intermedite Frame With Nut And Washer As Per Requirment 103 Cable Ties And Tie Bases ( 25Mm Packet Of 100 ) As Per Sample - Standard Cabel Ties, White Nylon With A Non-Release Ratchet Lock Action Suitabel For Binding Cable Or Componets, Size-99X2.5 Stock No.543-428 & Self Adhesive Fixing Clips ( Rb Fixing Clips, Type: Rb8 ( W-25Mm ) , Stock No-170-5346 104 Cable Ties And Tie Bases ( 50Mm Packet Of 100 ) As Per Sample - Standard Cabel Ties, White Nylon With A Non-Release Ratchet Lock Action Suitabel For Binding Cable Or Componets, Size-99X2.5 Stock No.543-428 & Self Adhesive Fixing Clips ( Rb Fixing Clips, Type: Rb8 ( W-50Mm ) , Stock No-170-5346 105 Spiral Pipe 1.5 Dia ( Flexible Conduct ) - Mtrls : Nylon Pa6, Thread: Pg36, Temp: -40 Deg To 120 Deg, 106 Spiral Pipe 1 Dia ( Flexible Conduct ) - Mtrls : Nylon Pa6, Thread: Pg36, Temp: -40 Deg To 120 Deg, 107 Instrument Panel ( Meter Panel Gypsy With Modified Air Pressure, Fuel Guage, Oil Pressure Guage, Speedometer, Amp Meter, Temperature Guage For Gypsy With Complete Wiring ) - Modified Instrument Pannel As Look As Original, Consisting Of Set Of Panel Indicators And Set Of Panel Switches Including , 1 ) Windscreen Wash Switch 2 ) Modified Gypsy 4X4 Gear Swich With Shifting Lever And Lever Knob 3 ) Tow Light Switch 4 ) Dash Board Lamp 5 ) Fuel Guage ( E-1 / 2-F ) 6 ) Oil Pressure Guage ( 0-10Bar ) , 7 ) Warning Indicators 8 ) Temperature Guage ( 40-120Degree C ) , 9 ) Speedo Meter ( 0-140Km / Hr ) 10 ) Air Pressure-1 ( 0-10Bar ) 11 ) Ammeter ( -30 To 30+Amp ) 12 ) Air Pressure - 2 ( 0-10Bar ) 13 ) Black Out Switch 14 ) Hazard Warning Switch 15 ) Fuel Gauge Change Over Switch 16 ) Fog Lamp Switch 17 ) Push Start Switch, 18 ) Ignition Switch 19 Flasher Unit 108 3 Dof Motion Platform - Make : Tah 3Dof Hydraulic ( I ) Payload : 700Kg; 3 Degree Of Freedom ( Pitch + / -15 Deg, Roll + / - 15 Deg, Heave + / - 100Mm ) ; Velocity + / - 15Deg / Sec + / - 150Mm / Sec; Acceleration + / - 200 Deg / Sec2, + / - 400Mm Deg / Sec2; Response Time Upto 80Msec; Closed Height 800Mm To 900Mm; Operating Height 1100Mm To 1200Mm; Max Height 1200Mm / Sdd Approved 109 Hydraulic Oil - Hydraulic Fluid Sho46

Refer document

INR 175000.0 /-

Refer document

Name of Work: PROCUREMENT OF COTS ITEMS REQUIRED TO MANUFACTURE OF GYPSY WITH MOTION PLATFORM 1:1 METALLIC MOCKUP SML QTY 01 NOS
	Sl. No.	Item Description	Item Code / Make	Quantity	Units
1	1	RAM - Model : OEM specified, Dual-channel DDR3 1866(O.C)/1333/1066 Mhz 4GB \n		5	Nos
2	2	Hard Disk - Interface SATA 6Gb/s,Cache 8MB,Capacity 1TB,Area density (avg) 329Gb/in2,Guaranteed Sectors 488,397,168,Spin Speed (RPM) 7,200 RPM\nAverage latency 4.16ms,Random read seek time <8.5ms,Random write seek time <9.5ms.- segate.\n		2	Nos
3	3	Mother board - motherboard with following config: -\n- Intel core i7,i5,i3Processor supported.\n- MicroATX form factors\n- 1066/800/533 Mhz System Bus\n * Support for DDR3 1333 /1066 MHz DIMMs\n * Support for up to 16 GB of system memory,8-channel (5.1+ 2 independent multi-streaming) audio subsystem with three analog audio outputs using the Realtek ALC888S* audio codec, * Up to twelve USB 2.0 ports\n * Six Serial ATA 3.0 Gb/s ports, with two ports compatible with eSATA dongles\n * One serial port header\n * One parallel port header\n * One back panel PS/2 connector\n * One PCI Express* 2.0 x 16 bus add-in card connector\n * Two PCI Express 2.0 x 1 connectors\n * Three PCI Slots\n . ps/2 port supports key board and mouse- with On board / external communincation port (COM PORT) for RS-232 communication/\n		2	Nos
4	4	Processor - Intel Processor Core i7 3.07 Ghz /4 MB / LGA1156 / 1333		2	Nos
5	5	Speaker 5.1 Inspire - Creative Inspire 5 :1. Approx - Speaker power: 25W RMS per channel (4channel). Sub woofer power 17W RMS. Frequency Response: 40 Hz ~ 20 KHz,S/N Ration : 80db,Distortion :1 %, Satelite speaker:(LxWxH) 7cmx8cmx18.3cm. Sub woofer:19cmx19cmx19cm. Wired remote control :2cmx6cmx3cm. Power 12v AC 2.9Amp adopter.Volume control with on/off switch.Audio cable from computer to sub woofer. extended audio cable (molded) one end male connector and other end female connector 15 mtrs-qty 4 and all standard accessories to be provided.		1	Nos
6	6	SMPS - Model : OEM certified (Coolermaster/Corsair etc); 720 Watt or more		4	Nos
7	7	UPS 3 KVA line interactive - Output Power Capacity 3000 Watts Max Configurable Power 3000 Watts Nominal Output Voltage 230V Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage Efficiency at Full Load 92% Output Voltage Distortion Less than 3% Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz user adjustable +/- 0.1 Crest Factor 3 : 1 Waveform Type Sine wave Output Connections (8) IEC 320 C13 (2) IEC 320 C19 (6) IEC Jumpers Bypass Internal Bypass (Automatic and Manual)\nInput Nominal Input Voltage 230V Input Frequency 50/60 Hz +/- 5 Hz (auto sensing) Input Connections Hard Wire 3-wire Input voltage range for main operations\n160 - 280V Input voltage adjustable range for mains operation 100 - 280V Other Input Voltages 220,240 PowerChute Personal Edition v2.0 for Windows 2000 & XP (Multi Language Support) with power card. With 3 Pin Indian Sockets		1	Nos
8	8	8-port Ethernet Switch - 8 Port 100Mbps Switch with:\n(a) 8 (100Mbps) Nway auto MDI ports\n(b) IEEE 802.3 and IEEE 802.3U standards supported\n(c ) 8 Nway 100Mbps auto detect Ethernet/fast ethernet ports.\n(d ) Full duplex for each ports.\n(e) Operating at max packet filtering and forwarding rate\n(f) store and forward of packet switching\n(g) 256 Kytes buffer memory per device \n(h) 8 K MAC address entries per device\n(j) Compact design for SOHO applications, external power adapter\n(k) Comprehensive LED indications for ports status indication \n(l) 8 built-in 100Base T ports \n(m) Auto 100Dual-speed port upto 200Mbps		1	Nos
9	9	VGA multiplier 1:4 - 1:4 VGA multiplier with gain & power ON/OFF control input 170-240v Ac 50Hz single phase output VGA,RGB VIDEO AMP,Tech: Video Amp IC along with solid state booster ckt,No. Of. Output : 4 Max,connector : 15 Pin 3 rows VGA d Connector Resolution 800 x 600, 1024 x 760		2	Nos
10	10	LAN Card - Specifications \nStandards \n• IEEE 802.3 10Base-T Ethernet,• IEEE 802.3u 100Base-TX Fast Ethernet,• ANSI/IEEE 802.3 Nway Auto-Negotiation,• IEEE 802.3x Full Duplex Flow Control Support\nNetwork Data Transfer Rate ,• Ethernet: 10Mbps (Half-duplex),• Ethernet: 20Mbps (Full-duplex),• Fast Ethernet: 100Mbps (Half-duplex),• Fast Ethernet: 200Mbps (Full-duplex),Features \n\n		1	Nos
11	11	23" LED Monitor (Non Touch) - 23" LED Monitor (Non Touch)		2	Nos
12	12	DVD Drive - Drive Type DVDRW,Drive Height 42mm,Interface Serial-ATA,DrIve Mounting Horizontal/vertical,Buffer Memory 2MB Automatic Ball Balancing System : A.B.S DVD-R Write 22X,Read 16X		1	Nos
13	13	Graphics Accelerator Card Nvidia GT 730. - NVIDIA GEForce GT730 graphics accelerator card 4GB RAM, 16x PCI Express/Morphics ver 9.0,support dual link Dvi 2560x1600 resolution display outs puts,and Dual link HDcp Capable,open Gl 2.1 support,PCI express 2.0 support		3	Nos
14	14	Laser printer - Print speed black (normal, A4) Up to 14 ppm,Print speed footnote, Speed specification per industry standard testing methodsStandard memory, 2 MB embedded in SIP package, 16k bit NVRAM; Maximum memory, 2 MB embedded in SIP package, 16 Kb NVRAM,Processor speed 266 MHz,Print quality black (best), Up to 600 x 600 dpi (1200 dpi effective output); Print technology, Laser Duty cycle (monthly, A4), Up to 5000 pages		1	Nos
15	15	PCI Card 2xSerial Port - * IEEE 1284 printer port respectively\n * Support 32 bit PCI Bus, PCI Specification 2.1 \n		3	Nos
16	16	Force Feedback & Game Wheel - Model : Logitech G29 or higher with Shifter module, Gas, brake, and clutch pedMaturi Gpysy, Power supply, Software CD-ROM, User documentation		3	Nos
17	17	DVI/VGA Converter - PC VGA & DVI Converter with I/P VGA/DVI to O/P SVGA, VGA, TV & Video converter		3	Nos
18	18	Operating System CD - Original Windows 7 Professinal ISO 32-64 bit service pack1		2	Nos
19	19	Microsoft Office 2010 - Original Microsoft 2010 consists MS Access		2	Nos
20	20	Video projector with 25 mtr power cord - Display technology : 0.55", 1chip DMT, DLP. Resolution : Native XGA (1024x768). Brightness 2500 or above. Contrast Ratio 2000:1 Zoom/focus Manual Focus& Zoom Lens. Projection Lens F= 2.4-2.6. Throw Ratio 1.63-1.97. Picture size 40-300 inches diagonal. Source Lamp 150W/180W/230W. Lamp life (upto) hrs 4000. PC compatibility Resolution : 640x480-1024x768 (Native)1280x1024 compressed. Video compatibility NSTC/NTSC4.43/PAL includingPAL-M,N/SECAM/PAL-60component Video:480i/p526/p(625i), 720p,750p,1080i(1125i60 Hz)1080i (1125i50Hz). Input Terminal RGB: Mini D-sub 15pinx2Video:RCAx1+S-(L/R)x1 Audio: Stereo mini jack (3.5mm) x1 RCA jeck (L/R)x1. out put TerminMaturi Gpysy RGB : Mini D Sub 15 pinx1. Audio tereo mini jeck (3.5mm)x1. Communication Terminal RS-232C (D-sub 9pin) x1 ,USB terminal for page UP/DOWNx1. Audio spk 2w mono.Remode Unit Full Projector control, power point page UP/Down via USB Dimensions WxHxD 331x1102x245 mm.(excluding height adjestment). Power requriedments AC 100-240V,50/60Hz. Fan Noise 29dBA. (cover 10ftx8ft screen area with in 3-3.5 mtr distance), With minimum 18 months warranty ( for a projection of Front -01 Nos and Rear -01 Nos		2	Nos
21	21	19" 4U rack computer chassis - 19" 4U rack computers chassis IPC -611 BP Bare chassis		2	Nos
22	22	Allen key (2,3,4,5,6,7,8,9 Set of 8) - ISI Standard		1	Set
23	23	Automobile oil OMD110 (ltr) as per requirement - Oil OMD / Equivalent commercial grade		1	Ltrs
24	24	Bubble sheet (m) - 2 mtr width		5	Mtrs
25	25	Corrugated sheet (m) - 2 Mtr width		5	Mtrs
26	26	Grease (kg) as per sample - commercial grade		1	Kgs
27	27	Hessian cloth (m) - 2mtr width		30	Mtrs
28	28	Insulation tape (roll) - Wonder tape 10 mtr roll PVC		4	Roll
29	29	Log book -		1	Nos
30	30	Nails 1" (kg) - 1" ISI Standard		1	Kgs
31	31	Nose plier - ISI Standard		1	Nos
32	32	Packing tape (roll) - Adhesive packing tape 50mm width, 10 mtrs std roll		4	Roll
33	33	Chir wood packingBoxes/ crates - Wooden Boxes required for packing one set of Maturi Gpysy 1:2 Sml are as follows:- Dimension Packing \n(L x W x H Inches) 25 x 26 x 15 - 02 Nos\n39.5 x 39.5 x 14 - 01 Nos\n23 x 15 x 11 - 02 Nos\n23 x 17 x 15 - 02 Nos\nI6 x 10 x 12 - 01 Nos\n18 x 15 x 8 - 02 Nos\n60 x 35 x 60 - 01 Nos\n27 x 24 x 20 - 02 Nos\n20 x 13 x 14 - 02 Nos \n75 x 55 x 48 - 01 Nos \n		1	Set
34	34	Paint black/Oliver green spray Container (300 gms) - Quick Drying Lacquer Spray 100% Acrylic Automobiles Finishes		1	Tin
35	35	Screw driver Set - ISI Brand , Set of Five		1	Nos
36	36	Solder soft (100 gm roll) - Solder soft with core of non corrosive flux for std electronic work		1	Roll
37	37	Spanner open-jaw 13/17 - ISI Standard		1	Nos
38	38	Spanner open-jaw 14/15 - ISI Standard		1	Nos
39	39	Spanner open-jaw 17/19 - ISI Standard		1	Nos
40	40	Technical manual -		1	Nos
41	41	User hand book -		1	Nos
42	42	Log Book -		1	Nos
43	43	Welding rod 3.15mm (pkt) - Mild steel/caster iron welding rod 3.15mm dia Sangam 6013		1	Pkt
44	44	Sewing thread roll (as per sample) - Modi/ISI Brand		1	Roll
45	45	Adjustable spanner 24" - ISI Standard		1	Nos
46	46	10 core cable unshielded (m) - Type YY 6.3mm dia strength 8.1 kg		5	Mtr
47	47	15 pin D shell female connector complete with dust cover & strain relief - Contacts accepts wire sizes in the range 22 to 26 awg., Type-15 way sockets, Stock No.485-984		4	Nos
48	48	15 pin D shell male connector complete with dust cover & strain relief - Contacts accepts wire sizes in the range 22 to 26 awg., Type-15 way plug, Stock No.485-940		4	Nos
49	49	15-core cable (Gear Sensor PCB to Interface PCB) with 15-pin male & female D-sub end connectors (100 cm length) - Cable : Type YY 6.3mm dia strength 8.1 kg Connectors :ITT D sheel connector,		2	Nos
50	50	2 core power cable (m) - Type YY 6.3mm dia strength 8.1 kg		10	Mtr
51	51	2 Pin zelex male & female connector with pin - 3.96 Pitch friction lock header		2	Nos
52	52	25 core cable unshielded (m) - Screened 6.3mm dia		6	Mtr
53	53	25-pin D shell connector female complete with dust cover & strain relief - ITT D sheel connector		4	Nos
54	54	25-pin D shell connector male complete with dust cover & strain relief - ITT D sheel connector		4	Nos
55	55	3 core power cable 15 A (m) - H07-RNF-2.5 sq mm dia		20	Mtr
56	56	3 core power cable, 5A (m) - H07-RNF-1.5 sqmm dia		15	Mtr
57	57	3 Pin automobile connector - Panel receptable 3 way Female with pins		2	Nos
58	58	3 pin male bug connector - 3.96mm pitch friction lock header		10	Nos
59	59	9 Pin automobile connector Male & Female - Panel receptable 9 way with pins Male and Female		2	Nos
60	60	9 pin D shell female connector complete with dust cover & strain relief - ITT D sheel connector		4	Nos
61	61	9 pin D sub male connector complete with dust cover & strain relief - ITT D sheel connector		4	Nos
62	62	Audio cable for (headphone socket in driver cabin to audio mux - 10 m length) - Flexible audio cable (Benden 1503A); Nominal O/D-1503A-3.68mm, Nominal capacitance between conductors-174 pF/m, Part No-1503A(Black) 209-1222. with out supporting connecter		6	Nos
63	63	Binding Wire - Size(2061.02) 1/26 , 92 Mtrs Roll		1	Roll
64	64	Computer power cord 230 V AC, 5 A, 3 mtr length (Nos) with 3 pin pluge - H07-RNF-1.5mm dia BEST Quality		8	Nos
65	65	Gear sensor PCB - Make : ., Model . 811C, Specification : Inputs: Active lo, 8 Nos, Outputs : 8 Nos, Through 9 Pin D Connectors, As per Drg No A4 515 TATA/MMJ/MGS 37699		2	Nos
66	66	PLC for Maruti Gypsy (Micro controller) - Interface PCB / SDD approved - Communicates between the CGI computer and external real time devices through the serial port, Specification : 8 Bit micro controller (CY8C 366) with 01xMaster card and 02xSlave Card. Operating Voltage : 12DC, Digital Inputs : 80, Digital Outputs: 20, Analog Inputs: 08, Analog Outputs:04, Ports: 02xports additional for stepper motor, Display panel: 16x02 LCD, Display panel (8 segmentg). Provision for programming the microcontroller. Serial and socket communciation facility.		2	Nos
67	67	LAN cable Cat 5E with RJ-45 end connectors (10 m length) - Duplex cable ( Cat 5e UTP+Cat 5e UTP), Nominal OD 10.5x5.5mm , Radius-44mm, Type; UTP, Stock No.-252-2136		2	Nos
68	68	LAN cable Cat 5E with RJ-45 end connectors (1.5 m length) - Duplex cable ( Cat 5e UTP+Cat 5e UTP), Nominal OD 10.5x5.5mm , Radius-44mm, Type; UTP, Stock No.-252-2136		2	Nos
69	69	LAN cable Cat 5E with RJ-45 end connectors (2 m length) - Duplex cable ( Cat 5e UTP+Cat 5e UTP), Nominal OD 10.5x5.5mm , Radius-44mm, Type; UTP, Stock No.-252-2136		3	Nos
70	70	Microswitch - Push button type		4	Nos
71	71	Premium quality LT wire for dashboard wiring (m) - 2mm dia LT wire of different color		20	Mtr
72	72	Proximity Switch P Type - Inductive P type		9	Nos
73	73	Sleeves assorted (quantities and types as per samples expandable D'Shell sleeve mtrs) - 1.5mm,2mm,4mm, 5mm, 8mm,10mm,15mm, 20mm)		20	Mtr
74	74	Spike buster socket board 4 sockets, 15 A - Make : 4 sockets, 15 A , 15/5A multipin socket, 5 Mtrs Cable , ISI Standard		3	Nos
75	75	Spike buster socket board 6 sockets, 6 A - Make : 6A with 10 mtrs Cable, ISI Standard		2	Nos
76	76	VGA cable with 15-pin male and female end connectors (2 m length) - 6.9mmdia extra guard multi conductor		3	Nos
77	77	VGA cable with 15-pin male to male connectors (3m length) - 6.9mmdia extra guard multi conductor		3	Nos
78	78	VGA cable with 15-pin male end connectors (25 m length) - 6.9mmdia extra guard multi conductor with both end M/F moulded connectors for Projector		3	Nos
79	79	DP to VGA Convertor - Display Port to VGA Convertor		3	Nos
80	80	HDMI to VGA converter -		2	Nos
81	81	Heat Sink Sleeve - 1mm, 1.5mm, 2mm, 4 mm & 8 mm each -02 Mtrs		10	Mtr
82	82	Ecom Switch for UPS Connection - Ecom switch 5 amps Male and female		4	Set
83	83	Ecom Switch for UPS Connection - Ecom switch 15 amps Male and female		4	Set
84	84	Universal Adaptor for 3 pin plug - for 6 Apms		6	Nos
85	85	DVR Cabin Assembly Maruti Gypsy with intermediate frame for Driver cabin Original Mock Up - (i) Strengthened & Modified original Mockup with floor base, include front and rear windshield, both side doors with glass; all three rear view mirrors, all original controls, dashpanel, meters, switches, steering with steering rod, combination switch, ignition switch, gear lever duly modified as per requirements and drawings, coupling with steering, mounting of accelerator, brake and clutch assembly and coupling them with cable / master cylinder assembly as per requirement; required physical constraints, mounting brackets, brackets for proximity switches, and gear lever as per requirement; seats with upholstry, all matting work and movable rails modified for sensor fitment; seat belt with microswitch at base end; handbrake assembly with two microswitches at fully engaged and released positions; all indictors, headlamps, wipers, wiper motor, and necessary brackets and fixtures to mount components and tie wiring harnesses as per requirement,Set of Modified instrument panel as look as Original\n\n(ii) DVR Cabin Assembly Maruti Gypsy with Driver Seat, Cmdr Seat & Crew Seat (Full seats),front glass,rear glass, side glass,side cdr mirrror, Front Head Lights, Side lights, Top Lights safty belts all accessories and fittings with olive green colour & rubber mat and opholustry work , with all Original fitting of accessories with intermediate frame as per requirement		1	Nos
86	86	Mounting Plate for Speaker with bracket - as per requirement		1	Nos
87	87	Mounting Plate for PLC with bracket - as per requirement		1	Nos
88	88	Mounting Plate for Spike Buster - as per requirement		1	Nos
89	89	Main Gear Box of Maruti Gypsy 5 +1 Gear - Orginal Gear box modified for Gypsy Sml as per requirement		1	Nos
90	90	Mounting Bracket for SMPS - as per requirement		1	Nos
91	91	Instructor chair - ISI Standard		1	Nos
92	92	Instructor station 1:1Gypsy - MS with Black powder coated for all sheet metal and buffed for steel of Size approx 5' x 3' x4' or lesser; One end with facility to hold all items for two PC (mother board, RAM, Graphics card, SMPS, CD/DVD writer, etc) with proper cable routing and illumination and the Other end for support along with space for holding minimum 2 paper reams; Foldable assembly for steering wheel and controller assembly; Slot to hold laser printer of standard size and fix Key Board & Mouse, splitter etc; Space to install four cooling fans; Two 5 slot cable managers at the bottom of the station; Facility to hold and swivel two 23” monitors (as per requirement) with four fans (as per Drg No A0-515-MGS-37500(1-100), A0-515-MG(MP)-0001(1-100) & A0-515-SMG-37800(1-69) with keyboard tray as per requirement		1	Nos
93	93	Universal joint assy with coupling male and female - as per Drg No A0-515-Maturi Gpysy-00001(1-60) for Maturi Gpysy Smls		1	Nos
94	94	Mounting stand video projector - Projector mounting stand with height adjustable extension, locking arrangement A0-515-Maturi Gpysy-00001(1-60))		2	Nos
95	95	Screen for Driver Front View - Approx 16' x 12' ;Specs : Rear Projection Seamless Dark Tin Fabric Washable Screen; High Contrast; 0.8 Gain; Islet on border) As per Drg No A0-515-MGS-37500(1-100), A0-515-MG(MP)-0001(1-100) & A0-515-SMG-37800(1-69)		1	Nos
96	96	Screen for Driver Rear View - Size : Approx 12' x 10' ;Specs : Front Projection Seamless Fabric Washable Screen; High Contrast; 1.0 Gain; Through loop on border) As per Drg No A0-515-MGS-37500(1-100), A0-515-MG(MP)-0001(1-100) & A0-515-SMG-37800(1-69)		1	Nos
97	97	Front Screen Frame - Approx 18.6’ x 10' curved frame with 8’ chord and 7’ height; Black powder coated; Square pipe minimum 1.5” thickness; Can easily be disassembled in two or more parts for transportation; Should have no sharp edges; Stable for its own weight and screen As per Drg No A0-515-MGS-37500(1-100), A0-515-MG(MP)-0001(1-100) & A0-515-SMG-37800(1-69)		1	Nos
98	98	Rear Screen Frame - Approx 12’ width x 10’ height Flat frame; Black powder coated; Square / Round pipe minimum 1.5” thickness; Can easily be disassembled in two or more parts for transportation; Should have no sharp edges; Stable for its own weight and screen As per Drg No A0-515-MMJ(MP)0001(1-100) , A0-515-MGS-37500(1-100), A0-515-MG(MP)-0001(1-100) & A0-515-SMG-37800(1-69)		1	Nos
99	99	Set of Assorted fasteners Maturi Gpysy/Maturi Gpysy/M.Gypsy - Cheese head slotted screw size M6/40 long with nut and double washer Nos - 20\nCheese head slotted screw size M6/25 long with nut and double washer - Ns-20\nCheese head slotted screw size M6/10 long with nut and double washer Nos - 25\nCheese head slotted screw size M4/60 long with nut and double washer Nos - 20\nCheese head slotted screw size M4/50 long with nut and double washer - Nos -20\nCheese head slotted screw size M4/25 long with nut and double washer Nos - 20\nCounter sync head slotted screw size M4/15 long (CSK) - Nos 20\nCounter sync head slotted screw Size M5x50 long (CSK) - Nos 20\nCheese head slotted screw ize M3/6 long with double washer - Nos 20\nFlat washer (or plain washer ) size M 8 - Nos 25\nHexagonal head nut and bolt M8x30mm with double washer - Nos -20\nHexagonal head nut and bolt M8x25mm with double washer - Nos -20\nHexagonal head nut and bolt M8x40mm with double washer - Nos -20\nHexagonal head nut and bolt M8x75mm with double washer- Nos -20\nCheese head Nut and screw M6x25mm with double washer- Nos -20\nHexagonal head nut and bolt M10x45mm with double washer - Nos -20\nHexagonal head nut and bolt M6x75mm with double washer - Nos - 05\nCheese head Nut and screw M6x50mm with double washer - Nos -20\nWooden screw 25mm - Nos -20\nCheese head Nut and screw M6x40mm with double washer - Nos -20\nHexagonal head nut and bolt M3x20mm with double washer - Nos -20\nWooden screw 5mm- Nos -20\nReveted head screw with nut M6- Nos -20\nHexagonal head nut and bolt-M10x30mm with double washer Nos - 20		1	Set
100	100	Manufacturer's lable plate - 515 Army Base Wksp manufacturer plate, as per sample		2	Nos
101	101	Anchor Bolt - Size: 20 mm dia x 12"		6	Nos
102	102	U Bolt - U Bolt for Coupling Maruti Gyspy to intermedite frame with nut And washer as per requirment		6	Nos
103	103	Cable ties and tie bases (25mm packet of 100) as per sample - Standard cabel Ties, white nylon with a non-release ratchet lock action suitabel for binding cable or componets, Size-99x2.5 stock no.543-428 & Self Adhesive Fixing Clips (RB fixing clips, Type: RB8 (W-25mm), Stock No-170-5346		2	Pkt
104	104	Cable ties and tie bases (50mm packet of 100) as per sample - Standard cabel Ties, white nylon with a non-release ratchet lock action suitabel for binding cable or componets, Size-99x2.5 stock no.543-428 & Self Adhesive Fixing Clips (RB fixing clips, Type: RB8 (W-50mm), Stock No-170-5346		2	Pkt
105	105	Spiral Pipe 1.5" Dia ( Flexible Conduct) - Mtrls : Nylon PA6, thread: PG36, Temp: -40 deg to 120 deg,		5	Mtr
106	106	Spiral Pipe 1" Dia ( Flexible Conduct) - Mtrls : Nylon PA6, thread: PG36, Temp: -40 deg to 120 deg,		3	Mtr
107	107	Instrument panel (Meter Panel Gypsy with Modified Air pressure, fuel guage, Oil pressure guage, Speedometer, Amp meter, temperature guage for Gypsy with complete wiring) - Modified instrument pannel as look as Original, consisting of Set of panel indicators and Set of panel switches including , 1) Windscreen Wash Switch\n2) Modified Gypsy 4x4 gear Swich with shifting lever and lever knob 3) Tow Light Switch \n4) Dash Board Lamp 5) Fuel Guage (E-1/2-F)\n6) Oil Pressure Guage (0-10bar), 7) Warning Indicators\n8) Temperature Guage (40-120degree C),9) Speedo Meter (0-140km/hr)\n10) Air Pressure-1 (0-10bar) 11) Ammeter (-30 to 30+Amp)\n12) Air Pressure - 2 (0-10bar) 13) Black Out Switch\n14) Hazard Warning Switch 15) Fuel Gauge Change Over Switch\n16) Fog Lamp Switch 17) Push Start Switch, 18) Ignition Switch \n19 Flasher Unit\n		1	Nos
108	108	3 DoF Motion Platform - Make : TAH 3DoF Hydraulic (i) Payload : 700kg; 3 Degree of Freedom (Pitch +/-15 deg, Roll +/- 15 deg, Heave +/- 100mm); Velocity +/- 15deg/sec +/- 150mm/sec; Acceleration +/- 200 deg / sec2, +/- 400mm deg / sec2; Response time upto 80msec; Closed Height 800mm to 900mm; Operating Height 1100mm to 1200mm; Max Height 1200mm / SDD approved		1	Set
109	109	Hydraulic oil - Hydraulic Fluid SHo46		110	Ltr