| 1 | 1 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (Including all taxes but excluding GST) | 1 | 21321 | Sqm |
|---|
| 2 | 2 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Cla zuse 301.5 (Filling/Patri Filling) (For Without Cartage) (Including all taxes but excluding GST) | 2 | 9594.86 | Cum |
|---|
| 3 | 3 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (Filling/Patri Filling) (For WithCartage) (Including all taxes but excluding GST) | 3 | 533.03 | Cum |
|---|
| 4 | 4 | Brick Lining on both side of the road of M-150 bricks 7cm wide 11 cu. Deep laid with mud moratr including labour & supply of bricks finished to the required template and in proper allignment and also including dressing and ramming the excavated earth as directed by the Engineer-in-charge (Including all taxes but excluding GST) | 4 | 4.74 | Km. |
|---|
| 5 | 5 | Laying Brick Soling layer on prepared sub grade S.O.B. brick on end edging according to lines graded and cross section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soiling watering and rolling the same three wheeled road roller 80-100 Kn as per Technical Specification Clause 412. (Including all taxes but excluding GST) | 5 | 2160 | Sqm |
|---|
| 6 | 6 | Scapring old painted surface including disposal of all scraped material to a distance of 30 meter (100 ft.) as directed by engineer. (Including all taxes but excluding GST) | 6 | 9949.8 | Sqm |
|---|
| 7 | 7 | Construction of Embankment with Material Obtained from Roadway Cutting\nConstruction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 (Including all taxes but excluding GST) | 7 | 808.42 | cum. |
|---|
| 8 | 8 | Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 m\nExcavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3 (Including all taxes but excluding GST) | 8 | 1188.48 | cum. |
|---|
| 9 | 9 | Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C grade M 10 Nominal mix 1:3:6 (Including all taxes but excluding GST) | 9 | 241.5 | cum. |
|---|
| 10 | 10 | Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 Random Rubble masonary 1:4. (Including all taxes but excluding GST) | 10 | 504 | cum. |
|---|
| 11 | 11 | Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 P.C.C grade M 20 Nominal mix 1:2:4 (Including all taxes but excluding GST) | 11 | 59.14 | cum. |
|---|
| 12 | 12 | Granular Sub-base with Close Graded Material (Table:- 400-1) Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 ) for grading- I Material. (Including all taxes but excluding GST) | 12 | 1805.63 | Cum |
|---|
| 13 | 13 | WBM Grading 2\nProviding, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405.(Including all taxes but excluding GST) | 13 | 1781.1 | Cum |
|---|
| 14 | 14 | WBM Grading 3\nProviding, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.(Including all taxes but excluding GST) | 14 | 1393.36 | Cum |
|---|
| 15 | 15 | Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502.(Including all taxes but excluding GST) | 15 | 18578.2 | Sqm |
|---|
| 16 | 16 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503 (Including all taxes but excluding GST) | 16 | 18578.2 | Sqm |
|---|
| 17 | 17 | 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 Bitumen (VG-30) (Including all taxes but excluding GST) | 17 | 18578.2 | Sqm |
|---|
| 18 | 18 | Seal Coat\nProviding and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510 By Mechanical Means (Including all taxes but excluding GST) | 18 | 18578.2 | Sqm |
|---|
| 19 | 19 | Construction of un reinforced, dowel jointed at expansion and constrction joint only, plian cement concrete pavement, thickness as per design, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 (1:11/2:3)coarse and fine aggregates confirming to IS 383 maximun size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weight batcher using approved mix design, laid in approved ficed side form work (Steel channel, laying and fixing of 125 micron thick polythene film. wedges, steel pltaes including levelling the formwork as per drawing). spreading the concrete with shovels rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, constrcution joints as per norms, applying debonding strips primer, sealant, dowel bars, near approaches to bridge/culvert and construction, joints, admixtures as approved, curing of concrete slab for 14 day curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501 including cost of polythene sheet and dowel bar and also including complete shifting of material & concrete etc. (M-20)Same as above but when thickness is less than 20cm without dowel bar New Item 9(1) (Including all taxes but excluding GST) a | 19 | 978.75 | Cum |
|---|
| 20 | 20 | Supply of 80mm thick precast cement concrete I shape interlocking paver block ISI mark confirming to IS : 15658-2006 with top layer of minimum 5 mm thickness having plan dimension 200 x (160+120 mm) of O.P. Cement, Smooth high gloss finish, skid resistant, manufactured from rubber moulds through vibro-compression mechanism. The compressive strength of concrete paver block shall not be less than 50 MPa and weight 4.5 kg per including cost of material labour, T&P etc required for proper completion of the work as directed by Engineer-in-charge. (Including all taxes but excluding GST) | 20 | 2175 | Sqm |
|---|
| 21 | 21 | Excavation in foundation in ordinary soil (Loam, Clay or sand including lift upto 1.50 M. and lead upto 30 M and including filling watering and ramming of excavated earth into the trenches and the sides of foundation trebches or into the plinth and removal and disposal of surplus earth as directed by the engineer in charge upto a distance of 30 m foundation trenched (Including all taxes but excluding GST) | 21 | 1312.1 | Cum |
|---|
| 22 | 22 | Plaster in 1:4 Cement Mortar (Including all taxes but excluding GST) | 22 | 1242.53 | Sqm |
|---|
| 23 | 23 | Construction of Hume Pipe Culvert complete in all respect as per drawing (Including all taxes but excluding GST)\nReinforced Cement Concrete Pipe NP3 (1000 mm dia) | 23 | 7.5 | Rmt |
|---|
| 24 | 24 | Reinforced Cement Concrete Pipe NP3 (600 mm dia) | 24 | 30 | Rmt |
|---|
| 25 | 25 | Reinforced Cement Concrete Pipe NP3 (450 mm dia) | 25 | 52.5 | Rmt |
|---|
| 26 | 26 | Pointing with cement mortar (1:3) on brickwork as per drawing and technical specification Clauses 613.3 and 1204 (Including all taxes but excluding GST) | 26 | 63.43 | Sqm |
|---|
| 27 | 27 | Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m)RCC M 25 \nFor Slab Culvert (Including all taxes but excluding GST) | 27 | 4.28 | Cum |
|---|
| 28 | 28 | M.S. (tor Steel or plain) in plain work such as R.C.C. or R.B. work includinf bending for proper shape and including supply of steel & its wastage, bend, hooks, and authorised overlapping shall be measured and including cost of binding wire. \nFor Pucca Type Drain (Including all taxes but excluding GST) | 28 | 9.33 | Qtl |
|---|
| 29 | 29 | Brick masonry work in cement mortar 1:3 in parapet excluding pointing and plastering as per drawing and technical specifications Clauses 600, 900 and 1208. (Including all taxes but excluding GST) | 29 | 586.72 | Cum |
|---|
| 30 | 30 | Plastering with cement mortar (1:3), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204 (Including all taxes but excluding GST) | 30 | 197.27 | Sqm |
|---|
| 31 | 31 | White washing of parapet walls of CD work and tree truncks (Including all taxes but excluding GST) | 31 | 88.2 | Sqm |
|---|
| 32 | 32 | Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703\n5th Kilometre Stone (precast) (Including all taxes but excluding GST) | 32 | 1 | Nos. |
|---|
| 33 | 33 | Ordinary Kilometer Stone (Precast) (Including all taxes but excluding GST) | 33 | 5 | Nos. |
|---|
| 34 | 34 | 200 m stone (precast) (Including all taxes but excluding GST) | 34 | 24 | Nos. |
|---|
| 35 | 35 | Providing and fixing of Reflective Logo sign board at starting point & Intermediate distance with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including all taxes but excluding GST) | 35 | 4 | Nos. |
|---|
| 36 | 36 | Providing and fixing of reflective typical PMGSY Reflective logo and informatory sign board with a corrosion resitant 3mm and 4mm thick aluminum composite panel face to be fully covered with DM 5600 engineering grade prismatic / equvivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including all taxes but excluding GST) | 36 | 2 | Nos. |
|---|
| 37 | 37 | Providing and fixing of reflective Citizen information sign board with a corrosion resitant 4mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle. (Including all taxes but excluding GST) | 37 | 2 | Nos. |
|---|
| 38 | 38 | Providing and fixing of reflective Maintenance information sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle. (Including all taxes but excluding GST) | 37 | 1 | Nos. |
|---|
| 39 | 39 | Construction of CC Guard Post of Size 200X200X1000 mm complete in all repsect as per drawing. (Including all taxes but excluding GST) | 37 | 20 | Nos. |
|---|
| 40 | 40 | Providing and fixing Retro-Reflective cautionary mandatory and informatory signs as per IRC 67 with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle.\n600 mm equilateral triangle (Including all taxes but excluding GST) | 37 | 35 | No. |
|---|
| 41 | 41 | 600 mm Circular | 37 | 22 | No. |
|---|
| 42 | 42 | 800 X 600 mm Rectangular | 37 | 20 | No. |
|---|
