Supply Of Electrical Material At Ukaidam Under Electrical Sub Dn Ukai (2020-21).- 1 1 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA powder coated and high U.V. & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V,Power Factor more than 0.9, THD < 10 %, CCT 4000 K to 6500K, Uniformity ratio >0.7, Luminaireefficacy> 100 lumens/watt , LED driver efficiency > 85 % PHILIPS Lumileds /make LED used for luminaire. ( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (A) Tube Light with integral/ non-integral driver (d) 20-22 Watts, Surge - 2KV,IP-20, 4 feet Cat-lll Each 2 1 (F) Under Water Light,12V DC including Driver,IP-67 with die-cast/deep drawn housing with impact resistance clear toughened glass. (b) 12 watts Cat-llI Each Name of work :- Supply of Electrical material at Ukaidam under Electrical Sub Dn Ukai (2020- 21) Division :Ex. Engr Ukai Div no 1, Ukai Sub Division : Electrical Sub division Ukai 3 1 Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 1Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300 V,Power Factor more than 0.95, THD < 10 %, CCT 5000 K to 5700K, Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %. PHILIPS Lumileds / BridgeLux (U.S.A.) make LED used for luminaire. ( fittings required LM-79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge -4KV (d) above 36 to 48 watts Cat-lll Each 4 1 (e) above 48 to 60 Watts Cat-lll Each 5 1 (f) Above 60 watts to 90 watts Cat-lll Each 6 1 (B) Flood Light (IP-65), Surge -4KV (d) above 90 to 120 watts Cat-lll Each 7 1 (e) above 120 to 240 watts Cat-lll Each 8 1 Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with medium class Rigid PVC pipe and accessories (a) 2 wire 1.5 sq. mm Mtr 9 1 (b) 2 wire 2.5 sq. mm Mtr 10 1 (d) 3 wire 2.5 sq. mm Mtr 11 1 Providing & Erecting following Shockproof tissino type accessories erected on 3 mm thick PC (Polycarbonate) sheet in PVC/ Metal/Wooden Box. erected on wall/ ceiling. (1) One no Single pole 6 A Switch / Bell push Ea. 12 1 (2) One no 3/5 pin 6 A Socket Ea. 13 1 (3) One no Single pole 16 A Switch Ea. 14 1 (4) One no 6/16 A Universal Socket Ea. 15 1 (5) One no Single pole 16 A Switch & One no 6/16 A Universal Socket combined Ea. 16 1 (6) One no Single pole 16 A Switch & One no 6A/16 A Universal Socket combined with indicator & fuse Ea. 17 1 (7) Bakelite ceiling, rose Ea. 18 1 (8) Bakelite lamp holder Ea. 19 1 (9) Telephone Pin, Socket with suitable top Ea. 20 1 (10) Jack type tissino Telephone outlet Ea. 21 1 (11) Tissino type Neon ‘Indicator Lamp’ Ea. 22 1 (12) Tissino type TV antenna socket Ea. 23 1 (13) Tissino type 10A/16A Kitkat fuse Ea. 24 1 (14) Electronic Hum free EME Socket Type Steps Fan Regulator Ea. 25 1 Supplying electrical insulation L.T. Tape role with ISI marked having nominal width 1.8 cms nominal length 9.0 mtr nominal thickness 0.125 mm and having self adhesive PVC Ea. 26 1 Approved make CFL Retrofit 5 / 7 / 9 /11 Watt, erected if required Make PHILIPS Cat.III Ea. 27 1 Approved make C.F.L. Retrofit 13/15/18 Watt erected if required Make PHILIPS Cat.III Ea. 28 1 Approved make C.F.L.Retrofit 20 / 23 / 25 / 26 Watt. erected if required Make PHILIPS Cat.I Ea. 29 1 Cat.II Ea. 30 1 Cat.III Ea. 31 1 Approved make C.F.L.Retrofit of following size erected if required Make PHILIPS [A] 35/36 Watt Cat.III Ea. 32 1 [B] 40/45 Watt Cat.III Ea. 33 1 [C] 55/65/85 Watt Cat.III Ea. 34 1 Approved make CFL. Non-Retrofit 9/11 Watt erected if required Make PHILIPS Cat.II Ea. 35 1 Approved make CFL. Non-Retrofit 13 /15 / 18 Watt erected if required Cat.III Ea. 36 1 Approved make C.F.L.Non-Retrofit 35 / 36 Watt erected if required Cat.III Ea. 37 1 Approved make Spiral Retrofit CFL. for BC / Screw Type Holder of following size erected if required Make PHILIPS [a] 15/20/23/27 Watt Cat.III Ea. 38 1 [b] 35 / 36 Watt Cat.III Ea. 39 1 [c] 65/50 Watt. Cat.III Ea. 40 1 Approved make CFL. Ballast Having P.F. above 0.95 (Adopter) 9/11/13/15/18 Watt erected if required Cat.III Ea. 41 1 Approved make CFL. Ballast Having P.F. above 0.95 for 20 watt up to 86 watt erected if required Cat.III Ea. 42 1 Approved make Elliptical type Metal Halide lamps erected if required Make PHILIPS (i)70 Watt Cat.III Ea. 43 1 (ii)150 Watt Cat.III Ea. 44 1 (iii) 250 Watt. Cat.III Ea. 45 1 (iv) 400 Watt. Cat.III Ea. 46 1 Approved make Double Ended type Metal Halide lamps erected if required Make PHILIPS (i)70 Watt Cat.III Ea. 47 1 (ii)150 Watt Cat.III Ea. 48 1 (iii) 250 Watt. Cat.III Ea. 49 1 Approved make Tubular type Metal Halide lamps erected if required Make PHILIPS (i)70 Watt Cat.III Ea. 50 1 (ii)150 Watt Cat.III Ea. 51 1 (iii) 250 Watt. Cat.III Ea. 52 1 (iv) 400 Watt Cat.III Ea. 53 1 Supply of approved make lumilux triphospher T-5 tube suitable to operate on 120V - 300 V of (A) 14 Watt Cat III Ea. 54 1 (B) 24Watt / 28 watt Cat III Ea. 55 1 CFL ballast suitable for 9/11/13 watt tube Cat-llI Ea. 56 1 C F L Ballast 15/16/18/26 W Cat-llI Ea. 57 1 Supplying and erecting approved make, heavy duty polyester filled ballast suitable for 8OWatt. HPMV lamp Cat-llI Ea. 58 1 Supplying and erecting approved make, heavy duty polyester filled ballast suitable for 125 Watt. HPMV lamp. Cat-llI Ea. 59 1 Supplying and erecting approved make, heavy duty polyester filled ballast suitable for 250 Watt. HPMV lamp. Cat-llI Ea. 60 1 Supplying and erecting approved make, heavy duty polyester filled ballast suitable for 400 Watt. HPMV lamp. Cat-llI Ea. 61 1 Supplying and erecting approved make, heavy duty polyester filled ballast suitable for HPSV/ Metal Halide lamp. (a) 70 Watt. Cat-llI Ea 62 1 (b)150 Watt. Cat-llI Ea 63 1 (c)250 Watt Cat-llI Ea 64 1 (d)400 Watt Cat-llI Ea 65 1 Supplying and erecting approved make ignitor suitable for HPSV/ Metal Halide fittings, 7OW / 15OW / 25OW / 400W Ea. 66 1 Supplying & erecting control gear box, weather proof made of Cast aluminium with heavy duty copper polyester choke, condenser, MCB, connector block & earthing terminal complete erected with necessary screws, nuts & bolts clamps suitable for (A) For HPSV/MH Lamp with ignitor For One No. Lamp. Make PHILIPS (i) 7OW Cat-llI Ea 67 1 (ii)150 W Cat-llI Ea 68 1 (iii)250 W Cat-llI Ea 69 1 (iv)40OW Cat-llI Ea 70 1 Providing Approved make Triple Pole Cast Iron Clad Switch & rewirable Fuse with neutral link 415/500 V confirming to IS (a)16 A. Cat.III Ea. 71 1 (b) 32 A Cat.III Ea. 72 1 Erection & connection Charges For 16A/32A TP as following (a) on existing wooden block / A.I.frame Ea. 73 1 (b) on polished wooden block. Ea. 74 1 (c) on angle iron frame duly painted with Red Oxide Ea. 75 1 Providing Approved make Triple Pole Metal / Iron Clad Switch & Fuse with neutral link 415/500 V confirming to IS (a)63A Cat.III Ea. 76 1 (b) 100 A Cat.III Ea. 77 1 Providing Approved make Triple Pole Metal Clad Switch Fuse Unit 415/500 V. with HRC fuse of suitable load and neutral link confirming to IS. (a) 32 A Cat.III Ea. 78 1 (b) 63 A. Cat.III Ea. 79 1 (c) 100 A/125 A Cat.III Ea. 80 1 Providing Approved make Triple Pole Metal Clad Switch Fuse Unit 415/500 V. with HRC fuse of suitable load and neutral link confirming to IS (a)200 A Cat.III Ea. 81 1 (b) 250A Cat.III Ea. 82 1 (c) 300 A/315 A/325 A Cat.III Ea. 83 1 Providing Approved make Triple Pole metal clad switch fuse unit 415 / 500V. 400 A with HRC fuse of suitable load and neutral link confirming to IS Cat.III Ea. 84 1 Erection & connection charges for 32A/ 63 A / 100 A HRC TPN as following (a)on existing wooden block / A.I.frame Ea. 85 1 (b)Erection on New angle iron frame duly painted with red oxide Ea. 86 1 Erection & connection Charges for 200A/ 250A/ 300 A /325 A/400 A HRC TPN as following (a)on existing wooden block / A.I. frame Ea. 87 1 (b)Erection on New angle iron frame duly painted with red oxide . Ea. 88 1 Approved make Three Phase & Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. , 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities. .(a) 32 Amp Cat.III Ea. 89 1 (b) 63 Amp Cat.III Ea. 90 1 (c) 100Amp/125 Amp Cat.III Ea. 91 1 (d) 200 Amp Cat.III Ea. 92 1 (e) 250 Amp Cat.III Ea. 93 1 (f) 300/320 Amp Cat.III Ea. 94 1 (g) 400 Amp Cat.III Ea. 95 1 (h) 630 Amp Cat.III Ea. 96 1 (i) 800 Amp Cat.III Ea. 97 1 Approved make Four Pole LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities (a) 32 Amp Cat.III Ea. 98 1 (b) 63 Amp Cat.III Ea. 99 1 (c) 125 Amp Cat.III Ea. 100 1 (d) 200 Amp Cat.III Ea. 101 1 (e) 250 Amp Cat.III Ea. 102 1 (f) 315/320 Amp Cat.III Ea. 103 1 (g) 400 Amp Cat.III Ea. 104 1 (h) 630 Amp Cat.III Ea. 105 1 (i) 800 Amp Cat.III Ea. 106 1 Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating up to 125A. with Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III Ea. 107 1 Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal current rating up to 200A.with variable Thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections & complete erected in existing 16 G.M.S.housing ICS=100% of ICU only Cat III Ea. 108 1 Approved make Iron Clad or metal clad four pole change over switch 415V. confirming to IS of following capacity (A) 63 A Cat III Ea. 109 1 (B) 100 A / 125 A Cat III Ea. 110 1 Erection & connection charges for 63 A / 100A / 125 A change over switch as following (a)on existing wooden block / A.I.frame Ea. 111 1 (b)Erection on New angle iron frame duly painted with red oxide Ea. 112 1 Approved make Iron Clad or metal clad four pole change over switch 415V. confirming to IS of following capacity (A) 200 A / 250 A Cat-lll Ea. 113 1 (B) 400 A Cat-lll Ea. 114 1 (C) 630 A Cat-lll Ea. 115 1 (D) 800 A Cat-lll Ea. 116 1 Supplying & erecting approved make Four Pole 415V change over switch interior for panel mounting with operating mechanism A.C.23 duty confirming to IS for (A)32-40A Cat-lll Ea. 117 1 (B)63 A Cat-lll Ea. 118 1 (C)100-125A Cat-lll Ea. 119 1 (D)200A Cat-lll Ea. 120 1 (E)250A / 320A Cat-lll Ea. 121 1 (F)400A Cat-lll Ea. 122 1 Supplying KITKAT pattern porcelain cut-out with base of following current capacity erected on existing block board. (i) 16 A. 250 V . Ea. 123 1 (ii) 16 A. 500 V. Ea. 124 1 (iii) 32 A. 250/500 V. Ea. 125 1 (iv) 63 A 500 V Ea. 126 1 (v) 100 A. 500 V. Ea. 127 1 (vi) 200 A. 500 V. Ea. 128 1 Supplying Bolted Connections (BS type) HRC fuse link capable to withstand 80KA confirms to I.S. 13703 for following current capacity (A) up to 32 Amp. Ea. 129 1 (B) 36 Amp. to 63 Amp. Ea. 130 1 (C) 80 Amp. to 125 Amp. Ea. 131 1 (D) 126 Amp. to 200 Amp. Ea. 132 1 (E) 250 Amp. to 315 Amp. Ea. 133 1 (F) 400 Amp. to 450 Amp. Ea. 134 1 (G) 500 Amp. to 630 Amp. Ea. 135 1 Miniature circuit breaker single pole 1A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III Ea. 136 1 Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (a) For Electrical Installation up to 440V in normal soil Length of pipe - 1 Mtr Back filling compound - 1 Nos Bag of 15 Kg. Ea. 137 1 (b)For Electrical installation up to 11 KV in normal soil. Length of Pipe : 2.00 mtrs Back filling Compound :1 no. Bag of 25 Kg. Ea. 138 1 (c) For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. Length of Pipe : 3.00 mtrs Back filling Compound :2 nos Bags of 25 Kg. Ea. 139 1 Supplying & erecting XLPE(IS:7098) (I)-88 ISI unarmoured Aluminium cable 1.1 KV.grade to be erected as directed of following size. (a) 2 core 2.5 Sq. mm Mtr. 140 1 (b) 2 core 4 Sq. mm Mtr. 141 1 ( c ) 2 core 6 Sq. mm Mtr. 142 1 (d) 2 core 10 Sq. mm Mtr. 143 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables. (A) 3 core 2.5 Sq. mm Mtr. 144 1 (B) 3 core 4 Sq. mm Mtr. 145 1 (C) 3 core 6 Sq. mm Mtr. 146 1 (D) 3 core 10 Sq. mm Mtr. 147 1 (E) 3 core 16 Sq. mm Mtr. 148 1 (F) 3 core 25 Sq. mm Mtr. 149 1 (G) 3 core 35 Sq. mm Mtr. 150 1 (H) 3 core 50 Sq. mm Mtr. 151 1 (I) 3 core 70 Sq. mm Mtr. 152 1 (j) 3 core 95 Sq. mm Mtr. 153 1 (k) 3 core 120 Sq. mm Mtr. 154 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 155 1 (A-1) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 156 1 (B) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) Mtr. 157 1 (C) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) Mtr. 158 1 (D) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) Mtr. 159 1 (E) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Mtr. 160 1 (F) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core) Mtr. 161 1 (G) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core) Mtr. 162 1 (H) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core) Mtr. 163 1 (I) 3 1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core) Mtr. 164 1 (J) 3 1/2 core 400 Sq.mm ( 185 Sq. mm 1/2 core) Mtr. 165 1 (K) 3 1/2 core 500 Sq.mm ( 240 Sq. mm 1/2 core) Mtr. 166 1 (L) 3 1/2 core 630 sq. mm (300 sq.mm 1/2 core) Mtr. 167 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable. (a) 3 core 2.5Sq. Mm Mtr. 168 1 (a-1) 3 core 4 Sq. mm Mtr. 169 1 (b) 3 core 6 Sq. mm Mtr. 170 1 (c) 3 core 10 Sq. mm Mtr. 171 1 (d) 3 core 16 Sq. mm Mtr. 172 1 (E) 3 core 25 Sq. mm Mtr. 173 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 3 1/2 core 25 Sq. mm ( 10 Sq. mm 1/2 core) Mtr. 174 1 (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) Mtr. 175 1 (C) 3 1/2 core 50 Sq. mm ( 25 Sq. mm 1/2 core) Mtr. 176 1 (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) Mtr. 177 1 (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) Mtr. 178 1 (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Mtr. 179 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (A) 4 core 2.5 Sq. mm Mtr. 180 1 (A-1) 4 core 4 Sq. mm Mtr. 181 1 (B) 4 core 6 Sq. mm Mtr. 182 1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables. (C) 4 core 10 Sq. mm Mtr. 183 1 (D) 4 core 16 Sq. mm Mtr. 184 1 (E) 4 core 25 Sq. mm Mtr. 185 1 Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the run and backfilling the same and making the surface as normal ground. Mtr. 186 1 Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground. Mtr. 187 1 (B) If additional machineries like hammer driller or JCB use [Add] Mtr. 188 1 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables.(a) 2 to 4 core 2.5 / 4 Sq. mm Ea. 189 1 (b) 2 to 4 core 6 Sq. mm Ea. 190 1 (c) 2 to 4 core 10 Sq. mm Ea. 191 1 (d) 2 to 4 core 16 Sq. mm Ea. 192 1 (e) 2 to 4 core 25 Sq. mm Ea. 193 1 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (a) 3 core 35/50 Sq. mm Ea. 194 1 (b) 3 core 70 Sq. mm Ea. 195 1 (c) 3 core 95 Sq. mm Ea. 196 1 (d) 3 core 120 Sq. mm Ea. 197 1 (e) 3 core 150 Sq. mm Ea. 198 1 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (A) 3 & 1/2 / 4 core 25 Sq. mm Ea. 199 1 (B) 3 & 1/2 core 35/50 Sq. mm Ea. 200 1 (C) 3 & 1/2 core 70 Sq. mm Ea. 201 1 (D) 3 & 1/2 core 95 Sq. mm Ea. 202 1 (E) 3 & 1/2 core 120 Sq. mm Ea. 203 1 (F) 3 & 1/2 core 150 Sq. mm Ea. 204 1 (G) 3 & 1/2 core 185 Sq. mm Ea. 205 1 (H) 3 & 1/2 core 240 Sq. mm Ea. 206 1 (I) 3 & 1/2 core 300 Sq. mm Ea. 207 1 (J) 3 & 1/2 core 400 Sq. mm Ea. 208 1 (K) 3 & 1/2 core 500 Sq. mm Ea. 209 1 Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm Ea. 210 1 (B) 10 Sq.mm Ea. 211 1 (C) 16/25 Sq.mm. Ea. 212 1 (D) 35/50 Sq.mm. Ea. 213 1 (E) 70 Sq.mm. Ea. 214 1 (F) 95 Sq.mm. Ea. 215 1 (G) 120 Sq.mm. Ea. 216 1 (H) 150 Sq.mm. Ea. 217 1 ( I ) 185 Sq.mm. Ea. 218 1 (J) 225 Sq.mm. Ea. 219 1 (K) 300 Sq.mm. Ea. 220 1 (L) 400 Sq.mm. Ea. 221 1 (M) 500 Sq.mm. Ea. 222 1 Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz. 1200 mm sweep complete having 4 blades Aluminium body and blade sets having ornamental design shanks, canopy erected with earthing [ Make shall be approved by Engineer in Charge] Ea. 223 1 Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM [A] 305 mm dia 900 RPM Cat.II Ea. 224 1 [B] 380 mm dia 900 RPM Cat.II Ea. 225 1 [C] 380 mm dia 1400 RPM Cat.II Ea. 226 1 [D] 450 mm dia 900 RPM Cat.II Ea. 227 1 [E] 450 mm dia 1400 RPM Cat.II Ea. 228 1 Providing & erecting approved make street light / wall mounting junction box compression moulded from DMC (thermoset plastic) vertical sliding cover having locking with square head stud loop in / loop out in built terminal suitable for four core cable, waterproof of I.P. 54 protected with clamp or bolt nut & earth bolt of following size. [A] 200mm x 127mm x 83 mm Ea 229 1 [B] 250mm x 194mm x 99 mm Ea 230 1 [C] 327mm x 254mm x 120 mm Ea 231 1 Providing street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top having sufficient fastners for fixing the brackets and having spread of 1 mtr. length with suitable rise as per site condition & suitable welded stiffener reducer and nipple with check nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 1 Mtr Ea 232 1 [B] Double Arm Bracket 1 Mtr Ea 233 1 [C] Three Arm Bracket 1 Mtr Ea 234 1 [D] Four Arm Bracket 1 Mtr Ea 235 1 Supplying and erecting Street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5mm/80mm/require size of pole top having nuts and bolts for fixing the brackets and having spread of 0.5 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener reducer and nipple with checknut complete painted with one coat.of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single Arm bracket 0.5 Mtr Ea 236 1 [B] Double Arm Bracket 0.5 Mtr Ea 237 1 [C] Three Arm Bracket 0.5 Mtr Ea 238 1 [D] Four Arm Bracket 0.5 Mtr Ea 239 1 Painting of street light pole with bracket complete with two coats of Aluminium paint for following size of pole. [a] up to 4 mtr Ea 240 1 [b] up to 6 mtr. Ea 241 1 [c] up to 9 mtr Ea 242 1 [d] up to 10 to 13 mtr Ea 243 1 Supplying & erecting approved make time switch with single pole airbreak contacts suitable for 230 V.15/16A.complete with self starting motor driven clock ‘ON’ &’ OFF’ automatic arrangement at any predetermined time during each 24 hours,With nickel cadmium rechargeable battery backup erected as directed. Ea. 244 1 Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection erected as directed. Ea. 245 1 Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only) (a) DOL up to 5.0 H.P. Ea. 246 1 (b) DOL for 7.5 H.P. Ea. 247 1 Supplying & erecting approved make 3 phase motor control cubical panel ( Star - Delta) made from16 G. CRCA sheet duly painted with epoxy powder painted inside and outside with hinged doors and locking arrangement, consisting of suitable size of ON- OFF isolator (AC - 3/23 duty) main fuses, single phasing preventer cum water level. Guard (Complete unit), Toggle switch to by pass Single phase preventer cum WLG, indicating lamps for R- Y- B phases, over load relay, Automatic water level controller, Ammeter & Voltmeter each with two way selector switch incoming wires duly socket Crimped, Panel to be erected on angle iron frame grouted on wall as directed. Star Delta & main contactor, overload relay, thermal / Electronic Star delta cutoff timer, start - stop push buttons. The isolator overload relay & contactors of L& T, Siemens or Cuttler Hamer make only. Panel to be erected on angle iron frame ground on wall. (a) S/D up to 7.5 H.P. Ea. 248 1 (b) S/D up to 10 H.P. Ea. 249 1 (c) S/D up to 12.5 H.P. Ea. 250 1 (d) S/D up to 15 HP Ea. 251 1 (e) S/D up to 22.5 H.P. Ea. 252 1 (f) S/D up to 30 H.P. Ea. 253 1 Providing and erecting AC-3 duty 3 pole power contactor with 2 NO & 2 NC aux contacts complete with 415V/220V operating coil suitable for (L&T, BCH,T.C., Siemens, C&S make). (a) for 25 / 32 A rating Ea. 254 1 (b) for 40 A rating Ea. 255 1 (c) for 60 / 70 A rating Ea. 256 1 (d) For 80 / 95 A Rating Ea. 257 1 (e) for 110 A rating Ea. 258 1 Providing and erecting AC-3 duty 3 pole power contactor thermal over load relay ( L & T BCH / Siemens, / C & S / Alstom make) (a) For 4 - 15 Amp. Rating Ea. 259 1 (b) For 25 Amp rating, Ea. 260 1 (c) For 32 Amp. rating Ea. 261 1 (d) For 40 Amp. Ea. 262 1 [e] For 48 to 70 Amp. Ea. 263 1 (f) For 80 to 110 Amp. Ea. 264 1 Providing and erecting AC-3 duty 4 pole A.C. Coil with 2 NO & 2 NC aux contacts complete with 415V/220V operating coil suitable for (L&T, BCH,T.C., Siemens, C&S make). (a) for 25 / 32 A rating Ea. 265 1 (b) for 40 A rating Ea. 266 1 (c) for 60 / 70 A rating Ea. 267 1 (d) For 80 / 95 A Rating Ea. 268 1 (e) for 110 A rating Ea. 269 1 Rewinding of submersible motor by using approved make PVC insulated copper winding Cores of suitable size complete with connection. Capacity Suitable for pump of following size. Dismantled Materials to be retained by agency. (A) 5 HP Ea. 270 1 (B) 7.5 H.P Ea. 271 1 (C) 10 to 15 H.P Ea. 272 1 (D) 16 to 20 H.P Ea. 273 1 (E) 21 to 25 H.P Ea. 274 1 (F) 26 to to 35 H.P Ea. 275 1 (G) 36 to 45 H.P Ea. 276 1 (H) 46 to 54 H.P Ea. 277 1 Providing, and erecting 11 KV D.P. 6 mtr. high Structure made of 6 x 3 ‘I’- Section Girder, 4 x 2channels, clamps, nuts, bolts etc. Suitable for erection of the followings duly connected with necessary ACSR conductors. as per drawing approved by the Engineer- in charge complete with following. Height as per IS 7 Mtr above ground ) (A) 11 KV 200 Amps Drop out fuses with S.R.B.P. tubes carries.-Three nos (B) 11 KV G.O.D. switch complete with insulators, operating handle with galvanised pipe, Sq.bar etc. 400 Amp.- One Set (C) 11 KV lightening arrestor with clamp- Three Nos. (D) 11 KV shackle insulators- Six Nos. (E) The above D.P. structure should be earthed with 25 mm.X 3 mm thick double copper earth strips run separately and connected with separate copper plate earth electrode.
