Military Engineer Services-MES has published Provision Of Dsc Gourd Post At Lal Gate , Deficient Kitchen Sinks , Exhaust Fans , Ceiling Fans , Special Repair To Ber Cooling Appliances Water Supply , Electric Supply , And Iron Grill Doors And Windows At Jandwal Pathankot Provn Of Dsc Gourd Pos. Submission Date for this Tender is 03-02-2021. Kitchen Equipment Tenders in GE (AF) PATHANKOT Punjab. Bidders can get complete Tender details and download the document.
| Name of Work : PROVN OF DSC GOURD POST AT LAL GATE, DEFICIENT KITCHEN SINKS, EXHAUST FANS, CEILING FANS , SPECIAL REPAIR TO BER COOLING APPLIANCES WATER SUPPLY, ELECTRIC SUPPLY, AND IRON GRILL DOORS & WINDOWS AT JANDWAL PATHANKOT | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil for roads to required slope gradient, camber etc complete all as specified and directed by the Engineer-in-charge | 360 | Sqm | |
| 2 | 2 | Excavating over areas, n exc 1.5m deep and getting out in average soil complete all as specified and all as directed by Engineer-in-Charge. | 20 | Cum | |
| 3 | 3 | Excavation in trenches n. exc 1.5 m wide for foundations, pipe line, laying of cables etc. and not exceeding 1.5 m deep and getting out in soft/ loose soil complete all as specified & directed by Engineer-in-charge. | 150 | Cum | |
| 4 | 4 | PCC Type D-2, 1:4:8 (using 40 mm grade stone aggregate) as in foundation filing of mass conrete complete all as specified and all as directed by Engineer-in-Charge. | 13 | Cum | |
| 5 | 5 | Earth filling under floors spreading and levelling in layers n exc. 25 cm thick, ramming including watering as required in floors with earth obtained from excavation complete all as specified and all as directed by Engineer-in-Charge. | 6 | Cum | |
| 6 | 6 | Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm in soft/loose soil complete all as specified and directed by Engr-in-Charge | 70 | Cum | |
| 7 | 7 | Removal of surplus excavated soil to a distance n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above starting point complete all as specified and directed by Engr-in-Charge | 83 | Cum | |
| 8 | 8 | Hardcore broken stone of gauge n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and all as directed by Engineer-in-Charge. | 2 | Cum | |
| 9 | 9 | Use and waste of form work to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and all as directed by Engineer-in-Charge. | 31 | Sqm | |
| 10 | 10 | Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and all as directed by Engineer-in-Charge. | 2525 | Kg | |
| 11 | 11 | Mild steel TMT bars 6mm to 8 mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and all as directed by Engineer-in-Charge. | 1050 | Kg | |
| 12 | 12 | Providing RCC Mix M-25 (design mix) (using 20 mm graded stone aggregate ) as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and all as directed by Engineer-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) | 6.8 | Cum | |
| 13 | 13 | Use and waste form work to sides of columns, pillars etc. of fair finished surfaces of concrete complete all as specified and all as directed by Engineer-in-Charge. | 28 | Sqm | |
| 14 | 14 | Providing RCC Mix M-25 (design mix) (using 20 mm graded aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and all as directed by Engineer-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) | 4.5 | Cum | |
| 15 | 15 | Use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, chajja, shelves etc. including support of fair finished surfaces of concrete complete all as specified and all as directed by Engineer-in-Charge. | 65 | Sqm | |
| 16 | 16 | Providing RCC Mix M-25 (design mix) (using 20 mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and all as directed by Engineer-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) | 4.5 | Cum | |
| 17 | 17 | Use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n. exc. 200 mm thick, rough finished surface of concrete complete all as specified and all as directed by Engineer-in-Charge. | 35 | Sqm | |
| 18 | 18 | Providing RCC Mix M-25 (design mix) ( using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, lintel bands and in columns in floors or roofs, landings, balconies and in shelves and the like complete all as specified and all as directed by Engineer-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) | 5 | Cum | |
| 19 | 19 | Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better surfaces of concrete complete all as specified and all as directed by Engineer-in-Charge. | 56 | Sqm | |
| 20 | 20 | Providing RCC Mix M-25 (design mix) ( using 20mm graded crushed stone aggregate) as in walls, retaining walls, basement walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and all as directed by Engineer-in-Charge. (Note :- Reinforcement shall be measured and paid separately under respective item) | 5 | Cum | |
| 21 | 21 | Brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge | 38 | Cum | |
| 22 | 22 | Rendering 5 mm thick in CM 1:3 on concrete surface of ceiling, finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge. | 40 | Sqm | |
| 23 | 23 | Rendering 15mm thick on brick work or concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge. | 135 | Sqm | |
| 24 | 24 | Rendering 15mm thick on brick work or concrete surface in cement mortar (1:4) finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-Charge. | 170 | Sqm | |
| 25 | 25 | Preparation of new plastered surfaces and applying three coats of white wash on ceiling complete all as specified & directed by Engineer-in-Charge. | 40 | Sqm | |
| 26 | 26 | Preparation of new plastered surfaces to distempering and applying two coats of oil bond distemper white or tinted on newly plastered wall surfaces complete all as specified & directed by Engineer-in-Charge. | 135 | Sqm | |
| 27 | 27 | Preparation of new plastered surfaces and applying two coats of Acrylic exterior emulsion paint with camouflage pattern (four) or more shades over a coat of primer of olive green colour as directed by Engineer-in-Charge and as required at site including necessary scaffolding and other safety arrangement to work up to a height of 8 metre metres complete all as specified & directed by Engineer-in-Charge. | 170 | Sqm | |
| 28 | 28 | Rendering 15mm thick in CM 1:4 on roof surface with water proofing compuund as per manufactures instruction including fair finishing to top surface complete all as specified & directed by Engineer-in-Charge. | 20 | Sqm | |
| 29 | 29 | Supply only water proofing compound complete all as specified & directed by Engineer-in-Charge. | 0.5 | Ltr | |
| 30 | 30 | Preparation of concrete/Plastered surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying \nfollowing roof treatment complete all as directed by Engr-in-Charge :-\n(a) Applying 1st course of bitumen primer conforming to IS-3384 @ 0.4 Kg/Sqm cover prepared surface till the surface is properly impregnated and insolvent oil primer shall be allowed to evaporate completely.\n(b) Applying 2nd course of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 1800 C and applied @ 1.2 Kg per sqm. \n(c) Applying 3rd coarse of APP (Atactic polypropylene) modified polymeric membrane 4mm thick weight not less than 4.5 Kg/Per sqm with 160gm per sqm non woven polyester made at centre core reinforced laid with 75mm side overlap and 100mm overlap. The membrane has to be laid with LPG torch and overlap sealed and fineshed neat. All joint and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @ of 200ml/Bag of cement and curved before laying membrane. \n(d) Applying 4th course of a coat of bounding material with blown type bitumen of grade 85/25 heating to a working temperature 1800 C and applied @ 1.2Kg per Sqm.\nNote - Ponding shall be done over RCC slab by filling water which shall be kept there or 48 hours. In case a slightest indication of seepage/leakage is noticed, the same shall be rectifed by grounitng the affected portion at no extra cost. Thereafter ponding test shall be repeated till there is no indication of seepage/leakage before application of roof treatment. A proper record of ponding test of RCC slabs shall be maintained by Engr-in-Charge. The arrangement for ponding test shall be made by contractor. The arrangement for ponding to be included in the quoted rates. nothing extra shall be admissible on this account.\n | 20 | Sqm | |
| 31 | 31 | Pressed steel frame made out of MS sheet 1.25mm thick of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed by Engineer-in-Charge.\nNOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement. | 10 | RM | |
| 32 | 32 | 35mm thick 2nd class hard wood factory made plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, complete all as specified & directed by Engineer-in-Charge.\n | 4 | Sqm | |
| 33 | 33 | 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.\n | 2 | Sqm | |
| 34 | 34 | Factory made steel window/Ventilator 1.25mm thick box type (primer coated) EWR hollow P section of size 60mmx25mm including grell using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed skelton shutter ERW section 50mmx20mm and 1mm thick with two openable leaf consisting two nos shash bar of T section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mmx25mm and 1.25mm thick refer TD Drawing No. CEAF/AR-480/2015 Sheet No. 2(A)/4 dated 30.12.2015 including cutting holes and good dismantled portion in PCC (1:2:4) type B1 and match the disturbed portion with existing surface four Nos for each window including following fitting welded to frame shutter:\n(a) Hold fast 150mm long of 12mmx3mm made to shape 04 Nos per window.\n(b) Handle of Z section 20mmx3mm. 100mm long- per No leaf.\n(c) MS tower bolt 150mm long-02 Nos per leaf.\n(d) Z section 20mmx25mm, 100mm long stopper 01 No per leaf.\n(e) Cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 01 No per leaf.\n(f) MS pintal hinges of size 75mmx12mm. 02 Nos per leaf.\n(g) Including two coats of synthetic enamel paint complete and 3mm thick glass sheet .\nNOTE: During fixing of window, surface shall be make good in plumb with existing finishes like cement plaster,similar wall tiles,floor tiles etc as per site requirement. | 5 | Sqm | |
| 35 | 35 | Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour sheet reinforcement with MS square tube all as specified, in built fixed to wall with CSK screw 100 mm long, screw holding strength of PVC frame Shall be 200 Kgf ,fixing shall be done with anchor screw ( 150 mm x 8mm) with PVC Nylone SLEEVE fixed with screw complete all as specified and directed by Engineer-in-Charge. NOTE:- During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement. | 5 | RM | |
| 36 | 36 | Factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; partly glazed i.e. upper panel will be glass pane fitted externally in the clear space & lower panel will be plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at the site as per specification described in SSR 2004 Part II Item No 881 complete all as specified and directed by Engineer-in-Charge. | 5 | Sqm | |
| 37 | 37 | Supply and fixing aluminium anodised barrel tower bolt of extruded section 200mm long complete all as specified and directed by Engineer-in-Charge. | 5 | Each | |
| 38 | 38 | Supply and fixing aluminium handles anodised cast type 125mm long complete all as specified and directed by Engineer-in-Charge. | 8 | Each | |
| 39 | 39 | Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled complete all as specified and directed by Engineer-in-Charge. | 12 | Each | |
| 40 | 40 | Supply and fixing aluminium alloy, anodised, sliding door bolt(ISI Marked) 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge. | 2 | Each | |
| 41 | 41 | Supply and fixing 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete, fixed in repairs complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 42 | 42 | Supply and fixing floor door stopper of aluminium alloyof overall length of cover plate 140mmm and tongue, anodised, with hard drawn steel spring, fixed on door complete all as specified and directed by Engineer-in-Charge. | 2 | Each | |
| 43 | 43 | Supply and fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks, or galvanized wire staples complete all as specified and directed by Engineer-in-Charge. | 6 | Sqm | |
| 44 | 44 | Supply and fixing mild steel work conforming to Fe-410-0 or Fe-310 as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars,grills, walkways, railing, framed work of water tanks and similar works complete all as specified and directed by Engineer-in-Charge. | 120 | Kg | |
| 45 | 45 | Supply and fixing 18-20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing upto desired satisfaction complete all as specified and directed by Engineer-in-Charge. | 45 | Sqm | |
| 46 | 46 | Supply and fixing non skid ceramic tiles coloured size 300 x 300mm x 7 to 8mm thick in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement incl 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement complete all as specified and directed by Engineer-in-Charge. | 4 | Sqm | |
| 47 | 47 | Supply and fixing glazed ceramic coloured/printed tiles 300mm x 200mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge. | 20 | Sqm | |
| 48 | 48 | Supply and fixing vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 49 | 49 | Supply and fixing in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, fluhsing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 50 | 50 | Supply and fixing 600mmx450mm bevelled edge looking mirror of selected quality with 4.5mm thick polished glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with CP brass screws and cup washers fixed in repairs complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 51 | 51 | Supply and fixing vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but excluding waste pipe, waste fittings etc complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 52 | 52 | Supply and fix 15 mm bore bib taps, chromium plated cast copper alloy, high pressure screwed down, screwed for iron pipe or for brass ferrule complete all as specified and all as directed by Engineer-in-Charge. | 2 | Each | |
| 53 | 53 | Supply and fix 15 mm dia brass chromium plated pillar tap, with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe complete all as specified and all as directed by Engineer-in-Charge. | 1 | Each | |
| 54 | 54 | Supply and fix 450mm long PVC connection 15mm bore with PTMT nuts complete all as specified and all as directed by Engineer-in-Charge. | 2 | Each | |
| 55 | 55 | Supply only 32mm dia waste pipe of polythelene,flexible, for wash hand basin or kitchen sink complete all as specified and all as directed by Engineer-in-Charge. | 1 | Each | |
| 56 | 56 | Supply and fixing of 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and all as directed by Engineer-in-Charge. | 2 | Each | |
| 57 | 57 | Supply and fixing of PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls complete all as specified and all as directed by Engineer-in-Charge. | 12 | RM | |
| 58 | 58 | Supply and fixing of 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and all as directed by Engineer-in-Charge. | 15 | RM | |
| 59 | 59 | Supplying and fixing of medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete all as specified and all as directed by Engineer-in-Charge. | 35 | RM | |
| 60 | 60 | Supplying and fixing of medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete all as specified and all as directed by Engineer-in-Charge. | 25 | RM | |
| 61 | 61 | Supplying and fixing of rotational moulded polythene water storage tank (Cylindrical vertical withclosed top) hoisted and fixed in position of 500 ltrs capacity fixed with PVC tank nipples,PVC float valve 20mm, complete all as specified in SSR Part I complete all as specified and all as directed by Engineer-in-Charge. | 1 | Each | |
| 62 | 62 | Supplying and fixing of gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 15 mm dia complete all as specified and all as directed by Engineer-in-Charge. | 1 | Each | |
| 63 | 63 | Supplying and fixing of gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and all as directed by Engineer-in-Charge. | 2 | Each | |
| 64 | 64 | Providing 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, laid in alternate ways, surface finished even and fair without using extra cement complete all as specified and directed by Engr-in-Charge | 18 | Sqm | |
| 65 | 65 | Preparing steel and iron surfaces (new) of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed by Engr-in-Charge | 15 | Sqm | |
| 66 | 66 | Providing 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base , surface finished even and fair without using extra cement to received tiles incl necessary formwork complete all as specified and directed by Engr-in-Charge | 390 | Sqm | |
| 67 | 67 | Supplying and fixing of 80mm thick, machine pressed precast concrete interlocking paver block, with grey cement and no pigment, any shape and size confirming to IS 15658-2006, M-40 Grade and laid over 30mm thick stone dust cushioning complete all as specified and directed by Engr-in-Charge | 370 | Sqm | |
| 68 | 68 | Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills,steps,and other similar bands,plinth courses, string courses, lacing courses, parapets and railing upto 60cm height,copings,kneelers,apex stone,bed plates and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge | 3 | Cum | |
| 69 | 69 | Salt Glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed and testing complete all as specified and directed by Engr-in-Charge | 110 | RM | |
| 70 | 70 | Concrete bed to drain pipes in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia SWG pipe complete all as specified and directed by Engr-in-Charge | 110 | RM | |
| 71 | 71 | Precast RCC 1:2:4 type B1 as in landings, cover slab,chajjas etc.and similar articles with plain faces set in CM 1:6 complete all as specified and directed by Engr-in-Charge | 0.3 | Cum | |
| 72 | 72 | Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 150 mm bore drain pipe complete all as specified and directed by Engr-in-Charge | 1 | Each | |
| 73 | 73 | PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in surface channels,drains, complete all as specified and directed by Engr-in-Charge | 4 | Cum | |
| 74 | 74 | Demolition of existing plateform or shelf or built in washing point of any description for making provision of steel sink with drainage board and removing demolished material to a distance exc 50 m but n.exc. 100 mtr, complete all as specified and directed by Engr-in-Charge | 70 | Each | |
| 75 | 75 | Glazed ceramic coloured tiles size 450mm x 300mm x 7 to 8mm thick on vertical surfaces of wall such as skirting/dado etc set & jointed in cement slurry and pointed with white or coloured cement to match the colour tiles including 10mm thick rendering on brick/concrete surface in cement mortor 1:4 and refixing old sanitary fitting such as WHB, mirror, flushing cistern etc. (Contractor shall quote the rate including the same) complete all as specified and directed by Engr-in-Charge | 255 | Sqm | |
| 76 | 76 | Green Marble work 18-20mm thick (Table rubbed and polished) in cooking platforms and like set in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble incl 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge | 95 | Sqm | |
| 77 | 77 | Supplying and fixing of medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors /ceiling for 15 mm bore GI tubing and including taking down existing GI tubing complete all as specified and all as directed by Engineer-in-Charge. | 175 | RM | |
| 78 | 78 | Cutting chases, pinning in ,brick walls, and making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades and cutting chasis for concealed water tubing or concealed conduit wiring etc, making good cuttings not exc 10 cm girth complete all as specified and all as directed by Engineer-in-Charge. | 105 | RM | |
| 79 | 79 | Supply and fix 15 mm bore bib taps, chromium plated cast copper alloy with capstan head, fancy type handle, high pressure screwed down for iron pipe, fixed in repairs complete all as specified and all as directed by Engineer-in-Charge. | 140 | Each | |
| 80 | 80 | Supply and fix sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and all as directed by Engineer-in-Charge. | 70 | Each | |
| 81 | 81 | Supply and fix collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified, erected in position and securing runners with holdfasts and brackets complete all as specified and all as directed by Engineer-in-Charge. | 12.5 | Sqm | |
| 82 | 82 | Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 W (Gde E-250) Quality-A complete all as specified and all as directed by Engineer-in-Charge. | 560 | Kg | |
| 83 | 83 | Preparing new steel surfaces of any description exc 10cm width or grith and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engr-in-Charge | 18 | Sqm | |
| 84 | 84 | Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable multistrand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable(green colour) as earth lead in and including surface/concealed as required in non rigid PVC conduit medium grade with all fittings(ISI marked) controlled by one switch including CI / MS sunk box of required size including plastic lamitated sheet as required and other accessories as required including cutting chases to wall and making good the distributed surfaces to match with the existing specification complete all as specified and directed by Engr-in-Charge | 130 | Per Point | |
| 85 | 85 | All as per item No. 84 above here in before but for One 3/5 pin socket outlet 5 amps on independent board, with cables 1.5 sqmm FRLS PVC complete all as specified and directed by Engr-In-Charge. | 4 | Per Point | |
| 86 | 86 | All as per item No. 84 above here in before but for One 3/5 pin socket outlet 5 amps on same board with other switches, with cables 1.5 sqmm FRLS PVC complete all as specified and directed by Engr-In-Charge. | 2 | Per Point | |
| 87 | 87 | All as per item No. 84 above here in before but for One 5 pin socket outlet 15 amps on independent board, with cables 2.5 sqmm FRLS flexible unsheathed copper conductor wire complete all as specified and directed by Engr-In-Charge. | 2 | Per Point | |
| 88 | 88 | Supply and fixing in replacement switch piano single pole one way 5/6 amps, flush type 230 volts complete all as specified and directed by Engr-In-Charge. | 132 | Each | |
| 89 | 89 | Supply and fixing in replacement socket outlet 5 pin 5/6 Amps, 230 volts, flush type complete all as specified and directed by Engr-In-Charge. | 6 | Each | |
| 90 | 90 | Supply and fixing in replacement socket outlet multipurpose 15 Amps, 230 volts, flush type complete all as specified and directed by Engr-In-Charge. | 2 | Each | |
| 91 | 91 | Supply and fixing in replacement switch piano type, one way 15 Amps, 230 volts, flush type complete all as specified and directed by Engr-In-Charge. | 2 | Each | |
| 92 | 92 | Supply and fixing in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed by Engr-In-Charge. | 56 | Each | |
| 93 | 93 | Supply and fixing in replacement Ceiling rose, 3 point/ PVC/polycarbonate, 5 Amps, 230 volts, isolated body complete all as specified and directed by Engr-In-Charge. | 127 | Each | |
| 94 | 94 | Supply and fixing in replacement Bell Push flush type 5/6 Amps, single pole, one way 230 volts complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 95 | 95 | Supply and fixing in replacement Bell Ding dong type , single phase, 230 volts complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 96 | 96 | Supply and fixing in replacement Distribution board iron clad, double door SPN 8 way 230 Volts complete with appropriate size copper bus bar and neutral link complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 97 | 97 | Supply and fixing in replacement MCB SPN 6 to 32 Amps, 230 Volts, 10kA complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 98 | 98 | Supply and fixing in replacement MCB SP 6 to 32 Amps, 230 Volts, 10kA complete all as specified and directed by Engr-In-Charge. | 6 | Each | |
| 99 | 99 | Supply and fixing LED light fittings 7 Watt, 230 Volts,indoor type wall mounting type made up of polycarbonate with lamp holder, LED Lamp 7W, with B-22 base, connector block etc complete with all accessories, pre-wired complete all as specified and directed by Engr-In-Charge. | 4 | Each | |
| 100 | 100 | Supply and fixing exhaust fan 300mm sweep single phase 230 volts 50 Hz AC supply totally enclosed motor in metallic body complete with louvers including making provisions for fixing and mounting fan, cutting chases to wall etc including making good to disturbed surfaces matching with existing, connecting electrically using suitable size PVC insulated flexible copper conductor cable over all sheathed including making good to the disturbed surfaces matching with existing complete all as specified and directed by Engr-In-Charge. | 56 | Each | |
| 101 | 101 | Supply and fixing Ceiling fan 1200mm sweep single phase 230 volts 50 Hz AC supply totally enclosed copper wound motor complete with down rod, including hanging of fan using suitable clamp in hanging rod/GI Pipe 40mm bore, connecting electrically using suitable size PVC insulated flexible copper conductor cable over all unsheadhed complete all as specified and directed by Engr-In-Charge. | 56 | Each | |
| 102 | 102 | Supply and fixing Wall mounted air circulator fan 450mm sweep single phase 230 volts 50 Hz AC supply totally enclosed motor in metallic enclosure, including hanging provisions, connecting electrically using suitable size PVC insulated flexible copper conductor cable over all unsheadhed complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 103 | 103 | Supply and fixing weather proof Bulk Head LED light fittings not less than 7 Watt, 230 Volts,made up of polycarbonate connector block, LED driver etc complete with all accessories, pre-wired complete all as specified and directed by Engr-In-Charge. | 5 | Each | |
| 104 | 104 | Supply and fixing LED Tube light fitting 18 Watt, 230 Volts,box type with LED tube rod including LED Driver, connector block etc complete with all accessories, pre-wired complete all as specified and directed by Engr-In-Charge. | 3 | Each | |
| 105 | 105 | Supply and fixing Flood light fitting LED type 150 Watt with pressure die casted aluminium housing with flat glass optical cover with lens to ensure uniform distribution, IP 65 protection including LED Driver and housing as per BIS standards including connecting terminals, mounting clamp, mounting bracket if required and all other accessories reqd for fixing and making fitting operational complete all as specified and as directed by Engineer-in-Charge. | 2 | Each | |
| 106 | 106 | Earthing complete with galvanised steel earth plate electrode of size 600x600x6mm thick as earth electrode not less than 2.25mtr below ground level with top edge of earth plate not less than 1.50 metre below normal ground level connected to galvanised earth wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth strip protection pipe GI light grade 40mm dia from earth plate to main switch board/panel, watering pipe 20mm dia medium grade with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 with adequate quantity of charcoal dust and salt all around the earth plate including all necessary earth work in any type of soil, removing surplus excavated material all as required at site and specified in EP No 3 of SSR part I 2009 and directed by Engineer-in-charge. (Note:- Up to 7.5 Mtr length of GI protection pipe and copper strip shall be deemed to be included in unit rate quoted by tenderer. | 1 | Each | |
| 107 | 107 | Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed by Engr-In-Charge. | 5 | RM | |
| 108 | 108 | Sub Class 'B' bricks laid dry flat to cover the cable with width equal to the length of cable and abutting each other for protection of cable complete all as specified and as directed by Engr-In-Charge. | 2300 | Each | |
| 109 | 109 | Sand cushioning to underground cables providing a layer of 8cm thick before laying the cable and 15cm thick after laying,stretching and testing the cable complete all as specified and directed by Engr-In-Charge. | 23 | Cum | |
| 110 | 110 | Supply and laying MS Tubes of 40mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in trenches for cable protection complete all as specified and directed by Engr-In-Charge. | 12 | RM | |
| 111 | 111 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core confirming to IS:7098(Part-I) of 1988 complete all as specified and directed by Engr-In-Charge. | 150 | RM | |
| 112 | 112 | Boring of holes under road, pavement, hard standing by trenchless technology or by mechanical means including making good to existing disturbed surfaces matching with existing complete all as specified and directed by Engr-In-Charge. | 12 | RM | |
| 113 | 113 | Supplying and fixing of GI tubing medium grade with all fittings fixed to wall and ceiling or laid under floors /in trenches of size-20 mm Bore complete all as specified and all as directed by Engineer-in-Charge. | 50 | RM | |
| 114 | 114 | Supplying and fixing of gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 25 mm dia complete all as specified and all as directed by Engineer-in-Charge. | 1 | Each | |
| 115 | 115 | Cutting existing steel tubing for alterations or additions, Screwing existing steel tubing for alterations or additions screw on pipe to form connector done in position without taking down existing for 80 mm bore GI Pipe complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 116 | 116 | Construction of brick masonary valve pit of size 0.45mx0.45mx0.45m (internal dimension) with 100mm thick concrete in foundation PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), 50mm thick cement concrete 1:2:4 type B1(using 20mm graded crushed stone aggregate) in floor finished even and fair without using extra cement, 23cm thick brick work in cement mortar 1:4, 15mm thick plastering in cement mortar 1:4 and flush pointing in same mortar to brick work externally, 3mm thick mild steel sheet pit cover having provision of lifting handle and pit cover frame of angle iron 40x40x6mm and painting to steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer to stelll surface and excavation in soft/loose soil, returning filling and removal of surplus soil upto 50m distance complete all as specified and as directed by Engineer-In-Charge. | 1 | Each Job | |
| 117 | 117 | Supply and fixing tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings of size 40mm bore complete all as specifed and directed by Engr-In-Charge. | 330 | RM | |
| 118 | 118 | Making hole in a wall for fixing GI pipe of size 40mm bore and making good to the disturbed surfaces matching with existing complete all as specified and directed by Engr-In-Charge. | 110 | Each Job | |
| 119 | 119 | Taking down existing UNSV chlorination plant complete any type and depositing the same at MES store yard complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 120 | 120 | Taking down existing UNSV submersible pumpset 10000 gallon/hr 250 meter head and depositing the same at MES store yard complete all as specified and directed by Engr-In-Charge. | 1 | Each Set | |
| 121 | 121 | Taking down existing UNSV carefully centrifugal pumpset coupled with 5 HP motor and depositing the same at MES store yard complete all as specified and directed by Engr-In-Charge. | 1 | Each Set | |
| 122 | 122 | Supply, installation, connecting, testing and commissioning of single head adjustable Dosing system 230 voltts, 50 Hz with adjustable pressure 5kg/sq.cm, max out put 10 ltrs/hour of suitable FHP with all mandatory accessories like lead tubing connecting ferrules check valves etc including preparation tank of capacity 100 Ltrs fabricated out of FRP of suitable diameter with mounting stand as required having water Inlet line, outlet with strainer, Draining provision, Overflow, with conical bottom for sludge deposition, pot hole with cover, level gauge and agitator of rating 120 Watt, 900 RPM single phase flange mounted with plastic shaft and impeller, and including Service tank of capacity 100 ltrs fabricated out of FRP with water inlet line, Dosing pump inlet arrangement, drain provision, overflow, level gauge, Inspection port with agitator 120 Watt 900 RPM single phase flange mounted motor with plastic shaft and impeller including provision of mounting pump on lid/wall including interconnecting complete system using suitable size pipeline with supply pipe line complete all specified and directed by Engr-In-Charge. | 1 | Each | |
| 123 | 123 | Supply installation testing and commissioning of Submersible pump, electric driven 415 V, TP inside existing bore well of capacity 10,000 gallon/hr at 75 mtr head including lowering the motor inside borewell using suitable T&P complete all as specified and directed by Engr-In-Charge. | 1 | Each Job | |
| 124 | 124 | Supply and fixing, lowering submersible copper cable of size 16 Sqmm, 3 Core ,1100 volts complete all as specified and directed by Engr -in-Charge. | 100 | RM | |
| 125 | 125 | Supply and fixing pump of capacity 3.7 KW/5 HP suitable for 23.5 metre head and 14 to 8 ltr per second capacity complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 126 | 126 | Heavy Duty MS ERW column pipe as per IS 3589 as amended time to time of size 100 mm dia medium class (supplied in 3 mtr long ( 10 feet) length) both end flanged,welded including specials suitable for submersible pump having suitable cuts for passing through submersible cable including nut ,bolts & rubber gasket complete all as specified and directed by Engr-In-Charge. | 45 | RM | |
| 127 | 127 | Taking down existing UNSV Transformer 200 KVA carefully and depositing the same at MES store yard complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 128 | 128 | Supply, installation, testing and commissioning of step down transformer 11 KV/ 433 Volts (at no load) 3 Phase 50 Hz, 200 KVA, copper wound, outdoor type, oil cooled with off load tap changing arrangement of HT side to vary secondary voltage upto ± 7.5 % in step of ± 2.5% including 4 Nos of suitable size of transformer wheel complete in all respect with std. accessories and fitment confirming to IS-1180 Part-I of 2014, Dyn -11 connection in and including first filling of transformer oil upto conservator tank complete all as specified and directed by Engr-In-Charge. The salient features of Transformer shall be as follows :- (a) Transformer shall be oil immerse, naturally self cooled double wound copper, winding core type, MS radiater cooled tank complete with and including first fill of transformer oil plus 5% spare oil as per IS 335 of 1993 with test certificates with on cooling system.\n(b) Rating and diagram plates\n(c) Earthing terminals = 02 Nos\n(d) Lifting lugs.\n(e) Thermometer pocket\n(f) Air release hole with plug\n(g) Winding/Oil temperature indicator \n(h) Conservation with oil level indicator\n(j) Castors with locking provision\n(k) Silica Gel breather complete | 1 | Each | |
| 129 | 129 | Supply and laying MS Tubes of 100mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in trenches for cable protection complete all as specified and directed by Engr-In-Charge. | 10 | RM | |
| 130 | 130 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 240 sq mm 3.5 core complete all as specified and directed by Engr-In-Charge. | 100 | RM | |
| 131 | 131 | Supply and fix cable jointing kit for 1.1 KV grade cable for end termination joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 185 to 240 sqmm,Indoor/Outdoor type complete all as specified and directed by Engr-In-Charge. | 4 | Each | |
| 132 | 132 | Supply and fix cable jointing kit for 11 KV grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 70 sqmm to 120 sqmm complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 133 | 133 | Supply and fix bus bar chamber outdoor type made out of 3mm thick CRCA sheet steel factory mady duly painted with two coat of synthetic enamelled paint over a coat of red oxide primer including one no MCCB 250 amps, 4 pole, 4 Nos aluminum bus bar 400 Amps, including voltmeter range 0-500 Volts and Ammeter 0-300 Amps with suitable size of CT and phase indication LED lamps, water proof dust and vermin proof hinged and lockable doors incl rain protection cover on top and complete with copper wire,tapes, bonding to earth and painting, fixed on angle iron frame and having 4 legs 1.0 mtr long of suitable size including grouting in PCC 1:4:8, 0.5 mtr depth, complete all as specified and directed by Engr-In-Charge. Note:- This panel shall be a FRONT operated with cable entry from the bottom | 1 | Each | |
| 134 | 134 | Supply and fixing refrigerator, electric driven (single phase), capacity not less than 195 Litres complete all as specified and directed by Engr-In-Charge. | 2 | Each | |
| 135 | 135 | Supply and fixing refrigerator, electric driven (single phase), capacity not less than 300 Litres complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 136 | 136 | Supply and fix desert cooler electric driven (single phase), having nominal air flow capacity of 4000 Cum per hour (or nearest size), Steel body incluidng provision of drainage and inlet water supply connection with float valve complete all as specified and directed by Engr-In-Charge. | 1 | Each | |
| 137 | 137 | Sub main wiring with two single core of copper conductor PVC insulated cable of 2.5 Sqmm cross sectional area multi stranded drawn through in and including PVC conduit of 20 mm dia with 1.5 Sqmm single core PVC insulated copper cable as earth continuity wire complete all as specified and directed by Engr-In-Charge. | 70 | RM | |
| 138 | 138 | Supply and fixing Voltage stablizer for automatic operation single phase naturally air cooled indoor type and designed for input variation 140 V to 250 V with output voltage stablizer at 230 V with accuracy of plus minus 2.5 % and capacity of 2 KVA complete all as specified and directed by Engr-In-Charge. | 3 | Each | |
| 139 | 139 | Taking down of exiting old unsv , desert cooler, Refrigerator/ deep freezer any type and depositing the same in MES store yard GE ( AF ) complete in all respect asdirected by Engr in charge. | 4 | Each | |
| 140 | 140 | Earthing complete with copper earth plate electrode of size 600x600x3mm thick as earth electrode not less than 2.25mtr below ground level with top edge of earth plate not less than 1.50 metre below normal ground level connected to copper strip 20x3mm as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth strip protection pipe GI light grade 50mm dia from earth plate to main switch board/panel, watering pipe 20mm dia medium grade with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 with adequate quantity of charcoal dust and salt all around the earth plate including all necessary earth work in any type of soil, removing surplus excavated material all as required at site and specified in EP No 3 of SSR part I 2009 and directed by Engineer-in-charge. \n(Note:- Up to 7.5 Mtr length of GI protection pipe and copper strip shall be deemed to be included in unit rate quoted by tenderer. | 4 | Each |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
