Supply, Installation & Commissioning Of Led Light Fitting -Karnataka

Supply, Installation & Commissioning Of Led Light Fitting 1. Supplying Of 1.1 Kv Lt Ug Cable Having Aluminium Conductor Pvc Insulated, Extruded Inner Sheathed,Galvanised,Steel Strip (Except 2Cx10sq.Mm Wire Armoured) Confirming To Is 3975:1990 (No. Of Strip Indicated In Gtp) & Extruded Pvc Outer Sheathed Armoured Cable With Specified Is 1554 Part 1:1988 & Confirming To The Attached Gtp Of Group A. As Per The Direction Of Work Incharge Engineer 3.5 Core 35 Sqmm (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.4.6), 2. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refiling The Trench To The Required Ground Level And Consolidating Etc., Complete. As Per The Direction Of Work Incharge Engineer In Soil (Ordinary)(Pwd Electrical Sr 2019 20 Page No 41, Item No 6.6.1), 3. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refiling The Trench To The Required Ground Level And Consolidating Etc., Complete. As Per The Direction Of Work Incharge Engineer In Soil (Hard)(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.6.2), 4. Labour Charges For Laying Of 1.1 Kv Class Ug Cable In Existing Trench Gi Pipe / Stoneware Pipe / On Wall / On Pole As Required. As Per The Direction Of Work Incharge Engineer 25 Sqmm To 75 Sqmm (Pwd Electrical Sr 2019 20 Page No 41, Item No 6.5.2), 5. Supplying And Fiixing Of Heavy Duty Cable Glands Suitable For Ug Cable Of 1.1 Kv Class (Metal Only)45Mm Dia(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.11.4), 6. Supplying And Running Gi/Copper Conductor For Grounding And (Along With Other Wires In Conduit System Of Wiring) Using Necessary Suitable Size Clamps, Nails, Guttas/Spacers Etc..( 64 / 7.22)(Pwd Electrical Sr 2019 20 Page No 44, Item No 6.18.6) Copper Wire 8 Swg, 7. Supplying Tinned Copper Lugs And Crimping And Wiring To Terminal Point For Wire Of The Following Sizes.F) 35 Sqmm Long Barrel(Pwd Electrical Sr 2019 20 Page No 43, Item No 6.17.8, 8. Fabricating Supplying And Mounting Ms Box Made Out Swg Suitable For Floor / Wall Mounting, Fully Weather Proof With Provision For Better Heat Dissipation, Provided With Hinged Front Cover, Equipped With Tamper Proof Locking Arrangements, With Suitable Size Clamps With Necessary Cable Entry Pipe With Gland And Box Should Be Finished With 2 Coats Of Red Oxide Primer Paint And Finally Finished With Approved Colour Enameled Metal Paint Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.42.1) 14Swg, 9. Supplying Amps Rated 3Phase With Neutral Bus Bar Using Required Capacity Electrolytic Alluminium Strips Covered With Heat Shrinkable Coloured Pvc Sleeve, Mounted On Phenolic/Frp/Dmc Insulator Which Are Mounted On Powder Coated 40X6mm M.S.Flat Frame Work In Existing Panel Board. The Bus Bar Shall Have Suitable Holes For Termination Of Incoming And Outgoing Cables As Per Is Specification With Necessary Botls,Nuts And Washers Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.40.1) 100Amps 4X30x6mm Alluminium Strips, 10. Supplying And Fixing Angle Iron Frame Work Fabricated Out Of M.S. Angle Iron And M.S. Flat With Bolts, Washers Etc., And Painted With 2 Coats Of Red Oxide And Then Two Coats Of Approved Paint. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.41.2) 50X50x6mm, 11. Supplying And Fixing Microprocessor Based Electronic Timer (Without Contactor,Din Mounting Using Necessary Bolts, Nuts And Washers Etc.,.) As Per The Direction Of Work Incharge Engineer 3 120Sec. ( Pwd Electrical Sr 2019 20 Page No 32, Item No 5.47), 12. Supply And Fixing Of 4Pole Power Contactor With No/Nc Contacts On Existing Wood/Panel Board Using Necessary Bolts, Nuts, Washers And Wiring Etc., Complete With Ac-3 Rating And As Per Is 13947. As Per The Direction Of Work Incharge Engineer( ( Pwd Electrical Sr 2019 20 Page No 26, Item No 5.13.1) A) 25Amps, 13. Supplying And Fixing Moulded Case Circuit Breaker (Mccb) Over The Existing Wood/Panel Board Using Necessary Screws, Bolts, Nuts And Wiring Complete. Protection Of Overload And Short Circuit With Thermal Magnetic/Microprocessed Release And Earth Fault As Per Is 13947. ( Icu = Ics) (Pwd Electrical Sr 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25Ka., 14. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 63 Amps Sp, 15. Supplying Pvc/Gi Flexible Conduit Pipe50mm Fixing On Surface Over Inverted Tapered Wooden Plugs Or Phill Plugs Or Rawl Plugs And Clamped Using Heavy Gauge Saddles At An Interval Of 300Mm Using Nf Screws And On Either End Of The Pipe Terminated Completely(Pwd Electrical Sr 2019 20, Pgno.3, It.No.1.9.5 ), 16. Supplying And Drawing Flexible Multicore Cable Manufactured With Electrolytic Grade Flexible Copper With Low Conductor Confirming To Is:8130 1984 And (Virgin) Pvc Insulation Sheathed Suitable For Working Voltage Upto 1100Volts As Per Is 694:1990(Pwd Electrical Sr 2019 20, Pgno.6, It.No.2.5.7) 8C X 2.5Sq.Mm, 17. Supplying, And Fixing Of Hot Dip Galvanized M.S.Bracket Suitable For Out Door Luminaries And Mounted On Octagonal Pole Using Necessary Bolts, Nuts Etc., Complete(Pwd Electrical Sr 2019 20, Pgno.16, It.No.4.7.5) Double Arm Bracket With 1500Mm Standard 40/50Mm Dia, 18. Supplying And Fixing Electronic Trivector Meter (Etv) Suitable For Operation Lt Operation And Ct Operated Meter In Polycarbonate Body In Class 0.5 Accuracy As Per Is 14697 And Completely Wired (Pwd Electrical Sr 2019 20, Pgno.29, It.No.5.31), 19. Supplying And Fixing Of Class A (Medium Duty) Gi Pipe Of Wall Thickness Not Less Than 3.25Mm On Pole/Wall/Drain Crossing With Necessary Clamping Arrangements For Ug Cable Of 1.1 Kv. 65Mm (Pwd Electrical Sr 2019 20, Pgno.42, It.No.6.9.3), 20. Providing And Laying In Position 100Mm Dia Stone Ware Pipe In Existing Trench. (Pwd Electrical Sr 2019 20, Pgno.41, It.No.6.8), 21. Supply Of Led Floodlight Luminaire With Pressure Die Cast Aluminium Housing Body For Optimal Thermal Dissipation. Lamp Compartment Comprising Of Anti Glare Clear Diffuser With Injection Moulded Polycarbonate/Clear Glass Material, Delivering Superior Light Output. Rated Life Burning Hrs 50000 Hr @ Lumen Maintenance Of 70%, Cct > 5500K, Ip 66 Optical And Electrical Compartment & Impact Resistance Of Complete Luminaire > Ik08. Power Factor >0.9 With Mains, Surge Protection Min 5Kv Along With Over Voltage/ Overload, Short Circuit/ Miss Wiring Protection. Compatible For Pole Mouting With Outer Dia Of 40Mm To 50Mm.Universal Voltage Driver To Operate Wide Voltage Range From 100V To 270V 50/60Hz Application. Compliance To Is 10322/ Iec 60598, Lm 79 & Lm 80 Adherence With Rohs. Ul Approved Mcpcb. Top Access Street Light With Single Screw To Ensure Ease Of Maintenance At The Sight Site Location With Minimized Minimal Tools. Led Light Fixture With W System Power Consumption. Led Efficiency>130Lm/W, Nominal Cri >75. Luminaire Manufacturer Should Have Inhouse Facility Accredited By Nabl/Cpri & Any Government Certified Agency & Design & Development Facility Certified By Iso 9001:2008 . Housing With Supplier Word Mark /Name Shall Be Engraved / Embossing On The Die Cast Housing/ Body Part. Warranty Of 2 Years Against Any Manufacturing Defect Working Under Standard Electrical Conditions As Mentioned Above Should Be Given By Led Manufacturer & Cree/Nichia/ Lumileds/Osram Make Led Source. (Pwd Electrical Sr 2019 20 P.No 67 It.No 12.9.4) Led Floodlight 150W, 22. Supplying And Running Gi/Copper Conductor For Grounding And (Along With Other Wires In Conduit System Of Wiring) Using Necessary Suitable Size Clamps, Nails, Guttas/Spacers Etc..( 64 / 7.22)(Pwd Electrical Sr 2019 20 Page No 44, Item No 6.18.6) Copper Wire 8 Swg, 23. Supplying Tinned Copper Lugs And Crimping And Wiring To Terminal Point For Wire Of The Following Sizes.F) 35 Sqmm Long Barrel(Pwd Electrical Sr 2019 20 Page No 43, Item No 6.17.8, 24. Supplying Amps Rated 3Phase With Neutral Bus Bar Using Required Capacity Electrolytic Alluminium Strips Covered With Heat Shrinkable Coloured Pvc Sleeve, Mounted On Phenolic/Frp/Dmc Insulator Which Are Mounted On Powder Coated 40X6mm M.S.Flat Frame Work In Existing Panel Board. The Bus Bar Shall Have Suitable Holes For Termination Of Incoming And Outgoing Cables As Per Is Specification With Necessary Botls,Nuts And Washers Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.40.1) 100Amps 4X30x6mm Alluminium Strips, 25. Supplying And Fixing Microprocessor Based Electronic Timer (Without Contactor,Din Mounting Using Necessary Bolts, Nuts And Washers Etc.,.) As Per The Direction Of Work Incharge Engineer 3 120Sec. ( Pwd Electrical Sr 2019 20 Page No 32, Item No 5.47), 26. Supply And Fixing Of 4Pole Power Contactor With No/Nc Contacts On Existing Wood/Panel Board Using Necessary Bolts, Nuts, Washers And Wiring Etc., Complete With Ac 3 Rating And As Per Is 13947. As Per The Direction Of Work Incharge Engineer( ( Pwd Electrical Sr 2019 20 Page No 26, Item No 5.13.1) A) 25Amps, 27. Supplying And Fixing Moulded Case Circuit Breaker (Mccb) Over The Existing Wood/Panel Board Using Necessary Screws, Bolts, Nuts And Wiring Complete. Protection Of Overload And Short Circuit With Thermal Magnetic/Microprocessed Release And Earth Fault As Per Is 13947. ( Icu = Ics) (Pwd Electrical Sr 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25Ka., 28. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 6 32Amps Sp, 29. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 63 Amps Sp, 30. Supplying & Fixing Of Porcelain Fuse Channel With Cut Out On Existing Wooden/Panel Using Necessary Nuts, Bolts And Washers(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.7.2) 32 Amps, 31. Supplying & Fixing Of Porcelain Fuse Channel With Cut Out On Existing Wooden/Panel Using Necessary Nuts, Bolts And Washers(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.7.2) 63 Amps, 32. Supplying And Fiixing Of Heavy Duty Cable Glands Suitable For Ug Cable Of 1.1 Kv Class (Metal Only)45Mm Dia(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.11.5 & 6.11.8) 50Mm Dia, 33. Supplying And Fiixing Of Heavy Duty Cable Glands Suitable For Ug Cable Of 1.1 Kv Class (Metal Only)45Mm Dia(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.11.5 & 6.11.8) 10Mm Dia, 34. Supplying Of Switch Disconnector Fuse Unit (Tpn) Hrc Type (But Without Hrc Fuses). With Ac-23A Duty And As Per Is 13947.(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.8.1) 63 Amps, 35. Supplying Of Switch Disconnector Fuse Unit (Tpn) Hrc Type (But Without Hrc Fuses). With Ac 23A Duty And As Per Is 13947.(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.8.1) 125 Amps, 36. Supplying And Fixing Hrc Fuse Units Base On Existing Switch/ Panel Board.It.No.5.8.1(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.9.2) 32 To 63 Amps, 37. Supplying And Fixing Hrc Fuse Link On Existing Switch Fuse Base With Watt Loss As Per Is 13703.(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.10.0) Up To 63 Amps, 38. Wiring For Lighting/Power Circuit Using One Of Frls Pvc Insulated 1100V Grade, Multistrand Copper Wire With Low Conductor Resistance Single Core In Open Or Concealed System Of Wiring 4 Sqmm, 39. Supplying Of 1.1 Kv Lt Ug Cable Having Aluminium Conductor Pvc Insulated, Extruded Inner Sheathed, Galvanised, Steel Strip (Except 2Cx10sq.Mm Wire Armoured) Confirming To Is 3975:1990 (No. Of Strip Indicated In Gtp) & Extruded Pvc Outer Sheathed Armoured Cable With Specified Is 1554 Part 1:1988 & Confirming To The Attached Gtp Of Group A. As Per The Direction Of Work Incharge Engineer 3.5 Core 35 Sqmm (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.4.6), 40. Supplying Of 1.1 Kv Lt Ug Cable Having Aluminium Conductor Pvc Insulated, Extruded Inner Sheathed, Galvanised, Steel Strip (Except 2Cx10sq.Mm Wire Armoured) Confirming To Is 3975:1990 (No. Of Strip Indicated In Gtp) & Extruded Pvc Outer Sheathed Armoured Cable With Specified Is 1554 Part 1:1988 & Confirming To The Attached Gtp Of Group A. As Per The Direction Of Work Incharge Engineer 3.5 Core 25 Sqmm(Pwd Electrical Sr 2019 20 Page No 40, Item No 6.4.5), 41. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refiling The Trench To The Required Ground Level And Consolidating Etc., Complete. As Per The Direction Of Work Incharge Engineer In Soil (Ordinary)(Pwd Electrical Sr 2019 20 Page No 41, Item No 6.6.1), 42. Labour Charges For Laying Of 1.1 Kv Class Ug Cable In Existing Trench Gi Pipe / Stoneware Pipe / On Wall / On Pole As Required. As Per The Direction Of Work Incharge Engineer 25 Sqmm To 75 Sqmm (Pwd Electrical Sr 2019 20 Page No 41, Item No 6.5.2), 43. Ksrb 2 2 : Earthwork Excavation By Manual Means For Foundation Of Buildings, Water Supply And Sanitary Lines And Electrical Conduits Etc, Either In Pits Or In Trenches 1.5M And Above In Width, In Soil Not Exceeding 1.5 M. In Depth Including Dressing The Bottom And Sides Of Pits And Trenches, Stacking The Excavated Soil Clear From Edges Of Excavation With Lead Upto 50 M. Including Breaking Of Clods Complete As Per Specifications In Ordinary Soil (Pwd Civil Sr 2018 19, Pg.No.6, It.No.2.3) For Pole, 44. Ksrb 4.2.2 : Providing And Laying In Position Reinforced Cement Concrete Of Design Mix M20 With Opc @ 320Kgs, With 20Mm And Down Size Graded Granite Metal Coarse Aggregates @0.69Cum And Fine Aggregtes @ 0.460 Cum, With Super Plasticisers @ 3 Liters Confirming To Is 9103 1999 Reaffirmed 2008, Machine Mixed, Concrete Laid In Layers Not Exceeding 15 Cms Thick, Vibrated For All Works In Foundation For Footings, Pedastals, Retaining Walls, Return Walls, Walls (Any Thickness) Including Attached Pilasters, Columnspillars, Posts, Struts, Buttresses, Bed Blocks, Anchor Blocks & Plinths Etc., Including Cost Of All Materials, Labour, Hom Curing, Complete But Excluding Cost Of Reinforcement As Per Specifications.Specification No. Kbs 4.1, 4.6 (Pwd Civil Sr 2018 19, Pg.No.13, It.No.4.11) For Pole, 45. Supply And Installation / Fixing / Provision Of Pole Box With Hrc Fuse / Mcb Provision And Suitable Connector / Terminal For 3 Ph / 1 Ph Connections With Loop-In & Loop-Out Terminals For 10 Sqmm / 25 Sqmm 3.5 C Al/Ar / Cu/Ar Cable And Branch Out 2.5 Sqmm 2 Core Al/Cu Pvc Insulated Cable, Enclosed In A Thermoplastic, Polystyrene Enclosure, Which Should Be Shock Proof, Safe, Ip65(Weather Proof), Rust Proof, Dust Proof, Water Proof Having Internally Embedded Gasket With Provision For Cable Entry Through Ip65 Thermoplastic, Polyamide Glands And/Or Grommets.200X200x98mm(Pwd Electrical Sr 2019 20 Page No 31 Item No 5.43.1), 46. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 63 Amps Sp, 47. Supplying, Fixing, Wiring, Earth Electrode For Grounding Conduits, I.C. Cutouts And Other Equipments On The Meter Board Using 40Mm Dia 2.90Mm Thick Gi Pipe 2.5 Mtr Long Buried In A Pit The Pit Should Be Filled With Equal Proprotion Of Salt And Charcoal 150Mm Alround The Pipe To Complete Depth. The Connection From The Pipe To The Conduit Etc, Is To Be Established Through Gi Wire Of Size As Per Isi Specification 7.3.3. Of Is 732 Using 12Mm Dia Bolts, Nuts, Washers And Checknuts Etc, The Pipe Shall Have 16 Through Holes Of 122 Mm Dia ( 55 / 7.1) (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.1), 48. Supplying Pvc/Gi Flexible Conduit Pipe50mm Fixing On Surface Over Inverted Tapered Wooden Plugs Or Phill Plugs Or Rawl Plugs And Clamped Using Heavy Gauge Saddles At An Interval Of 300Mm Using Nf Screws And On Either End Of The Pipe Terminated Completely(Pwd Electrical Sr 2019 20, Pgno.3, It.No.1.9.5 ), 49. Fabricating, Supplying And Erection Of Mtrs Long Hot Dip Galvanized Conical Pole With Bsen 10025 Grade S355jo Steel Plate For Shaft, Is 2062 For Base Plate With Door Opening Arrangements, Including Suitable Boards, Bakelite Sheet And Mcbs As Per Is Specifications Suitable To Withstand The Wind Speed Of 47 M/Sec For Mtrs Pole In Single Section And Single Joint Welded As Per Is 9595/Is 10178Aws Having Dimensions Bottom Mm, Top Mm With 3Mm Thick, Suitable Base Plate And 4Nos Of Long J Bolts Along With Template And The Pole Shall Be Hot Dip Galvanized In Single Dipping With Not Less Than 65Micron As Per Astm A123 And 153 Etc.,(Excluding Foundation) As Per Drawing Appended.(Pwd Electrical Sr 2019 20, Pgno.14, It.No.4.4.8) 10 Meters Top 75Mm And Bottom 165 Mm Dia, 50. Supplying And Fixing Of Mm Dia Class A Gi Pipe Bracket Up To 2 Mtrs Long Bent At Suitable Angle And Fixing To This Bracket 1X40/2X40 Watts Fluorescent Tube Street Light Fitting Of All Capacities To Gi Or Ci Or Rail Or Rcc Pole / Wall Using Suitable Clamps, Bolts, And Nuts And Wiring Using Suitable Capacity Wires. (Pwd Electrical Sr 2019 20, Pgno.79, It.No.14.1.2) Using 32Mm Dia G.I.Pipe, 51. Supplying And Fixing Telescopic M.S. Bracket Fabricated By Using 0.5M Length 4 Dia Telescopic M. S. Pipe, With 2 Dia 1.5M Long M. S. Bracket And Are Welded With Suitable Angle, Using 6Mm Thick M. S. Sheet, Grip Bolts & Nuts, As Required, Suitable For 9 To 12 Mtrs. M. S. Tubular Pole, With Necessary Two Coats Of Painting, With All Other Accessories(Pwd Electrical Sr 2019 20, Pgno.79, It.No.14.4.2) Single Bracket 2 Mtr. Length, 52. Supplying And Drawing Flexible Multicore Cable Manufactured With Electrolytic Grade Flexible Copper With Low Conductor Confirming To Is:8130 1984 And (Virgin) Pvc Insulation Sheathed Suitable For Working Voltage Upto 1100Volts As Per Is 694:1990(Pwd Electrical Sr 2019 20, Pgno.6, It.No.2.5.7) 2C X 2.5Sq.Mm, 53. Supply Of Led Floodlight Luminaire With Pressure Die Cast Aluminium Housing Body For Optimal Thermal Dissipation. Lamp Compartment Comprising Of Anti Glare Clear Diffuser With Injection Moulded Polycarbonate/Clear Glass Material, Delivering Superior Light Output. Rated Life Burning Hrs 50000 Hr @ Lumen Maintenance Of 70%, Cct > 5500K, Ip 66 Optical And Electrical Compartment & Impact Resistance Of Complete Luminaire > Ik08. Power Factor >0.9 With Mains, Surge Protection- Min 5Kv Along With Over Voltage/ Overload, Short Circuit/ Miss-Wiring Protection. Compatible For Pole Mouting With Outer Dia Of 40Mm To 50Mm. Led Floodlight 150W, 54. Fabricating Supplying And Mounting Ms Box Made Out Swg Suitable For Floor / Wall Mounting, Fully Weather Proof With Provision For Better Heat Dissipation, Provided With Hinged Front Cover, Equipped With Tamper Proof Locking Arrangements, With Suitable Size Clamps With Necessary Cable Entry Pipe With Gland And Box Should Be Finished With 2 Coats Of Red Oxide Primer Paint And Finally Finished With Approved Colour Enameled Metal Paint Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.42.1) For Speaker Box In Mdf, 55. Supplying Of Multicoloure ( Min 7 Colours) Led Underwater Luminary With Corrosion Resistent ( Ip 68), 36Watt Power Led, Body Made Up Of Aluminium Or Stainless Steel 304 With Suitable Multicoloure Controller And Driver Including Fixing In Water Channels On Non Corrosive Metal Angles Whose Base Fixed In M20 Grade Cement Concrete With All Lead And Lifts And As Per The Direction Of Engineer Incharge.( Lowest Quotation Rate), 56. Ahuja Introduces A 700 Watts Professional 2 Way Pa Speaker System With Exceptional Lf Response, Tremendous Efficiency And Unmatched Intelligible Sound. Two 15 High Performance Lf Transducers And A High Frequency Titanium Compression Horn Driver Housed In An Acoustically Treated Bass Reflex Trapezoidal Enclosure With Ultra-Modern Paint Finish.Sturdy And Aesthetically Designed Metal Grill Lends Both Protection To The Speakers As Well As Superb Looks To The Cabinet.Well Designed Heavy Duty Metal Complete As Per The Specification ( Lowest Quotation Rate) Mdf, 57. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refilling The Trench To The Required Ground Level And Consolidating Etc., Complete.(As Per Civil Sr Ksrb I 2, P 7) In Soil (Ordinary) Pwd El Sr 2019 20 No: 6.6.1 S1, S2 & S3 Terrace, 58. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refilling The Trench To The Required Ground Level And Consolidating Etc., Complete.(As Per Civil Sr Ksrb I 2, P 7) In Soil (Ordinary) Pwd El Sr 2019 20 No: 6.6.1 N1, N2 & N3 Errace, 59. Supply Of Led Pole Mounting Type Post Top Lantern With Pressure Die Cast Aluminium Housing Body For Optimal Thermal Dissipation. Lamp Compartment Comprising Of Anti Glare Clear Diffuser With Injection Moulded Polycarbonate/ Clear Glass Material, Delivering Superior Light Output Rated Life Burning Hrs 50000 Hr @ Lumen Maintenance Of 70%, Cct > 5500K, Ip 66 Optical And Electrical Compartment & Impact Resistance Of Complete Luminaire > Ik08. Power Factor >0.9 With Mains, Surge Protection Min 5Kv Along With Over Voltage/Overload, Short Circuit/ Miss Wiring Protection. Compatible For Pole Mounting With Outer Dia Of 40Mm To 50Mm. Universal Voltage Driver To Operate Wide Voltage Range From 100V To 270V 50/60Hz Application. Compliance To Is 10322/Iec 60598, Lm 79 & Lm 80 Adherence With Rohs. Ul Approved Mcpcb . Led Efficiency>130Lm/W, Nominal Cri >75. Luminaire Manufacturer Should Have Inhouse Facility Accredited By Nabl/Cpri & Any Government Certified Agency & Design & Development Facility Certified By Iso 9001:2008. Housing With Supplier Word Mark /Name Shall Be Engraved / Embossing On The Die Cast Housing/ Body Part. Warranty Of 2 Years Against Any Manufacturing Defect Working Under Standard Electrical Conditions As Mentioned Above Should Be Given By Led Manufacturer & Cree/Nichia/ Lumileds/Osram Make Led Source. Pwd El Sr 2019 20 No: 12.7.2 South Garden, 60. Supply Of Led Pole Mounting Type Post Top Lantern With Pressure Die Cast Aluminium Housing Body For Optimal Thermal Dissipation. Lamp Compartment Comprising Of Anti Glare Clear Diffuser With Injection Moulded Polycarbonate/ Clear Glass Material, Delivering Superior Light Output Rated Life Burning Hrs 50000 Hr @ Lumen Maintenance Of 70%, Cct > 5500K, Ip 66 Optical And Electrical Compartment & Impact Resistance Of Complete Luminaire > Ik08. Power Factor >0.9 With Mains, Surge Protection Min 5Kv Along With Over Ltage/Overload, Short Circuit/ Miss Wiring Protection. Compatible For Pole Mounting With Outer Dia Of 40Mm To 50Mm. Universal Voltage Driver To Operate Wide Voltage Range From 100V To 270V 50/60Hz Application. Compliance To Is 10322/Iec 60598, Lm 79 & Lm 80 Adherence With Rohs. Ul Approved Mcpcb . Led Efficiency>130Lm/W, Nominal Cri >75. Luminaire Manufacturer Should Have Inhouse Facility Accredited By Nabl/Cpri & Any Government Certified Agency & Design & Development Facility Certified By Iso 9001:2008. Housing With Supplier Word Mark /Name Shall Be Engraved / Embossing On The Die Cast Housing/ Body Part. Warranty Of 2 Years Against Any Manufacturing Defect Working Under Standard Electrical Conditions As Mentioned Above Should Be Given By Led Manufacturer & Cree/Nichia/ Lumileds/Osram Make Led Source. Pwd El Sr 2019 20 No: 12.7.2 North Garden, 61. Supplying And Drawing Flexible Multicore Cable Manufactured With Electrolytic Grade Flexible Copper With Low Conductor Confirming To Is:8130 1984 And (Virgin) Pvc Insulation Sheathed Suitable For Working Voltage Upto 1100Volts As Per Is 694:1990 Pwd El Sr 2019 20 No: 2.5.23 4C X 6Sq.Mm,

INR 550 /-

INR 90000.0 /-

Refer document

Sl No	Item Code	Item Name	Item Description	Unit	Quantity
1	01/TEND/2020/RK/472/01	Supplying of 1.1 KV LT UG cable having aluminium conductor PVC insulated, extruded inner sheathed,galvanised,steel strip (except 2CX10Sq.mm wire armoured) confirming to IS 3975:1990 (No. of Strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS 1554 Part 1:1988 & confirming to the attached GTP of GROUP A. as per the direction of work incharge engineer 3.5 core 35 sqmm (PWD Electrical SR 2019 20 Page No 40, Item No 6.4.6)	Specification: As specified in the tender document.	Nos	600
2	01/TEND/2020/RK/472/02	Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. as per the direction of work incharge engineer In soil (ordinary)(PWD Electrical SR 2019 20 Page No 41, Item No 6.6.1)	Specification: As specified in the tender document.	Nos	550
3	01/TEND/2020/RK/472/03	Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. as per the direction of work incharge engineer In soil (hard)(PWD Electrical SR 2019 20 Page No 42, Item No 6.6.2)	Specification: As specified in the tender document.	Nos	50
4	01/TEND/2020/RK/472/04	Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required. as per the direction of work incharge engineer 25 sqmm to 75 sqmm (PWD Electrical SR 2019 20 Page No 41, Item No 6.5.2)	Specification: As specified in the tender document.	Nos	600
5	01/TEND/2020/RK/472/05	Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only)45mm dia(PWD Electrical SR 2019 20 Page No 42, Item No 6.11.4)	Specification: As specified in the tender document.	Nos	12
6	01/TEND/2020/RK/472/06	Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc..( 64 / 7.22)(PWD Electrical SR 2019 20 Page No 44, Item No 6.18.6) Copper wire 8 SWG	Specification: As specified in the tender document.	Nos	30
7	01/TEND/2020/RK/472/07	Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.f) 35 sqmm Long Barrel(PWD Electrical SR 2019 20 Page No 43, Item No 6.17.8	Specification: As specified in the tender document.	Nos	240
8	01/TEND/2020/RK/472/08	Fabricating supplying and mounting MS box made out SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.42.1) 14SWG	Specification: As specified in the tender document.	Nos	300000
9	01/TEND/2020/RK/472/09	Supplying amps rated 3phase with neutral bus bar using required capacity electrolytic alluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary botls,nuts and washers etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.40.1) 100Amps 4x30x6mm Alluminium Strips	Specification: As specified in the tender document.	Nos	4
10	01/TEND/2020/RK/472/10	Supplying and fixing angle iron frame work fabricated out of M.S. angle iron and M.S. flat with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. (PWD Electrical SR 2019 20 Page No 30, Item No 5.41.2) 50X50X6mm	Specification: As specified in the tender document.	Nos	30
11	01/TEND/2020/RK/472/11	Supplying and fixing Microprocessor based Electronic timer (without contactor,Din Mounting using necessary bolts, nuts and washers etc.,.) as per the direction of work incharge engineer 3 120sec. ( PWD Electrical SR 2019 20 Page No 32, Item No 5.47)	Specification: As specified in the tender document.	Nos	6
12	01/TEND/2020/RK/472/12	Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS 13947. as per the direction of work incharge engineer( ( PWD Electrical SR 2019 20 Page No 26, Item No 5.13.1) a) 25Amps	Specification: As specified in the tender document.	Nos	12
13	01/TEND/2020/RK/472/13	Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Microprocessed release and Earth Fault as per IS 13947. ( Icu = Ics) (PWD Electrical SR 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25kA.	Specification: As specified in the tender document.	Nos	6
14	01/TEND/2020/RK/472/14	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 63 Amps SP	Specification: As specified in the tender document.	Nos	6
15	01/TEND/2020/RK/472/15	Supplying PVC/GI flexible conduit pipe50mm fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely(PWD Electrical SR 2019 20, PgNo.3, It.No.1.9.5 )	Specification: As specified in the tender document.	Nos	60
16	01/TEND/2020/RK/472/16	Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS 694:1990(PWD Electrical SR 2019 20, PgNo.6, It.No.2.5.7) 8C X 2.5Sq.mm	Specification: As specified in the tender document.	Nos	200
17	01/TEND/2020/RK/472/17	Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete(PWD Electrical SR 2019 20, PgNo.16, It.No.4.7.5) Double Arm Bracket with 1500mm Standard 40/50MM dia	Specification: As specified in the tender document.	Nos	36
18	01/TEND/2020/RK/472/18	Supplying and fixing Electronic Trivector Meter (ETV) suitable for operation LT operation and CT operated meter in polycarbonate body in class 0.5 accuracy as per IS 14697 and completely wired (PWD Electrical SR 2019 20, PgNo.29, It.No.5.31)	Specification: As specified in the tender document.	Nos	6
19	01/TEND/2020/RK/472/19	Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV. 65mm (PWD Electrical SR 2019 20, PgNo.42, It.No.6.9.3)	Specification: As specified in the tender document.	Nos	60
20	01/TEND/2020/RK/472/20	Providing and laying in position 100mm dia stone ware pipe in existing trench. (PWD Electrical SR 2019 20, PgNo.41, It.No.6.8)	Specification: As specified in the tender document.	Nos	180
21	01/TEND/2020/RK/472/21	Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection Min 5KV along with Over voltage/ Overload, short circuit/ miss wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm.Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with W System Power consumption. LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. (PWD Electrical SR 2019 20 P.No 67 It.No 12.9.4) LED Floodlight 150W	Specification: As specified in the tender document.	Nos	65
22	01/TEND/2020/RK/472/22	Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc..( 64 / 7.22)(PWD Electrical SR 2019 20 Page No 44, Item No 6.18.6) Copper wire 8 SWG	Specification: As specified in the tender document.	Nos	80
23	01/TEND/2020/RK/472/23	Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.f) 35 sqmm Long Barrel(PWD Electrical SR 2019 20 Page No 43, Item No 6.17.8	Specification: As specified in the tender document.	Nos	50
24	01/TEND/2020/RK/472/24	Supplying amps rated 3phase with neutral bus bar using required capacity electrolytic alluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary botls,nuts and washers etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.40.1) 100Amps 4x30x6mm Alluminium Strips	Specification: As specified in the tender document.	Nos	10
25	01/TEND/2020/RK/472/25	Supplying and fixing Microprocessor based Electronic timer (without contactor,Din Mounting using necessary bolts, nuts and washers etc.,.) as per the direction of work incharge engineer 3 120sec. ( PWD Electrical SR 2019 20 Page No 32, Item No 5.47)	Specification: As specified in the tender document.	Nos	15
26	01/TEND/2020/RK/472/26	Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC 3 Rating and as per IS 13947. as per the direction of work incharge engineer( ( PWD Electrical SR 2019 20 Page No 26, Item No 5.13.1) a) 25Amps	Specification: As specified in the tender document.	Nos	16
27	01/TEND/2020/RK/472/27	Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Microprocessed release and Earth Fault as per IS 13947. ( Icu = Ics) (PWD Electrical SR 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25kA.	Specification: As specified in the tender document.	Nos	35
28	01/TEND/2020/RK/472/28	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 6 32Amps SP	Specification: As specified in the tender document.	Nos	50
29	01/TEND/2020/RK/472/29	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 63 Amps SP	Specification: As specified in the tender document.	Nos	50
30	01/TEND/2020/RK/472/30	Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers(PWD Electrical SR 2019 20, PgNo.25, It.No.5.7.2) 32 Amps	Specification: As specified in the tender document.	Nos	16
31	01/TEND/2020/RK/472/31	Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers(PWD Electrical SR 2019 20, PgNo.25, It.No.5.7.2) 63 Amps	Specification: As specified in the tender document.	Nos	25
32	01/TEND/2020/RK/472/32	Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only)45mm dia(PWD Electrical SR 2019 20 Page No 42, Item No 6.11.5 & 6.11.8) 50mm dia	Specification: As specified in the tender document.	Nos	50
33	01/TEND/2020/RK/472/33	Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only)45mm dia(PWD Electrical SR 2019 20 Page No 42, Item No 6.11.5 & 6.11.8) 10mm dia	Specification: As specified in the tender document.	Nos	50
34	01/TEND/2020/RK/472/34	Supplying of Switch disconnector fuse unit (TPN) HRC type (but without HRC fuses). With AC-23A duty and as per IS 13947.(PWD Electrical SR 2019 20, PgNo.25, It.No.5.8.1) 63 Amps	Specification: As specified in the tender document.	Nos	100
35	01/TEND/2020/RK/472/35	Supplying of Switch disconnector fuse unit (TPN) HRC type (but without HRC fuses). With AC 23A duty and as per IS 13947.(PWD Electrical SR 2019 20, PgNo.25, It.No.5.8.1) 125 Amps	Specification: As specified in the tender document.	Nos	50
36	01/TEND/2020/RK/472/36	Supplying and fixing HRC fuse units base on existing switch/ panel board.It.No.5.8.1(PWD Electrical SR 2019 20, PgNo.25, It.No.5.9.2) 32 to 63 Amps	Specification: As specified in the tender document.	Nos	100
37	01/TEND/2020/RK/472/37	Supplying and fixing HRC fuse link on existing switch fuse base with watt loss as per IS 13703.(PWD Electrical SR 2019 20, PgNo.25, It.No.5.10.0) Up to 63 Amps	Specification: As specified in the tender document.	Nos	60
38	01/TEND/2020/RK/472/38	Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring 4 sqmm	Specification: As specified in the tender document.	Nos	200
39	01/TEND/2020/RK/472/39	Supplying of 1.1 KV LT UG cable having aluminium conductor PVC insulated, extruded inner sheathed, galvanised, steel strip (except 2CX10Sq.mm wire armoured) confirming to IS 3975:1990 (No. of Strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS 1554 Part 1:1988 & confirming to the attached GTP of GROUP A. as per the direction of work incharge engineer 3.5 core 35 sqmm (PWD Electrical SR 2019 20 Page No 40, Item No 6.4.6)	Specification: As specified in the tender document.	Nos	200
40	01/TEND/2020/RK/472/40	Supplying of 1.1 KV LT UG cable having aluminium conductor PVC insulated, extruded inner sheathed, galvanised, steel strip (except 2CX10Sq.mm wire armoured) confirming to IS 3975:1990 (No. of Strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS 1554 Part 1:1988 & confirming to the attached GTP of GROUP A. as per the direction of work incharge engineer 3.5 core 25 sqmm(PWD Electrical SR 2019 20 Page No 40, Item No 6.4.5)	Specification: As specified in the tender document.	Nos	50
41	01/TEND/2020/RK/472/41	Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. as per the direction of work incharge engineer In soil (ordinary)(PWD Electrical SR 2019 20 Page No 41, Item No 6.6.1)	Specification: As specified in the tender document.	Nos	250
42	01/TEND/2020/RK/472/42	Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required. as per the direction of work incharge engineer 25 sqmm to 75 sqmm (PWD Electrical SR 2019 20 Page No 41, Item No 6.5.2)	Specification: As specified in the tender document.	Nos	250
43	01/TEND/2020/RK/472/43	KSRB 2 2 : Earthwork excavation by manual means for foundation of buildings, water supply and sanitary lines and electrical conduits etc, either in pits or in trenches 1.5m and above in width, in soil not exceeding 1.5 m. in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m. including breaking of clods complete as per specifications in ordinary soil (PWD Civil SR 2018 19, Pg.No.6, It.No.2.3) For Pole	Specification: As specified in the tender document.	Nos	2
44	01/TEND/2020/RK/472/44	KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of Design Mix M20 with OPC @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to IS 9103 1999 reaffirmed 2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnspillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM curing, complete but excluding cost of reinforcement as per specifications.Specification No. KBS 4.1, 4.6 (PWD Civil SR 2018 19, Pg.No.13, It.No.4.11) For Pole	Specification: As specified in the tender document.	Nos	3
45	01/TEND/2020/RK/472/45	Supply and Installation / Fixing / Provision of Pole box with HRC Fuse / MCB provision and suitable connector / terminal for 3 Ph / 1 Ph connections with Loop-In & Loop-Out terminals for 10 Sqmm / 25 Sqmm 3.5 C Al/Ar / Cu/Ar Cable and branch out 2.5 Sqmm 2 core Al/Cu PVC Insulated cable, enclosed in a Thermoplastic, Polystyrene enclosure, which should be shock proof, safe, IP65(Weather Proof), rust proof, dust proof, water proof having Internally Embedded Gasket with provision for cable entry through IP65 Thermoplastic, polyamide glands and/or grommets.200x200x98mm(PWD Electrical SR 2019 20 Page No 31 Item No 5.43.1)	Specification: As specified in the tender document.	Nos	10
46	01/TEND/2020/RK/472/46	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 63 Amps SP	Specification: As specified in the tender document.	Nos	2
47	01/TEND/2020/RK/472/47	Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia ( 55 / 7.1) (PWD Electrical SR 2019 20 Page No 40, Item No 6.1)	Specification: As specified in the tender document.	Nos	2
48	01/TEND/2020/RK/472/48	Supplying PVC/GI flexible conduit pipe50mm fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely(PWD Electrical SR 2019 20, PgNo.3, It.No.1.9.5 )	Specification: As specified in the tender document.	Nos	50
49	01/TEND/2020/RK/472/49	Fabricating, supplying and erection of Mtrs long hot dip Galvanized Conical pole with BSEN 10025 grade S355JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/sec for Mtrs pole in single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom mm, top mm with 3mm thick, suitable base plate and 4Nos of long J bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM A123 and 153 etc.,(excluding foundation) as per drawing appended.(PWD Electrical SR 2019 20, PgNo.14, It.No.4.4.8) 10 meters Top 75mm and bottom 165 mm dia	Specification: As specified in the tender document.	Nos	10
50	01/TEND/2020/RK/472/50	Supplying and Fixing of mm dia class A GI pipe bracket up to 2 Mtrs long bent at suitable angle and fixing to this bracket 1x40/2x40 watts fluorescent tube street light fitting of all capacities to GI or CI or rail or RCC pole / wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires. (PWD Electrical SR 2019 20, PgNo.79, It.No.14.1.2) Using 32mm dia G.I.Pipe	Specification: As specified in the tender document.	Nos	10
51	01/TEND/2020/RK/472/51	Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4 dia telescopic M. S. pipe, with 2 dia 1.5m long M. S. bracket and are welded with suitable angle, using 6mm thick M. S. sheet, grip bolts & nuts, as required, suitable for 9 to 12 Mtrs. M. S. tubular pole, with necessary two coats of painting, with all other accessories(PWD Electrical SR 2019 20, PgNo.79, It.No.14.4.2) Single bracket 2 Mtr. Length	Specification: As specified in the tender document.	Nos	10
52	01/TEND/2020/RK/472/52	Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS 694:1990(PWD Electrical SR 2019 20, PgNo.6, It.No.2.5.7) 2C X 2.5Sq.mm	Specification: As specified in the tender document.	Nos	100
53	01/TEND/2020/RK/472/53	Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. LED Floodlight 150W	Specification: As specified in the tender document.	Nos	12
54	01/TEND/2020/RK/472/54	Fabricating supplying and mounting MS box made out SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.42.1) For Speaker Box In MDF	Specification: As specified in the tender document.	Nos	200000
55	01/TEND/2020/RK/472/55	Supplying of Multicoloure ( Min 7 Colours) LED Underwater Luminary with Corrosion resistent ( IP 68), 36watt power LED, body made up of Aluminium or Stainless steel 304 with suitable multicoloure controller and driver including fixing in water channels on non corrosive metal angles whose base fixed in M20 grade cement concrete with all lead and lifts and as per the direction of engineer incharge.( Lowest Quotation rate)	Specification: As specified in the tender document.	Nos	100
56	01/TEND/2020/RK/472/56	Ahuja introduces a 700 Watts Professional 2 Way PA Speaker System with Exceptional LF Response, Tremendous Efficiency and Unmatched Intelligible Sound. Two 15 High Performance LF Transducers and a High Frequency Titanium Compression Horn Driver housed in an acoustically treated Bass Reflex Trapezoidal enclosure with ultra-modern paint finish.Sturdy and Aesthetically Designed Metal Grill lends both protection to the speakers as well as superb looks to the cabinet.Well designed heavy duty metal Complete As per the Specification ( Lowest Quotation rate) MDF	Specification: As specified in the tender document.	Nos	8
57	01/TEND/2020/RK/472/57	Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete.(As per Civil SR KSRB I 2, P 7) In soil (ordinary) PWD EL SR 2019 20 NO: 6.6.1 S1, S2 & S3 Terrace	Specification: As specified in the tender document.	Nos	1750
58	01/TEND/2020/RK/472/58	Digging of trench of 0.6m deep x 0.50 mtr wide refilling the trench to the required ground level and consolidating etc., complete.(As per Civil SR KSRB I 2, P 7) In soil (ordinary) PWD EL SR 2019 20 NO: 6.6.1 N1, N2 & N3 errace	Specification: As specified in the tender document.	Nos	800
59	01/TEND/2020/RK/472/59	Supply of LED pole mounting type post top lantern with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/ clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection Min 5KV along with Over voltage/Overload, short circuit/ miss wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB . LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. PWD EL SR 2019 20 NO: 12.7.2 South Garden	Specification: As specified in the tender document.	Nos	250
60	01/TEND/2020/RK/472/60	Supply of LED pole mounting type post top lantern with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/ clear glass material, delivering superior light output Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection Min 5KV along with Over ltage/Overload, short circuit/ miss wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB . LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. PWD EL SR 2019 20 NO: 12.7.2 North Garden	Specification: As specified in the tender document.	Nos	200
61	01/TEND/2020/RK/472/61	Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS 694:1990 PWD EL SR 2019 20 NO: 2.5.23 4C X 6Sq.mm	Specification: As specified in the tender document.	Nos	3600