Construction Of Conference Hall Above Bdo Office Building At Gohar District Mandi H . P Building Work
Tender Value
85.63 Lakhs
Estimated cost
Bid Submission
29 Dec 2020
0 days left
EMD
1.18 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
GOHAR DISTRICT MANDI HP → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Conference Hall Above Bdo Office Building At Gohar District Mandi H . P Building Work
BOQ
| NAME OF WORK:- CONSTRUCTION OF CONFRENCE HALL ABOVE BDO OFFICE BUILDING AT GOHAR DISTT MANDI (HIMACHAL PRADESH) | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Excavation in foundation trenches etc. in earth work in all kinds of soil such as pick work ,pick jumper work , jumper blasting work , soft and hard blasting ,saturated soil , including chiseling or any other mixed variety of soil in all leads dewatering and or removal of slush and other incidentals , including stacking the excavated soil clear from the edge of excavation and than returning the stacked soil in all thickness of layers when required into plinths side of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 10.8 | cum | |
| 2 | 2 | Demolation above ground level up to all floor level including disposal of unserviceable material with in all leads and lifts including cutting the necessary reinforcement and separating out from RCC work disposing of all surplus excavated earth including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 8.34 | cum | |
| 3 | 3 | Providing from work with steel plates 3.15 mm (three decimal fifteen millimeter ) thick welded with angle iron in frame 30X30X5 mm (thirty into thirty into five millimeters )so as to give a fair finish including centering , shuttering ,strutting and propping etc. with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling & removal of same for in-situ reinforced concrete and plain concrete work including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. in | |||
| 4 | 3.01 | Foundation ,footing basis of columns etc. And mass concrete as per direction including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 18.18 | sqm | |
| 5 | 3.02 | Flat surfaces, such as soffits of the suspended floors roofs , landing and the like floors etc. up to any thickness , all as per direction of the Engineer-in Charge including s carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . | 13.68 | sqm | |
| 6 | 3.03 | Beams cantilever girders and lintels side and soffits of beams ,beams haunchings, cantilevers ,bressumers and lintels any depth in all heights from floor as per direction of the Engineer-in Charge including carriage of material with in all leads ,lifts in all floor levels and other incidentalscomplete in all respect . | 99.82 | sqm | |
| 7 | 3.04 | Columns, pillars ,posts and struts square, rectangular or polygonal in plan as per direction of the Engineer-in Charge Inculdings carriage of material with in all leads ,lifts in all floor levels and other incidentals complete in all respect . | 140.52 | sqm | |
| 8 | 4 | Providing and laying, mechanically mixed and vibrated cement concrete 1:6:12 (one cement:Six sand Twelve graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 2.54 | cum | |
| 9 | 5 | Providing and laying M-25 grade of concrete with minimum cement contents of 400kg (four hundred kilogrames per cum )mechanically mixed and vibrated graded crushed stone aggregate 20mm nominal size and curing complete excluding the cost of form work and reinforcement for reinforced concrete work including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. in :- | |||
| 10 | 5.01 | Foundation ,footing basis of columns etc and mass concrete as per direction of the Engineer-in-charge including carriage of material with in all leads , lifts and other incidentals complete in all respect. | 4.72 | cum | |
| 11 | 5.02 | Suspended Floors , roofs , landings shelves and their supports , balconies beams ,girders, bressumers and cantilever for all floors levels , complete as per direction of the Engineer-in Charge including carriage of material with in all leads ,lifts and other incidentals complete in all respect. | 15.05 | cum | |
| 12 | 5.03 | Column , pillars , posts and structs square , rectangular or polygonal in plan as per direction of the Engineer-in Charge including carriage of material with in all leads andlifts and other incidentals' complete in all respect. | 17.44 | cum | |
| 13 | 6 | Providing tor steel reinforcement of TATA or SAIL make for reinforced Cement concrete work including bending ,binding and placing in position and cost of binding wire complete for all floors including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 5294 | kg | |
| 14 | 7 | Boulder filling under floors including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 1.78 | cum | |
| 15 | 8 | Brick work using second Class common burnt clay building bricks, in cement mortar 1:6(one cement :six sand ) in super structure upto all floor levels including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 43.28 | cum | |
| 16 | 9 | Half bricks masonry using second class common burnt clay building bricks in cement mortar 1:4 (one cement :four sand ) in super structure up to all floor levels including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 26.12 | sqm | |
| 17 | 10 | Providing and fixing 10 mm ( ten mm) thick water proof stain and impact resistent heavy duty (double charge) vetrified tiles nitco or equivalent 600x600x10 mm thick manufactured of approved shade and colour in flooring treads of steps and landing over 12 mm ( twelve milimeters) thick cement mortar 1:3 ( one cement : three sand) and jointed with cement slurry including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 376.45 | sqm | |
| 18 | 11 | Providing and fixing 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 304.05 | sqm | |
| 19 | 12 | Providing and fixing ridges or hips 60 cm over all with 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 36.05 | mtr | |
| 20 | 13 | Providing and fixing VALLEY 60 cm over all with 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 24 | mtr | |
| 21 | 14 | Providing and fixing M.S BP sheet 1.66 mm to 2 mm thick in eaves board / facia / soffit / ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of engineer in charge ( base members of steel work shall be measured and paid separtely including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 209.28 | sqm | |
| 22 | 15 | Steel work welded in built up sections, Steel hollow sections trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 117.86 | Qtl. | |
| 23 | 16 | Providing and fixing on wall face PVC (D-plast) rain water pipes of workng pressure not less than 4.50kg/sqm including filling the joints with approved adhesive complete 100 MM dia pipes including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 24 | mtr. | |
| 24 | 17 | Providing and fixing M.S holder bat clamps of approved design to C.I or S.C.I pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4:mix (one cement:two sand:four stone aggregated 20mm nominal size )and cost of cutting holes and making good the walls etc.100 mm diameter for C.I pipes including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 16 | each | |
| 25 | 18 | Providing and fixing on wall face PVC (D-plast)accessories for rain water pipes including filling the joints with approved adhesive including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | |||
| 26 | 18.01 | PVC plain bend 100mm diameter | 6 | each | |
| 27 | 18.02 | PVC plain shoes 100mm diameter | 6 | each | |
| 28 | 19 | Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead , red oxide/zinc oxide crome including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 61.47 | SQM | |
| 29 | 20 | Painting two coats (excluding priming coat )on new steel and other metal surface with enamel paint other then white brushing to give an even shade including cleaning surface of all dirt dust and other foreign matter including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 784.08 | SQM | |
| 30 | 21 | 15mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete/stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and/ or rounded angles not exceeding 80mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement :six sand )as per direction of engineer in charge including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 287.33 | SQM | |
| 31 | 22 | Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 287.33 | SQM | |
| 32 | 23 | Distempering (two coats )with oil bound washable distemper of approved brand and manufacture and required shade on un-decorated wall surfaces to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing surface free from mortar dropping and other foreign matter and also including preparing the surfaces even and sand papered smooth priming coat with distemper primer including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 287.33 | SQM | |
| 33 | 24 | Supplying ,drilling/cleaning hole -and injectning Hilti make ETA approved RE 500 V3 Chemical with the help of hilti-HDM 500 dispenser , into a hole of dia & depth as per manufacturer/structural consultants specification and fixing rebars of required diameter.The chemical should be fire and corrosion resistants . fixing methodology to be followed as per bar depth calculations based on designed load and accordance with EOTA-TR-023 guidline for the post installed rebars. including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | |||
| 34 | 24.01 | 16mm dia depth 160mm | 8 | each | |
| 35 | 24.02 | 20mm dia depth 200mm | 196 | each | |
| 36 | 24.03 | 25mm dia depth 250mm | 48 | each | |
| 37 | 25 | Providing and laying Exterior vetrified tiles of size 1200mm x 200 mm and 6mm thickof approved brand and manufactures in all colours and shades as per the approval of Engineer -in -charge on exposed surfaces of wall fixed with 8mm wide groves with cement based high polymer modified quick set tiles adhesive (water based) conferming to IS:15477 including grouting of joints including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 897.86 | sqm | |
| 38 | 26 | Providing and fixing tiled false ceiling of specified material of size 595x595 mm in true horizontal level suspended on interlocking metal grid of hot dipped galavinised steel sections (galvanised @120 gm/sqm both sides inclusive)consisting of main T runner with sutiably joints to get required length and of size 24x38 mm made from 0.30mm thick (minimum)sheet spaced at 1200mm center to center and cross T of size 24mmx 25mm made of 0.30mm thick (minimum) sheet 1200mm long spaced between main T @600mm center to center to form a grid of 1200 x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30mm thick minimum sheet to be inter locked at middle of the 1200x600 mm panel to form grids of 600mm x600mm and wall angle of size 24x24x 0.3mm and laying false ceiling tiles of approved texture in the grid including ,required ,cutting/making,opening for services like diffusers grills,light fittings ,fixturers ,smoke,detectors etc.Main T runners to be suspended from ceiling using G I slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners ,4mm GI adjustable rod with galvanised butterfly level clips of size 85x30x0.8mm spaced at 1200mm center to center along main T,bottom exposed width of 24mm of all T sections shell be prepainted with polyester paint all complete for all heights as per specifications,drawings including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | |||
| 39 | 26.01 | 12.5mm thick square edge PVC Laminated ,Gypsum tile of size 595x595mm made of Gypsum plaster board manufactured from natural Gypsum as per IS 2095 part -I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12 microne metalized polyster on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.. | 475.36 | sqm | |
| 40 | 27 | Providing and fixing wall Panelling made out of base frame of aluminium tubler section 25mm x50mm x1.5mm thick placed @ 600mm center to center on both ways finished with 12mm thick water proof ply . The back of water proof ply shall be finished with 3mm thick PVC sheet with adhesive to avoid the moisture. The top surface of the ply shall be finished with 12mm thick first class deodar wood planks as per required design and pattern including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 472.34 | sqm | |
| 41 | 28 | Providing and fixing aluminium work for doors,windows,ventilators and partitions with extruded built up standard tubular sections / appropirate Z sections and other sections of approved make conferming to IS 733 and IS 1285 fixing with - fastener of required dia and size including necessary filling up the gaps and junctions i.e at top bottom and sides with EPDM rubber /neoperene Gasket etc .Aluminium section shall be smooth rust free straight mitred and jointed mechanically where ever required including cleat angle aluminium snape biddinf for glazing / panelling CP brass /stainless steel screw all complete as per drawings and directions of Engineer in charge(Glazing,paneling and dash fasteners to be paid for separately) including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | |||
| 42 | 28.01 | For fixed portion. Powder coated aluminium(minium thickness of powder coating 50 micron | 455.3 | kg | |
| 43 | 28.02 | For shutters of doors windows and ventilators including providing and fixing hinges /Pivots and making provision for fixing of fittings where ever required including the cost of EPDM rubber/ neoprene gasket required. Powder coated aluminium(minium thickness of powder coating 50 micron | 319.14 | kg | |
| 44 | 29 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layers or graded wood partical board conforming to IS:12823 grade I type II in panelling fixed in aluminium doors windows shutters and partitions frames with CP brass / stainless steel screws etc. complete as per drawings and directions including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 9.45 | sqm | |
| 45 | 30 | Providing and fixing glazing in Aluminium doors windows ventilators shutters and partitions etc with EPDM rubber/ neoprene gasket etc complete as per drawings and directions including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 61.47 | sqm | |
| 46 | 31 | Providing and fixing Aluminium tabular handlebar 32mm dia 3.00 mm thick and 2100 mm long SS screws etc complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 72 | each | |
| 47 | 32 | Providing and fixing brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality )for aluminium doors including necessary cutting and making the good etc complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 5 | each | |
| 48 | 33 | Providing and fixing bright finished brass tower bolts ISI marked barrel type with the screws etc complete as per direction of the engineer in charge including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | |||
| 49 | 33.01 | 200mmX10 mm (Two hundred millimeters Into ten millimeters) | 20 | each | |
| 50 | 33.02 | 150mmX10 mm (One hundred fiftymillimeters Into ten millimeter) | 104 | each | |
| 51 | 34 | Providing and fixing 200mm weighing not less then 240gms chromium plated brass casement stay with necessary screws complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 26 | each | |
| 52 | 35 | Providing and fixing 100mm bright finished brass floor Door stopers with rubber cushion screws etc to suit shutter thickness complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 5 | each | |
| 53 | 36 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15 )of approved design and pattern with approved standred sections and fixed to the existing windiw frame with CP brass /SS screws @ 200mm center to center including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standerd section arround the opening all complete including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 461.02 | kg | |
| 54 | 37 | Providing and fixing Stainless steel (grade 304 railing made of hollow tubes channels plates etc including grinding buffing polishing and making curvature where ever required and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fastner stainless steel boards etc of required size on the top of floor or the inside of waist size slab with suitable arrangement as per approval of Engineer in charge ) for payment purpose only stainless steel members shall be considered excluding fixing accessories such as nuts bolts fastners etc. including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 57.78 | kg | |
| 55 | 38 | Providing and placing on terrace(at all floor levels)polyethylene water storage tank ,IS:12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and the base support for tank including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 4000 | litr. | |
| 56 | 39 | Providing and fixing fly proof stainless steel grade 304 wire gauge ,to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia 0.50 mm all complete wit 12 mm aluminium U beading including carriage as required complete in all respect in all leads & lift in all floor levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. | 23.49 | SQM |
AI Tender Summary
Tender Timeline
Dec 14, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedDec 29, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 30, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender