Supply, Installation & Commissioning Of Led Light Fitting -Karnataka

Supply, Installation & Commissioning Of Led Light Fitting 1. Supplying And Fixing Angle Iron Frame Work Fabricated Out Of M.S. Angle Iron. And M.S. Flat With Bolts, Washers Etc., And Painted With 2 Coats Of Red Oxide And Then Two Coats Of Approved Paint. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.41.2) 50X50x6mm, 2. Supplying And Fixing Microprocessor Based Electronic Timer (Without Contactor,Din Mounting Using Necessary Bolts, Nuts And Washers Etc.) As Per The Direction Of Work Incharge Engineer 3 120Sec. ( Pwd Electrical Sr 2019 20 Page No 32, Item No 5.47), 3. Supply And Fixing Of 4Pole Power Contactor With No/Nc Contacts On Existing Wood/Panel Board Using Necessary Bolts, Nuts, Washers And Wiring Etc., Complete With Ac 3 Rating And As Per Is 13947. As Per The Direction Of Work Incharge Engineer( ( Pwd Electrical Sr 2019 20 Page No 26, Item No 5.13.1) A) 25Amps, 4. Supplying And Fixing Moulded Case Circuit Breaker (Mccb) Over The Existing Wood/Panel Board Using Necessary Screws, Bolts, Nuts And Wiring Complete. Protection Of Overload And Short Circuit With Thermal Magnetic/Microprocessed Release And Earth Fault As Per Is13947. ( Icu = Ics) (Pwd Electrical Sr 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25Ka., 5. Ksrb 22 : Earthwork Excavation By Manual Means For Foundation Of Buildings, Water Supply And Sanitary Lines And Electrical Conduits Etc, Either In Pits Or In Trenches 1.5M And Above In Width, In Soil Not Exceeding 1.5 M. In Depth Including Dressing The Bottom And Sides Of Pits And Trenches, Stacking The Excavated Soil Clear From Edges Of Excavation With Lead Upto 50 M. Including Breaking Of Clods Complete As Per Specifications In Ordinary Soil..(Pwd Civil Sr 2018 19, Pg.No.6, It.No.2.3) For Panel, 6. Ksrb 2 2 : Earthwork Excavation By Manual Means For Foundation Of Buildings, Water Supply And Sanitary Lines And Electrical Conduits Etc, Either In Pits Or In Trenches 1.5M And Above In Width, In Soil Not Exceeding 1.5 M. In Depth Including Dressing The Bottom And Sides Of Pits And Trenches, Stacking The Excavated Soil Clear From Edges Of Excavation With Lead Upto 50 M. Including Breaking Of Clods Complete As Per Specifications In Ordinary Soil..(Pwd Civil Sr 2018 19, Pg.No.6, It.No.2.3) For Street Light Pole, 7. Ksrb 4 1.3 : Providing And Laying In Position Plain Cement Concrete Of Mix 1:4:8 With Opc @ 180Kgs, With 40Mm And Down Size Graded Granite Metal Coarse Aggregates @0.85Cum And Fine Aggregates @0.57Cum Machine Mixed, Machine Mixed, Concrete Laid In Layers Notexceeding 15 Cms. Thick, Well Compacted, In Foundation, Including Costof All Materials, Labour, Hom Curing Complete As Per Specifications. Specification No. Kbs 4.1, 4.2 (Pwd Civil Sr 2018 19 P.No13, It.No. 4.3) For Street Light Pole, 8. Ksrb 4.2.2 : Providing And Laying In Position Reinforced Cement Concrete Of Design Mix M20 With Opc @ 320Kgs, With 20Mm And Down Size Graded Granite Metal Coarse Aggregates @0.69Cum And Fine Aggregtes @ 0.460 Cum, With Super Plasticisers @ 3 Liters Confirming To Is 9103-1999 Reafirmed 2008, Machine Mixed, Concrete Laid In Layers Not Exceeding 15 Cms Thick, Vibrated For All Works In Foundation For Footings, Pedastals, Retaining Walls, Return Walls, Walls (Any Thickness) Including Attached Pilasters, Columnspillars, Posts, Struts, Buttresses, Bed Blocks, Anchor Blocks & Plinths Etc., Including Cost Of All Materials, Labour, Hom Curing, Complete But Excluding Cost Of Reinforcement As Per Specifications.Specification No. Kbs 4.1, 4.6 (Pwd Civil Sr 2018 19, Pg.No.13, It.No.4.11) For Panel, 9. Ksrb 4.2.2 : Providing And Laying In Position Reinforced Cement Concrete Of Design Mix M20 With Opc @ 320Kgs, With 20Mm And Down Size Graded Granite Metal Coarse Aggregates @0.69Cum And Fine Aggregtes @ 0.460 Cum, With Super Plasticisers @ 3 Liters Confirming To Is 9103 1999 Reafirmed 2008, Machine Mixed, Concrete Laid In Layers Not Exceeding 15 Cms Thick, Vibrated For All Works In Foundation For Footings, Pedastals, Retaining Walls, Return Walls, Walls (Any Thickness) Including Attached Pilasters, Columns Pillars, Posts, Struts, Buttresses, Bed Blocks, Anchor Blocks & Plinths Etc., Including Cost Of All Materials, Labour, Hom Curing, Complete But Excluding Cost Of Reinforcement As Per Specifications. Specification No. Kbs 4.1, 4.6 (Pwd Civil Sr 2018 19, Pg.No.13, It.No.4.11 For Street Light Pole, 10. Ksrb 4.9.2 : Providing T.M.T Steel Reinforcement For R.C.C Work Including Straightening, Cutting, Bending, Hooking, Placing In Position, Lapping And / Or Welding Wherever Required, Tying With Binding Wire And Anchoring To The Adjoining Members Wherever Necessary Complete As Per Design (Laps, Hooks And Wastage Shall Not Be Measured And Paid) Cost Of Materials, Labour, Hom Complete As Per Specifications. Specification No. Kbs 4.6.3 Tmt Bars Fe 500(Pwd Civil Sr 2018 19 P.No18, It.No. 4.46.2) Steel For Street Light Pole, 11. Supply And Installation / Fixing / Provision Of Pole Box With Hrc Fuse / Mcb Provision And Suitable Connector / Terminal For 3 Ph / 1 Ph Connections With Loop In & Loop Out Terminals For 10 Sqmm / 25 Sqmm 3.5 C Al/Ar / Cu/Ar Cable And Branch Out 2.5 Sqmm 2 Core Al/Cu Pvc Insulated Cable, Enclosed In A Thermoplastic, Polystyrene Enclosure, Which Should Be Shock Proof, Safe, Ip65(Weather Proof), Rust Proof, Dust Proof, Water Proof Having Internally Embedded Gasket With Provision For Cable Entry Through Ip65 Thermoplastic, Polyamide Glands And/Or Grommets.200X200x98mm(Pwd Electrical Sr 2019 20 Page No 31 Item No 5.43.1), 12. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 6 32Amps Sp, 13. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 63 Amps Sp, 14. Supplying & Fixing Of Porcelain Fuse Channel With Cut Out On Existing Wooden/Panel Using Necessary Nuts, Bolts And Washers(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.7.2) 32 Amps, 15. Supplying & Fixing Of Porcelain Fuse Channel With Cut Out On Existing Wooden/Panel Using Necessary Nuts, Bolts And Washers(Pwd Electrical Sr 2019 20, Pgno.25, It.No.5.7.2) 63 Amps, 16. Supplying, Fixing, Wiring, Earth Electrode For Grounding Conduits, I.C. Cutouts And Other Equipments On The Meter Board Using 40Mm Dia 2.90Mm Thick Gi Pipe 2.5 Mtr Long Buried In A Pit The Pit Should Be Filled With Equal Proprotion Of Salt And Charcoal 150Mm Alround The Pipe To Complete Depth. The Connection From The Pipe To The Conduit Etc, Is To Be Established Through Gi Wire Of Size As Per Isi Specification 7.3.3. Of Is 732 Using 12Mm Dia Bolts, Nuts, Washers And Checknuts Etc, The Pipe Shall Have 16 Through Holes Of 122 Mm Dia ( 55 / 7.1) (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.1), 17. Supplying Pvc/Gi Flexible Conduit Pipe50mm Fixing On Surface Over Inverted Tapered Wooden Plugs Or Phill Plugs Or Rawl Plugs And Clamped Using Heavy Gauge Saddles At An Interval Of 300Mm Using Nf Screws And On Either End Of The Pipe Terminated Completely(Pwd Electrical Sr 2019 20, Pgno.3, It.No.1.9.5 ), 18. Painting Of Existing Street Light Pole After Scrapping The Old Paint And Painted With Suitable Colour Enamel/Silver Paint Including Coping/Footing Of The Pole.(Pwd Electrical Sr 2019 20, Pgno.72, It.No.13.17.3) 8Mtr And Above Street Light Pole., 19. Supplying And Fixing Of........Mm Dia Class A Gi Pipe Bracket Up To 2 Mtrs Long Bent At Suitable Angle And Fixing To This Bracket 1X40/2X40 Watts Fluorescent Tube Street Light Fitting Of All Capacities To Gi Or Ci Or Rail Or Rcc Pole / Wall Using Suitable Clamps, Bolts, And Nuts And Wiring Using Suitable Capacity Wires. (Pwd Electrical Sr 2019 20, Pgno.79, It.No.14.1.2) Using 32Mm Dia G.I.Pipe, 20. Supplying And Fixing Telescopic M.S. Bracket Fabricated By Using 0.5M Length 4 Dia Telescopic M. S. Pipe, With 2 Dia 1.5M Long M. S. Bracket And Are Welded With Suitable Angle, Using 6Mm Thick M. S. Sheet, Grip Bolts & Nuts, As Required, Suitable For 9 To 12 Mtrs. M. S. Tubular Pole, With Necessary Two Coats Of Painting, With All Other Accessories(Pwd Electrical Sr 2019 20, Pgno.79, It.No.14.4.2) Single Bracket 2 Mtr. Length, 21. Supplying And Fixing Telescopic M.S. Bracket Fabricated By Using 0.5M Length 4 Dia Telescopic M. S. Pipe, With 2 Dia 1.5M Long M. S. Bracket And Are Welded With Suitable Angle, Using 6Mm Thick M. S. Sheet, Grip Bolts & Nuts, As Required, Suitable For 9 To 12 Mtrs. M. S. Tubular Pole, With Necessary Two Coats Of Painting, With All Other Accessories(Pwd Electrical Sr 2019 20, Pgno.79, It.No.14.4.2) Single Bracket 2 Mtr. Length, 22. Supplying And Drawing Flexible Multicore Cable Manufactured With Electrolytic Grade Flexible Copper With Low Conductor Confirming To Is:8130 1984 And (Virgin) Pvc Insulation Sheathed Suitable For Working Voltage Upto 1100Volts As Per Is 694:1990(Pwd Electrical Sr 2019 20, Pgno.6, It.No.2.5.7) 2C X 2.5Sq.Mm, 23. Supplying And Erection Of 3 Phase, 11Kv/433 V, 100Kva Bee 4/5 Star Rated Distribution Transformer Centre Using Dpts And All Accessories ( Bescom Sr 201617 Cds26) Mr+Lr, 24. Fabricating, Supplying And Erection Of Rs Long Hot Dip Galvanized Conical Pole With Bsen 10025 Grade S355jo Steel Plate For Shaft, Is 2062 For Base Plate With Door Opening Arrangements, Including Suitable Boards, Bakelite Sheet And Mcbs As Per Is Specifications Suitable To Withstand The Wind Speed Of 47 M/Sec For Mtrs Pole In Single Section And Single Joint Welded As Per Is 9595/Is 10178Aws Having Dimensions Bottom Mm, Topmm With 3Mm Thick, Suitable Base Plate And 4Nos Of Long J Bolts Along With Template And The Pole Shall Be Hot Dip Galvanized In Single Dipping With Not Less Than 65Micron As Per Astm A123 And 153 Etc.,(Excluding Foundation) As Per Drawing Appended.(Pwd Electrical Sr 2019 20, Pgno.14, It.No.4.4.8) 10 Meters Top 75Mm And Bottom 165 Mm Dia, 25. Supplying Of 1.1 Kv Lt Ug Cable Having Aluminium Conductor Pvc Insulated, Extruded Inner Sheathed, Galvanised, Steel Strip (Except 2Cx10sq.Mm Wire Armoured) Confirming To Is 3975:1990 (No. Of Strip Indicated In Gtp) & Extruded Pvc Outer Sheathed Armoured Cable With Specified Is 1554 Part 1:1988 & Confirming To The Attached Gtp Of Group A. As Per The Direction Of Work Incharge Engineer 3.5 Core 35 Sqmm (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.4.6), 26. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refiling The Trench To The Required Ground Level And Consolidating Etc., Complete. As Per The Direction Of Work Incharge Engineer In Soil (Ordinary)(Pwd Electrical Sr 2019 20 Page No 41, Item No 6.6.1), 27. Digging Of Trench Of 0.6M Deep X 0.50 Mtr Wide Refiling The Trench To The Required Ground Level And Consolidating Etc., Complete. As Per The Direction Of Work Incharge Engineer In Soil (Hard)(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.6.2), 28. Labour Charges For Laying Of 1.1 Kv Class Ug Cable In Existing Trench Gi Pipe / Stoneware Pipe / On Wall / On Pole As Required. As Per The Direction Of Work Incharge Engineer 25 Sqmm To 75 Sqmm (Pwd Electrical Sr 2019 20 Page No 41, Item No 6.5.2), 29. Supplying And Fiixing Of Heavy Duty Cable Glands Suitable For Ug Cable Of 1.1 Kv Class (Metal Only)45Mm Dia(Pwd Electrical Sr 2019 20 Page No 42, Item No 6.11.4), 30. Supplying And Running Gi/Copper Conductor For Grounding And (Along With Other Wires In Conduit System Of Wiring) Using Necessary Suitable Size Clamps, Nails, Guttas/Spacers Etc..( 64 / 7.22)(Pwd Electrical Sr 2019 20 Page No 44, Item No 6.18.6) Copper Wire 8 Swg, 31. Supplying Tinned Copper Lugs And Crimping And Wiring To Terminal Point For Wire Of The Following Sizes.F) 35 Sqmm Long Barrel(Pwd Electrical Sr 2019 20 Page No 43, Item No 6.17.8, 32. Fabricating Supplying And Mounting Ms Box Made Out Swg Suitable For Floor / Wall Mounting, Fully Weather Proof With Provision For Better Heat Dissipation, Provided With Hinged Front Cover, Equipped With Tamper Proof Locking Arrangements, With Suitable Size Clamps With Necessary Cable Entry Pipe With Gland And Box Should Be Finished With 2 Coats Of Red Oxide Primer Paint And Finally Finished With Approved Colour Enameled Metal Paint Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.42.1) 14Swg, 33. Supplying Amps Rated 3Phase With Neutral Bus Bar Using Required Capacity Electrolytic Alluminium Strips Covered With Heat Shrinkable Coloured Pvc Sleeve, Mounted On Phenolic/Frp/Dmc Insulator Which Are Mounted On Powder Coated 40X6mm M.S.Flat Frame Work In Existing Panel Board. The Bus Bar Shall Have Suitable Holes For Termination Of Incoming And Outgoing Cables As Per Is Specification With Necessary Botls,Nuts And Washers Etc., Complete. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.40.1) 100Amps 4X30x6mm Alluminium Strips, 34. Supplying And Fixing Angle Iron Frame Work Fabricated Out Of M.S. Angle Iron. And M.S. Flat With Bolts, Washers Etc., And Painted With 2 Coats Of Red Oxide And Then Two Coats Of Approved Paint. (Pwd Electrical Sr 2019 20 Page No 30, Item No 5.41.2) 50X50x6mm, 35. Supplying And Fixing Microprocessor Based Electronic Timer (Without Contactor, Din Mounting Using Necessary Bolts, Nuts And Washers Etc.,.) As Per The Direction Of Work Incharge Engineer 3 120Sec. ( Pwd Electrical Sr 2019 20 Page No 32, Item No 5.47), 36. Supply And Fixing Of 4Pole Power Contactor With No/Nc Contacts On Existing Wood/Panel Board Using Necessary Bolts, Nuts, Washers And Wiring Etc., Complete With Ac 3 Rating And As Per Is 13947. As Per The Direction Of Work Incharge Engineer( ( Pwd Electrical Sr 2019 20 Page No 26, Item No 5.13.1) A) 25Amps, 37. Supplying And Fixing Moulded Case Circuit Breaker (Mccb) Over The Existing Wood/Panel Board Using Necessary Screws, Bolts, Nuts And Wiring Complete. Protection Of Overload And Short Circuit With Thermal Magnetic/Microprocessed Release And Earth Fault As Per Is 13947. ( Icu = Ics) (Pwd Electrical Sr 201920 Page No 26, Item No 5.14.1) Four Pole,100Amps 25Ka., 38. Ksrb 2 2 : Earthwork Excavation By Manual Means For Foundation Of Buildings, Water Supply And Sanitary Lines And Electrical Conduits Etc, Either In Pits Or In Trenches 1.5M And Above In Width, In Soil Not Exceeding 1.5 M. In Depth Including Dressing The Bottom And Sides Of Pits And Trenches, Stacking The Excavated Soil Clear From Edges Of Excavation With Lead Upto 50 M. Including Breaking Of Clods Complete As Per Specifications In Ordinary Soil..(Pwd Civil Sr 2018 19, Pg.No.6, It.No.2.3) For High Mast, 39. Supplying And Fixing Of Modular Mcb Devices( Tripper) With Breaking Capacity Of 6Ka.. (Pwd Electrical Sr 2019 20, Pgno.31, It.No.5.46.1 &5.46.3) 63 Amps Sp, 40. Supplying, Fixing, Wiring, Earth Electrode For Grounding Conduits, I.C. Cutouts And Other Equipments On The Meter Board Using 40Mm Dia 2.90Mm Thick Gi Pipe 2.5 Mtr Long Buried In A Pit The Pit Should Be Filled With Equal Proprotion Of Salt And Charcoal 150Mm Alround The Pipe To Complete Depth. The Connection From The Pipe To The Conduit Etc, Is To Be Established Through Gi Wire Of Size As Per Isi Specification 7.3.3. Of Is 732 Using 12Mm Dia Bolts, Nuts, Washers And Checknuts Etc, The Pipe Shall Have 16 Through Holes Of 122 Mm Dia ( 55 / 7.1) (Pwd Electrical Sr 2019 20 Page No 40, Item No 6.1), 41. Supplying Pvc/Gi Flexible Conduit Pipe50mm Fixing On Surface Over Inverted Tapered Wooden Plugs Or Phill Plugs Or Rawl Plugs And Clamped Using Heavy Gauge Saddles At An Interval Of 300Mm Using Nf Screws And On Either End Of The Pipe Terminated Completely(Pwd Electrical Sr 2019 20, Pgno.3, It.No.1.9.5 ), 42. Supplying And Drawing Flexible Multicore Cable Manufactured With Electrolytic Grade Flexible Copper With Low Conductor Confirming To Is:8130 1984 And (Virgin) Pvc Insulation Sheathed Suitable For Working Voltage Upto 1100Volts As Per Is 694:1990(Pwd Electrical Sr 2019 20, Pgno.6, It.No.2.5.7) 8C X 2.5Sq.Mm, 43. Fabrication, Supplying, Erection, Testing And Commissioning Of Mtrs Long Polygon High Mast With Single / Multiple Telescopic Sections Having, (Minimum Overlap Distance Of 1.5 Times Of Top Section) Thickness As Per Bsen 10025 Grade S 355 Jo /Astm A572 50 Steel Sheet Plate For Shaft Suitable To Withstand A Wind Velocity Of 47 M/Sec As Per Is 875 Part 3(As Per Ga Drawing).Base Plate As Per Is 2062/Astm A572 50. The Mast Shall Be Galvanized In Single Hot-Dip As Per Bsen Iso 1461/Astm A123 With An Average 70 Microns As Per Is 2629, And Welded As Per Bs 5135 Single L Seam Joint. The Mast Shall Have 2Way Head Frame With Die Cast Lm 6 Pulleys, Stainless Steel Axle, Phosphorus Bronze Bearing Bush Press Fitted With Separate Guides For 2 Runs Of 5Mm Dia, Stainless Steel Wire Rope Of Aisi 304Grade 7/19Core, (Factor Of Safety As Per Tr No 7). 2.5Sqmm Epr Insulated Pcp Sheathed Trailing Power Cable Housed Inside The Bottom Shaft Of Mast With Door Having Locking Arrangement. The Mast Shall Have Manual / Power Tool (Suitable Reversible Geared Motor Operating On 230/ 415V, 50Hz, Shall Be Provide Above 15 Mtrs Mast) The Mast Shall Have Lantern Of 2 Segments, Suitable Dia With Max Load Carrying Capacity As Per Is 1239. The Mast Shall Be Erected On Existing Rcc Footing. The Mast Shall Be Supplied With 3Mm Thick Template, Lightning Arrester Of 1.2M Length Galvanized Pipe With Top Arrow Fitted On Top Of The Head Frame Cover And Gls Type Aviation Twin Lamps Fitting With Wiring Complete. (Excluding Foundation) As Per Technical Data.(Pwd Elecrical Sr 2019 20 P.No 15 It.No.4.5.2) 16Mtrs Top 150Mm And Bottom 410 Mm Dia, 44. Supplying, And Fixing Of Hot Dip Galvanized M.S.Bracket Suitable For Out Door Luminaries And Mounted On Octagonal Pole Using Necessary Bolts, Nuts Etc., Complete(Pwd Electrical Sr 2019 20, Pgno.16, It.No.4.7.5) Double Arm Bracket With 1500Mm Standard 40/50Mm Dia, 45. Supplying And Fixing Electronic Trivector Meter (Etv) Suitable For Operation Lt Operation And Ct Operated Meter In Polycarbonate Body In Class 0.5 Accuracy As Per Is 14697 And Completely Wired (Pwd Electrical Sr 2019 20, Pgno.29, It.No.5.31), 46. Supplying And Fixing Of Class A (Medium Duty) Gi Pipe Of Wall Thickness Not Less Than 3.25Mm On Pole/Wall/Drain Crossing With Necessary Clamping Arrangements For Ug Cable Of 1.1 Kv. 65Mm (Pwd Electrical Sr 2019 20, Pgno.42, It.No.6.9.3), 47. Providing And Laying In Position 100Mm Dia Stone Ware Pipe In Existing Trench. (Pwd Electrical Sr 2019 20, Pgno.41, It.No.6.8), 48. Ksrb 4 1.3 : Providing And Laying In Position Plain Cement Concreteof Mix 1:4:8 With Opc @ 180Kgs, With 40Mm And Down Size Gradedgranite Metal Coarse Aggregates @0.85Cum And Fine Aggregates @0.57Cum Machine Mixed, Machine Mixed, Concrete Laid In Layers Notexceeding 15 Cms. Thick, Well Compacted, In Foundation, Including Costof All Materials, Labour, Hom Curing Complete As Per Specifications. Specification No. Kbs 4.1, 4.2 (Pwd Civil Sr 2018 19 P.No13, It.No. 4.3), 49. Ksrb 4 1.6 ; Providing And Laying In Position Plain Cement Concrete Of Mix 1:2:4 With Opc @ 240Kgs, With 20Mm And Down Size Graded Granite Metal Coarse Aggregates @ 0.878 Cum And Fine Aggregtes @ 0.53Cum, Machine Mixed, Concrete Laid In Layers Not Exceeding 15 Cms. Thick, Well Compacted, In Foundation, Plinth And Cills, Including Cost Of All Materials, Labour, Hom Curing Complete As Per Specifications. Specification No. Kbs 4.1, 4.2(Pwd Civil Sr 2018 19 P.No13, It.No. 4.6), 50. Ksrb 4.9.2 : Providing T.M.T Steel Reinforcement For R.C.C Work Including Straightening, Cutting, Bending, Hooking, Placing In Position, Lapping And / Or Welding Wherever Required, Tying With Binding Wire And Anchoring To The Adjoining Members Wherever Necessary Complete As Per Design (Laps, Hooks And Wastage Shall Not Be Measured And Paid) Cost Of Materials, Labour, Hom Complete As Per Specifications. Specification No. Kbs 4.6.3 Tmt Bars Fe 500(Pwd Civil Sr 2018 19 P.No18, It.No. 4.46.2), 51. Supply Of Led Floodlight Luminaire With Pressure Die Cast Aluminium Housing Body For Optimal Thermal Dissipation. Lamp Compartment Comprising Of Anti Glare Clear Diffuser With Injection Moulded Polycarbonate/Clear Glass Material, Delivering Superior Light Output. Rated Life Burning Hrs 50000 Hr @ Lumen Maintenance Of 70%, Cct > 5500K, Ip 66 Optical And Electrical Compartment & Impact Resistance Of Complete Luminaire > Ik08. Power Factor >0.9 With Mains, Surge Protection- Min 5Kv Along With Over Voltage/ Overload, Short Circuit/ Miss Wiring Protection. Compatible For Pole Mouting With Outer Dia Of 40Mm To 50Mm.Universal Voltage Driver To Operate Wide Voltage Range From 100V To 270V 50/60Hz Application. Compliance To Is 10322/ Iec 60598, Lm 79 & Lm 80 Adherence With Rohs. Ul Approved Mcpcb. Top Access Street Light With Single Screw To Ensure Ease Of Maintenance At The Sight Site Location With Minimized Minimal Tools. Led Light Fixture With W System Power Consumption. Led Efficiency>130Lm/W, Nominal Cri >75. Luminaire Manufacturer Should Have Inhouse Facility Accredited By Nabl/Cpri & Any Government Certified Agency & Design & Development Facility Certified By Iso 9001:2008 . Housing With Supplier Word Mark /Name Shall Be Engraved / Embossing On The Die Cast Housing/ Body Part. Warranty Of 2 Years Against Any Manufacturing Defect Working Under Standard Electrical Conditions As Mentioned Above Should Be Given By Led Manufacturer & Cree/Nichia/ Lumileds/Osram Make Led Source. (Pwd Electrical Sr 2019 20 P.No 67 It.No 12.9.4) Led Floodlight 150W,

INR 550 /-

INR 100000.0 /-

Refer document

Sl No	Item Code	Item Name	Item Description	Unit	Quantity
1	01/TEND/2020/RK/470/01	Supplying and fixing angle iron frame work fabricated out of M.S. angle iron. and M.S. flat with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. (PWD Electrical SR 2019 20 Page No 30, Item No 5.41.2) 50X50X6mm	Specification: As specified in the tender document.	Nos	40
2	01/TEND/2020/RK/470/02	Supplying and fixing Microprocessor based Electronic timer (without contactor,Din Mounting using necessary bolts, nuts and washers etc.) as per the direction of work incharge engineer 3 120sec. ( PWD Electrical SR 2019 20 Page No 32, Item No 5.47)	Specification: As specified in the tender document.	Nos	15
3	01/TEND/2020/RK/470/03	Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC 3 Rating and as per IS 13947. as per the direction of work incharge engineer( ( PWD Electrical SR 2019 20 Page No 26, Item No 5.13.1) a) 25Amps	Specification: As specified in the tender document.	Nos	20
4	01/TEND/2020/RK/470/04	Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Microprocessed release and Earth Fault as per IS13947. ( Icu = Ics) (PWD Electrical SR 2019 20 Page No 26, Item No 5.14.1) Four Pole,100Amps 25kA.	Specification: As specified in the tender document.	Nos	30
5	01/TEND/2020/RK/470/05	KSRB 22 : Earthwork excavation by manual means for foundation of buildings, water supply and sanitary lines and electrical conduits etc, either in pits or in trenches 1.5m and above in width, in soil not exceeding 1.5 m. in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m. including breaking of clods complete as per specifications in ordinary soil..(PWD Civil SR 2018 19, Pg.No.6, It.No.2.3) For panel	Specification: As specified in the tender document.	Nos	16
6	01/TEND/2020/RK/470/06	KSRB 2 2 : Earthwork excavation by manual means for foundation of buildings, water supply and sanitary lines and electrical conduits etc, either in pits or in trenches 1.5m and above in width, in soil not exceeding 1.5 m. in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m. including breaking of clods complete as per specifications in ordinary soil..(PWD Civil SR 2018 19, Pg.No.6, It.No.2.3) For Street Light Pole	Specification: As specified in the tender document.	Nos	116
7	01/TEND/2020/RK/470/07	KSRB 4 1.3 : Providing and laying in position plain cement concrete of Mix 1:4:8 with OPC @ 180kgs, with 40mm and down size graded granite metal coarse aggregates @0.85cum and fine aggregates @0.57cum machine mixed, machine mixed, concrete laid in layers notexceeding 15 cms. thick, well compacted, in foundation, including costof all materials, labour, HOM curing complete as per specifications. Specification No. KBS 4.1, 4.2 (PWD Civil SR 2018 19 P.NO13, It.No. 4.3) For Street Light Pole	Specification: As specified in the tender document.	Nos	10
8	01/TEND/2020/RK/470/08	KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of Design Mix M20 with OPC @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to IS 9103-1999 reafirmed 2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columnspillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM curing, complete but excluding cost of reinforcement as per specifications.Specification No. KBS 4.1, 4.6 (PWD Civil SR 2018 19, Pg.No.13, It.No.4.11) For panel	Specification: As specified in the tender document.	Nos	25
9	01/TEND/2020/RK/470/09	KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of Design Mix M20 with OPC @ 320kgs, with 20mm and down size graded granite metal coarse aggregates @0.69cum and fine aggregtes @ 0.460 cum, with super plasticisers @ 3 liters confirming to IS 9103 1999 reafirmed 2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation for footings, pedastals, retaining walls, return walls, walls (any thickness) including attached pilasters, columns pillars, posts, struts, buttresses, bed blocks, anchor blocks & plinths etc., including cost of all materials, labour, HOM curing, complete but excluding cost of reinforcement as per specifications. Specification No. KBS 4.1, 4.6 (PWD Civil SR 2018 19, Pg.No.13, It.No.4.11 For Street Light Pole	Specification: As specified in the tender document.	Nos	125
10	01/TEND/2020/RK/470/10	KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM complete as per specifications. Specification No. KBS 4.6.3 TMT bars Fe 500(PWD Civil SR 2018 19 P.NO18, It.No. 4.46.2) Steel for Street light pole	Specification: As specified in the tender document.	Nos	3.37
11	01/TEND/2020/RK/470/11	Supply and Installation / Fixing / Provision of Pole box with HRC Fuse / MCB provision and suitable connector / terminal for 3 Ph / 1 Ph connections with Loop In & Loop Out terminals for 10 Sqmm / 25 Sqmm 3.5 C Al/Ar / Cu/Ar Cable and branch out 2.5 Sqmm 2 core Al/Cu PVC Insulated cable, enclosed in a Thermoplastic, Polystyrene enclosure, which should be shock proof, safe, IP65(Weather Proof), rust proof, dust proof, water proof having Internally Embedded Gasket with provision for cable entry through IP65 Thermoplastic, polyamide glands and/or grommets.200x200x98mm(PWD Electrical SR 2019 20 Page No 31 Item No 5.43.1)	Specification: As specified in the tender document.	Nos	400
12	01/TEND/2020/RK/470/12	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 6 32Amps SP	Specification: As specified in the tender document.	Nos	200
13	01/TEND/2020/RK/470/13	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 63 Amps SP	Specification: As specified in the tender document.	Nos	20
14	01/TEND/2020/RK/470/14	Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers(PWD Electrical SR 2019 20, PgNo.25, It.No.5.7.2) 32 Amps	Specification: As specified in the tender document.	Nos	16
15	01/TEND/2020/RK/470/15	Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers(PWD Electrical SR 2019 20, PgNo.25, It.No.5.7.2) 63 Amps	Specification: As specified in the tender document.	Nos	25
16	01/TEND/2020/RK/470/16	Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia ( 55 / 7.1) (PWD Electrical SR 2019 20 Page No 40, Item No 6.1)	Specification: As specified in the tender document.	Nos	20
17	01/TEND/2020/RK/470/17	Supplying PVC/GI flexible conduit pipe50mm fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely(PWD Electrical SR 2019 20, PgNo.3, It.No.1.9.5 )	Specification: As specified in the tender document.	Nos	2500
18	01/TEND/2020/RK/470/18	Painting of existing street light pole after scrapping the old paint and painted with suitable colour enamel/Silver paint including coping/footing of the pole.(PWD Electrical SR 2019 20, PgNo.72, It.No.13.17.3) 8Mtr and above street light pole.	Specification: As specified in the tender document.	Nos	50
19	01/TEND/2020/RK/470/19	Supplying and Fixing of........mm dia class A GI pipe bracket up to 2 Mtrs long bent at suitable angle and fixing to this bracket 1x40/2x40 watts fluorescent tube street light fitting of all capacities to GI or CI or rail or RCC pole / wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires. (PWD Electrical SR 2019 20, PgNo.79, It.No.14.1.2) Using 32mm dia G.I.Pipe	Specification: As specified in the tender document.	Nos	50
20	01/TEND/2020/RK/470/20	Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4 dia telescopic M. S. pipe, with 2 dia 1.5m long M. S. bracket and are welded with suitable angle, using 6mm thick M. S. sheet, grip bolts & nuts, as required, suitable for 9 to 12 Mtrs. M. S. tubular pole, with necessary two coats of painting, with all other accessories(PWD Electrical SR 2019 20, PgNo.79, It.No.14.4.2) Single bracket 2 Mtr. Length	Specification: As specified in the tender document.	Nos	200
21	01/TEND/2020/RK/470//21	Supplying and fixing telescopic M.S. bracket fabricated by using 0.5m length 4 dia telescopic M. S. pipe, with 2 dia 1.5m long M. S. bracket and are welded with suitable angle, using 6mm thick M. S. sheet, grip bolts & nuts, as required, suitable for 9 to 12 Mtrs. M. S. tubular pole, with necessary two coats of painting, with all other accessories(PWD Electrical SR 2019 20, PgNo.79, It.No.14.4.2) Single bracket 2 Mtr. Length	Specification: As specified in the tender document.	Nos	150
22	01/TEND/2020/RK/470//22	Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS 694:1990(PWD Electrical SR 2019 20, PgNo.6, It.No.2.5.7) 2C X 2.5Sq.mm	Specification: As specified in the tender document.	Nos	4000
23	01/TEND/2020/RK/470//23	Supplying and Erection of 3 Phase, 11kV/433 V, 100kVA BEE 4/5 Star Rated Distribution Transformer Centre Using DPTS and all Accessories ( BESCOM SR 201617 CDS26) MR+LR	Specification: As specified in the tender document.	Nos	1
24	01/TEND/2020/RK/470//24	Fabricating, supplying and erection of rs long hot dip Galvanized Conical pole with BSEN 10025 grade S355JO steel plate for shaft, IS 2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to withstand the wind speed of 47 m/sec for Mtrs pole in single section and single joint welded as per IS 9595/IS 10178AWS having dimensions bottom mm, topmm with 3mm thick, suitable base plate and 4Nos of long J bolts along with template and the pole shall be hot dip galvanized in single dipping with not less than 65micron as per ASTM A123 and 153 etc.,(excluding foundation) as per drawing appended.(PWD Electrical SR 2019 20, PgNo.14, It.No.4.4.8) 10 meters Top 75mm and bottom 165 mm dia	Specification: As specified in the tender document.	Nos	130
25	01/TEND/2020/RK/470//25	Supplying of 1.1 KV LT UG cable having aluminium conductor PVC insulated, extruded inner sheathed, galvanised, steel strip (except 2CX10Sq.mm wire armoured) confirming to IS 3975:1990 (No. of Strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS 1554 Part 1:1988 & confirming to the attached GTP of GROUP A. as per the direction of work incharge engineer 3.5 core 35 sqmm (PWD Electrical SR 2019 20 Page No 40, Item No 6.4.6)	Specification: As specified in the tender document.	Nos	600
26	01/TEND/2020/RK/470//26	Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. as per the direction of work incharge engineer In soil (ordinary)(PWD Electrical SR 2019 20 Page No 41, Item No 6.6.1)	Specification: As specified in the tender document.	Nos	550
27	01/TEND/2020/RK/470//27	Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating etc., complete. as per the direction of work incharge engineer In soil (hard)(PWD Electrical SR 2019 20 Page No 42, Item No 6.6.2)	Specification: As specified in the tender document.	Nos	50
28	01/TEND/2020/RK/470//28	Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stoneware pipe / on wall / on pole as required. as per the direction of work incharge engineer 25 sqmm to 75 sqmm (PWD Electrical SR 2019 20 Page No 41, Item No 6.5.2)	Specification: As specified in the tender document.	Nos	600
29	01/TEND/2020/RK/470//29	Supplying and fiixing of heavy duty cable glands suitable for UG cable of 1.1 KV class (metal only)45mm dia(PWD Electrical SR 2019 20 Page No 42, Item No 6.11.4)	Specification: As specified in the tender document.	Nos	12
30	01/TEND/2020/RK/470//30	Supplying and running GI/Copper conductor for grounding and (along with other wires in conduit system of wiring) using necessary suitable size clamps, nails, guttas/spacers etc..( 64 / 7.22)(PWD Electrical SR 2019 20 Page No 44, Item No 6.18.6) Copper wire 8 SWG	Specification: As specified in the tender document.	Nos	30
31	01/TEND/2020/RK/470//31	Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes.f) 35 sqmm Long Barrel(PWD Electrical SR 2019 20 Page No 43, Item No 6.17.8	Specification: As specified in the tender document.	Nos	240
32	01/TEND/2020/RK/470//32	Fabricating supplying and mounting MS box made out SWG suitable for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled metal paint etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.42.1) 14SWG	Specification: As specified in the tender document.	Nos	300000
33	01/TEND/2020/RK/470//33	Supplying amps rated 3phase with neutral bus bar using required capacity electrolytic alluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary botls,nuts and washers etc., complete. (PWD Electrical SR 2019 20 Page No 30, Item No 5.40.1) 100Amps 4x30x6mm Alluminium Strips	Specification: As specified in the tender document.	Nos	4
34	01/TEND/2020/RK/470//34	Supplying and fixing angle iron frame work fabricated out of M.S. angle iron. and M.S. flat with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. (PWD Electrical SR 2019 20 Page No 30, Item No 5.41.2) 50X50X6mm	Specification: As specified in the tender document.	Nos	30
35	01/TEND/2020/RK/470//35	Supplying and fixing Microprocessor based Electronic timer (without contactor, Din Mounting using necessary bolts, nuts and washers etc.,.) as per the direction of work incharge engineer 3 120sec. ( PWD Electrical SR 2019 20 Page No 32, Item No 5.47)	Specification: As specified in the tender document.	Nos	6
36	01/TEND/2020/RK/470//36	Supply and fixing of 4pole power contactor with NO/NC contacts on existing wood/panel board using necessary bolts, nuts, washers and wiring etc., complete with AC 3 Rating and as per IS 13947. as per the direction of work incharge engineer( ( PWD Electrical SR 2019 20 Page No 26, Item No 5.13.1) a) 25Amps	Specification: As specified in the tender document.	Nos	12
37	01/TEND/2020/RK/470//37	Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts and wiring complete. Protection of Overload and Short circuit with thermal Magnetic/Microprocessed release and Earth Fault as per IS 13947. ( Icu = Ics) (PWD Electrical SR 201920 Page No 26, Item No 5.14.1) Four Pole,100Amps 25kA.	Specification: As specified in the tender document.	Nos	8
38	01/TEND/2020/RK/470//38	KSRB 2 2 : Earthwork excavation by manual means for foundation of buildings, water supply and sanitary lines and electrical conduits etc, either in pits or in trenches 1.5m and above in width, in soil not exceeding 1.5 m. in depth including dressing the bottom and sides of pits and trenches, stacking the excavated soil clear from edges of excavation with lead upto 50 m. including breaking of clods complete as per specifications in ordinary soil..(PWD Civil SR 2018 19, Pg.No.6, It.No.2.3) For High mast	Specification: As specified in the tender document.	Nos	21
39	01/TEND/2020/RK/470//39	Supplying and fixing of MODULAR MCB Devices( Tripper) With Breaking capacity of 6KA.. (PWD Electrical SR 2019 20, PgNo.31, It.No.5.46.1 &5.46.3) 63 Amps SP	Specification: As specified in the tender document.	Nos	6
40	01/TEND/2020/RK/470//40	Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc, the pipe shall have 16 through holes of 122 mm dia ( 55 / 7.1) (PWD Electrical SR 2019 20 Page No 40, Item No 6.1)	Specification: As specified in the tender document.	Nos	6
41	01/TEND/2020/RK/470//41	Supplying PVC/GI flexible conduit pipe50mm fixing on surface over inverted tapered wooden plugs or phill plugs or rawl plugs and clamped using heavy gauge saddles at an interval of 300mm using NF screws and on either end of the pipe terminated completely(PWD Electrical SR 2019 20, PgNo.3, It.No.1.9.5 )	Specification: As specified in the tender document.	Nos	60
42	01/TEND/2020/RK/470//42	Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper with low conductor confirming to IS:8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100Volts as per IS 694:1990(PWD Electrical SR 2019 20, PgNo.6, It.No.2.5.7) 8C X 2.5Sq.mm	Specification: As specified in the tender document.	Nos	200
43	01/TEND/2020/RK/470//43	Fabrication, Supplying, Erection, Testing and Commissioning of Mtrs long polygon high mast with Single / Multiple telescopic sections having, (minimum overlap distance of 1.5 times of top section) thickness as per BSEN 10025 grade S 355 JO /ASTM A572 50 steel sheet plate for shaft suitable to withstand a wind velocity of 47 m/sec as per IS 875 part 3(as per GA Drawing).Base plate as per IS 2062/ASTM A572 50. The mast shall be Galvanized in single Hot-dip as per BSEN ISO 1461/ASTM A123 with an average 70 microns as per IS 2629, and welded as per BS 5135 Single L Seam joint. The mast shall have 2way head frame with die cast LM 6 pulleys, stainless steel axle, Phosphorus Bronze bearing bush press fitted with separate guides for 2 runs of 5mm dia, stainless steel wire rope of AISI 304grade 7/19core, (Factor of Safety as per TR no 7). 2.5sqmm EPR insulated PCP sheathed trailing power cable housed inside the bottom shaft of mast with door having locking arrangement. The mast shall have manual / power tool (Suitable reversible geared motor operating on 230/ 415V, 50Hz, shall be provide above 15 Mtrs mast) The mast shall have lantern of 2 segments, suitable dia with max load carrying capacity as per IS 1239. The mast shall be erected on existing RCC footing. The mast shall be supplied with 3mm thick template, lightning arrester of 1.2m length galvanized pipe with top arrow fitted on top of the head frame cover and GLS type aviation twin lamps fitting with wiring complete. (excluding foundation) as per technical data.(PWD Elecrical SR 2019 20 P.No 15 It.No.4.5.2) 16Mtrs Top 150mm and bottom 410 mm dia	Specification: As specified in the tender document.	Nos	5
44	01/TEND/2020/RK/470//44	Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete(PWD Electrical SR 2019 20, PgNo.16, It.No.4.7.5) Double Arm Bracket with 1500mm Standard 40/50MM dia	Specification: As specified in the tender document.	Nos	36
45	01/TEND/2020/RK/470//45	Supplying and fixing Electronic Trivector Meter (ETV) suitable for operation LT operation and CT operated meter in polycarbonate body in class 0.5 accuracy as per IS 14697 and completely wired (PWD Electrical SR 2019 20, PgNo.29, It.No.5.31)	Specification: As specified in the tender document.	Nos	6
46	01/TEND/2020/RK/470//46	Supplying and fixing of class A (medium duty) GI pipe of wall thickness not less than 3.25mm on pole/wall/drain crossing with necessary clamping arrangements for UG cable of 1.1 KV. 65mm (PWD Electrical SR 2019 20, PgNo.42, It.No.6.9.3)	Specification: As specified in the tender document.	Nos	60
47	01/TEND/2020/RK/470//47	Providing and laying in position 100mm dia stone ware pipe in existing trench. (PWD Electrical SR 2019 20, PgNo.41, It.No.6.8)	Specification: As specified in the tender document.	Nos	180
48	01/TEND/2020/RK/470//48	KSRB 4 1.3 : Providing and laying in position plain cement concreteof Mix 1:4:8 with OPC @ 180kgs, with 40mm and down size gradedgranite metal coarse aggregates @0.85cum and fine aggregates @0.57cum machine mixed, machine mixed, concrete laid in layers notexceeding 15 cms. thick, well compacted, in foundation, including costof all materials, labour, HOM curing complete as per specifications. Specification No. KBS 4.1, 4.2 (PWD Civil SR 2018 19 P.NO13, It.No. 4.3)	Specification: As specified in the tender document.	Nos	54
49	01/TEND/2020/RK/470//49	KSRB 4 1.6 ; Providing and laying in position plain cement concrete of Mix 1:2:4 with OPC @ 240kgs, with 20mm and down size graded granite metal coarse aggregates @ 0.878 cum and fine aggregtes @ 0.53cum, machine mixed, concrete laid in layers not exceeding 15 cms. thick, well compacted, in foundation, plinth and cills, including cost of all materials, labour, HOM curing complete as per specifications. Specification No. KBS 4.1, 4.2(PWD Civil SR 2018 19 P.NO13, It.No. 4.6)	Specification: As specified in the tender document.	Nos	30
50	01/TEND/2020/RK/470//50	KSRB 4.9.2 : Providing T.M.T steel reinforcement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary complete as per design (laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM complete as per specifications. Specification No. KBS 4.6.3 TMT bars Fe 500(PWD Civil SR 2018 19 P.NO18, It.No. 4.46.2)	Specification: As specified in the tender document.	Nos	1.2
51	01/TEND/2020/RK/470//51	Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm.Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with W System Power consumption. LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. (PWD Electrical SR 2019 20 P.No 67 It.No 12.9.4) LED Floodlight 150W	Specification: As specified in the tender document.	Nos	50