Council Of Scientific And Industrial Research-CSIR has published Amc Of Lab Building 2020 21 Civil Work The Work Includes Maintenance Of Lab Building In Term Of Plaster Repair And Finishing Work Brick Work Wooden Work Flooring Work Steel Work Aluminum Work Interior Exterior Painting All Water Supply And Sanitary Work. Submission Date for this Tender is 11-12-2020. Civil Work Tenders in CSIR-IIP Dehradun Uttarakhand. Bidders can get complete Tender details and download the document.
| Name of Work: AMC of Lab Building 2020-21 (civil) | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Earth work All kinds of soil in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. | Item No 01 | 12 | cum |
| 2 | 2 | Surface dressing All kinds of soil of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. | Item No 02 | 100 | sqm |
| 3 | 3 | Supplying chemical emulsion in sealed containers including delivery as specified : Chlorpyriphos/ Lindane emulsifiable concentrate of 20%. | Item No 03 | 20 | litre |
| 4 | 4 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. | Item No 04 | 50 | sqm |
| 5 | 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). | Item No 05 | 10 | cum |
| 6 | 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, ifnishing and reinforcement- All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). | Item No 06 | 7 | cum |
| 7 | 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III)derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). | Item No 07 | 2 | cum |
| 8 | 8 | Centering and shuttering including strutting, propping etc. and removal of form for : | Item No 08 | ||
| 9 | 8.01 | Shelves (Cast in situ) | Item No 09 | 18 | sqm |
| 10 | 8.02 | Lintels, beams, plinth beams, girders, bressumers and cantilevers | Item No 10 | 18 | sqm |
| 11 | 9 | Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. | Item No 11 | 500 | kg |
| 12 | 10 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand). | Item No 12 | 3 | cum |
| 13 | 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand). | Item No 13 | 2 | cum |
| 14 | 12 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level: Cement mortar 1:4 (1 cement :4 coarse sand). | Item No 14 | 18 | sqm |
| 15 | 13 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels: Granite of any colour and shade Area of slab over 0.50 sqm. | Item No 15 | 8 | sqm |
| 16 | 14 | Providing and fixing 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. | Item No 16 | 13 | sqm |
| 17 | 15 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. | Item No 17 | 30 | each |
| 18 | 16 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. | Item No 18 | 5 | each |
| 19 | 17 | Providing and fixing 300x16 mm aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete. | Item No 19 | 20 | each |
| 20 | 18 | Providing and fixing 150x10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. | Item No 20 | 50 | each |
| 21 | 19 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : | Item No 21 | ||
| 22 | 19.01 | 125 mm | Item No 22 | 20 | each |
| 23 | 19.02 | 100 mm | Item No 23 | 50 | each |
| 24 | 20 | Providing and fixing aluminium hanging Twin rubber floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. | Item No 24 | 25 | each |
| 25 | 21 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. | Item No 25 | 25 | metre |
| 26 | 22 | Providing and fixing 30 mm thick plain factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. | Item No 26 | 8 | sqm |
| 27 | 23 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Item No 27 | 300 | kg |
| 28 | 24 | Steel work Hot finished welded type tubes in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. | Item No 28 | 450 | kg |
| 29 | 25 | Cement concrete flooring 40 mm thick with 20 mm nominal size stone aggregate1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. | Item No 29 | 30 | sqm |
| 30 | 26 | Providing and fixing 40 mm wide and 4 mm thick glass strips in joints of terrazo/ cement concrete floors. | Item No 30 | 40 | metre |
| 31 | 27 | Providing and laying Double charge Vitrified tiles polished finish of size of Tile 600 x 600 mm in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. | Item No 31 | 56 | sqm |
| 32 | 28 | Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -10. | Item No 32 | 216 | sqm |
| 33 | 29 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. | Item No 33 | ||
| 34 | 29.01 | 75 mm diameter | Item No 34 | 20 | metre |
| 35 | 29.02 | 110 mm diameter | Item No 35 | 30 | metre |
| 36 | 30 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. | Item No 36 | ||
| 37 | 30.01 | Single tee without door 75x75x75 mm | Item No 37 | 3 | each |
| 38 | 30.02 | Single tee without door 110x110x110 mm | Item No 38 | 3 | each |
| 39 | 30.03 | Bend 87.5° 75 mm bend | Item No 39 | 3 | each |
| 40 | 30.04 | Bend 87.5° 110 mm bend | Item No 40 | 3 | each |
| 41 | 31 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Item No 41 | 126 | sqm |
| 42 | 32 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : | Item No 42 | ||
| 43 | 32.01 | Ridges plain (500 - 600mm) | Item No 43 | 10 | metre |
| 44 | 32.02 | Gutter (600 mm over all girth) | Item No 44 | 12 | metre |
| 45 | 33 | Providing and fixing GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. Tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. | Item No 45 | 36 | sqm |
| 46 | 34 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand). | Item No 46 | 100 | sqm |
| 47 | 35 | Distempering Two or more coats on new work with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. | Item No 47 | 400 | sqm |
| 48 | 36 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). | Item No 48 | 216 | sqm |
| 49 | 37 | Finishing with Epoxy paint (two or more coats) On concrete work at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. | Item No 49 | 50 | sqm |
| 50 | 38 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. | Item No 50 | 100 | sqm |
| 51 | 39 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Item No 51 | 200 | sqm |
| 52 | 40 | White washing with lime to give an even shade : Old work (two or more coats). | Item No 52 | 200 | sqm |
| 53 | 41 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete | Item No 53 | 400 | sqm |
| 54 | 42 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :Old work (one or more coats). | Item No 54 | 400 | sqm |
| 55 | 43 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. | Item No 55 | 150 | sqm |
| 56 | 44 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). | Item No 56 | 500 | sqm |
| 57 | 45 | Demolishing Nominal cement concrete 1:3:6 or richer mix (i/c equivalent design mix)manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. | Item No 57 | 6 | cum |
| 58 | 46 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | Item No 58 | 3 | cum |
| 59 | 47 | Demolishing brick work In cement mortar manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. | Item No 59 | 2 | cum |
| 60 | 48 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below. | Item No 60 | 10 | each |
| 61 | 49 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below. | Item No 61 | 10 | each |
| 62 | 50 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : Thickness above 25 mm up to 40 mm. | Item No 62 | 18 | sqm |
| 63 | 51 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge : | Item No 63 | ||
| 64 | 51.01 | 15 mm to 40 mm nominal bore | Item No 64 | 200 | metre |
| 65 | 51.02 | Above 40 mm nominal bore | Item No 65 | 100 | metre |
| 66 | 52 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | Item No 66 | 100 | sqm |
| 67 | 53 | Supplying and stacking at site:63 mm to 45 mm size stone aggregate. | Item No 67 | 13 | cum |
| 68 | 54 | Fencing With G.I. barbed wire with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. | Item No 68 | 480 | metre |
| 69 | 55 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. | Item No 69 | 2 | each |
| 70 | 56 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid. | Item No 70 | 2 | each |
| 71 | 57 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap. | Item No 71 | 2 | each |
| 72 | 58 | Providing and fixing white vitreous china laboratory sink Size 600x450x200 mmwith C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required. | Item No 72 | 2 | each |
| 73 | 59 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete:Flexible pipe 32 mm dia. | Item No 73 | 30 | each |
| 74 | 60 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall | Item No 74 | ||
| 75 | 60.01 | 15 mm dia nominal bore | Item No 75 | 100 | metre |
| 76 | 60.02 | 20 mm dia nominal bore | Item No 76 | 250 | metre |
| 77 | 60.03 | 40 mm dia nominal bore | Item No 77 | 40 | metre |
| 78 | 60.04 | 50 mm dia nominal bore | Item No 78 | 30 | metre |
| 79 | 61 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work | Item No 79 | ||
| 80 | 61.01 | 15 mm dia nominal bore | Item No 80 | 50 | metre |
| 81 | 61.02 | 20 mm dia nominal bore | Item No 81 | 100 | metre |
| 82 | 61.03 | 40 mm dia nominal bore | Item No 82 | 30 | metre |
| 83 | 62 | Providing and fixing 50 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end). | Item No 83 | 2 | each |
| 84 | 63 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : | Item No 84 | ||
| 85 | 63.01 | 15 mm nominal bore | Item No 85 | 10 | each |
| 86 | 63.02 | 20 mm nominal bore | Item No 86 | 20 | each |
| 87 | 64 | Providing and fixing uplasticised 45 cm length 15 mm nominal bore PVC connection pipe with brass unions. | Item No 87 | 40 | each |
| 88 | 65 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : | Item No 88 | ||
| 89 | 65.01 | 15 mm nominal bore | Item No 89 | 15 | each |
| 90 | 65.02 | 20 mm nominal bore | Item No 90 | 25 | each |
| 91 | 66 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Item No 91 | 2000 | per litre |
| 92 | 67 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931. | Item No 92 | 5 | each |
| 93 | 68 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. | Item No 93 | 10 | each |
| 94 | 69 | Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 | Item No 94 | 10 | each |
| 95 | 70 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. | Item No 95 | ||
| 96 | 70.01 | 15 mm nominal bore, 105 mm long, weighing not less than 138 gms | Item No 96 | 30 | each |
| 97 | 70.02 | 20 mm nominal bore, 120 mm long, weighing not less than 198 gms | Item No 97 | 20 | each |
| 98 | 70.03 | 40 mm nominal bore, 206mm long, weighing not less than 690 gms | Item No 98 | 5 | each |
| 99 | 70.04 | 50 mm nominal bore, 242mm long, weighing not less than 1240 gms | Item No 99 | 2 | each |
| 100 | 71 | Providing and fixing aluminium work For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately). | Item No 100 | 220 | kg |
| 101 | 72 | Providing and fixing aluminium work Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). | Item No 101 | 120 | kg |
| 102 | 73 | Providing and fixing 12 mm thick prelaminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. | Item No 102 | 30 | sqm |
| 103 | 74 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm). | Item No 103 | 36 | sqm |
| 104 | 75 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. | Item No 104 | 10 | each |
| 105 | 76 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). | Item No 105 | 25 | kg |
| 106 | 77 | Providing and fixing SS hand railing with all complete as per direction of Engineer's - in- charge. | Item No 106 | 50 | kg |
| 107 | 78 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm with all complete as per Engineer-in-charge etc. | Item No 107 | 60 | sqm |
| 108 | 79 | Providing and fixing of Aluminium Doors floor spring/floor machine (Heavy duty) etc. | Item No 108 | ||
| 109 | 79.01 | Small size | Item No 109 | 2 | each |
| 110 | 79.02 | Big size | Item No 110 | 4 | each |
| 111 | 80 | Providing and fixing CP brass pillar cock etc. | Item No 111 | 5 | each |
| 112 | 81 | Providing and fixing Shower with shower arm etc. | Item No 112 | 6 | each |
| 113 | 82 | Providing and fixing seat jet etc. | Item No 113 | 15 | each |
| 114 | 83 | Providing and fixing Spandal (Jaguar make) etc. | Item No 114 | 20 | each |
| 115 | 84 | Providing and fixing WC seat cover cascade etc. | Item No 115 | 15 | each |
| 116 | 85 | Supplying and filling fine sand etc. | Item No 116 | 6 | cum |
| 117 | 86 | Providing and fixing false ceiling perforated sheet 600 x 600 mm with all complete etc. | Item No 117 | 30 | each |
| 118 | 87 | Repair and removing and re- fixing of existing Aluminium Door & window in existing frame etc. | Item No 118 | 40 | each |
| 119 | 88 | Providing and fixing steel hinges heavy duty etc. | Item No 119 | 50 | each |
| 120 | 89 | Providing and fixing 5 mm thick chequered plate with complete as per Engineer-in-charge etc. | Item No 120 | 400 | kg |
| 121 | 90 | Labour Mandays Un-skilled in mandays. | Item No 121 | 160 | days |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
