| 1 | 1 | Excavating over areas not exc 1.5m deep and getting out in soft/loose soil complete all as specified and as directed. | | 39.01 | Cum |
|---|
| 2 | 2 | Excavating over areas exc 1.5m deep but not exc 3.0m deep getting out in soft/loose soil complete all as specified and as directed. | | 14.3 | Cum |
|---|
| 3 | 3 | Excavating in trenches, not exc 1.5 metre wide and not exc 1.5 metre in depth, for foundation, filling mass concrete or for shafts, wells, cesspits, manholes, pier holes, laying cables, pipes, etc. not exc 10 Sqm on plan & not exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. | | 651.76 | Cum |
|---|
| 4 | 4 | Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified and as directed. | | 669.83 | Cum |
|---|
| 5 | 5 | Removing excavated soil/material to a distance n. exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified and as directed. | | 31.48 | Cum |
|---|
| 6 | 6 | M&L PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. | | 6.36 | Cum |
|---|
| 7 | 7 | M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter (rough finished surface) complete all as specified and as directed. | | 6.54 | Sqm |
|---|
| 8 | 8 | M&L Reinforced cement concrete M-30 (design Mix) using 20 mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and as directed ( Note :- Reinforcement & formwork shall be measured and paid for separately.) | | 5.06 | Cum |
|---|
| 9 | 9 | M&L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc vertical or to batter (rough finished surface) complete all as specified and as directed. | | 69.7 | Sqm |
|---|
| 10 | 10 | M&L Reinforced cement concrete M-30 (design Mix) using 20 mm graded crushed stone aggregates as in walls, retaining walls, basement walls, ballast walls and the like, any thickness , above top of footings, including attached pilasters and buttresses complete all as specified and as directed. ( Note :- Reinforcement & formwork shall be measured and paid for separately.) | | 8.76 | Cum |
|---|
| 11 | 11 | M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete, complete all as specified and as directed. | | 18.7 | Sqm |
|---|
| 12 | 12 | M&L Reinforced cement concrete M-30 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like complete all as specified & as directed. ( Note :- Reinforcement & formwork shall be measured and paid for separately.) | | 3.03 | Cum |
|---|
| 13 | 13 | M&L Reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. | | 573.81 | Kg |
|---|
| 14 | 14 | M&L Reinforcement TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & as directed. | | 1107.82 | Kg |
|---|
| 15 | 15 | M&L Rendering 5mm thick in cement mortar 1:3 on concrete surfaces finished even & smooth without using extra cement complete all as specified & as directed. | | 78.05 | Sqm |
|---|
| 16 | 16 | M&L Preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer ( white cement wash) complete all as specified & as directed. | | 29.25 | Sqm |
|---|
| 17 | 17 | M&L Wire netting of galvanised steel wire 1.40mm dia, mesh size 25mmx25mm fixed with tinned tacks of wire staples as in tree guards complete all as specified & as directed. | | 112.8 | Sqm |
|---|
| 18 | 18 | M&L Mild steel angle iron Posts and Struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 complete all as specified & as directed. | | 1161 | Kg |
|---|
| 19 | 19 | M&L Preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide zinc chrome primer complete all as specified. | | 56 | Sqm |
|---|
| 20 | 20 | Supply & fixing 3-layer PP-R (Polypropylene random copolymer) pipe, 63mm outer dia, as per IS-15801:2008, SDR 7.4 (PN-16) stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings for main distribution line in Irrigation system etc complete all as specified and as directed. (Note : ISI licenced makes with CML number shall be approved by GE Prior to Procument by Contractor.) | | 1850 | RM |
|---|
| 21 | 21 | Supply & fixing 3-layer PP-R (Polypropylene random copolymer) pipe, 50mm outer dia, as per IS-15801:2008, SDR 7.4 (PN-16) stabilized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings for main distribution line in Irrigation system etc complete all as specified and as directed. (Note : ISI licenced makes with CML number shall be approved by GE Prior to Procument by Contractor.) | | 570 | RM |
|---|
| 22 | 22 | Supply and fixing PP-R TEE of size 50mmx25mmx50mm dia for water sub distribution line in irrigation system including accessoies complete all as specified & as directed. | | 44 | Each |
|---|
| 23 | 23 | Supply and fixing PP-R Distribution Valve (Th. End) of size 25mm dia for water sub distribution line in irrigation system including accessoies complete all as specified & as directed. | | 44 | Each |
|---|
| 24 | 24 | Supply and fixing PP-R Distribution Vallve (Th. End) of size 50mm dia for water sub distribution line in irrigation system Including accessoies complete all as specified & as directed. | | 3 | Each |
|---|
| 25 | 25 | Supply and fixing PP-R Cast Iron Butterfly Valve (Th. End) of size 63mm dia for water sub distribution line in irrigation system including accessoies complete all as specified & as directed. | | 1 | Each |
|---|
| 26 | 26 | Supply and fixing PP-R End cap of size 50mm dia for water distribution line in irrigation system including accessoies complete all as specified & as directed. | | 2 | Each |
|---|
| 27 | 27 | Supply and fixing PP-R Reducer socket of size 50mmx25mm dia for water distribution line in irrigation system including accessoies complete all as specified & as directed. | | 1 | Each |
|---|
| 28 | 28 | Supply and fixing PP NRV of size 63mm dia with capacity of (10kg/cm2) for water distribution Main line in irrigation system and all including accessoies complete all as specified & as directed. | | 2 | Each |
|---|
| 29 | 29 | Supply and fixing PP Foot valve of size 63mm dia with capacity of (10kg/cm2) for water distribution Main line in irrigation system and all including accessoies complete all as specified & as directed. | | 2 | Each |
|---|
| 30 | 30 | M&L Connection by cutting existing under ground DI Pipe of size 150mm dia for inserting of tee size 150mmx150mmx80mm dia including necessary earth work dewatering etc and all fittings complete all as specified & directed | | 1 | Each Job |
|---|
| 31 | 31 | M&L DI reducer of size 80mmx63mm dia for Connection of PP-R 63 mm dia side flange ended type including necessary earth work and all fittings complete all as specified & directed | | 1 | Each |
|---|
| 32 | 32 | M&L MS flange size 63mm dia suitable for PP-R pipe 63mm dia complete all as specified & directed | | 2 | Each |
|---|
| 33 | 33 | Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, suitable for CI/DI pipe line and testing, complete all as specified & as directed. | | 1 | Each Job |
|---|
| 34 | 34 | M&L for Valve Pit of internal size 60cm x 60cm x 60cm built in brick masonry complete all as specified in Particular Specifications and as shown on drawing No. BTD-811 Sheet No. 1/2 & 2/2. | | 2 | Each Job |
|---|
| 35 | 35 | Supply, Install, testing and commissioning of Monoblock pump set 2 HP capacity, electrically driven with supply voltage 240V , single Phase 50Hz 3000 RPM with discharge capacity 200 LPM at 20 Mtr head, suction and delivery 50mm x 50mm including all fitting such as MS flanges-2 nos and suitable size foundation 30CM height with PCC (1:2:4) type B-2 using 40mm graded aggregate finished fair etc & including necessary fixing arrangement complete all as specified & as directed. | | 2 | Each Job |
|---|
| 36 | 36 | M&L for Earthing to Transformer / GOD switch / equipments / panels etc with & including galvaniged mild steel earth plate electrode of size 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including galvanized mild steel strip 32x6 mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to transformer / GOD / Panel / equipment body / test point with two Nos nuts bolts or welding with steel structure, GI earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed including dismantling. Note : PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner | | 6 | Each Set |
|---|
| 37 | 37 | Supply, laying, jointing and testing LT XLPE insulated screened, bedded, galvanised steel strip or wire armoured heavy duty electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 6 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified .\nNotes :-\n(i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.\n(ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.\n | | 40 | RM |
|---|
| 38 | 38 | M&L for dry sand cushioning (river sand) gently punning to required thickness as in for protection of under ground electric cable complete all as specified and as directed.\nNotes :-\n(i) Approved local Tibba dry sand free from vegetations, grass and other deleterious substances shall be used.\n(ii) For the purpose of payment, only punned thickness shall be measured. | | 6 | Cum |
|---|
| 39 | 39 | M&L for sub class ‘B’ (old size) burnt clay bricks laid flat and dry abutting each other with gap between adjacent bricks not exc. 10mm for protection of underground electric cable in such a way that the length of brick is at right angle to the central axis of cable complete all as specified and as directed. | | 0.24 | Per 1000 Nos |
|---|
| 40 | 40 | S&F Direct on line (DOL) starter for pump, in sheet steel enclosure, suitable for 2 HP motor, rating 240 volts Duty, 50 Hz, single phase with & including single phase preventer, phase reversal and over current protection with digital Amp meter with built in selector switch and testing complete all as specified & directed. | | 2 | Each |
|---|
| 41 | 41 | Supply and fixing sheet metal box Fabricated of size 60cm x 45cm x 45cm made out of 3.15mm thick CRCA sheet mounted on 50 x 50 x 6mm angle iron frame, 30 cm above ground level and 30 cm grouted in to floor with necessary PCC, vermin proof, dust proof with locking arrangement duly powder coated of approved colour and making provision for housling DOL starter-02 Nos & MCB SPN 32 Amp-2 Nos ( including one spare) including all required incoming and outgoing cable connections, complete all as specified & as directed. (Note :- MCB & DOL starter will be measured and paid for separately.) | | 1 | Each Job |
|---|
| 42 | 42 | Supply and fixing Fabricated cage of suitable size made out of flat iron / angle iron to cover the monoblock pumping set alongwith motor safety including nuts, bolts and washers painting with two coats of synthetic enamel paint of approved shade over a coat of red oxide prime complete all as specified & as directed. | | 0.8 | Qtl |
|---|
| 43 | 43 | S&F MCB, Single Pole, 6-32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, complete all as specified & directed. | | 2 | Each |
|---|
| 44 | 44 | M&L Boring of holes under road, pavement, hard standing, etc by trench less technology using ultra sound technique and necessary machine suitable for passing the pipe upto 50mm bore including provision of GI Pipe light grade of 50 mm bore (ISI marked) with including all fittings with the drilled holes, returning, filling in the end working space icluding removal soil and making good the surfaces complete all as specified and as directed. | | 40 | RM |
|---|
| 45 | 45 | Supply and fixing Ductile Iron (DI) fittings, specials such as bends, tapers, collars, reducers, tee pieces (single or double branch) any type, angle/radius and straight connecting pieces etc (ISI marked) conforming to IS 9523 for flanged/socket and spigot ends suitable for DI pipe upto 150 mm bore with jointing material complete all as specified and directed. | | 60 | Kg |
|---|
| 46 | 46 | M&L brick work with old size burnt clay sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified and as directed. | | 2 | Cum |
|---|
