| 1 | 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.Depth upto 1.5m from existing ground level (Rate include 1% labour cess) | BI01010001010000000000000515BI0100001112 | 1441.91 | Cum |
|---|
| 2 | 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (Rate include 1% labour cess) | | 573.53 | Cum |
|---|
| 3 | 3 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.\nNote - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more. | | 600 | Cum |
|---|
| 4 | 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level. 1:4:8 (1 Cement:4 coarse sand:8 graded stone aggregate 40 mm nominal size) | | 318.53 | Cum |
|---|
| 5 | 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.\n(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). | | | |
|---|
| 6 | 6 | All works upto plinth level | | 549.85 | Cum |
|---|
| 7 | 7 | All works above plinth level upto floor V level | | 1300.61 | Cum |
|---|
| 8 | 8 | Extra for providing richer mixes at all floor levels.\nNote:- Excess/less cement over the specified cement content used is payable /recoverable separately. | | | |
|---|
| 9 | 9 | Providing M-30 grade concrete instead of M-25 grade BMC/RMC. \n(Note:- Cement content considered in M-30 is @ 340 kg/cum) | | 1619.15 | Cum |
|---|
| 10 | 10 | Cenetring and shuttering including strutting, propping etc. and removal of form for: | | | |
|---|
| 11 | 11 | Suspended floors, roofs,landings, balconies and access platform with water proof ply 12 mm thick | | 1250 | Sqm |
|---|
| 12 | 12 | Columns, Pillars, Piers, Abutments, Posts and Struts | | 1460 | Sqm |
|---|
| 13 | 13 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick | | 1870 | Sqm |
|---|
| 14 | 14 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars | | 317758 | Kg |
|---|
| 15 | 15 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) | | 706.96 | Cum |
|---|
| 16 | 16 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). | | | |
|---|
| 17 | 17 | Second class teak wood | | 1.13 | Cum |
|---|
| 18 | 18 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:Butt hinges and necessary screws shall be paid separately) | | | |
|---|
| 19 | 19 | Second class teak wood 35 mm thick shutters | | 70.7 | Sqm |
|---|
| 20 | 20 | Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | | 1918.08 | Kg |
|---|
| 21 | 21 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) | | 6032.05 | Sqm |
|---|
| 22 | 22 | Finishing walls with Acrylic Smooth exterior paint of required shade : | | | |
|---|
| 23 | 23 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | | 6032.05 | Sqm |
|---|
| 24 | 24 | Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @ 0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. | | 1451.59 | Sqm |
|---|
| 25 | 25 | Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge. | | 2889.46 | Sqm |
|---|
| 26 | 26 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. | | 4155.55 | Cum |
|---|
| 27 | 27 | Providing and laying 60mm thick factory made cement concrete paver block of approved shape and colour of M -30 grade made of C&D waste by block making machine with vibratory compaction laid in required pattern and including over 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-incharge. | | 4267.07 | Sqm |
|---|
| 28 | 28 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge.\n(The panel shuttering work shall be paid for separately).\n(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). | | 270 | Cum |
|---|
| 29 | 29 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. | | | |
|---|
| 30 | 30 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | | 1650 | Kg |
|---|
| 31 | 31 | PLUMBING & SANITARY WORK | | | |
|---|
| 32 | 32 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : | | | |
|---|
| 33 | 33 | W.C. pan with ISI marked white solid plastic seat and lid | | 14 | Nos. |
|---|
| 34 | 34 | Providing and fixing wash basin with C.I. Brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls whereever require : | | | |
|---|
| 35 | 35 | White Vitreous China Flat back wash basin size 550x\n400 mm with single 15 mm C.P. brass pillar tap | | 14 | Nos. |
|---|
| 36 | 36 | Providing and fixing white vitreous china flat back half stall urinal of size 580 x 380x350 mm with white P.V.C automatic flushing cistern, with fittings, standard size C.P brass flush pipe, spreaders with unions and clamps (all in C.P brass) with waste fitting as per IS : 2556, C.I trap with outlet grating and other coupling in C.P brass including painting of fittings and cutting and making good the walls and floors whereever required | | | |
|---|
| 37 | 37 | Range of two half stall urinals with 5 litre P.V.C automatic flushing cistern | | 12 | Nos. |
|---|
| 38 | 38 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | | 14 | Nos. |
|---|
| 39 | 39 | Providing and fixing PTMT angle stop cock 15mm nominal bore,weighting not less than 85gms. | | 28 | Nos. |
|---|
| 40 | 40 | Providing and fixing PTMT Bottle Trap for Wash basin: | | | |
|---|
| 41 | 41 | Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms. | | 28 | Nos. |
|---|
| 42 | 42 | Providing and fixing 8 mm dia C.P / S.S. Jet with flexible tube upto 1 meter long with S.S triangular plate to Eureopean type W.C of quality and make as approved by Engineer-in-charge | | 14 | Nos. |
|---|
| 43 | 43 | Providing and fixing PTMT grating of approved quality and colour. | | | |
|---|
| 44 | 44 | Circular/square type 100 mm nominal dia/size. | | 6 | Nos. |
|---|
| 45 | 45 | SOIL, WASTE , VENT WATER PIPES | | | |
|---|
| 46 | 46 | Providing and fixing soil, waste and vent pipes | | | |
|---|
| 47 | 47 | Centrifugally cast (spun) iron socket & Spigot (S & S) Pipe as per IS 3989 | | 225 | Rm |
|---|
| 48 | 48 | Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc. 100mm dia | | 45 | Nos. |
|---|
| 49 | 49 | Providing and fixing plain bend of required degree. 100mm dia sand cast iron S & S as per IS: 3989 | | 32 | Nos. |
|---|
| 50 | 50 | Providing and fixing single equal plain junction of required degree . 100 x 100 x 100mm sand cast iron S & S as per IS: 3989 | | 32 | Nos. |
|---|
| 51 | 51 | Providing and fixing terminal guard. 100mm dia sand cast iron S & S as per IS: 3989 | | 32 | Nos. |
|---|
| 52 | 52 | Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre: 100mm dia | | 32 | Nos. |
|---|
| 53 | 53 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100mm inlet and 100mm outlet sand cast iron S & S as per IS: 3989 | | 32 | Nos. |
|---|
| 54 | 54 | Internal work- Exposed on wall | | | |
|---|
| 55 | 55 | 32mm nominal bore | | 28 | Rm |
|---|
| 56 | 56 | 40mm nominal bore | | 28 | Rm |
|---|
| 57 | 57 | Painting GI pipes and fittings with two coats of anti corrosive bitumestic paint of approved quality. | | | |
|---|
| 58 | 58 | 32mm nominal bore | | 28 | Sqm |
|---|
| 59 | 59 | 40mm nominal bore | | 28 | Sqm |
|---|
| 60 | 60 | Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work | | | |
|---|
| 61 | 61 | 100mm diameter pipe | | 100 | Sqm |
|---|
| 62 | 62 | Providing and fixing single unequal plain invert branch of required degree : 100 x 100 x 75mm sand cast iron S & S as per IS: 3989 | | 14 | Nos. |
|---|
| 63 | 63 | Providing and fixing on wall face unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A, including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter | | 18 | Rm |
|---|
