Repairs Maintenance To Submersible Pumps Fountain Motors And Allied Works Services At North Camp Happy Home 820 Su Begam Bazaar 14 Psu And 71 Rmu At Bamrauli
Tender Value
Ref. Documents
Estimated cost
Bid Submission
19 Oct 2020
0 days left
EMD
30000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bamrauli → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repairs Maintenance To Submersible Pumps Fountain Motors And Allied Works Services At North Camp Happy Home 820 Su Begam Bazaar 14 Psu And 71 Rmu At Bamrauli
BOQ
| Name of Work: REPAIR/ MAINT TO SUBMERSIBLE PUMPS, FOUNTAIN MOTORS AND ALLIED WORK SERVICES AT NORTH CAMP, HAPPY HOME, 820 SU, BEGAM BAZAR, 14 PSU AND 71 RMU AT BAMRAULI | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Taking out submersible pump set of capacity 5 to 10 HP, three phase, any type from bore well by disconnecting all electrical and mechanical connections including connected items of pump such as column pipes complete for checking, replacement of cable and repair of pump including lowering & reassembling the pump in the existing position by reconnecting after repair of pump including packing materials, nut bolts, securing of submersible in column pipe by using insulated wires, cable jointing materials etc, testing and commissioning complete all as specified and directed.\nNote:- The unit ratre quoted is deemed to be inclusive of washers, studs & nuts, nut & bolts, packing materials and other minor spare parts upto Rs.200/-/Each\n | 1 | Each Job | |
| 2 | 2 | All as per item No.1 above but 15 to 20 HP capacity | 2 | Each Job | |
| 3 | 3 | All as per item No.1 above but 30 HP to 40 HP capacity | 5 | Each Job | |
| 4 | 4 | M&L for repair and overhauling of submersible pump set of capacity 5 to 10 HP by opening/de-assembling the pump including degusting, de-scaling, servicing, oiling/greasing & including replacement of worn out defective spare parts as GI washer, nuts, bolts, packing and other minor parts not specifically mentioned shall be replaced where required for proper functioning of pump set including re-assembling in the existing position, testing complete all as specified and directed. Note:- The unit ratre quoted is deemed to be inclusive of washers, studs & nuts, nut & bolts, impeller key, packing materials and other minor spare parts upto Rs.200/-/Each.(ii) Major spare parts will be measured and paid separately. \n | 1 | Each Job | |
| 5 | 5 | All as per item No.4 above but 15 to 20 HP capacity | 2 | Each Job | |
| 6 | 6 | All as per item No.4 above but 30 HP to 40 HP capacity | 4 | Each Job | |
| 7 | 7 | Development of tube well by means of pumping high velocity 250 to 400 psi air compressor all as specified including arrangement for equipment fitting and supply of sodium hepta sulphate 20 kg all as specified for the bore wells located at various pump houses all as directed by Engineer-in-Charge.\nNote :- The unit rarte quoted is deemed to be inclusive of arrangement of suitable dia and length of PVC/canvas pipes to drain out the pumped water into the nearest drainage and to ensure no stagation of water nar the installation. | 4 | Each | |
| 8 | 8 | Supply only non-return valve suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 1 | Each | |
| 9 | 9 | Supply only CI Bowl body suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 10 | 10 | Supply only Stage sleeve for S/S in stage bowl suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 11 | 11 | Supply only Bearing bush in stage bowl suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 12 | 12 | Supply only Gun Metal impeller suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 13 | 13 | Supply only Pump motor connector CI suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 1 | Each | |
| 14 | 14 | Supply only Gun Metal neck ring suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 15 | 15 | Supply only Pump shaft stainless steel suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 2 | Each | |
| 16 | 16 | Supply only Coupling with key suitable for 5 to 10 HP pump for fixing under Sl No. 4 herein-before. | 1 | Each | |
| 17 | 17 | Supply only non-return valve suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 1 | Each | |
| 18 | 18 | Supply only CI Bowl body suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 4 | Each | |
| 19 | 19 | Supply only Stage sleeve for S/S in stage bowl suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 4 | Each | |
| 20 | 20 | Supply only Bearing bush in stage bowl suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 4 | Each | |
| 21 | 21 | Supply only Gun Metal impeller suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 1 | Each | |
| 22 | 22 | Supply only Pump motor connector CI suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 1 | Each | |
| 23 | 23 | Supply only Gun Metal neck ring suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 4 | Each | |
| 24 | 24 | Supply only Pump shaft stainless steel suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 1 | Each | |
| 25 | 25 | Supply only Coupling with key suitable for 15 to 20 HP pump for fixing under Sl No. 5 herein-before. | 1 | Each | |
| 26 | 26 | Supply only non-return valve suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 4 | Each | |
| 27 | 27 | Supply only CI Bowl body suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 4 | Each | |
| 28 | 28 | Supply only Stage sleeve for S/S in stage bowl suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 12 | Each | |
| 29 | 29 | Supply only Bearing bush in stage bowl suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 12 | Each | |
| 30 | 30 | Supply only Gun Metal impeller suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 12 | Each | |
| 31 | 31 | Supply only Pump motor connector CI suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 4 | Each | |
| 32 | 32 | Supply only Gun Metal neck ring suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 12 | Each | |
| 33 | 33 | Supply only Pump shaft stainless steel suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 4 | Each | |
| 34 | 34 | Supply only Coupling with key suitable for 30 to 40 HP pump for fixing under Sl No. 6 herein-before. | 4 | Each | |
| 35 | 35 | S&F in replacement of stator set of submersible motor for 30 HP duly winded with PVC insulated wire complete all as specifed and directed.\nMake: KSB/ SU/ Kalama | 1 | Each | |
| 36 | 36 | S&F in replacement of rotor for submersible motor submersible motor suitable for 30 HP rotor complete all as specified and directed. \nMake: KSB/ SU/ Kalama | 1 | Each | |
| 37 | 37 | M&L for rewinding of electric motor of submersible pump any make 3 phase, 415V, 5 to 10 HP capacity with PVC insulated heavy duty superior quality copper winding wires of suitable gauge/size matching to existing, straightening and replacement of unserviceable spares, cleaning of stator slots properly by using adequate size of sand paper including insulating materials complete all as specified and directed.\nNote:- The unit ratre quoted is deemed to be inclusive of washers, studs & nuts, nut & bolts, packing materials and other minor spare parts upto Rs.200/-/Each. | 1 | Each Job | |
| 38 | 38 | All as per item No.37 Above but 15 to 20 HP capacity | 1 | Each Job | |
| 39 | 39 | All as per item No.37 Above but 30 HP capacity | 4 | Each Job | |
| 40 | 40 | All as per item No.37 Above but 40 HP capacity | 1 | Each Job | |
| 41 | 41 | S&F in replacement of Thrust plate suitable for motor of capacity 5 to 10 HP complete all as specified and directed by Engineer-in-Charge | 2 | Each | |
| 42 | 42 | S&F in replacement of Segment bearing complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 43 | 43 | S&F in replacement of Segment housing body CI complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 44 | 44 | S&F in replacement of Lower bush body complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 45 | 45 | S&F in replacement of Upper bush body complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 46 | 46 | S&F in replacement of Pump connector CI complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 2 | Each | |
| 47 | 47 | S&F in replacement of Upper bearing body complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 48 | 48 | S&F in replacement of Lower bearing body complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 49 | 49 | S&F in replacement of S/S sleeve for rotar shaft complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 50 | 50 | S&F in replacement of Gunmetal bush for suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 4 | Each | |
| 51 | 51 | S&F in replacement of Sand guard complete set suitable for motor of capacity 5 to 10 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 52 | 52 | S&F in replacement of Thrust plate suitable for motor of capacity 10 to 20 HP complete all as specified and directed by Engineer-in-Charge | 1 | Each | |
| 53 | 53 | S&F in replacement of Segment bearing complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 54 | 54 | S&F in replacement of Segment housing body CI complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 55 | 55 | S&F in replacement of Lower bush body complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 56 | 56 | S&F in replacement of Upper bush body complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 57 | 57 | S&F in replacement of Pump connector CI complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 58 | 58 | S&F in replacement of Upper bearing body complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 59 | 59 | S&F in replacement of Lower bearing body complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 60 | 60 | S&F in replacement of S/S sleeve for rotar shaft complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 61 | 61 | S&F in replacement of Gunmetal bush for suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 8 | Each | |
| 62 | 62 | S&F in replacement of Sand guard complete set suitable for motor of capacity 10 to 20 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 1 | Each | |
| 63 | 63 | S&F in replacement of Thrust plate suitable for motor of capacity 30 to 40 HP complete all as specified and directed by Engineer-in-Charge | 4 | Each | |
| 64 | 64 | S&F in replacement of Segment bearing complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 65 | 65 | S&F in replacement of Segment housing body CI complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 66 | 66 | S&F in replacement of Lower bush body complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 67 | 67 | S&F in replacement of Upper bush body complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 68 | 68 | S&F in replacement of Pump connector CI complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 69 | 69 | S&F in replacement of Upper bearing body complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 4 | Each | |
| 70 | 70 | S&F in replacement of Lower bearing body complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 3 | Each | |
| 71 | 71 | S&F in replacement of S/S sleeve for rotar shaft complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 4 | Each | |
| 72 | 72 | S&F in replacement of Gunmetal bush for suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 12 | Each | |
| 73 | 73 | S&F in replacement of Sand guard complete set suitable for motor of capacity 30 to 40 HP ( Make :Kirloskar/ KSB/ Crompton) complete all as specified and directed by Engineer-in-Charge. | 4 | Each | |
| 74 | 74 | M&L for disconnecting the booster pump of any size and capacity from site including servicing and repair the same by replacing coupling including nut & bolts, bearings, bushes, oil seals and reassembling and re-alignment, commissioning and testing complete all as specified and directed. | 10 | Each Job | |
| 75 | 75 | Taking out submersible pump set/ deep well jet pump set of capacity 1 HP to 3 HP single phase, any type from bore well/ deep well by disconnecting all electrical and mechanical connections including connected items of pump such as column pipes, cable complete for checking & repair of pump including lowering & reassembling the pump in the existing position by reconnecting after repair and inspection of pump complete all as specified and directed. | 10 | Each Job | |
| 76 | 76 | M&L for repair and overhauling of submersible pump set/ deep well jet pumping set of capacity 1 HP to 2 HP by opening/de-asembling the pump including derusting, descaling, servicing, oiling/ greasing & including replacement of worn out defective parts, required GI washer, nuts, bolts and other minor parts not specifically mentioned shall be replaced where required for proper functioning of pump set complete all as specified and directed.\nNote:- The unit ratre quoted is deemed to be inclusive of washers, studs & nuts, nut & bolts, impeller key, packing materials and other minor spare parts upto Rs.200/-/Each. | 3 | Each | |
| 77 | 77 | M&L for rewinding of electric motor 3 phase, 415 Volts, 50 C/S, of capacity 2 HP to 10 HP of booster pump of any make from the pumping set, rewinding the stator coil with PVC insulated/super enamelled copper winding wire of existing type, guage and size including insulating material and reassembling and refixing in the same position with true alignment, testing and commissioning complete all as specified and directed. | 50 | Per HP | |
| 78 | 78 | M&L for rewinding of electric motor 3 phase, 415 Volts, 50 C/S, of capacity 2 HP to 3 HP of open well submersible pump of any make from the pumping set, rewinding the stator coil with PVC insulated copper winding wire of existing type, guage and size including insulating material and reassembling and refixing the same with true alignment, testing and commissioning complete all as specified and directed. | 46 | Per HP | |
| 79 | 79 | M&L for rewinding of electric motor of submersible pump any make and any type of capacity 1 HP with PVC insulated copper winding wire suitable gauge/size matching to existing straightening and repairing/ cleaning of stator slots properly by using adequate size of sand paper including insulating materials complete all as specified and directed. | 3 | Each Job | |
| 80 | 80 | S&F in replacement of Mild Steel column pipe flanged both ends 150 mm dia complete with necessary fixing arrangement such as suitable size of nuts, bolts, gasket, washer, etc complete 3 mtr long and 6 mm thick complete all as specified and directed. Make - Jindal/ Swastik/ Tata/ Prakash. | 2 | Each | |
| 81 | 81 | All as per item No. 80 here-in-before but 125mm dia. Make - Jindal/ Swastik/ Tata/ Prakash. | 2 | Each | |
| 82 | 82 | All as per item No. 80 here-in-before but 100mm dia Make - Jindal/ Swastik/ Tata/ Prakash. | 4 | Each | |
| 83 | 83 | S&F in replacement of PVC insulated flat copper submersible cable heavy duty 3 core 2.5 Sqmm 1100 volt grade of the following size complete all as specified and directed.\n Make: - Havells/ Plaza/ Finolex/Polycab | 30 | RM | |
| 84 | 84 | All as per item No.83 above but 3 core 16 Sqmm cable1100 volt grade | 200 | RM | |
| 85 | 85 | S&F in replacement MCCB 4 Pole, 200 Amps, Thermal release 160-200, 36 KA 415 volt grade complete and connecting with pump controller panel complete all as specified and directed. \nMake Cat part No CM98065OONO of L&T or equivalent in Legrand/Havells/Indoasian | 4 | Each | |
| 86 | 86 | S&F in replacement of single phase preventer SPPR type SDz5, 380V, suitable for MU-G30/40/50/75 complete all as specified and directed. \nMake Cat part No XM81807OOOO of L&T or equivalent in Legrand/Havells/Indoasian | 3 | Each | |
| 87 | 87 | S&F in replacement of ML-1.5 Thermal over load relay 10-16 Amps range complete all as specified and directed. Make Cat part No. SS91858OOBO of Make L&T equivalent in Legrand/Havells/Indoasian | 2 | Each | |
| 88 | 88 | S&F in replacement of ML-1.5 Thermal over load relay 28-42 Amps range complete all as specified and directed. Make Cat part No. SS91859OOFO of Make L&T equivalent in Legrand/Havells/Indoasian | 1 | Each | |
| 89 | 89 | S&F in replacement of ML-1.5 Contactor Kit for power contactor complete all as specified and directed. Make : Cat part No. SS95305 of L&T or equivalent in Legrand/Havells/Indoasian\n | 2 | Each | |
| 90 | 90 | S&F in replacement of ML-3 Contactor Kit for power contactor complete all as specified and directed. Make: Cat part No. SS95309 of Make L&T or equivalent in Legrand | 2 | Each | |
| 91 | 91 | S&F in replacement of ML-4 Contact Kit for power contactor complete all as specified and directed. Make Cat part No. SS95311 of Make L&T or equivalent in Legrand | 2 | Each | |
| 92 | 92 | S&F in replacement of Coil for ML-1.5 Contactor complete all as specified and directed. Make Cat part No. SS90873 of Make L&T or equivalent in Legrand | 3 | Each | |
| 93 | 93 | S&F in replacement of Coil for ML-3 Power Contactor complete all as specified and directed. Make Cat part No. SS90545 of Make L&T or equivalent in Legrand | 3 | Each | |
| 94 | 94 | S&F in replacement of Coil for ML-4 Power Contactor complete all as specified and directed. Make Cat part No. SS91258 of Make L&T or equivalent in Legrand | 2 | Each | |
| 95 | 95 | S&F in replacement of Contactor ML-3 Power Contactor complete all as specified and directed. Make Cat part No. SS90721 of Make L&T or equivalent in Legrand | 2 | Each | |
| 96 | 96 | S&F in replacement of contactor ML-4 Power Contactor complete all as specified and directed. Make Cat part No. SS90910 of Make L&T or equivalent in Legrand | 2 | Each | |
| 97 | 97 | S&F in replacement of MCB TP range 32 Amp, C curve, 10 kA complete all as specified and directed. Make : L&T/Havells/Legrand/Indoasian | 2 | Each | |
| 98 | 98 | S&F in replacement of MCB TPN range 40 Amp, C curve, 10 kA complete all as specified and directed.Make : L&T/Havells/Legrand/Indoasian | 2 | Each | |
| 99 | 99 | S&F in replacement of enclosure box 2 way/ 3 way/ 4 way complete all as specified and directed. Make : L&T/Havells/Legrand/Indoasian | 2 | Each | |
| 100 | 100 | S&F in replacement of submersible pump controller in sheet enclosure Type MR-G2 with MU-2P contractor & MU 2P relay for single phase motor 230 volts, 50 HZ, 3 phase, 1 HP, 0.75 KW, 9 -14 Amps relay range including suitable size LT panel, outdoor type, for mounting/fixing the pump controller, cubical compartmentalised of 2mm thick CRCA sheet powder coated front door openable with angle iron 45x45x5 mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type C1 (Using 20 mm graded stone aggregate) thimbling and cable entry boxes with cable gland inculding painting with two coat of powder coated painting over a coat of red oxide primer complete all specified and directed.\nMake Cat Part No. SS96560 of L&T or equivalent in Legrand/Havells/Indoasian/ABB/C&S | 1 | Each | |
| 101 | 101 | S&F in replacement of submersible pump controller in sheet enclosure Type MR-G6 DOL (With wideband Coil) for three phase motor 415 volts, 50 HZ, 3 phase, 5 HP, 6-10 Amps relay range including suitable size LT panel, outdoor type, for mounting/fixing the pump controller, cubical compartmentalised of 2mm thick CRCA sheet powder coated front door openable with angle iron 45x45x5 mm frame bottom of the panel board, grouted by using PCC foundation 1:2:4 type C1 (Using 20 mm graded stone aggregate) thimbling and cable entry boxes with cable gland inculding painting with two coats of powder coated painting over a coat of red oxide primer complete all specified and directed.\n Make Cat Part No. SS97756COVO of L&T or equivalent in Legrand/Havells/Indoasian/ABB/C&S | 3 | Each | |
| 102 | 102 | S&F in replacement submersible pump controller in sheet enclosure Type MU-G20 fully autimatic Star Delta Starter for single phase motor 415 volts, 50 HZ, 3 phase, 20 HP, 15 KW, 28-42 Amps relay range complete all specified and directed.\nCat Part No. SS95975 of Make L&T or equivalent in Legrand/Havells/Indoasian/ABB/C&S | 1 | Each | |
| 103 | 103 | S&F in replacement of PVC insulated with 2.5 sq mm 4 core, FR PVC Round Sheathed, Copper Conductor (flexible) industrial cable, 1100 Volt, conforming to IS 694 complete all specified and directed. | 150 | RM | |
| 104 | 104 | S&F in replacement of Pressure pump of capacity 1HP, single phase complete with air tanks, pressure control switch, pressure guage, brass assembly etc with all necessaray connection complete all as specified and as directed.\n Make: KSB/ Kirloskar/Crompton | 1 | Each | |
| 105 | 105 | S&F in replacement of Submersible pump of capacity 1 HP, single phase complete etc with all necessaray connection complete all as specified and as directed.\nMake: Kirloskar/ KSB/ Crompton | 1 | Each | |
| 106 | 106 | M&L for rewinding of pressure pump 0.5 HP to 1 HP of any make, single phase, 240V with PVC insulated heavy duty superior quality copper winding wires of suitable gauge/size matching to existing, straightening and replacement of unserveciable spares cleaning winding slots properly by using adequate size of sand paper including insulating materials complete all as specified and directed. \nNote: The unit rate quoted is deemed to be inclusive of cost of spares upto Rs. 200/-/Each. (ii) Cost of spares more than Rs.200/-/Each will be measured and paid separately under relevant items of Sch 'A'. | 5 | Job | |
| 107 | 107 | S&F in replacement Pressure switch suitable for pressure pump 0.5 to 1HP complete all as specified and directed. | 3 | Each | |
| 108 | 108 | S&F in replacement oil seal set suitable for pressure pump 0.5 to 1HP complete all as specified and directed. | 5 | Each | |
| 109 | 109 | S&F in replacement Ball bearing (set of two) suitable for pressure pump 0.5 to 1HP complete all as specified and directed. | 3 | Each Set | |
| 110 | 110 | S&F in replacement impeller suitable for pressure pump 0.5 to 1HP complete all as specified and directed. | 3 | Each | |
| 111 | 111 | Labour for Monthly checking and servicing of pressure pumps 0.5HP to 1HP, 230 Volts, 50Hz includes tightenen loose connection, nut bolts alongwith all other primary safety features for smooth functioning of pump complete all as specified and directed. Note:- 1. Checking of pressure pump on monthly basis shall be kept in written record also charges for same will be deemed to be included in unit rate quoted. 2. Complaints as received verbal/ telephonically for unserviceable pressure pumps shall be attended within 02 hours throughout the contract period and the defect shall be rectified with out any extra charges on this account. 3. Minor Spares cost upto Rs. 200/-/Each are deemed be included in the unit rate quoted. | 5 | Each Job | |
| 112 | 112 | Demolition of existing valve chamber and M&L for construction of brick masonry valve chamber 1050x1050x1050mm size with plain cement concrete in 1:4:8 type D2 foundation and 15mm thick plaster in CM 1:4 on brick wall inside and brick chamber built in cement mortar 1:6 including providing of MS Sheet cover 3mm thick with angle iron (40x40x6mm) brackets grouted to brick wall duly painted with two coats of synthetic enamel paint over a coat of red oxide primer with lifting handle and locking arrangement complete all as specified and as directed by the Engineer-in-Charge. | 2 | Each | |
| 113 | 113 | Dewatering the fountain, cleaning of fountain & fountain motor well complete, removing the algae, moss, roots, vines, clean out the cracks with wire brush, wash the concrete floor with acid, making the surface dust proof for filling the cracks with resin epoxy, cleaning the pipings, light fittings, nozzles for clearing the blokages, replacement of unserviceable wiring of water proof light fitting and spot light fittings, cutting removing or welding to MS/GI pipings for leak arresting as required at site, cutting removing the old unserviceable PVC fittings and replacement of PVC fittings with heavy duty ISI marked PPR pipe and fittings such as Tee, elbow, MTA, coupling , reducer, sockets of any size etc. painting to the MS & GI pipings inside the fountain with synthetic enamel paint of colours as directed after scrapping , scraching the existing suface and making good and disturbed surface with required PCC 1:2:4 type B1(Using 20 mm graded stone aggregate) filling up with water up to the desired level and testing and adjusting the nozzles for correct functioning complete all as specified and directed. \n Note : (i) PPR pipes and Cable for wiring as required will be measured and paid under relevent item of schedule.\n(ii) The above job will be operated as and when required at site for smooth functioning of the fountain during the entire period of contract for each fountain.\n(iii) Payment for this item shall be made on completion of the contract period. | 14 | Each Job | |
| 114 | 114 | S&F in replacement of vertical jet nozzle (ISI Marked) 40mm inlet dia and 80mm outlet opening made out of brass chromium plated.(as per sample) suitable for the fountain complete all as specified and directed. | 3 | Each | |
| 115 | 115 | S&F in replacement of adjustable type (ISI Marked) crown nozzle made of brass chromium plated complete all as specified and directed by Engineer-in-Charge. | 20 | Each | |
| 116 | 116 | S&F in replacement dandalion rod made out of aluminium alloy 60 cm long 12mm dia and cleaning and adjusting the nozzles (As per sample of ISI marked) complete all as specified and directed by Engineer-in-Charge. | 14 | Each | |
| 117 | 117 | S&F in replacement of water proof spot light LED light fittings 6x3watt power LED, input voltage 12V 18 watts, operating Temp 20-60 degree Centigrade, stainless steel body 304 with 6mm toughned glass , in multicolours of white- warm-yellow-green-blue, OD-180mm with U shape Clamp and multi colour RGB light effect with 3 Channel dimmer cord, protection IP-68 including flat steel brackets, steel pedastal, including required AC to DC converter/ driver etc complete all as specified and directed.Make : Aquarius Cat part No.AF-00140 or equivalent in Bajaj/Crompton/Havells/Philips | 4 | Each | |
| 118 | 118 | S&F in replacement of water proof/water tight light fitting 9x3watt power LED in put 9 V DC 27 watts, fully stainless steel 304 body, with 6mm PC glass in multicolours of white- warm-yellow-green-blue, protection IP-68 including required AC to DC converter/ driver etc complete all as specified and directed. Make : Aquarius Cat part No. AT-00117 or equivalent in Bajaj/Crompton/Havells/Philips | 4 | Each | |
| 119 | 119 | S&F in replacement of LED controller for fountain input 220volts output 12V DC, 5 Amp with on off switch push button for changing light 5 to 10 Nos LED light operator in belt PCB etc complete all as specified and directed. Make : Philips/Bajaj/Crompton/Havells | 4 | Each | |
| 120 | 120 | M&L for detecting the fault on LT panel/ submersible pump controller/ submersible pump/booster pumps sets etc, rectifying the defect on relays, metering devices, tightening the electrical accessories with required insulation materials, measuring and recording values of votage, ampere, earth resistance, checking of motor and pumps for its correct functioning etc taking out the old unserviceable wiring and cable in LT panel and replacing the wiring/cable with new one including requiredminor modification to the panel , cable gland, thimbles required for welding work etc based on day to day complaints complete all as specified and direceted by Engineer-in-Charge. \nNote: (i) The unit rate quoted is deemed to inclusive of minor spare parts upto Rs. 200/-/Each. (ii) Major spare will be paid separately under relevant items of Sch 'A'. | 50 | Each Job | |
| 121 | 121 | S&F Tullu pump of capacity 1 HP, single phase complete etc with all necessaray connections all as specified and as directed.\nMake: Kirloskar/ KSB/ Crompton | 1 | Each | |
| 122 | 122 | Note:- 1. The unit rates are deemed to be inclusive of detailing the main power/mechanic to check and rectify the fault in panels /motor/pumps through out the day during the entire period of contract.\n2. Repair to pump motor will be carried immediately on noticing the defect and to be re-installed to ensure water supply to the Station as directed by Engineer-in-Charge .\n3. All critical items/ spares such as relays, power contactors, starters etc catered to be kept ready for use during the contact period and to be executed as directed by Engineer-in-Charge as and when required. | |||
| 123 | 123 | Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payments to the contractor before handing over old material. |
AI Tender Summary
Tender Timeline
Oct 07, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedOct 19, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 20, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender