| 1 | 1 | DEMOLITION OF CONCRETE, RING BUND | | | |
|---|
| 2 | 1.01 | 60.1.2 : RING BUND Type II Putting up ring bund with earth fille gunny bags of top width 1.0m bottom width 2.0m height 2.0 m side and filling in between with earth to form ring bund and maintaining the same leak proof till the completion of the work and clearing the site by dismantling the bund after completion of the work.etc.complete. | BI01010001010000000000000515BI0100001114 | 50 | metre |
|---|
| 3 | 1.02 | 15.2.1 : Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | BI01010001010000000000000515BI0100001115 | 11.005 | cum |
|---|
| 4 | 2 | CENTERING AND SHUTTERING, CONCRETE | BI01010001010000000000000515BI0100001116 | | |
|---|
| 5 | 2.01 | 5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete | BI01010001010000000000000515BI0100001117 | 102.483 | sqm |
|---|
| 6 | 2.02 | 4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) | BI01010001010000000000000515BI0100001118 | 22.481 | cum |
|---|
| 7 | 2.03 | 5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) | BI01010001010000000000000515BI0100001119 | 25.272 | cum |
|---|
| 8 | 2.04 | 5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more | BI01010001010000000000000515BI0100001120 | 3032.64 | kilogram |
|---|
| 9 | 2.05 | 13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | BI01010001010000000000000515BI0100001121 | 87.889 | sqm |
|---|
| 10 | 3 | EMBEDDED PARTS | BI01010001010000000000000515BI0100001122 | | |
|---|
| 11 | 3.01 | 85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges | BI01010001010000000000000515BI0100001123 | 3297 | kg |
|---|
| 12 | 3.02 | 85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges | BI01010001010000000000000515BI0100001124 | 320.378 | kg |
|---|
| 13 | 3.03 | od37086/2018_2019/MH : Fabrication, erection and commissioning of STRUCTURAL MILD STEEL EMBEDDED PARTS for CANAL GATES | BI01010001010000000000000515BI0100001125 | 3617.38 | kg |
|---|
| 14 | 3.04 | od37101/2018_2019/MH : Fabrication, supply, erection and assembling in correct position and alignment by welding SS embedded parts in 304 L grade for canal gate as per directions of departmental officers at site including cost of materials, labour, hire charge of machinery, consumables, lead and lift, conveyance, incidental charges and handling etc. compete. | BI01010001010000000000000515BI0100001126 | 32.232 | kg |
|---|
| 15 | 3.05 | 85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site | BI01010001010000000000000515BI0100001127 | 97.341 | sqm |
|---|
| 16 | 4 | SUPPLY AND FABRICATION AND PAINTING OF MS SHUTTERS | BI01010001010000000000000515BI0100001128 | | |
|---|
| 17 | 4.01 | 85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges | BI01010001010000000000000515BI0100001129 | 5634.08 | kg |
|---|
| 18 | 4.02 | 85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges | BI01010001010000000000000515BI0100001130 | 1871.1 | kg |
|---|
| 19 | 4.03 | od37087/2018_2019/MH : Fabrication and supply of STRUCTURAL STEEL CANAL GATE and its accessories | BI01010001010000000000000515BI0100001131 | 7505.18 | kg |
|---|
| 20 | 4.04 | 85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site | BI01010001010000000000000515BI0100001132 | 203.996 | sqm |
|---|
| 21 | 5 | RUBBER SEAL | BI01010001010000000000000515BI0100001133 | | |
|---|
| 22 | 5.01 | 85.116 : Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing | BI01010001010000000000000515BI0100001134 | 21 | metre |
|---|
| 23 | 5.02 | 85.118 : Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings | BI01010001010000000000000515BI0100001135 | 42 | metre |
|---|
| 24 | 6 | ERECTION OF SHUTTERS | BI01010001010000000000000515BI0100001136 | | |
|---|
| 25 | 6.01 | od37088/2018_2019/MH : ERECTION of the CANAL GATE safely in the grooves | BI01010001010000000000000515BI0100001137 | 7505.18 | kg |
|---|
| 26 | 7 | HOIST BRIDGE AND MECHANISM | BI01010001010000000000000515BI0100001138 | | |
|---|
| 27 | 7.01 | 85.102 : Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges | BI01010001010000000000000515BI0100001139 | 2243.08 | kg |
|---|
| 28 | 7.02 | 85.101 : Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges | BI01010001010000000000000515BI0100001140 | 538.511 | kg |
|---|
| 29 | 7.03 | 85.107 : Supply of MS round bar including cost of conveyance charges | BI01010001010000000000000515BI0100001141 | 225.264 | kg |
|---|
| 30 | 7.04 | od37089/2018_2019/MH : Supply of BOLT and NUT up to 300mm Length including cost of conveyance. | BI01010001010000000000000515BI0100001142 | 24.416 | kg |
|---|
| 31 | 7.05 | od37090/2018_2019/MH : Providing EN-8 SQUARE THREADED SCREW ROD of dia 63mm (per metre rate) | BI01010001010000000000000515BI0100001143 | 28 | metre |
|---|
| 32 | 7.06 | od37091/2018_2019/MH : THREAD LESS portion of the screw rod (per metre rate) | BI01010001010000000000000515BI0100001144 | 3.5 | metre |
|---|
| 33 | 7.07 | od37092/2018_2019/MH : Supply and providing of worm and pinion having a lifting speed of around 5.00 cm/min for 24 rpm of<br>hand operation including cost of all materials, labour, hire charges and conveyance.(1 Nos worm and Pinion/shutter) | BI01010001010000000000000515BI0100001145 | 7 | each |
|---|
| 34 | 7.08 | od37096/2018_2019/MH : Fabrication and supply of HOISTING UNIT for CANAL GATE in structural steel | BI01010001010000000000000515BI0100001146 | 3006.86 | kg |
|---|
| 35 | 7.09 | 85.114 : Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site | BI01010001010000000000000515BI0100001147 | 79.012 | sqm |
|---|
| 36 | 7.1 | od37097/2018_2019/MH : ERECTION of the HOISTING UNIT and its ACCESSORIES | BI01010001010000000000000515BI0100001148 | 4163.97 | kg |
|---|
| 37 | 7.11 | od37093/2018_2019/MH : SUPPLYING and APPLYING GREASE on SCREW ROD for CANAL GATE | BI01010001010000000000000515BI0100001149 | 28 | metre |
|---|
