Work No . 212 Construction Of 04 Nos Bathroom Size 5 X 4 Each With Bricks Masonry Wall And Cgi Sheet Roofing And Glaze Tile In Floor And Wall Tiles
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Aug 2020
0 days left
EMD
10000
Bank guarantee accepted
Document Fee
200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Auction
Location / State
BCS ROUN UDHAMPUR → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Work No . 212 Construction Of 04 Nos Bathroom Size 5 X 4 Each With Bricks Masonry Wall And Cgi Sheet Roofing And Glaze Tile In Floor And Wall Tiles
BOQ
| Name of Work: <CONSTRUCTION OF 04 NOS BATHROOM SIZE 5 X 4 EACH WITH BRICKS MASONRY WALL AND CGI SHEET ROOFING AND GLAZE TILE IN FLOOR AND WALL TILES AT ROUN UDHAMPUR> | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Quantity | Units | Estimated Rate inRs. P | |
| 1 | 1.01 | CONSTRUCTION OF 04 NOS BATHROOM SIZE 5 X 4 EACH WITH BRICKS MASONRY WALL AND CGI SHEET ROOFING AND GLAZE TILE IN FLOOR AND WALL TILES AT ROUN UDHAMPUR | 0 | 0 | |
| 2 | 1.2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil | 13.24 | CUM | |
| 3 | 1.3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:5:10 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) | 2.26 | CUM | |
| 4 | 1.4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:5:10 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) | 11.55 | CUM | |
| 5 | 1.5 | Providing and laying stone boulders of size range 5 cm to 20 cm, in recharge pit, foundations etc. in the required thickness, all complete as per direction of Engineer-in-charge. | 4.08 | CUM | |
| 6 | 1.6 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | 8.45 | CUM | |
| 7 | 1.7 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete | 70.55 | SQM | |
| 8 | 1.8 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) | 14.95 | CUM | |
| 9 | 1.9 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Rectangular hallow pipe size(50x30x2.5)mm. | 146 | KG | |
| 10 | 2 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m² | 29.45 | SQM | |
| 11 | 2.1 | 12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand 1:6 (1 cement: 6 fine sand | 125.68 | SQM | |
| 12 | 2.2 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement prime | 32.31 | SQM | |
| 13 | 2.3 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | 53.88 | SQM | |
| 14 | 2.4 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete | 14.09 | SQM | |
| 15 | 2.5 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete. | 39.49 | SQM | |
| 16 | 2.6 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x 300 mm with single 15mm C.P. brass pillar tap | 2 | NO | |
| 17 | 2.7 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | 1000 | LTR | |
| 18 | 2.8 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. angle size(50x30x2.5)mm. | 180 | KG | |
| 19 | 2.9 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete | 2 | NO | |
| 20 | 3 | Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 165 mm long, weighing not less than 110 gms | 7 | NO | |
| 21 | 3.1 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.120 mm nominal bore, 120 mm long, weighing not less than 198 gms | 3 | NO | |
| 22 | 3.2 | Providing and fixing PTMT stop cock of approved quality and colour.20 mm nominal bore, 89 mm long, weighing not less than 88 gms | 2 | NO | |
| 23 | 3.3 | Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia with 25 mm waste hole | 1 | NO | |
| 24 | 3.4 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge. | 17.68 | MTR | |
| 25 | 3.5 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.30 mm thick pre laminated PVC door shutters | 5.57 | SQM | |
| 26 | 3.6 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. | 0 | 0 | |
| 27 | 3.7 | 15 mm nominal outer dia Pipes | 8 | MTR | |
| 28 | 3.8 | 20 mm nominal outer dia Pipes | 10 | MTR | |
| 29 | 3.9 | Providing and fixing unplasticised P.V.C. pipe with PTMT bends ,joints, t-bend, collar and bush of approved quality and colour and making good the walls all complete as per direction of Engineer in Charge. | 0 | 0 | |
| 30 | 4 | 100 mm nominal outer dia Pipes | 15 | MTR | |
| 31 | 4.1 | 150 mm nominal outer dia Pipes | 8 | MTR | |
| 32 | 4.2 | Providing and fixing Union in PVC. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :20 mm nominal bore | 4 | NO |
AI Tender Summary
Tender Timeline
Aug 10, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedAug 26, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 27, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender