Indian Army-IA has published Provision Of 04 X Amn Shed For 2 (I) Armd Bde. Submission Date for this Tender is 30-07-2020. Coats and Jackets Tenders in Janglote, Jammu and Kashmir and Sujanpur, Punjab Punjab. Bidders can get complete Tender details and download the document.
| Name of Work : Provn of 04 x Amn Shed for 2 (I) Armd Bde | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Provn of 04 x Amn Shed for 2 (I) Armd Bde. Scope of Work :- : The work consists of manufacture and supply of pre fabricated Amn Shed of over all size of 16000 x 6000mm with lightning conductor as per Sketch 'P' & Sketch 'Q' of RFP. The manufacturer shall supply detailed list of components that go to complete the making of the Shed as per RFP. The clear height of the Shed willl be 4.32m from floor finished level. All parts required for the manufacture of Shed shall be new and shall comply to relevant Bureau of Indian Standard specification and bear the mark as mentioned in RFP. All fabricated materials for purlin, truss, door and ventilator frames will be ISI mark with good finish and material of standard size. A ramp of slope 1:4 as shown as the sketch 'P' will be provided in front of the Shed. Minor addition/ alteration changes will be at the direction of Engineer executive of 421 (I) Engr Sqn and will be carried out without any additional cost at the time of execution. Shed shall be designed to cater for the following conditions :- (a) Sesmic co-efficient as per cesmis Zone V (b) Wind Load - Equivalent wind speed of 55 mtr per sec (IS-87) (c) Roof slope-30 Constr Material for 01 x Amn Shed :- (i) Ventilators as per RFP - 10 Nos (Make : TATA/SAIL/JINDAL) (ii) Doors as per RFP - 04 Nos (Make : TATA/SAIL/JINDAL) (iii) Truss as per RFP - 06 Nos (Make : TATA/SAIL/JINDAL) (iv) Purlin as per RFP - 54 Nos (Make : TATA/SAIL/JINDAL) (v) Main column as per RFP - 14 Nos (Make : TATA/SAIL/JINDAL) (vi) Column/lateral ties 04 Nos x 3.20 mtr long column RHS (Rectangular hollow section) of size 90x38x3.5 mm - 1560 Kgs (Make : TATA/SAIL/JINDAL) (vii) Wall cladding made of PPGI sheet as per RFP - 70 Nos (Make : TATA/SAIL/JINDAL) (viii) Roofing made of PPGI sheet as dper RFP - 53 Nos (Make : TATA/SAIL/JINDAL) (ix) PPGI sheet as per RFP for ridge coveer and gable end cover - 06 Nos (Make : TATA/SAIL/JINDAL) | 4 | Nos | |
| 2 | 2 | LIGHTNING CONDUCTOR. Lightning conductor shall be provided with aluminium rod of 12 mm dia 300 mm long. Aluminum down conductor (25 mm x 3 mm x 6m) GI earth plate of size 600mm x 600mm x 6mm CI Cover with frame (300mm x 300mm x 6mm), GI pipe light grade (20 mm dia x 1.3mm) long 3 mm perforations upto a length of 60 mm with MS funnel, GI strip, (32 mm x 6 mm x 4) GI pipe light grade 40 mm x 6mm, with base plate (300mm x 300mm x 8mm) and specials socked and plug 40 mm Clamps (20 mm x 3 mm) suitable for 40 mm dia pipe -06 Nos, bolts and nuts (6mm dia x 30mm) - 04 Nos Charcoal dust 50 kgs, Salt 50 kgs complete all as per IS 2309-1969. | Item 11 | 16 | Nos |
| 3 | 3 | Foundation, Flooring and Plinth Protection | |||
| 4 | 3.01 | Common building brick sub class 'B' of size 23cm x 11.5 cm conforming to IS 1077-1986. Average compressive strength not less than 15 N/mm2 | Item 12 | 17600 | Nos |
| 5 | 3.02 | Stone aggregate shall be crushed stone 40mm graded conforming to IS-383 - 1970 and shall be clean hard tough, durable and of uniform quality throughout. The aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities. | Item 13 | 76 | Cum |
| 6 | 3.03 | Stone aggregate shall be crushed stone n exc 63mm graded conforming to IS-383 - 1970 and shall be clean hard tough, durable and of uniform quality throughout. The aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities. | Item 14 | 52 | Cum |
| 7 | 3.04 | Ordinary Portland Cement grade 43, IS-12269-1990, packed in 50 kgs HDPE bags conforming to ISI 1652/2000. Make : ACC/Ambuja/JK Cement or Equivalent. | Item 15 | 556 | Bag |
| 8 | 3.05 | Stone aggregate shall be crushed stone 20mm graded conforming to IS-383 - 1970 and shall be clean hard tough, durable and of uniform quality throughout. The aggregate shall be free from soft disintegrated materials, vegetable and other organic impurities. | Item 16 | 32 | Cum |
| 9 | 3.06 | Expanded metal, cut to length, bend to shape required and tying with and including annealed mild steel wire not less than 0.9 mm dia or fixing with galvanized steel staples supplied and fix complete to steel members weight not less than 4 Kg per Sqm. | Item 17 | 81.2 | Sqm |
| 10 | 3.07 | Flat Iron 40 x 5mm | Item 18 | 40 | Kgs |
| 11 | 3.08 | Coarse Sand Sand shall be clean, sharp,angular hard and durable free from adherent coating and shall not contain clay, mica and other inpurities. The maximum quantities of clay and fine silt in sand shall not be more than 5% by mass as per IS-383-1970. | Item 19 | 64 | Cum |
| 12 | 3.09 | Water proofing compound confirming to IS-2645-1975, ISI marked, Make : Pidilite or Equivalent. | Item 20 | 80 | Kgs |
| 13 | 3.1 | Fire extnguisher 02 kgs capacity, ABC type MAP-90 alongwith its accessories confiming to IS 13849 \n(Make: Minimax, Firex, Ceasefire, ABB or Equivalent) | Item 21 | 8 | Nos |
| 14 | 3.11 | Wooden Planks 6' x 2' x 1" good quality & Sample to be approved by consignee. | Item 22 | 40 | Nos |
| 15 | 3.12 | Foundation Bolt 100 mm long made out of 12mm dia bar with two Nos washer. | Item 23 | 224 | Nos |
| 16 | 3.13 | Nut & Bolts 10mm dia 75mm long with washer for fixing together purlins and truss | Item 24 | 1728 | Nos |
| 17 | 3.14 | Self taping screw 2.5" long 8mm dia | Item 25 | 4000 | Nos |
| 18 | 4 | Erection Tools :- The following erection tools be provided alongwith the shelter. | |||
| 19 | 4.01 | Electric Hand Drill Machine (Heavy duty) capable of drilling hole in 6-10mm thickness MS plate. \nMake : Bosch/Hammer/Dewalt | Item 26 | 2 | Nos |
| 20 | 4.02 | Drill bits 8mm Heavy Duty \nMake : BOSCH/HARISSON/POWER TECH | Item 27 | 16 | Nos |
| 21 | 4.03 | Drill bits 6mm Heavy Duty Make : BOSCH/HARISSON/POWER TECH | Item 28 | 16 | Nos |
| 22 | 4.04 | Drill bits 9/64" in Packet of 10 Nos \nMake : BOSCH/HARISSON/POWER TECH | Item 29 | 4 | Nos |
| 23 | 4.05 | Drill bits 1/8" in Packet of 10 Nos\nMake : BOSCH/HARISSON/POWER TECH | Item 30 | 4 | Nos |
| 24 | 4.06 | Double ended spanner 16x17 \nMake : BOSCH/HARISSON/POWER TECH | Item 31 | 4 | Nos |
| 25 | 4.07 | Double ended spanner 20x22\nMake : BOSCH/HARISSON/POWER TECH | Item 32 | 4 | Nos |
| 26 | 4.08 | Adjustable spanner 12" \nMake : BOSCH/HARISSON/POWER TECH | Item 33 | 2 | Nos |
| 27 | 4.09 | Screw driver with insulated plastic handle 8" \nMake : TAPARIA/ESTMON/PIE | Item 34 | 2 | Nos |
| 28 | 4.1 | Screw driver with insulated plastic handle 15" \nMake : TAPARIA/ESTMON/PIE | Item 35 | 2 | Nos |
| 29 | 4.11 | Brick Hammer 200 gms with wooden handle \nMake : TAPARIA/ESTMON/PIE conforming to IS 4953/1973 | Item 36 | 4 | Nos |
| 30 | 4.12 | Hammer claw 700 gms with wooden handle \nMake : TAPARIA/ESTMON/PIE conforming to IS 4953/1973 | Item 37 | 4 | Nos |
| 31 | 4.13 | Insulated electric Plier 6" Conforming to IS 10353-1982 for Make : TAPARIA/ESTMON/PIE | Item 38 | 2 | Nos |
| 32 | 4.14 | Hand wood saw 18" Make : EAGLE/HIRA | Item 39 | 2 | Nos |
| 33 | 4.15 | Pipe Wrench 12" best quality as per directed. | Item 40 | 2 | Nos |
| 34 | 4.16 | Hack saw fram Make : EAGLE/HIRA | Item 41 | 2 | Nos |
| 35 | 4.17 | Hack saw blades both sides Make : Eagle/Hira | Item 42 | 48 | Nos |
| 36 | 4.18 | Bustard half round file 18" Bastered Make : EAGLE/HIRA | Item 43 | 2 | Nos |
| 37 | 4.19 | Round File 3/8" Make : EAGLE/HIRA | Item 44 | 2 | Nos |
| 38 | 4.2 | PGI Tool box of size 60 x 45 x 30cm complete set with lock (Make of lock : 7 levers 50mm Godrej Navtal with three keys) | Item 45 | 2 | Nos |
| 39 | 4.21 | Silicon Gun | Item 46 | 2 | Nos |
| 40 | 4.22 | Silicon Tube | Item 47 | 12 | Nos |
| 41 | 4.23 | Bricks trowel steel 305 mm \nMake : TAPARIA/TATA | Item 48 | 4 | Nos |
| 42 | 4.24 | Ruber hand gloves superior quality | Item 49 | 16 | Prs |
| 43 | 4.25 | Showel square nose medium type fittd with storng steel crutched wooden handles | Item 50 | 2 | Nos |
| 44 | 4.26 | Pick axe with chisel and point ends (Kudali 14 CP) nominal weight 3.0 kg, overall length (minimum) 595 mm with handle | Item 51 | 2 | Nos |
| 45 | 4.27 | Galvanised iron Pan motar (Tasla) 18 gauge, 16" dia minium weight 01 Kg | Item 52 | 4 | Nos |
| 46 | 4.28 | Wooden plaster trowel with wooden handle ISI Marked | Item 53 | 4 | Nos |
| 47 | 4.29 | Water Bucket Steel 13" dia | Item 54 | 2 | Nos |
| 48 | 4.3 | Aluminium Plaster Rod 1.2m long best quality | Item 55 | 2 | Nos |
| 49 | 4.31 | Safety Harness complete sets | Item 56 | 4 | Nos |
| 50 | 4.32 | Plastic pipe for measuring water level | Item 57 | 100 | Mtr |
| 51 | 4.33 | Rammer earth | Item 58 | 4 | Nos |
| 52 | 4.34 | Measuring tape metallic 3 mtr long Make : Stanley/Freemans | Item 59 | 4 | Nos |
| 53 | 4.35 | Measuring tape 30 mtr long Make : Stanley/Freemans | Item 60 | 2 | Nos |
| 54 | 5 | Labours & Plants | |||
| 55 | 5.01 | Skilled Labour (02 Men Per Day) | Item 61 | 35 | Days |
| 56 | 5.02 | UnSkilled Labour (02 Men Per Day) | Item 62 | 35 | Days |
| 57 | 5.03 | Hiring of JCB for 4 hours per day (including fuel, oil & lubricants) | Item 63 | 15 | Days |
| 58 | 5.04 | Hiring of concrete mixer machine (including fuel, oil & lubricants) | Item 64 | 20 | Days |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
