Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 09-07-2020 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 16-07-2020 |
| NAME OF WORK: ADDITION/ALTERATION TO MHS OFFICE ON FIRST FLOOR AT NOORBHOY BUILDING, PROVISION OF ELECTRONIC METERS AT INS ANGRE, PROVISION OF CHIMNEY FOR WET CANTEEN AT INS ANGRE, ADDITION/ALTERATION TO SECURITY LIGHTS AT SITE II, III & V AT INS TRATA WORLI AND PROVISION OF TEMPORARY ACCOMMODATION FOR NESS JUNIOR SAILORS MESS AT SITE II, INS TRATA UNDER GE (NW) KUNJALI. | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15 cm thickness below or above Ground level complete all as specified and as directed. | 1 | Cum | |
| 2 | 2 | Demolition of cement concrete of any description and any position not otherwise specifically provided for complete all as specified and as directed. | 0.5 | Cum | |
| 3 | 3 | Taking down chowkats or frames not exceeding 1.5sqm with shutters (without taking off shutters from the frame) and disposing off complete as specified and as directed. | 6 | Each | |
| 4 | 4 | Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each with shutters (without taking off shutters from the frame) and disposing off complete as specified and as directed. | 8 | Each | |
| 5 | 5 | S&F 15 mm dia medium grade galvanized steel tubing with all fittings fixed to walls, ceilings or laid under floors including taking down old 15mm bore, GI tubing complete all as specified and as directed. | 45 | RM | |
| 6 | 6 | All as per Srl item No.5 herein before but 20mm dia . | 10 | RM | |
| 7 | 7 | Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed. | 15 | Sqm | |
| 8 | 8 | M&L for applying polythene film 50 micron thick laid on a coat of blown type bitumen of grade 85/25 at the rate of 1.50 Kg per sqm over a coat of bitumen primer @ 0.30 Kg per Sqm complete all as specified and as directed. | 8 | Sqm | |
| 9 | 9 | M&L for 100 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone agg as in sub base of floors complete all as specified and as directed. | 85 | Sqm | |
| 10 | 10 | M&L for 25 mm thick cement concrete type B-1 1:2:4 (20 mm graded stone agg) as in floor complete all as specified and as directed. | 25 | Sqm | |
| 11 | 11 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and as directed. | 35 | Sqm | |
| 12 | 12 | S&F GI (cold rolled) snap grid size of 600 mm x 600 mm frame work of 24x38x0.6mm Tee section (bottom pre-coated) and 24x24x5mm thick angle alongwith the wall incl suspenders as per manufacturer instruction as in ceiling (Make- Gabson eternit/Everest or S&F of asbestos free calcium slicate designer boards 4 mm thick complete all as specified and as directed. | 35 | Sqm | |
| 13 | 13 | Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed. | 89 | Sqm | |
| 14 | 14 | M&L double charge premium quality virified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor including 20mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.\nNote : GE will select sample from latest catalouge of 2019-20. | 65 | Sqm | |
| 15 | 15 | M&L double charge premium quality vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36sqm (600x600mm),but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM1:3 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.\nNote : GE will select sample from latest catalouge of 2019-20. | 10 | Sqm | |
| 16 | 16 | M&L for coloured Glazed ceramic wall tiles,of size 450x300x 7mm thick of superior quality fixed on vertical surfaces such as skirting / dado / risers of step etc.,set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles fixed over & including backing coat of 15mm thick plaster in CM (1:4) complete all as specified and as directed\n | 60 | Sqm | |
| 17 | 17 | M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/Rectangular) area of each tiles exc 0.9 Sqm but not exc 0.18 sqm in floor including 15mm thick screed bed or bedding layer for laying floor finishes in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. | 20 | Sqm | |
| 18 | 18 | M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. | 9 | Sqm | |
| 19 | 19 | M&L for machine cut kota stone slab as in flooring 20 to 25mm thick riser of steps, skirting, dado and pillar laid over including 15 mm thcik rendering in CM 1:4 complete all as specified and as directed. | 60 | Sqm | |
| 20 | 20 | Rounding to edges of stone slabs one edge such as in steps, cooking platform and other similar situation complete all as specified and as directed. | 2 | RM | |
| 21 | 21 | Demolition of brickwork or stone boulder masonry, built in cement mortar including all quoins,arches, pillars, and precast concrete articles etc. complete all as specified and as directed. | 1 | Cum | |
| 22 | 22 | M & L brick work with sub class B bricks straight or curved on plan exc 6.00 mtrs mean radius built in CM 1: 6 complete all as specified and as directed. | 36 | Cum | |
| 23 | 23 | M&L for brick work with sub class 'B' bricks , straight or curved on plan to any radius in half brick thick wall built in cm 1:4 complete all as specified and as directed. | 5 | Sqm | |
| 24 | 24 | Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water , etc. complete all as specified and as directed. | 100 | Sqm | |
| 25 | 25 | M&L for rendering 15mm thick in CM 1:6 brick work or concrete surface and finishing the surface even and smooth complete all as specified and as directed. | 140 | Sqm | |
| 26 | 26 | Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified.\n(Water proofing compound to be measured and paid for separately). | 170 | Sqm | |
| 27 | 27 | S&F aluminium anodised various section as required for doors, window & partion etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant etc complete all as specified and as directed. | 2230 | Kg | |
| 28 | 28 | S&F aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 104 or equivatent 7.5 mm thick complete all as specified and as directed. | 31 | Sqm | |
| 29 | 29 | S&F 12mm thick, toughened glass for door shutters, partitions, shelves etc with and including fitting and fixtures such as glass handles SS studs, fittings for door pivots etc complete all as specified and as directed. | 10 | Sqm | |
| 30 | 30 | S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet used instead of plain colour PVC sheet (edges will be painted to match with prelam sheet) reinforced with MS square tube, suppling & fixing in opening as per specification. | 55 | RM | |
| 31 | 31 | S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 mm raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm prelam PVC sheet on back face supplying & fixing in frame at site as per specifications. | 20 | Sqm | |
| 32 | 32 | S&F 150 mm extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed. | 36 | Each | |
| 33 | 33 | S&F 150 mm long floor door stopper of aluminium ally body and tongue with hard drawn steel spring fixed on door shutter complete all as specified and as directed. | 10 | Each | |
| 34 | 34 | S&F 100 mm butt hinges medium weight cold rold mild steel and fixed complete all as specified and as directed. | 50 | Each | |
| 35 | 35 | S&F 2nd class HW small fittings such as brackets of any type latch and hinge blocks, shaped door and window stops and the like incl all necessary labours articles n.exc 200 cucm each complete all as specified and as directed. | 4 | Each | |
| 36 | 36 | S&F 200 mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed. | 26 | Each | |
| 37 | 37 | S&F 300 mm long aluminium ally anodised sliding door bolt with hasp and stape (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed. | 13 | Each | |
| 38 | 38 | M&L 4.80 mm thick Plain/Frosted sheet glass ordinary quality and glazing with oil putty or beads in square n.exc 0.5 sqm in each pane complete all as specified and as directed. | 28 | Sqm | |
| 39 | 39 | M&L for stainless steel wire cloth 0.36 mm nominal dia or wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. | 10 | Sqm | |
| 40 | 40 | S&F fancy type drapery rods, powder coated aluminium of 20-25mm size with fixing brackets, Knobs rollers etc.all as specified. | 20 | Rm | |
| 41 | 41 | M&L 18/19 mm thick prelaminated particle board, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in kitchen cabinet boxes complete all as specified and as directed. | 50 | Sqm | |
| 42 | 42 | Extra over rates of block board or venered particle board for external teak wood lipping 6 mm thick fixed with nails for 18/19 mm thick prelaminate boards complete all as specified and as directed. | 50 | RM | |
| 43 | 43 | S&F continous (piano hinges, mild steel, bright finish or electrogalvanised width of flaps (when opened) 40 mm complete all as specified and as directed. | 20 | RM | |
| 44 | 44 | S&F ball catches with 8 mm dia steel ball and brass body and striking plate incl letting in and fixed complete all as specified and as directed. | 10 | Each | |
| 45 | 45 | Cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting n.exc 10 cm girth pinning in making good to facings where required and pointing in CM 1:3 on stone walls complete all as specified and as directed. | 15 | RM | |
| 46 | 46 | S&F in repairs fancy type bib taps, chromium plated cast coper alloy 15 mm bore with crutch or butter fly handle, screwed down & fixed complete all as specified and as directed. | 7 | Each | |
| 47 | 47 | S&F in repairs CP pillar taps 15 mm dia cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. | 4 | Each | |
| 48 | 48 | S&F in repairs stop valve fancy type chromium plated screwed down with long shank and cup (concealed type) of 15 mm dia bore complete all as specified and as directed. | 53 | Each | |
| 49 | 49 | S&F in repairs chromium plated brass angle valve suitable for 15 mm bore pipe complete all as specified | 12 | Each | |
| 50 | 50 | S&F in repairs Vitreous China wash down water closet pan, white colour, fixing bolts, fixed in repairs including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. including seat cover complete. Excluding flushing cistern and flush pipe complete all as specified and as directed. | 6 | Each | |
| 51 | 51 | S&F in repairs vitreous china wash hand basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and CP brass waste coupling complete all as specified and as directed, | 4 | Each | |
| 52 | 52 | S&F in repairs PVC valveless syphonic action type ,flushing cistern Low level white, with inlet ball valve, float and handle 10 Ltr capacity including brackets complete all as specified and as directed. | 6 | Each | |
| 53 | 53 | S&F Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern complete all as specified and as directed. | 6 | Each | |
| 54 | 54 | S&F PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and as directed. | 16 | Each | |
| 55 | 55 | S&F PVC waste pipe 32 mm dia 800 mm long with socket suitablefor WHB/sink complete all as specified and as directed. | 6 | Each | |
| 56 | 56 | S&F 75 mm dia of out let cast iron floor trap with grating incl jointing to waste pipe in cement concrete type B-1 1:2:4 complete all as specified and as directed. | 10 | Each | |
| 57 | 57 | S&F in repairs looking mirror 600x450x5mm thick with aluminium channel frame, selected quality mounted on 6mm thick commercial ply wood back and fixed with chromium plated brass screwes and cup washers complete all as specified and as directed. | 7 | Each | |
| 58 | 58 | S&F in repairs tubular towel rail 600mm long 20mm dia brass chromium plated fixed with wooden guities embeded in cement mortar (1 : 3) with steel screws etc, complete all as specified. | 7 | Each | |
| 59 | 59 | S&F PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floor to 110 mm dia complete all as specified and as directed. | 10 | RM | |
| 60 | 60 | All as per Srl item No.59 herein before but 75 mm dia | 6 | RM | |
| 61 | 61 | S&F PVC (SWR) pipe single socketed in any length with rubber ring joints 110 mm dia fixed to walls with clamp complete all as specified and as directed. | 5 | RM | |
| 62 | 62 | All as per Srl item No.61 herein before but 75 mm dia | 10 | RM | |
| 63 | 63 | S&F PVC bends any radius 110 mm dia provided with access door complete all as specified and as directed. | 10 | Each | |
| 64 | 64 | All as per Srl item No.63 herein before but 75 mm dia | 5 | Each | |
| 65 | 65 | PVC (SWR) junction signle 'T' equal or unequal 110 mm dia provided with access door | 5 | Each | |
| 66 | 66 | All as per Srl item No.65 herein before but 75 mm dia | 5 | Each | |
| 67 | 67 | M&L RCC 1:2:4 (nominal mix) type B-1 using 20 mm graded stone agg as in landing, cooking platforms, shelves and the like complete all as specified and as directed. | 0.5 | Cum | |
| 68 | 68 | M&L RCC 1:2:4 (nominal mix) type B-1 using 20 mm graded stone agg as in chajjas complete all as specified and as directed. | 0.5 | Cum | |
| 69 | 69 | M&L for providing precast cement concrete (RCC) nominal mix 1:2:4 type B-1(using 20 mm graded stone agg) as in landings, cover slabs (for manholes etc) chullah hoods, chajjas water troughs mangers, shelves and similar articles with plain faces and setting in cement mortar 1:4 complete with joints to match incl necessary form work all as specified and as directed. | 0.5 | Cum | |
| 70 | 70 | M&L for RCC (design mix), M-30 in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. | 0.5 | Cum | |
| 71 | 71 | M&L for RCC (design mix), M-30 in beams, cantilevers, bressumers, lintels over 1.5 m span complete all as specified and as directed. | 1 | Cum | |
| 72 | 72 | Form work fair finished to sides and soffits of floor or roof beams, beam haunchings, girders,bresumers, lntels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc. complete all as specified and as directed. | 25 | Sqm | |
| 73 | 73 | Use and waste of formwork to soffits of suspended slabs, landings, shelves and similar work n.exc 200 mm thick horizontal or sloping complete all as specified and as directed. | 25 | Sqm | |
| 74 | 74 | M&L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and as directed. | 250 | Kg | |
| 75 | 75 | M&L mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified and as directed. | 165 | Kg | |
| 76 | 76 | M&L for preparation of newly wooden surfaes of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer incl preparation of surfaces complete all as specified and as directed. | 25 | Sqm | |
| 77 | 77 | M&L for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. | 50 | Sqm | |
| 78 | 78 | M&L for preparation of newly steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. | 60 | Sqm | |
| 79 | 79 | M&L for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. | 45 | Sqm | |
| 80 | 80 | M&L for preparation of newly plaseted surfaces of walls, chajjas, parapets, pilasters etc applying two coats of acrylic emulsion exterior weather proof paint (100% Acrylic) on external surfaces over a coat of primer complete all as per manufactures instruction all as specified and as directed. | 170 | Sqm | |
| 81 | 81 | M&L peparation of old surfaces of walls soffits, facia roof and applying one coat of weather proof acrylic based paint (100% acrylic) etc complete all as specified and as directed. | 60 | Sqm | |
| 82 | 82 | Complete removal of existing treatment on wall, soffits, facia roof and applying two coat of weather proof acrylic based paint 100% acrylic paint over a coat of cement based primer complete all as specified and directed. | 75 | Sqm | |
| 83 | 83 | Dismantling water tanks exc 250Ltr and n.exc 500.00 ltr capacity complete all as specified and as directed. | 2 | Each | |
| 84 | 84 | S&F rotational moulded polyethylene water storage tank of 1000 Ltr capacity (cylinderical type) hoisted and fixed in position incl 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm -210 grams) complete all as specified and as directed. | 1 | Each | |
| 85 | 85 | S&F rotational moulded polyethylene water storage loft tank of 375 Ltr capacity (cubical in shape close top) hoisted and fixed in position incl 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm -210 grams) complete all as specified and as directed. | 2 | Each | |
| 86 | 86 | Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of 1 to 2 mm thick wall care putty and primer incl preparation of surfaces complete all as specified and directed. | 140 | Sqm | |
| 87 | 87 | Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down and applying two coats of oil bound distemper over a coat 1 to 2 mm thick wall care putty (JK/Birla ) and primer incl preparatiomn of surfaces complete all as specified and directed. | 150 | Sqm | |
| 88 | 88 | Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks and similar work conforming to Fe 290 Gd E-165 all as specified . | 50 | Kgs | |
| 89 | 89 | Excavation trenches n.exc 1.50M deep and n.exc 1.50 M depth, for foundation, etc or for shafts well, and & getting out in hard/dense soil. | 25 | Cum | |
| 90 | 90 | M&L for PCC 1:2:4 type C2 ( using 40 mm graded aggregate) as in foundations, filling and mass concrete | 3 | Cum | |
| 91 | 91 | M&L for walling of random rubble, uncoursed, well bounded, bedded and solidly hearted, built in CM 1:4 all as specified and as directed | 20 | Cum | |
| 92 | 92 | M&L for flush pointing to random rubble masonry uncoursed or brought upto course in CM 1.4 complete all as specified and as directed. | 25 | 10 Sqm | |
| 93 | 93 | S&F Rolled mild steel in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angles, channel or flat sections) including distance pieces, cleats etc of Fe-410-W(Gde E-250) quality-A complete all as specified and as directed. | 1500 | Kg | |
| 94 | 94 | S&F of framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angels, as necessary, Gussets plates, riveting etc. n exc 10 Kg each brackets, conforming to Fe-290 Gde-E-165 complete all as specified and as directed. | 50 | Kg | |
| 95 | 95 | S&F Mild steel plated (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed. | 20 | Kg | |
| 96 | 96 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified | 80 | Sqm | |
| 97 | 97 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge of roof covering/cladding to wall, fixed with self tapping screws as specified | 10 | Sqm | |
| 98 | 98 | S&F for Everest ceiling made out of 600x600x15 mm thick classic lite PVC laminated mineral fibre acoustics ceiling board/tiles deep panel suspender system made out of GI sheet main Tee and cross tees and angle including 2mm GI wire for suspending, bolts, necessary washer, nut/ clits/ pin hook etc for securing frame work to ceiling to the snap grid complete all as specified and as directed. | 60 | Sqm | |
| 99 | 99 | M&L for 3mm thick wall care putty on plastered surfaces of internal wall etc complete all as specified and as directed. | 90 | Sqm | |
| 100 | 100 | Supply only integral waterproofing compound complete all as specified and as directed. | 40 | Kg | |
| 101 | 101 | Plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed of Second Class hard wood complete all as specified and as directed. | 0.3 | Cum | |
| 102 | 102 | S&F 35mm thick factory made 2nd class HW rail & stile plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed. | 12 | Sqm | |
| 103 | 103 | M&L for 2nd class hard wood glazed and skeleton shutters of 35 mm thick , open rebated and prepared to receive glass, gauze, etc. divided in to quares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.20 (a) ; supplied and fitted to chowkhats complete all as specified and as directed. | 8 | Sqm | |
| 104 | 104 | Cutting holes in brick walls in mud mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 depth of cutting exc half brick but n exc one brick all as specified. | 40 | Each | |
| 105 | 105 | M&L for MS flat for hold fast. Confirming to Fe-310-0 ro Fe-410-0 complete all as specified and as directed. | 25 | Kg | |
| 106 | 106 | S&F in repairs Soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and as directed. | 4 | Each | |
| 107 | 107 | S&F vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe) but including PVC waste pipe , providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement and fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern trap and waste pipe) fixed in repair complete all as specified. | 2 | Each | |
| 108 | 108 | M & L for 100mm thick PCC 1:2:4 type B-2, using 40mm graded stone aggregate as in path, hardstanding etc, finished even & smooth without using extra cement complete all as specified and as directed. | 20 | Sqm | |
| 109 | 109 | Surface dressing n exc 15 cm deep in hard/dense soil complete all as specified and as directed. | 10 | Sqm | |
| 110 | 110 | M&L hardcore of broken stones or boulders of gauge n.exc 63mm deposited,spread & levelled in layers 10cm thick, watered & rammed to a true surfaces complete all as specified and as directed. | 2 | Cum | |
| 111 | 111 | M&L for Machine pressed precast conctete interlocking paver block any shape and size gloosy finish coloured of approved design / pattern, confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade laid over and including fine sand cushion not less than 25 mm thick to a line surface, slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified and as per manufacturers instructions and directed. | 10 | Sqm | |
| 112 | 112 | S&F 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls | 15 | Rm | |
| 113 | 113 | S&F 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and as directed. | 20 | Rm | |
| 114 | 114 | S&F CI Bends100 mm bore (any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and as directed. | 6 | Each | |
| 115 | 115 | S&F CI Bends 75 mm bore ( any radius), diminishing pieces or tapers ( larger bore measured) complete all as specified and as directed. | 6 | Each | |
| 116 | 116 | M&L Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm complete all as specified and as directed. | 4 | Each | |
| 117 | 117 | M&L Cast iron nahani trap with grating including jointing to waste pipe run lead75 mm complete all as specified and as directed. | 4 | Each | |
| 118 | 118 | M&L for Branch pieces, 100 mm bore single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallei branches complete all as specified and as directed. | 3 | Each | |
| 119 | 119 | M&L for Branch pieces, 75 mm bore single ( equal or unequal), ordinary or inverted (spigot or socket type) or with parallei branches | 3 | Each | |
| 120 | 120 | S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm/100mm dia bore of pipe complete all as specified and as directed. | 20 | Each | |
| 121 | 121 | Returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm in hard/ dense soil complete all as specified and as directed. | 10 | Cum | |
| 122 | 122 | Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point outside from MD land complete all as specified and directed. | 15 | Cum | |
| 123 | 123 | Taking down carefully old U/S point wiring copper / Aluminum (light / fan / Sockets / power) complete with switches, sockets, fan regulators, ceiling roses, lamp holders, brackets, removing material form site and making good to disturbed surfaces complete all as specified and as directed. | 49 | Each | |
| 124 | 124 | Taking down old U/S MCB DBs complete with MCBs, isolator etc of any type and capacity from wall/ceiling etc & making good to the disturb surfaces complete all as specified and as directed. | 4 | Each | |
| 125 | 125 | M&L for point wiring with FRLS PVC insulated, un-sheathed, multi stranded copper conductor cable of 1.5sqmm size, 1100volts, drawn through and including non metalic rigid PVC casing and caping not less than 25mm with all accessories fixed on wall//ceiling/truss including FRLS PVC insulated, unsheathed, multi stranded copper conductor cable of 1.5sqmm size as earth continuty conductor connected to common earth dolly including required numbers and size of PVC modular box with cover plate in any size fixed on wall for fixing the switches, switch sockets, sockets, regulators etc complete all as specified for:- \nNOTE: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Electrical wiring above false ceiling shall be drawn through medium grade PVC conduit. | |||
| 126 | 125.1 | One light point controlled by one 5A switch | 54 | Per Point | |
| 127 | 125.2 | One Fan point controlled by one 5A switch | 26 | Per Point | |
| 128 | 125.3 | One 5A flush type switch socket point on same board board | 12 | Per Point | |
| 129 | 125.4 | One 5A flush type switch socket point on independent board | 15 | Per Point | |
| 130 | 126 | M&L for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate at required nos and size for One 5 pin, 15A switch socket combination on the independent board complete all as specified and directed. \nNote: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Switch socket measured & paid separately. | 15 | Per point | |
| 131 | 127 | M&L for point wiring complete with proper clour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate at required nos and size for 03 Nos 5 pin, 15A switch socket combination on the independent board complete all as specified and directed. \nNote: (a) Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza (c) Switch socket measured & paid separately. | 3 | Per point | |
| 132 | 128 | S & F modular switch 1 way 6A, 1 module complete all as specified and directed.\nMake: Anchor/Roma/Legrand. | 93 | Each | |
| 133 | 129 | S & F modular socket, 6A - 2/3 pin combined 2 modules complete all as specified and directed.\nMake: Anchor/Roma/Legrand. | 33 | Each | |
| 134 | 130 | S & F modular switch socket combination 6/16A, 2/3 pin, combined 2 module complete all as specified and directed.\nMake: Anchor/Roma/Legrand. | 18 | Each | |
| 135 | 131 | S&F for modular fan step regulator, 120W - 2 modular complete all as specified and directed.\nMake: Anchor/Roma plus/Legrand | 20 | Each | |
| 136 | 132 | S & F ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed. | 80 | Each | |
| 137 | 133 | Supply and fixing in repair Ultra slim edge lit type recess mounting LED 2X2 Luminaire 36 watt and extruded aluminium housing with anti-glare diffuser provides high quality ecomonic energy saving lighting LED Luminaire suitable for 600 x 600 mm modular/POP/Gypsum ceiling complete all as specified and as directed. \nMake: Crompton cat No LCPL-36-CDL(2X2) / C&S cat No LTCRSLM36WATT 2X2 or equivalent Cat part in Surya / Philips | 25 | Each | |
| 138 | 134 | S&F in repair of vertical type TPN DB 12 Way, 440 V with 250A Copper busbar, double door type, IP43- IK 09 protection suitable for housing MCB's all as specified and directed.\nMake: Legrand cat No 5077 33 or equivalent cat No. in Seimens/GE. | 3 | Each | |
| 139 | 135 | S&F in repair of vertical type VTPN DB 4 Way, 440 V with 200A busbar, double door type, IP43- IK 09 protection suitable for housing MCB's all as specified and directed.\nMake: Legrand cat No 5077 30 or equivalent cat No. in Seimens/GE. | 2 | Each | |
| 140 | 136 | S&F in repairs of MCCB sheet metal enclosure for holding MCCB of up to 160 Amps capacity four pole type including fixing accessories etc. complete all as specified and directed. \nMake: Legrand cat No 5078 01 or equivalent cat No. in Standard/GE/ Seimens/C&S | 1 | Each | |
| 141 | 137 | S & F MCB, SP, 63 Amps,10KA 'C' Curve 415 V complete all as specified and directed. \nMake: Legrand cat No 4085 98 or equivalent Cat part in Seimens/GE. | 6 | Each | |
| 142 | 138 | S & F MCB, TP, 63 Amps,10KA 'C' Curve 415 V complete all as specified and directed. \nMake: Legrand cat No 4086 61 or equivalent Cat part in Seimens/GE. | 3 | Each | |
| 143 | 139 | S & F MCB SPN 40 Amps,10KA 'C' Curve 240V complete all as specified and directed. \nMake: Legrand cat No 4086 18 or equivalent Cat part in Seimens/GE. | 3 | Each | |
| 144 | 140 | S & F MCB SPN 63 Amps,10KA 'C' Curve 240V complete all as specified and directed. \nMake: Legrand cat No 4086 20 or equivalent Cat part in Seimens/GE. | 3 | Each | |
| 145 | 141 | S & F MCB SP 6-32 Amps,10KA, 'C' series 240V complete all as specified and directed. \nMake : Legrand/Seimens/GE | 155 | Each | |
| 146 | 142 | M&L for sub-main wiring with 2 runs of 4.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit/casing caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed.\nNote: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza | 97 | RM | |
| 147 | 143 | M&L for sub-main wiring with 4 runs of 10.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit/casing caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 10.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed.\nNote: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza | 37 | RM | |
| 148 | 144 | M&L for sub-main wiring with 2 runs of 6.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade PVC conduit/casing caping not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including making good the distrubed surfaces/location complete all as specified and directed. \nNote: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster / Plaza | 24 | RM | |
| 149 | 145 | S & F Ceiling fan 5 Star Rated 1200 mm sweep heavy duty type complete with and suitable for operation on 230 Volts single phase 50 Hz AC supply and connectin up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection and fixed by completed all as specified and directed. \nMake: Havells/CG/ khaitan | 14 | Each | |
| 150 | 146 | S & F exhaust fan of sweep 300 mm heavy duty type complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230 Volts single phase 50 Hz AC supply and connectin up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection and fixed by using 4 Nos 200 mm long 12 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 completed all as specified and directed. \nMake: Havells/CG/ khaitan | 6 | Each | |
| 151 | 147 | Supply and fixing in repair new generation suspension mounted 2x18W LED pendant Luminaires and high translucent diffuser provides high quality ecomonic energy saving lighting incl suspension of 1.5mtr (set of 02 Nos) complete fixing arrangement all as specified and directed.\nMake :CG/Bajaj/C&S | 10 | Each | |
| 152 | 148 | S & F in repirs LED light fitting 20W, 230 V, 4 feet surface monted, indoor decorative aluminium extruded T-5 LED batten, integrated type etc., complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos including connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed. \nMake- C & S cat part No. LTTB4F20WLED/W (Nakshatra series) , or equivalent cat part in Crompton/Wipro /Philips | 10 | Each | |
| 153 | 149 | Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6.0sqmm 2 core laid in duct / along pole/wall tc including making connection complete all as directed. \nNote : 1. The cost of thimbles/lugs & cable gland etc is incl in quoted rate and no extra payment will be made for it. \nMake- Polycab/ Havells/ Finolex | 75 | RM | |
| 154 | 150 | Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10sqmm 2 core laid in duct / along pole/wall tc including making connection complete all as directed. \nNote : 1. The cost of thimbles/lugs & cable gland etc is incl in quoted rate and no extra payment will be made for it. \nMake- Polycab/ Havells/ Finolex | 140 | RM | |
| 155 | 151 | Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25sqmm 3½ core laid in duct / along pole/wall tc including making connection complete all as directed. \nNote : 1. The cost of thimbles/lugs & cable gland etc is incl in quoted rate and no extra payment will be made for it. \nMake- Polycab/ Havells/ Finolex | 320 | RM | |
| 156 | 152 | Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25sqmm 4 core laid in duct / along pole/wall etc including making connection complete all as directed. \nNote : 1. The cost of thimbles/lugs & cable gland etc is incl in quoted rate and no extra payment will be made for it. \nMake- Polycab/ Havells/ Finolex | 35 | RM | |
| 157 | 153 | Supply, fabrication, installation, testing & commissioning of LT Panel board / Feeder piller box, in door type, dust and vermin proof, made out of 2mm thick CRCA sheet, front openable doors having aluminium bus bar of capacity 100 amps for phases and 50 amps for neutral including powder coated painting, internal wiring with suitable size of stranded copper conductor cable, PCC foundation, supporting channels,cable termination,cable gland etc complete all as directed and suitable to accommodate the following switch gears and meters :-\na) MCCB 63Amps 4pole,36 KA,Thermal magnetic - 1 Nos (Incomer)\nb) MCCB, 3 pole 40 Amps,16KA,Thermal magnetic - 1 Nos (Out going)\nc) DOL starter for 2 HP 3 phase, 415V- 02 Nos\nd) Volt meter, digital type , 0 - 500V - 1 Nos\ne) Ammeter, digital type with CT's - 1 No\nf) indication lamps (R,Y,B) LED type - 1 set | 1 | Each Job | |
| 158 | 154 | S & F MCCB, 415 volts, 4 pole of capacity 100 Amps, 18 KA, ICS = 100% ICU, with fixed Thermal - Magnetic setting including spreader terminal/ thimble of suitable size and making connections complete all as directed. \nMake - Legrand cat No 4200 15 or equivalent Cat part in siemens/GE | 1 | Each | |
| 159 | 155 | S & F MCCB, 415 volts, 4 pole of capacity 100 Amps, 36 KA, ICS = 100% ICU, with fixed Thermal - Magnetic setting including spreader terminal/ thimble of suitable size and making connections complete all as directed. \nMake - Legrand cat No 4200 95 or equivalent Cat part in siemens/GE | 1 | Each | |
| 160 | 156 | S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. \nMake - Legrand cat No 5076 12 or equivalent Cat part in Siemens/GE | 3 | Each | |
| 161 | 157 | S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. \nMake - Legrand cat No 5076 11 or equivalent Cat part in Siemens/GE | 2 | Each | |
| 162 | 158 | S & F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. \nMake - Legrand cat No 5076 10 or equivalent Cat part in Siemens/GE | 1 | Each | |
| 163 | 159 | S & F in repair of Single pole and neutral enclosure with a two pin and Earth plug and socket complete with one single pole MCB 20A complete all as specified and directed. \nMake :Legrand cat No 5078 10 or equivalent cat No. in Seimens/GE/C&S | 2 | Each | |
| 164 | 160 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out completed all as specified and directed. | 54 | Cum | |
| 165 | 161 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm in hard/dense soils complete all as specified and directed. | 38 | Cum | |
| 166 | 162 | Removing excavated materials (Soils) exc 1.5 KM but not exc 5.00 KM and depositing outside from MD land complete all as specified and directed. | 38 | Cum | |
| 167 | 163 | M & L for fine dry sand filling in trenches as sand cushioning to cable 8 CM before laying of cables and 15 CM after laying cable which shall be puuned down to 10 CM completed all as specified and directed. \n(Note:- Only punned down 18 cm thickness shall be measured and paid) | 16.2 | Cum | |
| 168 | 164 | Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm completed all as specified and directed. | 1600 | Each | |
| 169 | 165 | Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level connected and incl galvanised earth lead wire 4.0mm dia by means of nuts & bolts, check nuts and wassher of galvinsed incl PCC (1:2:4) type B-1 cover reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25mm x 25mm x 3mm excavation and earth work in any type of soil, charcoal dust, salt light grade GI watering pipe 20mm dia with funnel and wire-mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distrubution board complete all to as shown in electrical plate No 3 of MES sch 2009 (part-I) connected main switch board all as specified and testing on completion . | 10 | Each Job | |
| 170 | 166 | Suppply and installaltion of single phase digital Meter AC Single phase Two wire, 50Hz static meter of class 1.0,High accuracy multifunctional, defect free, High surge resistant, Six months history of energy & MD in KW & KVA, Hackproof, Low power consumption, High insulation resistance (> 5 M ohms) & anti-tamper features( Phase-Nutral or Main & Load wire interchrged, Netural missing, DC Immunity, Abnormal Voltage Earth Load Tamper Indication etc)proof, 240V, 50Hz, 10-60A Make : L&T/Schneider/HPL | 3 | Each | |
| 171 | 167 | Supply and installation of three phases meter with the following specification : \n(a) AC three phase four wire, Tamper proof, static meter of class 1.0, 415V, 50Hz,10-60A anti-tamper features Display : High quality electromechanical LCD with one decimal multifunction CD display, KWH, Volt, PF load with battery \nMake : L&T/Secure/Schneider/Bentec/HPL | 5 | Each | |
| 172 | 168 | Refixing only ceiling fan in position same including making electric connection complete all as specified & directed | 6 | Each | |
| 173 | 169 | Supply and fixing copper tubings of appropriate dia for suction line and for liquid discharge line duly insulated with suitable insulation material including making hole in wall for passing though pipe and making good distrubed surface complete all as specified and as directed. | 20 | RM | |
| 174 | 170 | Disconnecting & taking down, strip opening, cleaning all parts and packing of ceiling fan of any make and size & greasing ball bearing with specified quilty grease and painting all as specified. | 6 | RM | |
| 175 | 171 | M & L for shifting of Split AC unit from existing postion & refixing the new position/location including general servicing as required, testing & commisssioning all including making good the distrubed surfaces/location complete all as specified and directed. | 2 | Each | |
| 176 | 172 | Supply & fix in replacement hot dip galvanized anti corroded weather proof octagonal electric poles 9 mtrs long top mounting on foundation complete with base plate and finial including PCC foundation as per manufacturer design with 1500 mm long Arms bracket,tapper plug, bolts nuts and screws etc as specified complete all as specified and directed including taking out existing detorated & unserviceable pole with street light bracket. | 27 | Each | |
| 177 | 173 | S &F in repair 90Watt, LED Bldg security light, PDC aluminium housing top maintainable with sealed toughened glass cover, SMD LED with secondary lens including connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed. \nMake- C & S cat part No. LTESST90WLED/LS, (Indus series), bajaj,cat part no- BRTFG 90W LED I V2 or equivalent cat part in Crompton / Wipro / Philips | 40 | Each | |
| 178 | 174 | S &F in repair LED Street light 48 Watt Energy Saving and Environment friendly light fitting with 24 nos LED Light source lumens with electronic gear housed in Pressure diecast alluminium alloy LM6 with IP65 protection operating volt up to 265 volts including suitable size of pipe bracket clamp for fixing complete all as specified and dierected .\nMake -Havells cat part No- ENDURACITYLINERNEXGENSL48WLED757SAYSBOPC. | 30 | Each | |
| 179 | 175 | S&F modular Switch 1 way 15 Amps, 1 module complete all as specified and directed.\nMake : Anchor/Roma/Legrand | 18 | Each | |
| 180 | 176 | S &F in repair LED Bldg Security Light 25 watt (INDUS-E SERIES) Power coated pressure die cast aluminium SMD LED Street Light with integraed lens complete all as specified directed.\nMake-Bajaj cat part No-BRLEP 25W LED WH, C&S Cat part No- LTESSE25WLED equivalent cat part in Crompton / Wipro / Philips | 19 | Each | |
| 181 | 177 | S &F in repair LED garden light 9 w cylindrical shaped integral decorative LED bollard with Opal acrylic diffuser and IP 65 With all acessories including PCC foundation tapper plug bolts, nuts, screwed etc complete all as specified and directed.\nMake -C&S cat Part No. LTGLCG9WLED or equivalent Cat part in Bajaj / Hevells / Crompton | 35 | Each | |
| 182 | 178 | S &F in repair 50Watt LED FLOOD: ORION -C SERIES COB LED flood light with pressure die cast aluminium, complete with all acessoriescomplete all as specified and directed.\nMake- Bajaj cat part No- BJFL 50 W LED, C&S CAT PART NO-LTEFC50WHPLED/W or equivalent Cat part in HAVELLs, wipro,CG | 10 | Each | |
| 183 | 179 | Supply and fix security search light fitting as per AJMERA (Marine seach light) weather proof chromium plated brass body,wheel house arrangements for both vertical and horizontal direction made out of brass sheet complete with heat resistant tougyhned glass with hot air escape arrangeemnt of cat part no 2573 with halogen lamp provided on security watch tower situted along the perimeter of sea wall and area all as specified and directed. | 3 | Each | |
| 184 | 180 | supply and fix Reflector for search light for 2000 watt cat part no 2573/r of Ajmera complete all as specified and directed. | 3 | Each | |
| 185 | 181 | S & F in Replacement MS arms bracket (best pattern) for mounting One in nos street light fitting including clamps/nut/bolts & washer to brace the same properly with duly in synthetic enamel paint of two coat in silver colour complete all as specified and directed. | 10 | Each | |
| 186 | 182 | S & F in Replacement MS arms bracket (best pattern) for mounting two in nos street light fitting including clamps/nut/bolts & washer to brace the same properly with duly in synthetic enamel paint of two coat in silver colour complete all as specified and directed. | 10 | Each | |
| 187 | 183 | S&F cable junction boxes IP 66/67 weather proof for out door installation(with knock outs cable entry junction box size should be 205x255x112 with terminals including complete all accessories specified and directed. \nMake -Hensel cat part no-KF2525 or equivalent Cat part in HAVELLs, wipro,CG | 50 | Each | |
| 188 | 184 | S&F 50 mm bore GI tubing light grade with all fittings like Tee, bend, elbow, MS clamps, nuts, bolts etc of 50 mm dia bore for cable protection on pole, road crossing or ground in pillars for fixing gate light etc complete all as specified and directed. | 30 | RM | |
| 189 | 185 | All as per Srl item No. 184 herein before but 32 mm bore | 60 | RM | |
| 190 | 186 | M&L fabrication of SS hood of gauge thick 304 grade steel hood size 48\"x30\"x18\" all as directed | 2 | Job | |
| 191 | 187 | M&L filter of size 24\"x24\"x2\" stainless steel material 304 grade all as directed. | 2 | Each | |
| 192 | 188 | M&L GI duct all as follows :- | |||
| 193 | 188.1 | (a) Common duct with two opening 40\"x24\"x18\" 22 gauge | 2 | Each | |
| 194 | 188.2 | (b) Two opening at the top face of thhe hood fitted pices 9\"x9\"x4\" (20 gauge) | 4 | Each job | |
| 195 | 188.3 | (c) Elbow with common duct connected with blower to sky end with top cover | 2 | Each | |
| 196 | 188.4 | (d) outside wall fitted duct connected with blower to sky end with top cover | 2 | Each | |
| 197 | 188.5 | (e) Canvas bag | 2 | Each | |
| 198 | 188.6 | (f) Exhaust duct coutlet of blower\nNote : Required Nos of Nut bolts, gasket, hanger Anchor bolt with assesaries 'C' clamp, 'U' clamp are included. | 2 | Each | |
| 199 | 189 | Supply installed and testing 2 HP motor , 3 phase, 1440 RPM inlet diameter 20\" x 20\" outlet diameter 24\" x 17\" inspection window will be provided on the casing which will facilated cleaning perposed without disturbing ducting drain play given at tie botton and drain out the dust partical/ slay etc all as directed. | 2 | Each | |
| 200 | 190 | M&L for centrifugal blower reststand (braket) fabrication of angle iron size 50x50x5mm thick frame are provided to blower resting stand etc all as directed | 2 | Each Job |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
