| 1 | 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. | item1 | 5 | Cum |
|---|
| 2 | 2 | Providing and laying in position cement concrete of PCC (1:5:10) grade excluding the cost of centering and shuttering in foundation upto plinth stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge in cement mortar | item2 | 1 | Cum |
|---|
| 3 | 3 | Supplying and filling in plinth with moorum under floors, including watering, ramming, consolidating and dressing complete. | item3 | 90 | Cum |
|---|
| 4 | 4 | Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge. | item4 | 3 | Cum |
|---|
| 5 | 5 | 12 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:6 (1 cement : 6 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. | item5 | 170 | Sqm |
|---|
| 6 | 6 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface | item6 | 3950 | Sqm |
|---|
| 7 | 7 | Finishing walls Two or more coats applied @ 3.84 kg/10 sqm) with water proofing cement paint of required shade. | item7 | 3950 | Sqm |
|---|
| 8 | 8 | Painting with synthetic enamel paint of approved brand and quality with two or more coats on new work over an under coat of suitable shade including all complete | item8 | 700 | Sqm |
|---|
| 9 | 9 | Renewing Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm), with putty and nails wherever necessary including racking out the old putty: | item9 | 12 | Sqm |
|---|
| 10 | 10 | Providing and fixing ISI marked flush door shutters 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: | item10 | 3.2 | Sqm |
|---|
| 11 | 11 | Providing and fixing factory made 30 mm thick plain PVC door shutters consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc.complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. | item11 | 3 | Sqm |
|---|
