Renovation Of Toilet Block Central Canteen College Campus At Jamia Millia Islamia .
Tender Value
5.83 Lakhs
Estimated cost
Bid Submission
01 Jun 2020
0 days left
EMD
11700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
MM Ali Jauhar Marg, JMI, New Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Renovation Of Toilet Block Central Canteen College Campus At Jamia Millia Islamia .
BOQ
| Name of Work: Renovation of Toilet Block Central Canteen College Campus at Jamia Millia Islamia. | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 2 | CIVIL WORK | |||
| 2 | 3 | CARRIAGE OF MATERIALS | |||
| 3 | 4 | By Mechanical Transport including loading,unloading and stacking_Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge.\r Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum or more. | Item1 | 5 | cum |
| 4 | 5 | EARTH WORK | |||
| 5 | 6 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge._All kinds of soil | Item2 | 2 | cum |
| 6 | 7 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m_All kinds of soil_Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia | Item3 | 20 | metre |
| 7 | 8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | Item4 | 2 | cum |
| 8 | 9 | CONCRETE WORK | |||
| 9 | 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :_1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). | Item5 | 2 | cum |
| 10 | 11 | 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled concrete aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size including Recycled concrete aggregate (RCA) upto 25%) | Item6 | 2 | cum |
| 11 | 12 | MASONRY WORK | |||
| 12 | 13 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in_Cement mortar 1:3 (1 cement : 3 coarse sand) | Item7 | 5 | sqm |
| 13 | 14 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level._Cement mortar 1:3 (1 cement :3 coarse sand) | Item8 | 10 | sqm |
| 14 | 15 | CLADDING WORK | |||
| 15 | 16 | Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth._Granite Stone of approved shade | Item9 | 3 | sqm |
| 16 | 17 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. | Item10 | 45 | sqm |
| 17 | 18 | WOOD AND PVC WORK | |||
| 18 | 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)._Second class teak wood | Item11 | 0.15 | cum |
| 19 | 20 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters._30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Item12 | 8.36 | sqm |
| 20 | 21 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). | Item13 | 8.36 | sqm |
| 21 | 22 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :_250x16 mm | Item14 | 8 | each |
| 22 | 23 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete _250x10 mm | Item15 | 8 | each |
| 23 | 24 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete _150x10 mm | Item16 | 16 | each |
| 24 | 25 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete_100 mm | Item17 | 8 | each |
| 25 | 26 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality._1.0 mm thick | Item18 | 16 | sqm |
| 26 | 27 | STEEL WORK | |||
| 27 | 28 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Item19 | 200 | kg |
| 28 | 29 | FLOORING | |||
| 29 | 30 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Item20 | 20 | sqm |
| 30 | 31 | FINISHING | |||
| 31 | 32 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :_New work (two or more coats) over and including water thinnable priming coat with cement primer | Item21 | 100 | sqm |
| 32 | 33 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade_Two or more coats on new work | Item22 | 50 | sqm |
| 33 | 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Item23 | 100 | sqm |
| 34 | 35 | REPAIRS TO BUILDING | |||
| 35 | 36 | Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge._Door chowkhats | Item24 | 5 | each |
| 36 | 37 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge. | Item25 | 4 | each |
| 37 | 38 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. | Item26 | 2 | each |
| 38 | 39 | Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. | Item27 | 20 | sqm |
| 39 | 40 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane_3 mm thick | Item28 | 5 | sqm |
| 40 | 41 | DISMANTLING AND DEMOLISHING | |||
| 41 | 42 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge._Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | Item29 | 2 | cum |
| 42 | 43 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead_Of area 3 sq. metres and below | Item30 | 5 | each |
| 43 | 44 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead._For thickness of tiles 10 mm to 25 mm | Item31 | 65 | sqm |
| 44 | 45 | Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge _15 mm to 40 mm nominal bore | Item32 | 150 | metre |
| 45 | 46 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. | Item33 | 4 | each |
| 46 | 47 | SANITARY INSTALLATIONS | |||
| 47 | 48 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:_White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Item34 | 2 | each |
| 48 | 49 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required_W.C. pan with ISI marked white solid plastic seat and lid | Item35 | 2 | each |
| 49 | 50 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required_Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern | Item36 | 2 | each |
| 50 | 51 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer | Item37 | 2 | each |
| 51 | 52 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete._Flexible pipe_32 mm dia | Item38 | 6 | each |
| 52 | 53 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Item39 | 2 | each |
| 53 | 54 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing_Rectangular shape 1500x450 mm | Item40 | 2 | each |
| 54 | 55 | Providing and fixing soil, waste and vent pipes_100 mm dia_Sand cast iron S&S pipe as per IS: 1729 | Item41 | 15 | metre |
| 55 | 56 | 75 mm diameter_Sand cast iron S&S pipe as per IS: 1729 | Item42 | 10 | metre |
| 56 | 57 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes_75 mm dia pipe | Item43 | 10 | each |
| 57 | 58 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes_100 mm dia pipe | Item44 | 10 | each |
| 58 | 59 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc._For 100 mm dia pipe | Item45 | 2 | each |
| 59 | 60 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc._For 75 mm dia pipe | Item46 | 2 | each |
| 60 | 61 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete._100 mm dia_Sand cast iron S&S as per IS - 1729 | Item47 | 3 | each |
| 61 | 62 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete._75 mm dia_Sand cast iron S&S as per IS - 1729 | Item48 | 3 | each |
| 62 | 63 | Providing and fixing plain bend of required degree._100 mm dia_Sand cast iron S&S as per IS - 1729 | Item49 | 2 | each |
| 63 | 64 | Providing and fixing plain bend of required degree.__75 mm dia_Sand cast iron S&S as per IS -1729 | Item50 | 2 | each |
| 64 | 65 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete._100x100x100 mm_Sand cast iron S&S as per IS - 1729 | Item51 | 2 | each |
| 65 | 66 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete._75x75x75 mm_Sand cast iron S&S as per IS - 1729 | Item52 | 2 | each |
| 66 | 67 | Providing and fixing single equal plain junction of required degree_100x100x100 mm_Sand cast iron S&S as per IS - 1729 | Item53 | 2 | each |
| 67 | 68 | Providing and fixing single equal plain junction of required degree_75x75x75 mm_Sand cast iron S&S as per IS - 1729 | Item54 | 2 | each |
| 68 | 69 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :_100 mm inlet and 100 mm outlet_Sand cast iron S&S as per IS: 3989 | Item55 | 4 | each |
| 69 | 70 | WATER SUPPLY | |||
| 70 | 71 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall_15 mm dia nominal bore | Item56 | 150 | metre |
| 71 | 72 | Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall_20 mm dia nominal bore | Item57 | 10 | metre |
| 72 | 73 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete_25 to 40 mm nominal bore | Item58 | 2 | each |
| 73 | 74 | Providing and fixing brass bib cock of approved quality_15 mm nominal bore | Item59 | 12 | each |
| 74 | 75 | Providing and fixing uplasticised PVC connection pipe with brass unions _45 cm length_15 mm nominal bore | Item60 | 10 | each |
| 75 | 76 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work_15 mm diameter pipe | Item61 | 150 | metre |
| 76 | 77 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work_20 mm diameter pipe | Item62 | 10 | metre |
| 77 | 78 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)_15 mm nominal bore | Item63 | 3 | each |
| 78 | 79 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)_20 mm nominal bore | Item64 | 2 | each |
| 79 | 80 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931_15mm nominal bore | Item65 | 12 | each |
| 80 | 81 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. | Item66 | 12 | each |
| 81 | 82 | Providing and fixing PTMT grating of approved quality and colour._Circular type_100 mm nominal dia | Item67 | 10 | each |
| 82 | 83 | DRAINAGE | |||
| 83 | 84 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete_150 mm diameter | Item68 | 20 | metre |
| 84 | 85 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design_150 mm diameter S.W. pipe | Item69 | 10 | metre |
| 85 | 86 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design_150 mm diameter S.W. pipe | Item70 | 10 | metre |
| 86 | 87 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design_100x100 mm size P type_With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Item71 | 2 | each |
| 87 | 88 | Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design_0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)_With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 | Item72 | 2 | each |
| 88 | 89 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete_For pipes 100 to 250 mm diameter | Item73 | 2 | each |
| 89 | 90 | Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Raising depth of manhole to be paid separately) _Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm of grade LD - 2.5 | Item74 | 2 | each |
| 90 | 91 | ELECTRICAL WORK | |||
| 91 | 92 | WIRING | |||
| 92 | 93 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet,suitable size M.S. box and earthing the point with 1.5 sq.mm.FRLS PVC insulated copper conductor single core cable etc. as required._Group C | Item90 | 16 | Point |
| 93 | 94 | Wiring for circuit / submain wiring along with earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface / recessed steel conduit as required._2 X 1.5 sq.mm + 1 X 1.5 sq.mm earth wire | Item91 | 40 | Mtr |
| 94 | 95 | Wiring for circuit / submain wiring along with earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface / recessed steel conduit as required._2 X 4 sq. mm + 1 X 4 sq. mm earth wire | Item92 | 20 | meter |
| 95 | 96 | Wiring for circuit / submain wiring along with earth wire with the following sizes of PVC insulated copper conductor, single core cable in surface / recessed steel conduit as required._2 X 16 sq. mm + 1 X 6 sq. mm earth wire | Item93 | 20 | meter |
| 96 | 97 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required._5/6 amps switch | Item94 | 18 | Each |
| 97 | 98 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required._15/16 amp switch | Item95 | 2 | Each |
| 98 | 99 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required._3 pin 5/6 amp socket outlet | Item96 | 2 | Each |
| 99 | 100 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required._6 pin 15/16 amp socket outlet | Item97 | 2 | Each |
| 100 | 101 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required. | Item98 | 4 | Each |
| 101 | 102 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)_6 way, Double door | Item99 | 1 | Each |
| 102 | 103 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required._Single pole | Item100 | 4 | Each |
| 103 | 104 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required._63 amps | Item101 | 1 | Each |
| 104 | 105 | Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps \"C\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. | Item102 | 2 | Each |
| 105 | 106 | NON SHEDULE ITEMS | |||
| 106 | 107 | Supply of Trans air 12\" Freshair Exhaust fan suitable for 50 Hz AC supply of Crompton / Standard Refresh Air - DB 12\" Fresh air Exhaust fan / Havells Ventil Air DB4 Blade (300 mm) make.as approved by Engineer in-charge | Item103 | 2 | Each |
| 107 | 108 | Supply at site 1x100W GLS BC Industrial Bulk Head Fitting, Crompton / Bajaj make or as approved by Engineer Incharge | Item104 | 14 | Each |
| 108 | 109 | Supply at site Cool white LED Bulb 9Watt, Base type B22, Bajaj/ Philips/ Sysca make or as approved by Engineer Incharge | Item105 | 14 | Each |
AI Tender Summary
Tender Timeline
May 21, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedJun 01, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJun 03, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender