| 1 | 1 | Providing and fixing Low Height Partitions at required location having minimum thickness of 65mm made of Central Province Teak Wood (CPTW) confirming to IS 399-1963 of 50mm x 50mm finished size section framing at 600mm center to center, covered with 6mm thick Marine Plywood confirming to IS 710-1980 on both sides. The partition shall be finished with Decorative Laminate sheet confirming to IS 2046 with or without grooves externally with necessary lipping of Burma Teak Wood, molding, anti-termite treatment to all plywood and wood work and two coats of Melamine Polish to all plywood and wood work etc. complete. | 1 | 1 | Per Square Meter |
|---|
| 2 | 2 | Providing and fixing Full Height Partitions at required location having height more than 1.34m having minimum 65mm thick made of Central Province Teak Wood (CPTW) confirming to IS 399-1963 of 50mm x 50mm finished size section framing at 600mm center to center, covered with 6mm thick Marine Plywood confirming to IS 710-1980 on both sides. The partition shall be finished with Veneer with or without grooves externally with necessary lipping of Burma Teak Wood, molding, anti-termite treatment to all plywood and wood work and two coats of Melamine Polish to all plywood and wood work etc. complete. | 2 | 1 | Per Square Meter |
|---|
| 3 | 3 | Providing & fixing Dias of size 500mm x 600mm x 450mm height with table top of 25mm thick Plain Particle Board of exterior grade confirming to IS 3087-1986 with Post Forming Laminate on top & Balancing Laminate below with 2mm thick, PVC Edge-Band of required size, sides and bottom of 25mm thick both side Prelaminated Particle Board Grade-I Type-I of exterior grade confirming to IS 12823-1990 with 2mm thick PVC Edge-Band of required size, required hardware, wooden dowels, right angle connector, head screw & cap etc., anti-termite treatment to all plywood and wood work and two coats of French Polish confirming to IS 2338 to all plywood and wood work etc. complete. | 3 | 1 | Per Square Meter |
|---|
| 4 | 4 | Providing and fixing Full Height Door Shutter at required location having height more than 1.5m made by using Solid Core Type Wooden Flush Door confirming to IS 2202-1999, 35mm thick finished with Decorative Laminate Sheet confirming to IS 2046 with or without grooves externally with necessary lipping of Burma Teak Wood, molding, anti-termite treatment to plywood and wood work and two coats of French Polish confirming to IS 2338 to all plywood and wood work including all leads and lifts etc. complete. | 4 | 1 | Per Square Meter |
|---|
| 5 | 5 | Providing and fixing Full Height Door Shutter at required location having height more than 1.5m made by using Solid Core Type Wooden Flush Door confirming to IS 2202-1999, 35mm thick with Veneer with or without grooves externally with necessary lipping of Burma Teak Wood, molding, anti-termite treatment to plywood and wood work and two coats of Melamine Polish to all plywood and wood work etc. complete. | 5 | 1 | Per Square Meter |
|---|
| 6 | 6 | Providing and fixing 53cm deep Cupboard Type Full Height Storage Unit made of 19mm thick Marine Plywood confirming to IS 710-1980 for frames, internal verticals, horizontal divisions, shutters and 6mm & 12mm thick Marine Plywood for drawers with locks, handles, hardware, lipping & beading patti of Burma Teak Wood, finished with Veneer in approved pattern with grooves and two coats of French Polish confirming to IS 2338 and two coats of Melamine Polish for all molding & lipping patties with anti-termite treatment to plywood & wood work etc. complete. | 6 | 1 | Per Square Meter |
|---|
| 7 | 7 | Providing & fixing on site 40cm Deep Cupboard Type Low Height Storage Unit less than 1.35m height made od 19mm Marine Plywood confirming to IS710-1980 for frame, internal verticals, horizontal divisions, openable shutters, 6mm thick Marine Plywood back with necessary locks, handles, hardware, lipping of Burma Teak Wood, molding, finished with Decorative Laminate confirming to IS 2046 sheet finished with lamination pattern with grooves externally and two coats of French Polish confirming to IS 2338 with anti-termite treatment to plywood & wood work etc. complete. | 7 | 1 | Per Square Meter |
|---|
| 8 | 8 | Providing & supplying Table confirming to IS 3663-2005 & IS 4414-1990 of size 2.13m x 0.91m made out of 19mm thick Marine Plywood confirming to IS 710-1980 top, side & apron having 38cm x 54cm x 75cm storage boxes on both sides made up of 19mm Marine Plywood for sides, shutters, horizontal and vertical divisions of 12mm (6mm x 2) thick Marine Plywood back and three drawers on one side made by using 19mm Marine Plywood front and sides, 6mm Marine Plywood bottom with necessary lipping of Burma Teak Wood, moldings and Footrest of Central Province Teak Wood (CPTW) confirming to IS 3663-2005 of 75cm x 40cm finished size and front height 4cm and rear height 10cm. The table to be externally finished with 4mm thick group match Veneer having pattern with grooves including necessary lipping of Burma Teak Wood, moldings, two coats of French Polish confirming to IS 2338 with anti-termite treatment, Melamine Polish for Veneer and exposed lipping, moldings, anti-termite to plywood and wood work etc. complete. | 8 | 1 | Per Square Meter |
|---|
| 9 | 9 | Providing & supplying Table confirming to IS 3663-2005 & IS 4414-1990 of size 120cm x 60cm x 76cm height made out of 19mm thick Marine Plywood confirming to IS 710-1980 top, vertical side & 6mm Marine Plywood sides, bottom with necessary sliders, one open shelf of 19mm thick of Marine Plywood with necessary lipping on external sides and Footrest of Central Province Teak Wood (CPTW) confirming to IS 3663-2005 of 75cm x 40cm finished size and front height 4cm and rear height 10cm. The external side and top shall be finished with 1mm thick Decorative Laminate confirming to IS 2046 having matt/suede/fine line finished lamination pattern with grooves, all internal surfaces on table and drawer shall be finished with two coats of French Polish confirming to IS 2338 with anti-termite treatment to plywood and wood work etc. complete. | 9 | 1 | Per Square Meter |
|---|
| 10 | 10 | Providing and supplying Executive Chair with dimensions confirming to IS 3663-2005 made in well-seasoned old Burma Teak Wood with carved details, as per the Architects’ Drawing. The seat shall be covered with Composite Leather and the back shall be netted in Cane, all wooden surfaces shall be finished with two coats of French Polish confirming to IS 2338, including spray coating all surfaces with approved anti-termite solution etc. complete. | 10 | 1 | Per Number |
|---|
| 11 | 11 | Providing & supplying Semi-Circular Chair with dimensions confirming to IS 3663-2005 made in well-seasoned old Burma Teak Wood as per the Architects’ Drawing. The seat shall be netted in Cane, all wooden surfaces shall be finished with two coats of French Polish confirming to IS 2338, including spray coating all surfaces with approved anti-termite solution etc. complete. | 11 | 1 | Per Number |
|---|
| 12 | 12 | Providing & supplying Revolving Chair with dimensions confirming to IS 3663-2005 having a high back with an adjustable head rest with a synchronized tilting mechanism with multiple locking system, Acrylonitrile Butadiene Styrene - ABS for seat, cushioned back with extra lumber support with fine tuning for depth adjustment, with swivel & depth. The chair shall have adjustable arm pad & option of PVC padding. The seat shall have a gas lift for height adjustment and a Nylon base with castors etc. complete. | 12 | 1 | Per Number |
|---|
| 13 | 13 | Providing & supplying Visitor Revolving Chair with dimensions confirming to IS 3663-2005 having a medium back with head rest, with a synchronized tilting mechanism with multiple locking systems, Acrylonitrile Butadiene Styrene - ABS for seat, with swivel & depth. The chair shall have adjustable arm pad & option of PVC padding. The seat shall have a gas lift for height adjustment and a Nylon base with castors etc. complete. | 13 | 1 | Per Number |
|---|
| 14 | 14 | Providing & supplying Fix Chair with dimensions confirming to IS 3663-2005 having the seat and back made up of 1.2cm thick Hot-Pressed Plywood confirming to IS 303, upholstered with fabric upholstery covers and molded Polyurethane Foam. The back foam shall be designed with contoured lumbar support for extra comfort. The seat shall have extra thick foam on front edge to give comfort to popliteal area. Back size shall be 47.5cm (W) x 58cm (H), Seat size shall be 47cm (W) x 48cm (D). The Polyurethane Foam shall be molded with density 45+/-2 kg/m3 and hardness 20+/- 2 on Hampden Machine at 25% compression, one-piece armrests shall be injection molded from black Copolymer Polypropylene etc. complete. | 14 | 1 | Per Number |
|---|
| 15 | 15 | Providing & supplying Two-Seater Sofa of overall size 1350mm x 760mm x 825mm height made of Country Cut Teak Wood (CCTW) confirming to IS 399-1963 of 75mm x 38mm finished size section frame, 6mm Commercial Plywood confirming to IS 303 for necessary covering from back & arm rests. The seat shall be 100mm thick heavy density foam covered with 1\" soft foam and arms of CCTW 50mm thick with 50 density foam covered with 1\" plain soft foam. All work covered with tapestry fabric including necessary hardware, nawar, jute cloth, casement, springs or belted absorber etc. complete. All exposed wooden surface shall be finished with two coats of Melamine Polish and anti-termite treatment to plywood and woodwork etc. complete. | 15 | 1 | Per Number |
|---|
| 16 | 16 | Providing and supplying Stool of Country Cut Teak Wood (CCTW) confirming to IS 399-1963 of size 0.45m x 0.45m of height 0.75m and top of 25mm thick, as per typical drawing finished with two coats of French Polish confirming to IS 2338 etc. complete. | 16 | 1 | Per Number |
|---|
| 17 | 17 | Providing & supplying Glass Tabletop confirming to IS 2835-1998 of 8mm thick in required size and shape including finishing the all side edges smooth mechanically etc. complete. | 17 | 1 | Per Square Meter |
|---|
| 18 | 18 | Providing, supplying, and fixing Roller Blind Fabric Curtains for window using Powder Coated Rod and mechanical system with chain for opening/closing movements of the blinds and fixing properly at site etc. complete. | 18 | 1 | Per Square Meter |
|---|
| 19 | 19 | Providing & supplying Tablecloth confirming to IS 3773-2000 | 19 | 1 | Per Square Meter |
|---|
| 20 | 20 | Providing and supplying Footrest below table as per IS 3663-2005 of 75cm x 40cm size and front height 4cm & rear height 10cm using Commercial Plywood 18mm thick with two coats of French Polish confirming to IS 2338 and finishing etc. complete. | 20 | 1 | Per Number |
|---|
| 21 | 21 | Providing, supplying, and fixing on site Single Static Drive Type Body 2 Bay of Compactors of size 1790mm x 445mm x 2375mm made out of 0.8mm thick Cold Rolled Cold Annealed Steel conforming to IS 513 Grade, having 5 loading levels (Load Bearing Capacity - 80 Kgs Uniformly Distributed Load) formed by 4 Nos of adjustable shelves, finished with Fire Retardant Epoxy Polyester Powder Coating of approved color & shade with a Dry Film Thickness of minimum 40 microns, oven baked with a controlled temperature of 180 deg. C to 200 deg. C, the undercarriage made up of welded frame of Hot Rolled Steel sheet 3.15mm thick conforming to IS 10748 suitably fabricated to take the load based on configuration having fasteners, label holders, mounted on guide channels as per approved specifications and design etc. complete. Vertical structure to be 'J' profile. Two such 'J' profiles to be joined with full steel sheet and welded for additional strength. Shelf to have minimum 30mm bend. Each shelf to have minimum 10 bends etc. complete. | 21 | 1 | Per Number |
|---|
| 22 | 22 | Providing, supplying, and fixing on site ABC 6 Kg Fire Extinguisher confirming to IS 15683-2006 with Valve Pressure Gauge, PVC Hose Pipe, Safety Pin, Wall Bracket etc. complete. | 22 | 1 | Per Number |
|---|
