Construction Of Addtional Accommodation Building For Primary Health Centre At Panchrukhi Distt. Kangra H.P. (Sh:- Construction Of Addtional Accommodation Main Building Civil Work Including Water Supply And Sanitory Installation And Rain Water Harvesting S
Tender Value
2.72 Crore
Estimated cost
Bid Submission
27 Mar 2020
0 days left
EMD
3.05 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaisinghpur → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Addtional Accommodation Building For Primary Health Centre At Panchrukhi Distt. Kangra H.P. ( Sh:- Construction Of Addtional Accommodation Main Building Civil Work Including Water Supply And Sanitory Installation And Rain Water Harvesting System ) .
BOQ
| Name of Work: Construction of Addtional Accommodation Building for Primary Health Centre at Panchrukhi Distt. Kangra H.P. (SH:- Construction of Addtional Accommodation main building civil work including water supply and sanitory installation and rain water harvesting system ). | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Excavation in foundation, trenches etcetera in earth work involving all classification of soil such as pick work, pick jumper work, blasting work, soft or hard rocks including chiseling/wedging out of rocks where blasting work is prohibited or any other mixed variety of intermediate soil, dewatering and removal of slush if arrisen during course of construction and lifts upto all heights including stacking the excavated soil not more than three meters clear from the edge of the excavation and then returning the stacked soil in 15 cm (fifteen centimeters) thick layers when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming and watering and then disposing of all surplus excavation earth within all leads,lifts by any mode of transportation and other incidental, as per the direction and entire satisfaction of Engineer-In-Charge. Any loss to the private and public property during course of construction shall be absolute responsibility of the contractor. | 498.62 | Per cubic metre | |
| 2 | 2 | Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 39.77 | Per cubic metre | |
| 3 | 3 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in foundation,. Footings bases of columns and mass concrete. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 128.91 | Per square metre | |
| 4 | 4 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns, pillars , posts and struts, square, rectangular, polygonal in plain. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1229.58 | Per square metre | |
| 5 | 5 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings and the like floor etc. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1308.73 | Per square metre | |
| 6 | 6 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams haunchings, cantilevers bressumers and lintels upto all depths. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1326.9 | Per square metre | |
| 7 | 7 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls up to any width. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 393.23 | Per running metre | |
| 8 | 8 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls up to any thickness but not. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 45 | Per square metre | |
| 9 | 9 | Providing form work with steel plates of 3.15mm (three decimal one five milimeter) thick, welded with angle iron in frames of 30x30x5mm (thirty into thirty into five milimeter) so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 213.98 | Per square metre | |
| 10 | 10 | Providing and laying cement concrete 1:6:12 (One cement isto six sand isto twelve aggregate) graded crushed/broken stone aggregate 40mm (forty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 43.19 | Per cubic metre | |
| 11 | 11 | Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight aggregate) graded crushed/broken stone aggregate 40mm (fourty milimeter) nominal size mechanically mixed and curing complete, excluding cost of form work in foundation and plinth. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 56.85 | Per cubic metre | |
| 12 | 12 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-30 design mix to obtain the minimum compreasive strength of M-20 N/mm2 with cement contents not less than of 330kg/m3 (three hundred thirty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in foundation footing, basis of columns and the like mass concrete upto floor all level and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction of Engineer-in-Charge. | 94.56 | Per cubic metre | |
| 13 | 13 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 desing mix to obtain the minimum commpressive of strength of M-20 N/mm2 with cement concrete not less than 320 Kg mm3 excluding cost of form work and reinforcement for reinforced concrete work in walls any thickness but not less than 0.10mtrs. (zero point one zero metre) thickness including attached pilasters, buttresses plinth and string courses upto any depth and height including curing complete and carriage of material within all leads, lifts and other incidental charges complete in all respect as per the direction of Engineer-in-Charge. | 14.4 | Per cubic metre | |
| 14 | 14 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in columns, pillars posts and struts upto floor all level and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per the direction of Engineer-in-Charge. | 166.98 | Per cubic metre | |
| 15 | 15 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N.mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in suspended floor, roofs, landing and shelves and their support balconies beams girders bressumers and cantilevers upto floor all level and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per the direction of Engineer-in-Charge. | 363.02 | Per cubic metre | |
| 16 | 16 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) excluding cost of form work and reinforcement for reinforced concrete work in stair cases (except spiral stair cases) excluding landing but including preparing of top surface and finishing of nosing upto all floor level and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction of Engineer-in-Charge. | 20.5 | Per cubic metre | |
| 17 | 17 | Providing and laying mechanically mixed and vibrated reinforced cement concrete work grade M-20 design mix to obtain the minimum compressive strength of M-20 N/mm2 with cement contents not less than of 320kg/m3 (three hundred twenty kilogramme per cubic metre) including cost of form work but excluding reinforcement for reinforced concrete work in moulding as a cornices window sills etc not exceeding in 15 (fifteen) centimetre in grith and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction of Engineer-in-Charge. | 6.64 | Per cubic metre | |
| 18 | 18 | Providing tor steel reinforcement for reinforced cement concrete work including bending, binding and placing in position complete in all respects as per drawing and design in all floor levels including the cost of binding wire as per PWD specification and approved design. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 135295 | Per kilo gram | |
| 19 | 19 | Providing and laying damp proof course 100mm (one Hundred milimetre) thick with cement concrete 1:2:4 (one cement isto two sand isto four aggregate) graded crushed/broken stone aggregate 12.5mm (tewelve decimal five milimeter) nominal size mechanically mixed and curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 83.65 | Per square metre | |
| 20 | 20 | Applying a coat of hot bitumen (mexphalt) 80/100 (Eighty by hundred) or equivalent using 1.70 kg (one decimal seven zero) kilogram per square meter on damp proof course after cleaning the surface with a piece of cloth lightly socked with kerosene as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 83.65 | Per square metre | |
| 21 | 21 | Providing and laying 20 cm (twenty centimetre). thick composite stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6(1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm (twenty millimetre). nominal size) on inner face of walls including centring, shuttering and propping complete up to all floor level and curing complete including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction of Engineer-in-Charge. | 1539.69 | Per square metre | |
| 22 | 22 | Construction of 40cm (forty) centimetre thick cavity wall consisting 10cm (ten centimetere) wide cavity and 20cm (twenty centimetre) thick outer wall and 10cm (ten centimetere) thick inner wall of precast cement concrete block laid in cement mortar 1:6 (one cement is to six sand) and strengthed with hoop iron and bitumen coated cross ties including making weep holes and vent hole complete. 2 Nos 6/8mm dia bars in Z shape crossing each other shall be provided at the internals 90 to 100 cm (ninty to hundred) centimetere length and vertically in cavity and at the time of masonry work it may be ensured that the cavity between the wall dose not get fill up with cement mortor ( area of one face will be considered for payment) including all leads & lifts of material and as per the direction and entire satisfaction of Engineer-In-Charge. | 19.31 | Per square metre | |
| 23 | 23 | Precast concrete block masonry in partition walls 10cm (ten centimetre) thick with solid block of approved size including quion blocks, jamb blocks, closer etcetra made of cement concrete 1:3:6 (one cement : three sand : six graded/crushed, crushed stone aggregate 40mm (forty millimetre) and down gauge) in cement mortat 1:6 (one cement : six sand) upto all floor level including curing and carriage of materials within all leads and lifts complete in all respect as per direction of Engineer in Charge. | 575.09 | Per square metre | |
| 24 | 24 | Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded stone aggregate 20mm (twenty) millimeter nominal size mechanical mixed in cement mortor 1:6 (one cement six sand) including curring and carriage of material within all leads and lifts complete in all respect as per direction of Engineer in Charge. | 14.65 | Per cubic metre | |
| 25 | 25 | Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:6 (one cement : six sand) and curing complete including carriage of materials within all leads and lifts complete in all respect as per the direction of Engineer-in-Charge. | 28.79 | Per cubic metre | |
| 26 | 26 | Providing and fixing anodized aluminum natural wooden shade of Jindal work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodized transparent or dyed to required shade according to IS 1868 (Minimum anodic coating of grade AC 15) frame for entrance door No. 14081 size 127x44.45x3.19mm (one hundred twenty seven into four four point four five into three point ninteen) millimetre and internal door frame No. 14081 size 101.60 x 44.45x 3.18mm (one hundred one point sixty into four four point four five into three point eighteen) millimetre fixed with raw plugs and screws or with fixing clips, or with expansion hold fasters including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC neoprene felt etc. Aluminum sections shall be smooth rust free, straight, mitred and jointed mechanically where ever required including cleast angle, aluminum, snap beading for glazinge / panelling C.P. brass / stainless steel screws. All complete as per architectural drawings with in all leads and lifts of materials and other incidentals as per approved drawing and entire satification of Engineer-in-Charge. | 6976.7 | Per kilo gram | |
| 27 | 27 | Providing and fixing anodised aluminium natural wooden shade of Jindal work shutters for doors windows & ventilators including providing and fixing hinges / pivots and making provisions for fixing of fittings with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up to gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazing/ panelling CP brass / stainless steel screws . All complete as per architectural drawings with in all leads and lifts of materials and other incidentals as per approved drawing and entire satification of Engineer-in-Charge. | 2572.72 | Per kilo gram | |
| 28 | 28 | Providing and fixing 12mm (Twelve millimetre) Thick Prelaminated board in matt finished ISI marked NO 12823 as per approved shade of viromica / kit ply / nona pan / green ply both side BWP phenol bonded exterior / interior grade panelled shutter with frame of first class Deodar wood including bright finished black enameled butt hinges with necessary screws 40 mm (Forty millimetre) thick shutter as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 100.07 | Per square metre | |
| 29 | 29 | Providing and fixing 40 mm (Forty millimetre) thick second class Deodar wood wire gauge shutters using galvanised MS wire gauge of IS gauge designation 85G with wire of dia 0.56 mm (Zero decimal five six millimetre) for doors, windows and clearstory windows including bright finished black enamelled iron hings with necessary screws as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 167.64 | Per square metre | |
| 30 | 30 | Providing and fixing glazing with glass pans of 4mm (four millimetre) thickness (weight not less than 10.00 kg/sqm (ten point zero zero kilogramme per square metre)) in aluminium door, window, ventilator shutters and partition etcetra with PVC/neoprens gaskets etcetra (Cost of aluminium snap beading shall be paid in basic item) complete in all respect with in all leads, lifts, carriage of material, other incidential charges complete as per Architectural Drawings and the direction of the Engineer-in-Charge . | 490.92 | Per square metre | |
| 31 | 31 | Providing and fixing glazing with glass pans of 6mm (six millimetre) thickness (weight not less than 13.75 kg/sqm (thirteen point seventy five kilogramme per square metre) in aluminium door, window, ventilator shutters and partition etcetra with PVC/neoprens gaskets etcetra (Cost of aluminium snap beading shall be paid in basic item) complete in all respect with in all leads, lifts, carriage of material, other incidential charges complete as per Architectural Drawings and the direction of the Engineer-in-Charge . | 1.98 | Per square metre | |
| 32 | 32 | Providing and fixing 25mm (twenty five milimeter) thick pre laminated / MDF board in shelves / box for cup board with butt joints and fixing with nails and screws etc. complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 46.85 | Per square metre | |
| 33 | 33 | Providing and fixing 19mm (Nineteen millimetre) thick MDF board water proof shutter for cup board including fixing with nickel plated piano hinges with screws etcetra, the all cup board portion of shutter shall be finished with 6mm (Six millimetre) thick hard wood edging with necessary screws as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 22.89 | Per square metre | |
| 34 | 34 | Providing and fixing grills of required pattern in steel frames of windows etc. with M.S. flats with round beaded bolts and nuts or by screw.plain grill as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 966.6 | Per\n kilo gram | |
| 35 | 35 | Providing and fixing anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 300x16mm (Three hundred into sixteen milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 7 | Each | |
| 36 | 36 | Providing and fixing anodized aluminum sliding door bolt, anodized transparent or dyed to required colour and shade with bolts and nuts, screws etcetra complete. 250x16mm (Two hundred fifty into sixteen milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 66 | Each | |
| 37 | 37 | Providing and fixing anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete 250x10mm (Two hundred fifty into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 154 | Each | |
| 38 | 38 | Providing and fixing anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete 150x10mm (One hundred fifty into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 864 | Each | |
| 39 | 39 | Providing and fixing anodized aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetra complete.100x10mm (one hundred into ten milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 40 | Each | |
| 40 | 40 | Providing and fixing anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.125mm (one hundred twenty five milimeter) size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 168 | Each | |
| 41 | 41 | Providing and fixing anodized aluminum handle anodized transparent or dyed to required shade or colour with necessary screws etcetera complete.100mm (one hundred milimeter) nominal size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 452 | Each | |
| 42 | 42 | Providing and fixing oxidized bright finished hard drawn M.S. hooks and eyes. 150mm (one hundred fifty) millimeter nominal size. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 216 | Each | |
| 43 | 43 | Providing and fixing 65 x 35mm (sixty five into thirty five) millimeter special quality bright finished brass cup board locks or ward robe lock with six levers including necessary screws etc complete (Indian make of approved quality) with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 8 | Each | |
| 44 | 44 | Providing and laying eternity glazed viterified tiles 600x600x10mm (six hundred into six hundred into ten) millimeter in grey / coloured of Kajaria / Asian / Johnson & Johnson manufactured approved shade in flooring treads of steps and landing on a bed of 12mm thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1167.21 | Per square metre | |
| 45 | 45 | Providing 4 mm (four milimetre) thick PU floor of Epoxy PIDIPOXY ESL of pidilite flooring comprising of flow fresh SL part A @ 1.2 kg/sqm ( one point two kilograme per square metre), flow fresh SL part B @ 1.24 kg/sqm ( one point two four kilograme per square metre) flowfresh SL filler @ 4.98 kg/sqm ( Four point nine eight kilograme per square metre) flowfresh SL PIGMENT @ 0.010 kg/sqm ( zero point zero one zero kilograme per square metre), high solid floor coating @ 1.04 kg/sqm ( one point two zero four kilograme per square metre), Epoxy coving @ 1.25 RMT/sqm ( one point two five per running metre) and pencil coving @0.021 Rmt/sqm ( zero point zero two one per running metre) as per direction of Engineer in Charge complete complete with in all leads, lifts and other incidentals. | 66.18 | Per square metre | |
| 46 | 46 | Providing and laying 50mm (fifty) millimeter thick CC ironite flooring with metallic concrete hardner teking under layer of 35mm (thirty five) millimeter thick cement concrete 1:2:4 (one cement two sand 4 graded stone aggregate) 20mm (twenty) millimeter nominal size and top layer of 15cm (fifteen) centimeter thick metallic concrete hardner consisting of mix 1:2 (one cement hardener mix 2 stone aggregarte) 6mm (six) millimeter nominal size by volume with which metallic hardening compound of approved quality is mixed in the ratio 4:1 ( four of cement : one part of metallic floor handening compound of approved quality by weight) including finishing complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 52.49 | Per square metre | |
| 47 | 47 | Cement plaster skriting 20mm (twenty millimetre) thick (upto any height) with cement mortar 1:3 (one cement : three sand) finished with a floating of neat cement including rounding of junction with floor complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 6.01 | Per square metre | |
| 48 | 48 | Providing and laying digital glazed viterified tiles 600x600x8mm (six hundred into six hundred into eight) millimeter in eternity HD in stain/stone finish of Kajaria / Asian / Johnson & Johnson manufactured grey / coloured of required shade in skirting, risers of steps and dados on 12mm thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 557.06 | Per square metre | |
| 49 | 49 | Providing and laying 25mm (twenty five millimeter) thick Single piece Kota stone slab flooring 20mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 55.8 | Per square metre | |
| 50 | 50 | Providing and laying Single piece Kota stone slab 25mm (twenty five millimeter) thick in risers of steps, skirting dado and pillars laid on 12mm (twelve millimeter) (average) thick cement mortar 1:3 (one cement : three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 18.9 | Per square metre | |
| 51 | 51 | Painting two coats with high Glossy 3D Epoxy paint for interior wall painting with epoxy paint roller brushes plian smooth finish composed of acrylic polymere in emulsion inorganic/special pigment sillceous aggregate antifungicides anti-rusting & foaming in two coats i/c necessary putty to give smooth even surface , sand papering smooth complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 152.26 | Per square metre | |
| 52 | 52 | Providing and laying marble work in flooring 20mm (Twenty millimetre) thick white makrana marble table rubbed laid over a base of 12 mm (Twelve millimetre) thick in cement mortar 1:3 including jointing with white cement mortar 1:2 (one cement : two marble dust) with an adimixture of pigment to match the shade of the marble complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 17.89 | Per square metre | |
| 53 | 53 | Providing and laying red sand stone slab in treads and risers of steps on a bed of 20mm (twenty milimetre) thick cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including preparing of nosing including rubbing and granite polish finish complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 181.38 | Per square metre | |
| 54 | 54 | Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in in skirting dado (300 x 600mm) nominal size (three hundred into six hundred millimetre) treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement three sand) finished with flush pointing in white cement as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 372.06 | Per square metre | |
| 55 | 55 | Providing and laying Kota stone slab 25mm (twenty five millimeter) thick in risers of steps, skirting dado and pillars laid on 12mm (twelve millimeter) (average) thick cement mortar 1:3 (one cement : three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing including carriage of material within all leads and lifts complete in all respect. | 5.44 | Per square metre | |
| 56 | 56 | Providing and fixing pre-painted sheet roofing of kotar metal single skin trapezoidal sheeting 0.60mm (sixty milimetre) thickness having 1060mm (one thousand sixty millimetre) cover width cover all width 1126mm (one thousand one hundred twenty six milimetre) , 28mm (twenty eight milimetre) crest depth at 353mm (three hundred fifty three millimetre) 2.50mm (two point fifty millimetre) the main crest with at top 25mm (twenty five) and at lower 81mm (eighty one milimetre) base metal of coil rolled steel coil with zinc waiting top coat with regular modified polysters coating of approved shade and balancing reverse coat with self topping screws 5.5mm (five decimal five millimetre) dia and 55mm (fifty five millimetre) length with EPDM seal complete in all respect as per approved drawing design and in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 973.07 | Per square metre | |
| 57 | 57 | Providing and fixing pre-painted sheet ridge or hips 60cm (sixty centimetre) over all of kotar metal skin trapezoidal profiled sheeting 0.60mm (zero point sixty centimetre) cover with over all width 1126mm (one thousand one hundred twenty six) 28mm (twenty eight) crest depth at 353mm (three hundred fifty three) 2mm (two millimetre) C/C crest distance. There will be two ribs at the centre for stiffening heaving crest depth of 2.50mm (two point five millimetre) the main crest with at top zinc waiting top coat with regular modified polyster coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 55mm (fifty five millimetre) length with EPDM seal complete in all respect as per approved drawing design and in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 177.87 | Per running metre | |
| 58 | 58 | Providing and fixing pre-painted sheet valleys 90cm (ninety centimetre) over all of kotar metal single skin trapezoidal profiled sheet 0.60cm (zero point sixty centimetre) thickness having 1060mm cover width over all width 1126mm (one thousand one hundred twenty six millimetre) 28mm (twenty eight millimetre) crest depth at 353mm +2mm (three hundred fifty three millimetre plus two millimetre) C/C crest distance. There will be two ribs at the centre for stiffening heaving crest depth of 2.5mm (two point five milimetre) . The main crest with at top 25mm (twenty five millimetre) and at lower 81mm (eighty one millimetre) base metal of cold rolled steel coil with zinc waiting top with regular modified polysters coating of approved shade and balancing EPDM seal complete in all respect as per approved drawing, design and in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 8 | Per running metre | |
| 59 | 59 | Providing and fixing plaing M.S. B.P. sheet 1.66mm (one decimal sixty six millimetre) thick to 2.00mm in evels board/ Facia / Sofit / Ceilling including cutting fixing jointing with gass/electric welding to steel roofs members and applying a coat of red lead primer complete as per PWD specification (frame work is to be measured paid for separately). The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 229.41 | Per square metre | |
| 60 | 60 | Providing and fixing 15cm(fifteen centimetre) wide 45cm (forty five millimetre) over all semicircular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design 0.63mm thick sheet as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 265.66 | Per square metre | |
| 61 | 61 | Providing and fixing on wall face PVC (D-plast) rain water pipes of working pressure not less than 4.5 kg (four decimal five kilogram) per square meter including filling the joints with approved adhesive complete 100 mm (one hundred milimeter) dia. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 199.5 | Per running metre | |
| 62 | 62 | Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete 110mm (one hundred ten milimeter) dia PVC plain bend as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 36 | Each | |
| 63 | 63 | Providing and fixing on wall face PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete 110mm (one hundred ten milimeter) dia PVC plain shoes as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 18 | Each | |
| 64 | 64 | Providing and fixing 100mm (one hundred millimetre) diametre pipe MS holder bat clamps of approved design to CI ,SCI or PVC pipes embeded in and including cement concrete blocks 10x10x10cm (ten into ten into ten centimetre) of 1:2:4 (one cement : two sand : four stone aggregate 20mm (twenty millimetre) nominal size) and cost of cutting holes and making good the wall etcetra including carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 135 | Each | |
| 65 | 65 | Steel work welded in built up sections composed in beams, joists, channels, angles, tees plated with connecting plates framed work with 40x6 mm (Forty into six millimetre) tees , flats, gratings, bars, ladders tcetra with connecting plates angles, cleats as in trusses and trussed purlins, main and cross beams, hips, jack rafters, purlins connect to common rafter and like work including cutting hoisting fixing in position & applying a priming coat of red lead paint complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 217.55 | Per quintal | |
| 66 | 66 | Painting two or more coats(excluding priming costs) on new steel and other metal surfaces with enamel paint to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 326.07 | Per square metre | |
| 67 | 67 | 6mm (six millimeter) cement plaster 1:3 (one cement isto three sand) in ceiling complete including curing complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1257.3 | Per square metre | |
| 68 | 68 | Providing and fixing cement bounded particial board 8 mm.thick (eight milimetre) particial board ceiling of approved quality with butt jointing and nails ( frame work and cover fillets to be paid for sepertely) .The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 257.8 | Per square metre | |
| 69 | 69 | 15mm (fifteen milimeters) thick cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimetewrs) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1931.1 | Per square metre | |
| 70 | 70 | 15mm (fifteen milimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimeters) in girth, in rough side with cement mortar 1:6 (one cement isto six sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1931.09 | Per square metre | |
| 71 | 71 | 15mm (fifteen milimeter) thick cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto any floor level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty milimeters) in girth, in rough side with cement mortar 1:5 (one cement isto five sand) complete including curing as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1784.61 | Per square metre | |
| 72 | 72 | Finishing wall with weather proof exterior emulsion of Ultrateck/ Spetrum Nerolac/ Asian paint of approved brand and manufacture on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1784.61 | Per square metre | |
| 73 | 73 | Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 5811.28 | Per square metre | |
| 74 | 74 | Distempering (two coats) with oil bound washable distemper of Asian/ Nerloac brand and manufacture and of required shade on undecorated wall surfaces/ celling/ sloping roof to give an even shade over and including and priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1257.31 | Per square metre | |
| 75 | 75 | Distempering (two coats) with synthetic washable distemper of Asian/ Nerolac brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including and priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 2823.4 | Per square metre | |
| 76 | 76 | Wall painting (two coats) with acrylic emulsion paint of Asian/ Nerolac brand and manufacture for interior grade on undacurated concrete/stone/plastered wall surface to give an even shade including throughly brushing the surface free from mortor dropping and other foreign matter and sand papering smooth including applying of putty as required for metaling the surfac complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 2823.4 | Per square metre | |
| 77 | 77 | Providing and fixing C.P. Grabbor 40mm (forty milimetre) dia at 78cm (seventy eight centimetre) height with M.S. plate as per detail as the position of the seat and wash basin complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 2 | Each | |
| 78 | 78 | Prividing and fixing railing for stair case having baluster of 19x19mm (nineteen into nineteen millimetre) M.S. solid bars SWG-16 (Sixteen) gauge with a clear height of 85 cm (Eighty centimetre) @ 30 cm (thirty centimetre) center to center jointing in cement concrete steps and jointing with electric / gas welding at top along with hand rail of teak wood 6.25 x 7.50cm ( six poit two five into seven point five zero) vertical balusters welding/ jointed with each other with 2 (Two) Numbers MS flat of 37 x5 mm (thirty seven into five millimetre) complete with applying priniming coat of red lead paint complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 30.15 | Per running metre | |
| 79 | 79 | Prividing and fixing railing for stair case having baluster of 25 mm( twenty five milimetre) Dia M.S. pipe with a clear height of 85 cm (Eighty centimetre) @ 60 cm (sixty centimetre) center to center jointing in cement concrete step and jointing with electric / gas welding at top along with hand rail of hollow MS pipe of 50 mm (fifty milimetre) dia(SWG-18) vertical baluste welding/ jointed with each other with 2 (two) Nos MS flat of 50x5 mm (fifty into five millimetre) complete with applying priniming coat of red lead paint complete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 6.5 | Per running metre | |
| 80 | 80 | Providing under layer for plinth protection of 75mm (seventy five milimeters) thick bed of dry brick/stone aggregate 40mm (forty milimeters) nominal sizes well rammed and consolidated and grouted with fine sand including preparation of ground as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 80.42 | Per square metre | |
| 81 | 81 | Providing plinth protection 50mm (fifty milimeters) thick cement concrete 1:3:6 (one cement isto three sand isto six aggregate) 20mm (twenty milimeters) nominal size cushed/broken stone aggregate including finishing the top surfaces of concrete smooth including curing comlete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 80.42 | Per square metre | |
| 82 | 82 | Construction course rubble hammer dressed ‘U’ shape open surfaces drain with side wall 15x23cms ( fifteen into twenty three centimeters) in cement mortar 1:6 (one cement isto six sand) and inside plastering with cement plaster 1:3 (one cement isto three sand) including earth work and laying 10cm (Ten centimeters) cement concrete in 1:5:10 ( one cement isto five sand isto ten aggregate) 40mm (forty milimeters) nominal size and 7.5cm (seven decimal five centimeters) cement concrete 1:2:4 (one cement isto two sand isto four aggregate) 20mm (twenty milimeters) nominal size and finished with a floating cost of neat cement complete as per standard drawing and design including curing comlete as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 134.03 | Per runninmg metre | |
| 83 | 83 | Providing and fixing 10 cm (Ten centimetre) diametre M.S. pipe as per PWD specification complete including entire carriage of materials within all leads and lifts as per direction of Engineer-in-Charge. | 8.7 | Per runninmg metre | |
| 84 | 84 | Providing and laying Unistone 12mm.(twelve milimetre) cladding on R.C.C.surface side as on faces of Arch masonry walls etc.on 12mm. thick cement plaster 1:3(1cement:3sand) and jointed with cement slurry including scaffolding extcetra. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 128.88 | Per square metre | |
| 85 | 85 | Providing and laying Barium Sulphate plaster in walls including slab as to give final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per PWD specification and as per the direction of Engineer-In-Charge complete in all leads, lifts and other incidentals. | 122.88 | Per square metre | |
| 86 | 86 | Providing and fixing vitreous china water closet squatting pan (Indian Type W.C. Pan) big pan No 2071 of size 580 x 440mm (five hundred eighty into four hundred forty millimeter) with low lewel PVC Cistren of CERA(earth work, bed concrete, foot rest and trap to be measured and paid for separately) Orrissa Pattern including entire carriage of materials within all leads and lifts as per direction of Engineer-in-Charge. | 11 | Each | |
| 87 | 87 | Providing and fixing vitreous china wash, down water closet (European type W.C. Pan) N o 2061 universal WC of CERA with integral ‘P’ or ‘S’ trap including jointing the trap with soil pipe in cement mortar 1:1 (One Cement: One sand) Seat and cover to be measured and paid for separately) Anglo Indian (Universal closet) including entire carriage of materials within all leads and lifts as per direction of Engineer-in-Charge. | 5 | Each | |
| 88 | 88 | Providing and fixing Orrisa pattern vitreous China water closet squatting pan ( Anglo Indian type W.C.pan)size 580mm (five hundred eighty millimetre) (earth work, bed concrete, foot rest and trap to be measured and paid for separately) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 8 | Each | |
| 89 | 89 | Providing and fixing 100mm (One hundred millimeter) size ‘P’ or ‘S’ trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (one cement : one sand) sand cast iron including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 11 | Each | |
| 90 | 90 | Providing and fixing 10.00 (Ten) litres capacity P.V.C low level flushing cistern of CERA with a pair of G.I.or mild steel brackets complete with fittings such as lead valve less syphone 15mm (fifteen millimeter) nominal size bras ball valve with polythene float C.P. Brass handle unions and coupling for connections with inlet, outlet and overflow pipes, 40mm (forty millimeter) dia C.P. flush bend including cutting holes in walls and making good the same and connection the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 24 | Each | |
| 91 | 91 | Providing and fixing vitreous china wash basin No 1002 of 55x40cm (fifty five into forty centimetre) of CERA with double hole for pillar tap with C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting (Flat back) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 16 | Each | |
| 92 | 92 | Providing and fixing vitreous china pedastal for wash basin No 1108 of CERA complete recessed at the back for the reception of pipes and fittings including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 21 | Each | |
| 93 | 93 | Providing and fixing vitreous china wash basin No 1012 (CANON) of 450x300MM (Four hundred fifty into three hundred milimetre) of CERA with double hole for pillar tap with C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting (Flat back) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 5 | Each | |
| 94 | 94 | Providing and fixing heavy quality stainless steel kitchen sink with C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting 600 x 450 X 150mm (six hundred into four hundred fifty into one hundred fifty millimetre) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 4 | Each | |
| 95 | 95 | Providing and fixing 32mm (Thirty two milimetres) diameters C.P. brass waste ESS-ESS (Heavy duty make ISI marked NO-8931 & 8934) for wash basin or sink. Within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 25 | Each | |
| 96 | 96 | Providing and fixing 32mm (Thirty two milimetres) nominal size diameters rubber plug for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 25 | Each | |
| 97 | 97 | Providing and fixing 32mm (Thirty two milimetres) nominal size diameters M.I. union for wash basin sink, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 25 | Each | |
| 98 | 98 | Providing and fixing 32mm (Thirty two milimetres) nominal size diameters PVC waste pipe for wash basin sink including check nuts, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 25 | Each | |
| 99 | 99 | Providing and fixing 100mm (One hundred milimetres) nominal size diameters CP iron grating of ESS-ESS for nalhni trap complete, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 46 | Each | |
| 100 | 100 | Providing and fixing of jet pressure of ESS-ESS for Europen seat with one meter tube of approved brand and manufacture, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 13 | Each | |
| 101 | 101 | Providing and fixing 600mmx450mm (six hundred millimeter into four hundred fifty millimeter) bevelled edge mirror of superior glass mounted on 6mm (six millimeter) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. screws and washers including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 21 | Each | |
| 102 | 102 | Providing and fixing brass towel rail of Ess- Ess complete with C.P. brass brackets fixed to wooden plugs with C.P. brass brackets fixed to wooden plugs with C.P. brass 600x20mm (Six hundred nto twenty millimetre) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 21 | Each | |
| 103 | 103 | Providing and fixing brass towel rail of Cat No. 4901 hotslier series of Ess- Ess complete with C.P. brass brackets fixed to wooden plugs with C.P. brass brackets fixed to wooden plugs with C.P. brass 750x20mm (Seven hundred fifty nto twenty millimetre) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 7 | Each | |
| 104 | 104 | Providing and fixing 600 x 120mm (Six hundred into one hundred twenty milimetres) glass shelf with C.P. brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 21 | Each | |
| 105 | 105 | Providing and fixing chromium plated brass soap dish of ESS-ESS with C.P. brass brackets fixed to wooden cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 29 | Each | |
| 106 | 106 | Providing and fixing chromium plated brass H923 soap dish with Acrylic Dish hotelier series of ESS-ESS with C.P. brass brackets fixed to wooden cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 7 | Each | |
| 107 | 107 | Providing and fixing 15mm (Fifteen milimetres) diameters C.P. brass bib tap of ESS-ESS with capstan head, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 36 | Each | |
| 108 | 108 | Providing and fixing canealed C.P. brass stop cock of ESS-ESS 15mm (fifteen millimetre) dia (Heavey duty makes ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 106 | Each | |
| 109 | 109 | Providing and fixing C.P. brass pillar tap of ESS-ESS with capstan head 15mm (fifteen millimetre) dia (Heavey duty makes ISI marked No. 8931 & 8934) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 21 | Each | |
| 110 | 110 | Providing and fixing 15 mm (fifteen milimetre) dia PVC connection pipe brass union 450mm (four hundred fifty milimetre) length including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 85 | Each | |
| 111 | 111 | Providing and placing water tank of makes (sintex) having capacity 1000 ( five hundred ) litres each with necessary fitting including over flow pipes scour pipe and ball valve and with cover locking arrangement including providing pads of sizes as required for inlet and outlet and inside painting of good quality all complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 6 | Each | |
| 112 | 112 | Providing and fixing 15mm (fifteen millimetre) C.P. Brass full way valve with wheel of ESS-ESS including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 6 | Each | |
| 113 | 113 | Providing and fixing 15mm (fifteen millimetre) C.P.brass ball valve of ESS-ESS ( Horizontal plunger type) high pressure with copper float nominal bore within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 6 | Each | |
| 114 | 114 | Providing and fixing polythene aluminum polythene ( PE-AL-PE) composite pressure pipe U.V. stabilized with carbon confirming to IS 15450-2004 of KITEC for water supply including clamps at one meter spacing, cutting fixing and making good the wall etc. but excluding the cost of fitting internal work pipe exposed on wall 1216-16 mm (Sixteen milimetre) O.D. complete including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 80 | Per running metre | |
| 115 | 115 | Providing and laying 20mm (Twenty millimeters nominal bore/diameters to galvanized mild steel tubes (medium grade) in tenches including all tube fittings such as nipples, elbows, unions, tees and clamps (earth work trenches paid for seperately) including within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.\n\n | 410 | Per running metre | |
| 116 | 116 | Providing and laying 15mm Fifteen millimeters nominal bore/diameters to galvanized mild steel tubes (medium grade) in tenches including all tube fittings such as nipples, elbows, unions, tees and clamps (earth work trenches paid for seperately) including within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.\n\n | 250 | Per running metre | |
| 117 | 117 | Providing and fixing 75mm (seventy five millimeter) nominal size/diameter sand cast/cast iron spun spigot and socket soil, waste and ventilating pipes (lead caulked joints to be measured and paid for separately) including entire carriage of materials within all leads and lifts as per directions of Engineer-in-Charge.\n\n | 205 | Per running metre | |
| 118 | 118 | Providing and fixing 100mm (one hundred millimeter) nominal size/diameter sand cast/cast iron spun spigot and socket soil, waste and ventilating pipes (lead caulked joints to be measured and paid for separately) including entire carriage of materials within all leads and lifts as per directions of Engineer-in-Charge.\n\n | 205 | Per running metre | |
| 119 | 119 | Providing and fixing 75mm (seventy five millimeter) nominal size/diameter sand cast iron/cast iron holder bat clamps including steel bolts to sand cast iron pipe embedded in and including cement concrete block 100x100x100 mm (One hundred into one hundred into one hundred) of cement concrete 1:2:4 (One cement isto two sand isto four graded stone aggregate 20mm (Twenty millimetre) size) including cost of making holes in wall and making good the wall as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. \n | 228 | Each | |
| 120 | 120 | Providing and fixing 100 mm (one hundred millimeter) nominal size/diameter sand cast iron/cast iron holder bat clamps including steel bolts to sand cast iron pipe embedded in and including cement concrete block 100x100x100 mm (One hundred into one hundred into one hundred) of cement concrete 1:2:4 (One cement isto two sand isto four graded stone aggregate 20mm (Twenty millimetre) size) including cost of making holes in wall and making good the wall as per PWD specification. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. \n | 228 | Each | |
| 121 | 121 | Providing fixing sand 75mm dia (Seventy Fivemillimeter) millimeter) cast iron/cast iron spun fitting and plain bend with ovel access door insertion rubbed washer 3mm (three millimeter) thick bolt etc including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 13 | Each | |
| 122 | 122 | Providing fixing 100mm dia (hundred millimeter) sand cast iron/cast iron spun fitting and plain bend with ovel access door insertion rubbed washer 3mm (three millimeter) thick bolt etc including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 12 | Each | |
| 123 | 123 | Providing fixing 75mm dia (seventy millimeter) sand cast iron/cast iron fitting accessories singal equal branch of required dgree plain bend including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 5 | Each | |
| 124 | 124 | Providing fixing 100mm dia (hundred millimeter) sand cast iron/cast iron fitting accessories singal equal branch of required dgree plain bend including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 5 | Each | |
| 125 | 125 | Providing fixing 75mm dia (seventy millimeter) sand cast iron/cast iron fitting accessories double equal branch of required dgree including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 20 | Each | |
| 126 | 126 | Providing fixing 100mm dia (hundred millimeter)sand cast iron/cast iron fitting accessories double equal branch of required dgree including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 20 | Each | |
| 127 | 127 | Providing fixing 100mm dia (hundred millimeter)sand cast iron/cast iron fitting accessories single unequal branch of required dgree with heel rest bend including entire carriage of material within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 5 | Each | |
| 128 | 128 | Providing fixing75 mm dia (Seventy five millimetre) sand cast/cast iron coller including fittings including laying and fitting within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 115 | Each | |
| 129 | 129 | Providing fixing 100mm dia (hundred millimetre) sand cast/cast iron coller including laying and fitting within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 115 | Each | |
| 130 | 130 | Providing fixing 75mm dia (seventy five millimetre)lead caulked joint to sand cast iron / cast (spun iron) pipe & fittings including testing of joint within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 115 | Each | |
| 131 | 131 | Providing fixing 100mm dia (one hundred millimetre)lead caulked joint to sand cast iron / cast (spun iron) pipe & fittings including testing of joints within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 115 | Each | |
| 132 | 132 | Providing and fixing 110mm x 90mm (one hundred ten into ninty millimetre) nominal size PVC floor trap of self cleaaning design with approved design complete including cost of cutting making good in the work of floor including carriage of materialswithin all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 46 | Each | |
| 133 | 133 | Construction manhole with R.C.C. top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) foundation concrete 1:4:8(One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty milimetres nominal size) inside plastering 15mm (Fifteen milimetres) thick with cement mortar 1:3 (One Cement: three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty milimetres nominal size) finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred milimetres) 500mm(Five hundred milimetres) deep, including C.I. cover with frame (light duty single seal pattern–I) 450x610mm (Four hundred fifty into six hundred and ten milimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 200mm (Two hundred milimetres) thick walls of brick masonry using cement dust clery building brick in cement mortar 1:3 (one cement: three sand) within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 13 | Each | |
| 134 | 134 | Constructing brick masonry chamber for under ground CI inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (one cement : five sand) cover with frame (light duty) 355mm x 610mm internal dimensions total weight of cover with frame to be not less then 38Kg. (weight of cover 23Kg. and weight of frame 15Kg) RCC top slab with 1:2:4 (one cement : two sand : four graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm nominal size) in side plaster 15mm thick with cement mortar 1:3 (one cement : three sand) finished smooth with floating coat of neat cement on wall and bed concrete etc. complete. Inside dimension 455x610x450mm deep single pipe line. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 19 | Each | |
| 135 | 135 | Excavation in drains and channels etc; in earth work in all classification of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturator soil including chiseling or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimeter) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of materials and other incidentals. | 42.19 | Per cubic metre | |
| 136 | 136 | Providing and fixing stoneware pipe gully trap grade\"A\" compete with C.I. gratting brick masonry chamber in cement moratr 1:5 (One cement isto five sand) and water tight C.I. cover with frame of 300x300 mm (Three hundred into three hundred millimetre) size ( inside) the weight of cover to be not less than 4.53 Kg (Four decimal five three kilograms) and frame to be not less than 2.72 kg (Two decimal seven two kilograms) square mouth traps 150mmx100mm (One hundred fifty into one hundred millimetre) size P or R Type complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 75 | Each | |
| 137 | 137 | Providing and laying cement concrete 1:4:8 (One cement: Four sand: Eight graded crushed/broken stone aggregate 40mm (Forty millimere) nominal size) in haunching of stoneware pipes of the 150 mm (One hundred fifty millimetre) internal diameters including concrete for bedding necessary form work and curing complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 150 | Per running metre | |
| 138 | 138 | Providing and laying ( to level or slope) of PVC (D-plast) 110 mm (One hundred ten millimetre) sewer pipe of working pressure not less than 4.5 kg/sqm. (Four decimal five kilogrms per square metre) including filling the joints with approved adhesive complete. The rates are including cost and carriage within all leads and lifts and other incidentals as per PWD specification and entire satisfaction/direction of Engineer-In-Charge. | 210 | Per running metre | |
| 139 | 139 | Providing and fixing H923 CP brass toilet paper holder without lid wall mounted holder series of Ess Ess complete in all respect including within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge | 11 | Each | |
| 140 | 140 | Providing and fixing viterious bowl pattern urinal no 5001 flat back type ( large) of size 430 x 260 x 350 mm (four hundred thirty into two hundred sixty into three hundred fifty ) of CERA including connection the urinal waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured and paid sepertely) | 16 | Each | |
| 141 | 141 | Providing and fixing vitreous china division plate No 5011 of CERA for urinal 600x300mm (six hundred into three hundred millimetre) complete in all respect including within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 12 | Each | |
| 142 | 142 | Providing and fixing Solid Type white plastic sheet (Solid type) and cover for washed on water closet with CP brass hinges and rubber buffers including carriage of materials within all leads, lifts and other incidental charges complete in all respect. | 13 | Each | |
| 143 | 143 | Providing and fixing 5.00 ltr (five liter) capacity Vitreous chaina automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fitting including C.I. or mild steel brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) including within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 16 | Each | |
| 144 | 144 | Providing and fixing 455X610mm( four hundred fifty five by six hundred ten millimeter) light duty rectangular Cast Iron manhole with frame cover weioght 38 kg ( thirty eight kilograme) single seat including within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. | 1 | Each |
AI Tender Summary
Tender Timeline
Mar 12, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedMar 27, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 28, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender