tender for Electrical Works On Turnkey Basis Of Ins Sujata , electrical works ( bilge lighting , various starter panels and control panels servicing ) on turnkey basis of ins sujata ( nr-19 ) : complete scope of work is to be executed ( including spares / material / consumables / components ) as per annexures-a , b , c , d , e & f and finally satisfactory trials to be shown to the shipstaff / hsl / all navy trial agencies . , procurement , replacement and alignment of s / w pump , associated motor , starter and control panel . foundation and system pipes to be modified as per requirement and mounts to be renewed by contractor as per oem recommendation . pump to be proved for design parameters by offering for trials to naval trails agencies and ships staff . note: pump & motor hsl supply . contractror should consider scope only for starter panel as per attached enclosure . , supply and installation of new firemain no 2 . scope of work includes:- note: pump & motor hsl supply . contractror should consider scope only for starter panel as per attached enclosure . firemain no 2 . 27 kw , 415 v , 3 phase , 50 hz . siemens , dl . no . 2072 , removal of existing motor , control panel and associated cabling . , manufacturing of sitting arrangements for motor and control panel . , procurement and installation of new firemain motor and control panel; note: motor hsl supply . contractror should consider scope only for starter panel as per attached enclosure . , procurement and laying of cables as per system manual and wld; note: cable will be supplied by hsl . , stw and serviceability checks to be carried out . , post installation trials to be carried out . defects observed to be rectified . , supply and installation of new bilge ballast no 1 & 2 . scope of work includes:- note: pump & motor hsl supply . contractror should consider scope only for starter panel as per attached enclosure . bilge ballast no 1 & 2 . 27 kw , 415 v , 3 phase , 50 hz . siemens , dlno . 2073 , removal of existing motor , control panel and associated cabling . , manufacturing of sitting arrangements for motor and control panel . , procurement and installation of new bilge ballast motor and control panel . note: motor hsl supply . contractror should consider scope only for starter panel as per attached enclosure . , laying of cables as per system manual and wld . note: cable will be supplied by hsl . , stw and serviceability checks to be carried out . , post installation trials to be carried out . defects observed to be rectified . , procurement of heat resistant cables and new bilge lights along with fittings and installation of the same . note: contractor should quote along with material as per enclosed bp and also scope of work is attached . bilge lighting ( fer , and aer ) . flame proof 15 w or higher type tested marine grade led lights . m / s rayen / mc geoch / m / s . zeal tech dl . no . 2074 , procurement and laying of new heat resistant cables . , procurement and installation of flame proof lights . , procurement and fitment of new control panels for lighting controls . , starter ( 415v , 3ph , 50hz ) : the scope of work as follows: remove the starters from ship and land it to shop floor . complete scope of work and servicing carriedout as per annexure- c & annexure-e; starter to be offered for trials to ss after assembling at shipyard shop floor . fit the starter in ship with earthing cable and take trial with motors . , all talley , components and cables to be removed from starter and starter body to be painted ( 1 coat red oxide & 2 coats smoke grey enamel paint ) including procurement of paint by vendor . , all internal wiring , indication , terminal blocks , push buttons and knobs to be procured and replaced including spares by contractor . , 65 in nos over load relays as per existing capacity to be procured and replaced after calibration and calibration certificate to be provided to ss . , procure and replace the contacts of 65 in nos main contactors ( 415v , 3ph , 50hz ) with 2 no + 2 nc as per existing capacity view old contacts pitted / burnt including spares . , starter ( 415v , 3ph , 50hz ) : the scope of work as follows: remove the starters from ship and land it to shop floor . complete scope of work and servicing carriedout as per annexure- c & annexure-e; starter to be offered for trials to ss after assembling at shipyard shop floor . fit the starter in ship with earthing cable and take trial with motors . , all talley , components and cables to be removed from starter and starter body to be painted ( 1 coat red oxide & 2 coats smoke grey enamel paint ) including procurement of paint by vendor . , all internal wiring , indication , terminal blocks , push buttons and knobs to be procured and replaced by contractor . , over load relay as per existing capacity to be procured and replaced after calibration and calibration certificate to be provided to ss . , vendor to procure and replace the contacts of main contactors ( 415v , 3ph , 50hz ) with 2 no + 2 nc as per existing capacity view old contacts pitted / burnt . , check automatic pressure switch on air reservoir for correct functioning . , check automatic pressure switch on air reservoir for correct functioning . , calibrate lub oil low pressure trip of hp air compressors and forward calibration certificate to ship . quote seperately for renewal , calibrate high temp switch of hp air compressors and forward calibration certificate to ship . quote seperately for renewal , calibrate all instrumentation and safeties including functional test of relief valves . , display to be procured and replaced as per sample . , calibrate fresh water pressure cutout . provide calibration certificate to ship . qty- 01 cut out- 04 bar cut in - 02 bar , inspect all pcbs / electrical parts of control panel . ( all electrical circuit board and soliod vv ) , quote for overhauling / procurement and replacement of injector test kit , emergency stop provision for following fer and aer machinery to be checked and defect if any to be rectified:- ( a ) me l / o st by pp- 02 ( b ) m / e l / o priming pp- 02 ( c ) e / r supply fan- 04 ( d ) e / r exhaust fans- 04 ( e ) l / o purifier- 02 ( f ) fuel oil purifier- 02 ( g ) f / o feed pp- 02 ( h ) l / o transfer pp ( j ) rg l / o st / by pp- 02 ( k ) package a / c in mcr , auto operation of halon system non ops . defect to be rectified . , auto ventilation cutoff non ops , defect to be rectified . , overhauling / defect rectification of existing control panel and laying of damaged cables , control panel . the scope of work as follows: capstan . 415v , 3ph , 50hz dl . no . 2052 . 9 , remove the control panel from ship and shift it to shipyard shop floor . complete servicing carriedout to the satisfaction of ss / hsl / navy trial agencies . control panel to be offered for trials to ss after assembling at shop floor . fit the control panel in ship with earthing strap and take trials with motor . , all talley , components and cable to be removed from starter and starter body to be painted . ( 1 coat red oxide & 2 coats smoke grey enamel paint ) including procurement of paint by vendor . , all internal wiring , indication , terminal blocks , push button , knobs and to be procured an
