Tender For Civil Sor At Bilaspur Ro -Surface dressing of the ground including removing small plants, bushes ,vegetation (dia less than 4) and making surface levelled and disposal of rubbish outside HPCLs premises to an unobjectionable place, as directed by the Engineer in Charge, Excavation for foundation upto required depth below existing ground level up to 1.5m in any tyoe odf soil except hard rock. Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, trenches/plinth beam etccompacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCLs premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete. The measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths, Excavation for foundation upto required in hard rock and excavation shall be done by chiselling / pneumatic drilling or Blasting. Rate to include dressing the sides and bottom, bailing out of water if encountered, shoring, strutting, backfilling after the construction of foundation, compacting by the side of the foundation and disposal of surplus excavated earth within/outside HPCLs premises to an unobjectionable place, as directed by the Engineer in Charge including spreading, watering and compaction, complete . The measurement of the excavation would be based on actual depth of excavation with applicable rate for different depths. EXCAVATION IN HARD ROCK BETWEEN 3 TO 4.5, Providing and laying PCC 1:2:4 using 20 mm and down size graded stone aggregates including machine mixing, providing formwork if required, placing, compacting by hand ramming, mechanical vibrators, curing etc complete, Providing and laying 60 mm average thickness coping in CC 1:2:4 mix using 6 to 12 mm stone aggregate with 40 mm projection on either side of wall with drip mould. Rate to include 20 mm thick plaster in cm 1:4 for fixing of glass pieces including mixing, providing necessary shuttering, compaction and curing. Thickness of coping at the ends shall be 40 mm and 80 mm at centre, Providing , mixing and placing REINFORCEMENT CEMENT CONCRET 1:1.5:3 mix using 20 mm and down size graded crushed aggregate including providing and fixing necessary plywood /steel shuttering , scaffolding, bracing, machine mixing, compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item. Concrete conforming to relevant specifications of IS 456 - Latest Edn. RCC 1:1.5:3 FOR TOP SLAB OF UG TANK, Providing and laying in position specified grade (Ready Mix Concrete) controlled concrete as per approved mix design for sub-structure (i.e. upto ground level icluding pavement ) and shapes using graded metal with size 20 mm and 12.5 mm. including placing, vibrating, compacting, curing etc. complete as per provisions of the relevant IS codes Rate shall be exclusive of the cost of steel reinforcement, which will be paid under a separate item READY MIX CONCRETE (M-25) FOR :RCC D/way/ Culvert slab/Tank bottom raft/tank top slab as per IS-4926, BRICK MASONRY WORKS :Providing and constructing 345 MM THICK brick masonry in foundation and super structure in CM 1:5 using first quality bricks of Class designation 35 (35 KG / SQCM minimum) and conforming to IS-1077-1986 including providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of bricks in water prior to use and curing etc complete as per specifications, Providing and constructing random rubble masonry with good quality stone in CM 1:5 for substructure & superstructure as per IS 1597 part 1, latest edition. Rate to include raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be provided for every square meter of facing , evenly distributed in a staggered pattern. They shall have about 0.03 sqm in face area and shall have a tailing for the full width of masonry upto 600mm.If masonry wall is over 600mm thick, a line of headers (not less than 450mm length) overlapping each other by 150mm shall be laid. Bond stones shall be distinctly marked on its face during construction for verification. Quoin/key/corner stone shall not be less than 0.03 cum in volume. but FOR SUPERSTRUCTURE including scaffolding, Providing and laying dry trap rubble stone soling 230 mm thick including hand packing, filling the interstices with chips, spalls and binding with grit and selected murrum, watering, compacting by power rolling with 8/10 ton roller complete, Supplying , erecting and fixing in position Pre- fabricated steel structures at all elevations for Canopy using structural steel sections ISMB/ISMC/ISA conforming to IS:2062 , including cutting, welding or bolting, supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and applying one coat of Zinc Phosphate Primer before erection, one coat after erection and two coats of synthetic enamel paint as per specification after erection and all materials and labour complete. ( No welding is permitted at site). The rate quoted shall include cost of bolts, nuts, washers, welding and electrodes and any other consumables required for completing the work. Nutbolts shall not be considered for payment.Theoretical wight of steel sections shall be considered for payment, HUME PIPE- Supplying, laying, joining and aligning 1000mm DIA NP4 class RCC Hume pipes conforming to IS-458 Latest Edition below approach road as directed. Rate to include joining with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4 haunching @ 1m c/c , also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the HUME Pipe for pulling cables in future.Test certificates from manufacture shall be submitted and approved by EIC before use.1000 MM DIA, Supplying, laying, joining and aligning RCC Hume pipes conforming to IS-458 Latest Edition below approach road as directed. Rate to include joining with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4 haunching @ 1m c/c , also including cutting, bending & supply and laying of 17 SWG annealed binding wire inside the HUME Pipe for pulling cables in future.Test certificates from manufacture shall be submitted and approved by EIC before use HUME PIPES- 200 MM DIA NP2 CLASS, Providing and fixing Mangalore tilesof 12 mm thick and minimum 230x150 mm size of approved shade and make First quality , free from crack fissures & flakes with straight edges & perfect corners fixed in true line & level as per the design and pattern advised by Engg.-In-Charge and finishing the work in a neat & aesthetic way complete in all respects. Rate to include Teakwood framing structure for holding the tiles in fixed condition, KOTA STONE SKIRING Providing and laying 100mm high x 18mm thick Kota stone skiring on the walls in uniform colour and approved size & pattern including bedding of 20mm thick CM1:3 close jointed & floated with matching cement slurry, curing, polishing to mirror finish with oxalic acid etc., complete, PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat with brush and final coat with Roller) of Plastic Emulsion paint of approved make and shade on all surfaces and heights to give an even shade including primer and compatible putty. Approved Make: Asian/Nitco / Nerolac. General specifications/guidelines given under WHITEWASH item also to be followed, as applicable, Plaster of Paris (POP) Moulding : Providing and fixing moulding of size 3 x 3 in the edge of the wall and the ceiling with necessary hardware, properly finished, all material and labour complete, ALUMINIUM GLAZED DOOR WITH 12MM TOUGHENED GLASS, ALUMINIUM PANELED DOOR, STEEL DOORS, STEEL WINDOWS, MS FAN HOOKS, INDIAN WATER CLOSET Supplying and fixing pastel coloured vitreous china Orissa Pan type water closet comprising of the the following accessories including cutting and making good the walls & floors wherever required complete as directed by Engineer In Charge. A)Coloured (pastel colour) viterous china 580 mm orissa pan water closet of Hinduatn sanitaryware or any equivalent make with P or S trap. B) 10 litres capacity hi-grade engineering plastic low level flushing cistern of matching colour Parry Slimline make model 8068 or approved equivalent make with necessary fittings , brackets , screws etc. all complete . C) 32 mm PVC flush pipe 10 Kg/Sqcm quality of approved lengt with necessary fittings ,clamps etc. D) 15 mm NB CP inlet connections with brass union at the ends E) 15 mm NB brass angle valve as per ISI of approved brand as per the direction of Engineer In Charge F) WC connector with neoprene rubber . Approved Equiv. - Hindware Cat. 20004 with equivalent low level cistern, URINAL DIVISION PLATE Providing and fixing 1200 x 450 x 18 mm size granite partition plate between urinals including cutting masonary/concrete surface to required size, fixing the division plate on the ceramic tiles by means of SS clamps, nuts & bolts, polishing all exposed surface etc all complete as directed by Engineer In Charge. (Refer attached Drawing), Providing and fixing in position CP sensor Faucet of 51071 Jaquar make as per the drawing. The item includes all necessary fittings, accessessories etc. complete as per the direction of Engineer In Charge, Providing, fixing and commissioning fully automatic shoe polish machine with electronic eye (infra red sensor) having both separate black and brown rollers. The machine shall start automatically when shoe is placed and automatically stop. Rate includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampere load of instrument. Care shall be taken so that finishing is not damaged while installation. Make - Technocrats (Model Executive Deluxe), Providing and fixing beveled edge mirror of superior glass of 5.5 mm thick of BELGIUM GLASS or any other equivalent make, craft paper, 3mm thick felt backing or 6 mm asbestos sheet. Teak Wood beads 25x40 mm as per approved shape/drawing allround and fixed with wooden plugs with CP brass screws and cup washers etc all complete as directed by Engg.-In-Charge.(Refer attached Drawing), SUPPLY AND LAYING OF GI LINE OF SIZE 1.5 TO BE LAID IN THREADED CONNECTION FOR TANK 11,12,13,14 MANIFOLD, GULLY TRAP WITH CHAMBER Providing and fixing square mouth gully trap including constructing 300 X 300 MM internal size brick masonary chamber with 230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat cement finish, Medium duty CI cover with frame etc. complete, Providing and laying point wiring in concealed conduits for the following points using specified 1100V grade PVC insulated, FRLS multistranded 3 x 1.5 sqmm copper conductor wires. Rate to include supplying, laying and securing in position in roof slabs and brick walls or concrete columns 25 mm dia rigid PVC conduits (Conforming to IS 9537:Part 3: 1983) of approved make with necessary accessories and junction boxes/pull boxes. Providing and fixing in the brick walls flush type metal switch boxes of approved make shade and sufficient size to accommodate all 6A Modular switches / 3 pin socket, screws, holders. ceiling roses and the fan regulator wherever required. Rate to include wall chasing and rough plastering. Providing and fixing single pole 6 A socket modular plate switches of approved MK or ANCHOR ROMA/HAVELLS /FINOLEX/CRABTREE/SSK make and of approved colour . One switch shall be provided for each light and fan point. Rate also to include providing main circuit wiring from DB to switch boards with 2 runs of 2.5 sqmm copper wire and 1 run of 1.5 sqmm through PVC conduit. also All wires shall be conforming to IS 694:1990. but for 6A socket controlled by one 6A switch on the same lighting board, Supply, laying , and commissioning of wiring using following sizes of PVC insulated , FRLS, unsheathed, multistrand copper wire drawn in PVC conduits. Rate to include supply of 16 GI fish wire, conduits & accessories, wiring, terminations etc complete. All wires shall be conforming to IS 694:1990 and PVC conduits to conforming to IS 9537:Part 3: 1983 -- Supply and laying through conduit FRLS multistranded PVC insulated (1100V) copper wire conforming to IS 694:1990 and of size 1.5 sqmm including termination etc. all complete. PVC Conduits to be paid for separately as per relevant items, Supply, fixing and commissioning of Exhaust fans of following dia including bird louvers, frame works and other civil works like chipping and making the surface good etc EXHAUST FANS 230MM DIA, Supply,Delivery and Installation of Wall Mounted Panel Board as per the enclosed Single Line Diagram for Retail Outlets( Refer Attached Drg). Party has to supply the panel after approval of the G.A. Supply,Delivery and Installation of Wall Mounted Panel Board as per the enclosed Single Line Diagram for Retail Outlets( Refer Attached Drg). Party has to supply the panel after approval of the G.A. by HPCL. The panel is to be provided with the following and made out of 16 SWG CRCA sheet steel with gland plate made of 14 SWG CRCA with 100 A TPN copper bus bars, interconnections, earthing, powder coating etc complete as per the approved make of materials:Incomer : 2 no. 63A FPC MCB for DG and EB, 1 no 63A 4 pole on load change over switch 1 no. voltmeter with selector switch, 1 no. ammeter with selector switch and with CT (60/5A) 3 nos, 2 set of phase indicating lamp(RYB), Control Fuse with base.Outgoings: 4 nos. 32 A TPC MCB, 1 no. 32 A TP D MCB, 9 nos. 20 A DPC MCB, 1 no. 40 A DP ELCB 30 mA, 15 nos. 10 A SPB MCB, 2 nos. 10 A DPB MCB ,7 nos. 6 A SPBMCB, 1 no. 40 A FP MCB with KMS meter. Capacitor: 10 KVAR. Connections for the outgoings MCBs from the bus bar to be distributed from the R, Y & B phases as indicated in the SLD. Rate to include supply of Copper bus Bar of 100 amps rating, End termination blocks of sufficient quantity for the above cable terminations but not less than 32A connector - 4 nos, 16 A connectors - 50 nos. Input side cable chamber to have 4 nos. of cable entry holes with dummy caps, on the top and bottom respectively (total 8 holes), of 28 mm dia for installation of NFLP glands. Output side cable chamber to have 25 nos. of cable exit holes with dummy caps, on the top and bottom respectively (total 50 holes), of 19mm dia for installation of NFLP glands. The panel should have provision for earthing connection. The fixing lugs of length 6, bent in the shape of L for mounting the panel on the wall etc. complete. Rate includes supply of necessary wiring accessories, busbar connectors etc complete. Panel size to be of minimum 1700mm(L) x 2000 mm (H) X250 mm (D) ( Refer attached GA Drg) Note : TPI of panels at factory as per the approved QAP of HPCL by TPI vendors ( HPCL shall specify third party inspection(TPI) agencies to the vendor) to be done as per the requirement of the HPCL .Rate of MV panel includes the Cost of TPI and Transportation to the site and inclusive all taxes, Supply and fixing Philips make Cat. QVF 135 hoarding light fixture (IP65) with Metal Halide MHN-TD 70W lamp, control gear box, light weight corrosionresistant pressure die cast housing with universal mounting bracket, all accessories energy efficient copper ballast, heat resistant toughened glass cover, electronic ignitor, reflector, power factor improvement capacitor etc. complete. Approved equivalent Crompton make Cat. TH 6 MH(DE). The job includes fixing the street light fixtures and wiring as approved, Supply , installation and commissioning of 1 phase AIR cooled balanced / unbalanced load servo controlled voltage stabiliser of rating 10 KVA (Make - Logicstat / Blue bird / Bhurji / Techno Vision /Numeric or HPCL approved make) including auto / manual control, overload trip relay, low / high voltage cut-off, single phase protector, cost of oil. Rate includes making input and output connection but excludes supply of necessary cables, lugs and clamping. Party to furnish manufacturers test certificate alongwith supply and provide warranty/gaurantte for a period of one from the date of installation. Detailed specifications are as under: Specifications 1 Phase1. Input Voltage 170 - 270VAC2. Output Voltage 230 VAC3. Operating frequency 50 HZ4. Output Voltage Regulation +/- 1%5. Response time < 3 msecs6. Rate of Correction 12 to 60 V / Sec7. Efficiency > 98%8. Wave form Distortion Nil9. Effect on Power Factor Nil10. Operating Temperature 10 - 60 Degree C11. Duty of operation Continuous at 100%12. Cooling Air Cooling PROTECTIONSUNDER / OVER VOLTAGE REQUIREDOver Load Protection MCBINDICATIONMains On RequiredUnder/Over Voltage RequiredVoltmeter 0 - 300 VACAMP meter OptionalAlarm Optional, Supply and laying of 80mm thick grey pavers in line and level and approved pattern and shape, as per attached specifications. The job includes supplying and laying sand bedding, compacting using plate vibrator, all material and labour complete. Pavers will be laid in specified pattern. Plan of laying will be developed by the contractor and prior approval of EIC will be taken before commencement of laying. The pavers supplied should qualify min comp. strength of 47.2MPa and should conform to IS:15658:2006. The party shall have to produce manufacturers certification on the paver qualifying criteria stated in IS-15658 and limits specified in the attached specification before the pavers are sited. HPCL reserves the right to do random sampling and testing as per IS-15658:2006 to assess manufacturers certification on qualifying norms specified in the attached specification. The testing charges, if samples qualify, shall be borne by HPCL, else shall be borne by the party.(Refer attached Drawing), Transportation of DUs to site including loading, unloading etc. Complete upto 50KM from the sourceThe quantity will be calculated per trip upto maximum of carrying 5 pumps per trip, Supplying & Laying 40MM Dia Heavy-duty C Class MS Steel ERW Welded P/L ( TATA/Zenith/JINDAL make) Conforming to IS 1239 (part I) - latest edition to the required slope & alignment with heavy duty MS fittings like elbows, sockets,unions , tees etc. including doping pipe line with 3 coats of Shalimastic HD THIXOTROPIC of STP cold applied anti corrosive treatment after preparing the surface as per manufacturer specifications. The joints are to be made leak proof. The P/L which would laid aboveground shall be painted with two coats of synthetic enamel over two coats of Zinc Chromate primer of approved quality and shade. The pipeline shall be tested at a pressure of 5Kg / sqcm. Pipe dia as 80MM DIA, Supplying & fixing 75 mm dia Brass coupling for fill point with required threads complete, INSTALLATION OF NEW HIGHLY POLISHED MARINE GRADE STAINLESS STEEL HAND RAIL. THE RAILING SHALL HAVE WALL MOUNTED SUPPORT AT EACH 3 FEET INTERVAL(APRROX.) AND A STURDY VERTICAL SUPPORTS AT REGULAR INTERVAL OF AT LEAST 2000 MM ALONG THE RUN ON BOTH SIDE OF THE STAIR CASE. THE HANDRAILS SHOULD BE MADE OF A CIRCULAR STAINLESS STEEL SECTION USING 50 MM DIAMETER (2” DIA) POSTS, AND 50MM DIAMETER TOP RAILS. THE THICKNESS OF THE STAINLESS STEEL SHOULD BE AT LEAST 2MM. TOTAL RUN FOR THE ENTIRE STAIRCASE OF THE BUILDING IS APPROXIMATELY 110 MTRS ON EACH SIDE.TOP OF RAILING SHOULD BE 48” (1200CM) FROM FLOOR OR GRADE LEVEL. THE RAILING FOOTINGS MUST BE DRILLED AND FIXED INTO THE BASE FOUNDATIONS USING APPROPRIATE STAINLESS STEEL FIXTURES OR MOUNTING BOLTS.THE GRADE OF THE STAINLESS STILL USED SHALL BE 304DETAILS OF 304 STAINLESS STEEL STAIR HAND RAIL HANDRAIL BRACKET HOLDER FOR SUPPORT MATERIAL: STAINLESS STEEL (GRADE 304)BASE DIAMETER: APPROX. 5.3CM/ 2.09RAIL MOUNTING PLATE SIZE: APPROX. 4.6X3.1CM/ 1.81X1.22HEIGHT: APPROX. 6CM/ 2.36THE ITEM INCLUDES ALL NECESSARY ACCESSORIES AS MAY BE REQUIRED., PROVIDING AND WELDING AND LAYING 32 MM DIAMETER MEDIUM MILD STEEL PIPE RAILING FOR SUPPORT HANDLES, etc.
