| 1 | 1 | working charges and cost of materials | BI01010001010000000000000515BI0100001112 | | |
|---|
| 2 | 1.01 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidatingeach deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :All kinds of soil (Ref. Item No. 2.10.1 of DSR) | BI01010001010000000000000515BI0100001113 | 18 | cum |
|---|
| 3 | 1.02 | Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth not exceeding 1.5m | BI01010001010000000000000515BI0100001114 | 10.5 | sqm |
|---|
| 4 | 1.03 | Bailing out water with 5 HP engine and pumpset including conveyance to the site, errection, dismantling and taking back of engine and pump, cost of fuel lubricating oil and other stores pay of staff etc. complete.NEW DATA (Prepared based on PHED SDB - Item No.1070 | BI01010001010000000000000515BI0100001115 | 37.3 | Kwh |
|---|
| 5 | 1.04 | Dismantling of C. I sluice valve including stacking of useful materials within a lead of 50 metres.Above 150 mm diameter | BI01010001010000000000000515BI0100001116 | 1 | Nos |
|---|
| 6 | 1.05 | Cutting of 200 mm AC pipes of all classes diametrically, the cut being diametrically perpenticular to the axis of pipe and smoothening of the cut ends etc complete.\"(Ref. No. 1103(5) of Technical Circular)\" | BI01010001010000000000000515BI0100001117 | 2 | No |
|---|
| 7 | 1.06 | Jointing 200 mm A. C. pipes laid to lines and levels in the trenches using C. I. detachable or any available type of joints after cleaning the ends, centering the pipes inserting the joints and tightening including conveying the materials within initial lead and other sundries etc. complete to make a water tight joint capable to withstand the required pressure (excluding cost of CID Joint).\"(Ref. No. 676, PHED Data Book) \" | BI01010001010000000000000515BI0100001118 | 5 | joint |
|---|
| 8 | 1.07 | Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 200mm. | BI01010001010000000000000515BI0100001119 | 2 | No |
|---|
| 9 | 1.08 | Conveying and fixing C.I. sluice valves (with cap) by providing complete with bolts, nuts, rubber insertions etc. excluding the cost of valve (the tail pieces if required will be paid separately) : 200 mm diameter. Class II\" Data derived from item no.18.31.4.2of DAR | BI01010001010000000000000515BI0100001120 | 2 | Nos |
|---|
| 10 | 1.09 | Cutting of 400 mm AC pipes of all classes diametrically, the cut being diametrically perpenticular to the axis of pipe and smoothening of the cut ends etc complete.\"(Ref. No. 1103(9) of Technical Circular 21-07-95)\" | BI01010001010000000000000515BI0100001121 | 2 | No |
|---|
| 11 | 1.1 | Jointing 400 mm A. C. pipes laid to lines and levels in the trenches using C. I. detachable or any available type of joints after cleaning the ends, centering the pipes inserting the joints and tightening including conveying the materials within initial lead and other sundries etc. complete to make a water tight joint capable to withstand the required pressure(excluding cost of CID Joint).\"(Ref. No. 679(2) of T.C dt.07.09.1994)\" | BI01010001010000000000000515BI0100001122 | 2 | joint |
|---|
| 12 | 1.11 | \"Conveying and fixing C.I. sluice valves (with cap) by providing complete with bolts, nuts, rubber insertions etc. excluding the cost of valve (the tail pieces if required will be paid separately) :400 mm diameter. Class I\"Observed Data derived from item no.18.31.of DAR | BI01010001010000000000000515BI0100001123 | 1 | Nos |
|---|
| 13 | 1.12 | Supply of 200mm CID joint | BI01010001010000000000000515BI0100001124 | 10 | set |
|---|
| 14 | 1.13 | Fabricating and supplying 200X200X200 mm MS Tee ( plain at all ends) using 8mm thick MS plate including all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete | BI01010001010000000000000515BI0100001125 | 1 | No |
|---|
| 15 | 1.14 | Fabricating and supplying 400X400X200 mm MS Tee using 8mm thick MS plate including cost of flanges suitable for 400mm and 200mm MS pipe made out of 12mm thick MS plate ( plain at 400 mm one end and flanged at other end of 400 mm and 200 mm ends) including all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete | BI01010001010000000000000515BI0100001126 | 1 | No |
|---|
| 16 | 1.15 | Fabricating and supplying 400 mm MS tail piece using 8mm thick MS plate incuding cost of 12mm thick MS plate and all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete | BI01010001010000000000000515BI0100001127 | 1 | No |
|---|
| 17 | 1.16 | Fabricating and supplying 400 mm MS column pipe all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete | BI01010001010000000000000515BI0100001128 | 1 | No |
|---|
| 18 | 1.17 | Supply of 400mm Mechanical collar | BI01010001010000000000000515BI0100001129 | 2 | No |
|---|
| 19 | 1.18 | Supplying and fixing 400mm MS flange made out of 12 mm thick MS plate including welding to the pipe and all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. completed | BI01010001010000000000000515BI0100001130 | 2 | No |
|---|
| 20 | 1.19 | Engaging Fitter ( grade 1) | BI01010001010000000000000515BI0100001131 | 3 | Day |
|---|
