||Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenched or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kind of soil.
||Supplying and filling in plinth, under floor, foundation etc with sand (fine) from local quarry with all lifts including spreading in horizontal layers watering grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.
||Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 fine sand : 6 graded stone aggregate 20 mm nominal size).
||First class brick work in foundation and plinth including cost of all materials as required complete. In cement mortar 1:4 (1 cement : 4 fine sand).
||Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete. In cement mortar 1:4 (1 cement : 4 fine sand).
||12 mm cement plaster of mix. In cement mortar 1:4 (1 cement : 4 fine sand) including neat cement punning.
||Providing and laying cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry roundaing of edges and strips etc complete. 40 mm thick with 20 mm stone aggregate.
||Supply and installation of pre painted Galvalme sheets (size shae and pitch of corrugation as approved by Engineer In Charge) in 550 mpa steel grade, made out of cold rolled steel coated with Znic Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM A924/A92M, alloy coating AZ150/AZ100, colour coated with high quality polyester coating top coated of modified polyester of 20 micron, back side coat of 5 micron having epoxy primer coat of 5 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 mtr or as desired by Engineer In Charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal or with polymer coated J or L hookes, bolts and nuts 8 mm diameter with bitumen and G.I limpet washers or with G.I limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surface excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thickness.
||Supply and installation of pre painted Galvalume sheets roofing accessories in 550 mpa steel grade, made out of cold rolled steel coated with Znic - Aluminium alloy coating of 43.5% Zn 55% Al and 1.5% silicon confirming to ASTM A 792/A782M ASTM A90/A90M , ASTM AS 1937, ASTM A924 /A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified poyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling / self tapping screws with EPDM seal or with polymer coated I or L hooks, bolts and nuts G.I seam bolts and nuts G.I palin and bitumen wishers complete for Ridges / Vally / Gutter / Flashing of width 610 mm thickness.
||Steel work welded in built up section / framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc complete as required. In grating, frames, guard bar railing, brackets gates and similar works all complete.
||Providing and fixing hard drawn steel wire fabric 75 x 25 mm mesh of weight not less tan 7.75 Kg per sqm to window frames etc including 62 x 19 mm beading of Gamair wood.
||Panting with synthetic enamel paint (two or more coats) of required colour of approved brand and manufacture on new work to give an even shade (Payment shall be made after submission of Test Certificate issued by the Manufacturer).
||Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breacking clods watering, rolling each layer with 1/2 tonne roller or wooden or steel rammers, and rolling every 3rd and top most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks and guide banks or filling up ground depressions lead upto 50 mm and lift upto 1.5 mm. All kind of soil.
||Steel work in built up tubular (round, sque or rectangular hollow tubes etc) trusses etc including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete. Hot finished welded type tubes.
||Providing and fixing M.S round holding down bolts with nuts and wahser plates complete as per standard design.