Supply, Testing, Installation And Commissioning Of Different Instruments, Equipment And Shop Machineries Of Fitter Trade Courses:-1. Compressor Unit Suitable For Pressure: 8 Bar, Delivery: 50 Lpm ( Or More ) , Reservoir Capacity: 24 Liters ( Or More ) , 230V, 50 Hz, With Pressure Regulator And Water Separator 2. Pneumatic Trainer Kit, Each Consisting Of The Following Matching Components And Accessories: I. Single Acting Cylinder: Max. Stroke Length 50 Mm, Bore Dia 20Mm --1 No Ii. Double Acting Cylinder: Max. Stroke Length 100 Mm, Bore Dia 20 Mm, Magnetic Type --1 No Iii. 3 / 2-Way Valve: Manually-Actuated, Normally Closed----2 Nos Iv. 3 / 2-Way Valve: Pneumatically-Actuated, Spring Return --1 No V. One-Way Flow Control Valve----2 Nos Vi. 5 / 2-Way Valve: With Manually-Operated Switch-- 1 No Vii. 5 / 2-Way Valve: Pneumatically-Actuated, Spring Return-- 1 No Viii. 5 / 2-Way Pneumatic Actuated Valve: Double Pilot --1 No Ix. 3 / 2-Way Roller Lever Valve: Direct Actuation Normally Closed--2 Nos X. Shuttle Valve ( Or ) --1 No Xi. Two-Pressure Valve ( And ) --1 No Xii. Pressure Gauge 0-16 Bar--1 No Xiii. Manifold With Self-Closing Nrv, 6-Way--1 No Xiv. Pushbutton Station For Electrical Signal Input With 3 Illuminated Momentary-Contact Switches ( 1 No + 1 Nc ) And 1 Illuminated Maintained-Contact Switch ( 1 No + 1 Nc ) , Contact Load 2A --1 No Xv.Relay Station With 3 Ralays Each With 4 Contact Sets ( 3No+1Nc Or Change-Over Type ) , 5 A--1 No Xvi. 3 / 2-Way Single Solenoid Valve With Led--1 No Xvii.5 / 2-Way Single Solenoid Valve With Manual Override And Led--1 No Xviii. 5 / 2-Way Double Solenoid Valve With Manual Override And Led--1 No Xix. Power Supply Unit, Input Voltage 85 – 265 V Ac, Output Voltage: 24 V Dc, Output Current: Max. 4.5 A, Short-Circuit-Proof.--1 No Xx.Profile Plate, Anodized Aluminum 1100X700 Mm, With Carriers, Mounting Frames And Mounting Accessories ( To Be Fitted Onto The Pneumatic Workstation ) --1Set 3. Pneumatic Workstation With 40 Square Mm Aluminum Profile Legs, Wooden Work Surface, And One Pedestal Drawer Unit Having 5 Drawers, Each With Handles And Individual Locks, On Metallic Full Panel Drawer Slide: ( 1 ) Work Table – Size ( Approx. ) L1200mmxw900mmxh900mm, With Four Castor Wheels Including Two Lockable Wheels At The Front Side, ( 2 ) Drawer – Size ( Approx. ) – L460mmxw495mm Xh158mm Each, And Overall Size Of Drawer Unit ( Approx. ) -L470mmxw495mmxh825mm And ( 3 ) Drawer Slide Height ( Approx. ) 85Mm. 4. Carrier For Mounting Components, Such As Pb & Relay Boxes 5. Cut Section Model For Pneumatic Components 6. Hydraulic Trainer Kit, Each Consisting Of The Following Matching Components And Accessories: I. Hydraulic Power Pack -- 1 No. With ( 1 ) External Gear Pump Having A Delivery Rate Of 2.5 Lpm, ( Approx. ) @ 1400 Rpm Operating Pressure 60 Bar, Coupled To A Single-Phase Ac Motor ( 230 V Ac ) Having Start Capacitor And On / Off Switch And Overload Protection, ( 2 ) Pressure Relief Valve Adjustable From 0 – 60 Bar, ( 3 ) Oil Reservoir, ≥5 Litres Capacity Having Sight Glass, Drain Screw, Air Filter, And P And T Ports. Ii. Pressure Relief Valve: Pilot-Operated -- 1 No. Iii. Drip Tray, Steel: Size 1160 Mm X 760 Mm. -- 1 No. Iv. Pressure Gauge: Glycerin-Damped, Indication Range Of: 0 – 100 Bar -- 1 No. V. Four-Way Distributor With Five Ports, Equipped With A Pressure Gauge-- 1 No. Vi. Double Acting Hydraulic Cylinder With A Control Cam, Piston Diameter16 Mm, Piston Rod Diameter10 Mm, Stroke Length 200 Mm. -- 1 No. Vii. Suitable Weight For Vertical Loading Of Hydraulic Cylinder -- 1 No. Viii. Mounting Kit For Weight For Realizing Pulling And Pushing Load. -- 1 No. Ix. 3 / 2-Way Directional Control Valve With Hand Lever Actuation. -- 1 No. X. 4 / 2-Way Directional Control Valve With Hand Lever Actuation. -- 1 No. Xi. 4 / 3-Way Directional Control Valve Closed-Centre Position, With Hand Lever Actuation. -- 1 No. Xii. Non-Return Valve. -- 1 No. Xiii. Pilot-Operated Check Valve Pilot To Open. -- 1 No. Xiv. One-Way Flow Control Valve With Integrated Check Valve. -- 1 No. Xv. T-Connector With Self Sealing Coupling Nipples ( 2 Nos. ) And Quick Coupling Socket ( 1 No. ) .--2 Nos. Xvi. Profile Plate, Anodized Aluminum, 1100X700 Mm, With Carriers, Mounting Frames And Mounting Accessories ( To Be Fitted Onto The Hydraulic Workstation ) --1 Set 7. Hydraulic Workstation With 40 Square Mm Aluminium Profile Legs, Wooden Work Surface, And One Pedestal Drawer Unit Having 5 Drawers, Each With Handles And Individual Locks, On Metallic Full Panel Drawer Slide: ( 1 ) Work Table – Size ( Approx. ) L1200mmxw900mmxh900mm, With Four Castor Wheels Including Two Lockable Wheels At The Front Side, ( 2 ) Drawer – Size ( Approx. ) – L460mmxw495mm Xh158mm Each, And Overall Size Of Drawer Unit ( Approx. ) - L470mmxw495mmxh825mm And ( 3 ) Drawer Slide Height ( Approx. ) 85Mm. 8. Cut-Section Models For Hydraulic Components
