Construction Of Dr . B . R . Ambedkar Bhawan At Gohpur Sub Division
Tender Value
1.76 Crore
Estimated cost
Bid Submission
15 Feb 2020
0 days left
EMD
88.12 Lakhs
Bank guarantee accepted
Document Fee
5500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Auction
Location / State
Gohpur → Assam
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Dr . B . R . Ambedkar Bhawan At Gohpur Sub Division
BOQ
| Name of Work: Construction of Dr. B. R. Ambedkar Bhawan at Gohpur | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Civil Works | Head 1 | ||
| 2 | 2 | Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.\n(A) Up to a depth of 2.00m below the existing ground level.\n(a) In ordinary soil | item 1 | 300 | Cum |
| 3 | 3 | Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.\n(a) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m | item 2 | 105 | Cum |
| 4 | 4 | Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.\n(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading. | item 3 | 35 | Cum |
| 5 | 5 | Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid sepaAPWD Rately).\n(a) In prop 1cement: 3 sand :6 coarse aggregate by volume | item 4 | 13 | Cum |
| 6 | 6 | Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. \nc) 100mm thick | item 5 | 250 | Cum |
| 7 | 7 | Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg. of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. | item 6 | 40 | Sqm |
| 8 | 8 | Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid sepaAPWD Rately) \n(I) Using Mixer Machine\n(A) In substructure up to plinth level\nFoundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.\nN) Without using admixture, plasticiser\n i) M20 Grade Prop 1:1.5:3 | item 7 | 54 | Cum |
| 9 | 9 | Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid sepaAPWD Rately) \n(I) Using Mixer Machine\n(A) In substructure up to plinth level\nFoundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.\nN) Without using admixture, plasticiser\n i) Walls (thickness not less than 100mm) including attached pillasters, buttresses, plinth and string course etc. | item 8 | 80 | Cum |
| 10 | 10 | Extra over item Nos. 2.2.1 (I) (B), above for each subsequent floor or part thereof above the 1st floor level. | item 9 | 20 | Cum |
| 11 | 11 | Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:\nFoundation, footings, bases of columns, pile cap, raft and mass concrete works etc.\n(b) Using 25mm thick plank | item 10 | 98 | Sqm |
| 12 | 12 | Sides of tie beams, grade beams etc. at or below ground level.\n(b) Using 25mm thick plank | item 11 | 145 | Sqm |
| 13 | 13 | Columns, Pillars, Posts & Strut\n(a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face\n(ii) Using 25mm thick plank | item 12 | 165 | Sqm |
| 14 | 14 | Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties.\n(a) For depth not exceeding 1.0M.\n(ii) Using 25mm thick plank | item 13 | 372 | Sqm |
| 15 | 15 | Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like.\n(a) Floors etc. upto 200mm in thickness.\n(ii) Using 25mm thick plank | item 14 | 245 | Sqm |
| 16 | 16 | Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank) | item 15 | 24 | Sqm |
| 17 | 17 | Extra for each subsequent floor or part thereof above the First Floor level as mentioned in item no. 3.1.1 & 3.1.3(b). | item 16 | 217 | Sqm |
| 18 | 18 | Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.\n(I) In Sub-structure upto plinth level including dewatering if necessary\n(b) In proportion 1:4. | item 17 | 27 | Cum |
| 19 | 19 | 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid sepaAPWD Rately) \n(A) 112mm thick brick wall\n(a) In cement mortar in proportion 1:4. \n(1 cement:4 sand) | item 18 | 685 | Sqm |
| 20 | 20 | Extra for brick walling for each subsequent floor or part thereof above the 1st floor level.\n(a) 112mm thick brick/ R.B wall | item 19 | 29.09 | Sqm |
| 21 | 21 | Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. \n(a) With sal wood | item 20 | 1 | Cum |
| 22 | 22 | Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. \nb) Non decorative type and block board core.\n(ii) 35 mm thick . | item 21 | 37 | Sqm |
| 23 | 23 | Providing barge board of size 200mm x 20mm with 1st class local Hollock/ Bonsum timber including fitting and fixing with necessary wood screws etc. complete. | item 22 | 66 | RM |
| 24 | 24 | Providing, fitting and fixing PVC door frame of Duroplast make DPF-5060 make suitable for DPS-3720 made from extruded PVC multichamber hollow section having dimensions of 50mmx60mm (Toletance + 1mm). Horizontal and vertical sections shall be joined by steel screws after inserting M.S. tubular rectangular galvanised L-shaped brackets of size 100mmx100mm or plastic brackets of size 75mmx75mm with metred cut at the corners. Hinge side of the frame shall be reinforced with M.S.Tubular section of size 40mmx20mm. The frame will be fixed to the column/ stiffner/ wall with the help of 3 nos 75mm long and 4mm dia steel screws and expandable fastners on each side of the door frame complete in all respects as sepcified and directed at all levels. | item 23 | 65 | RM |
| 25 | 25 | Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid sepeAPWD Rately)\nb) 29mm thick | item 24 | 21 | Sqm |
| 26 | 26 | Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.\n(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the APWD Rate) (Upto 1st floor level) \na) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL\n(ii)Super Ductile (SD) TMT reinforcement bars | item 25 | 186 | Qtl |
| 27 | 27 | Extra over item 18.1.1(a,b,c) for each subsequent floor or part thereof above first floor level. | item 26 | 42 | Qtl |
| 28 | 28 | Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws.\nI . Plain grill\n(c) Fixed to Brickwork/P.C.C/R.C.C. | item 27 | 370 | Qtl |
| 29 | 29 | Providing fitting, hoisting and fixing of roof trusses including purlins fabricated using MS circular hollow section conforming to relevant I.S. code, as per approved design and drawings including providing M.S. cleats, base plates, bolts and nuts and one coat of red oxide Zinc Chromate primer and two coats of approved enamel paints complete including fitting necessary cleats etc. for fixing ceiling joists as per design and drawing as directed. \na) TATA make Circular Hollow section- CHS of Grade YST-310 conforming to I.S. Specification : 1161-1998 | item 28 | 40 | Qtl |
| 30 | 30 | Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department).\nExecutive range\nSomany/ Orient/Nitco/Asian Make\nOf size 300mmx300mm and above | item 29 | 130 | Sqm |
| 31 | 31 | roviding VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department)\na) Normal range \nSomany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make\nii) Of size 600mmx600mm and above | item 30 | 364 | Sqm |
| 32 | 32 | Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed.\n(A) CERAMIC\ni)Normal range (Sizes 300 mm x 300mm and above)\n (a)Orient made: Galaxy Brown, Galaxy creama, Galaxy Pink, Galaxy Green, Pulsar Beige, Pulsar Blue, Pulsar Dove, Pulsar Pink, Burj Brown, Burj Green, Burj Slate | item 31 | 50.3 | Sqm |
| 33 | 33 | 18 mm thick marble stone tiles in flooring including risers and treads of steps, skirting, dado, walls, pillars laid with 10 mm thick base of cement plaster in prop.1:3 ( I cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing complete with marble tiles of specified quality and shade at all levels.\n(a) With 18mm thick marble stone tiles of size 600mm x 600 mm\n(iii) Kumari Marble | item 32 | 38 | Sqm |
| 34 | 34 | 10 mm thick Cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed.\na) In cement mortar 1:3 | item 33 | 275 | Sqm |
| 35 | 35 | 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. \nA) On rough side\na) In cement mortar 1:3 | item 34 | 330 | Sqm |
| 36 | 36 | 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. \nB) On fair side\nb) In cement mortar 1:4 | item 35 | 330 | Sqm |
| 37 | 37 | 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. \nA) On rough side (backing coat 15 mm and finishing coat 5mm thick)\nb) In cement mortar 1:4 | item 36 | 115 | Sqm |
| 38 | 38 | 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. \nB) On fair side (backing coat 10 mm and finishing coat 10mm thick)\nb) In cement mortar 1:4 | item 37 | 115 | Sqm |
| 39 | 39 | 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. \nA) On rough side (backing coat 15 mm and finishing coat 5mm thick)\nb) In cement mortar 1:4 | item 38 | 205 | Sqm |
| 40 | 40 | 20 mm thick Cement plaster in two coats on single or half brick walls for interior plastering up to 1st floor level including arises, internal rounded angles,chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth including curing complete as directed. \nB) On fair side (backing coat 10 mm and finishing coat 10mm thick)\nb) In cement mortar 1:4\n | item 39 | 200 | Sqm |
| 41 | 41 | Extra over item no 6.2.1 to 6.2.3 for providing and mixing water proofing materials in cement mortar in prop as recommended by the manufacturer including curing complete as directed.\nii) 15 mm thick plaster\nb) In cement mortar 1:4 | item 40 | 275 | Sqm |
| 42 | 42 | Extra over item no 6.2.1to 6.2.3 for interior plastering above 1st floor level for every addl floor or part thereof including curing complete as directed.\nb) On two coat plaster | item 41 | 365 | Sqm |
| 43 | 43 | Providing two coats of J.K Wall Putty ( White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) | item 42 | 1165 | Sqm |
| 44 | 44 | Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.\n(a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) | item 43 | 1165 | Sqm |
| 45 | 45 | Applying one self-priming coat of Unicem \"Shakti\" brand of required shade over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department. | item 44 | 405 | Sqm |
| 46 | 46 | Finishing wall with two coats of waterproofing cement coatings of Unicem \"Shakti\" brand of required shade by thinning 1 part of paint with 1 part of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department. | item 45 | 405 | Sqm |
| 47 | 47 | Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt snd other foreign matter , sand papering and knotting. \n(b). With ready mixed paint , wood primer (white). | item 46 | 74 | Sqm |
| 48 | 48 | Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping.\n(i).Surfaces over 100mm in width or girth.\na). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). | item 47 | 74 | Sqm |
| 49 | 49 | Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper.\na). With ready mixed \"red-lead/ red oxide\" primer. | item 48 | 300 | Sqm |
| 50 | 50 | Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter.\n(i).Surfaces over 100mm in width or girth.\na). General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac). | item 49 | 300 | Sqm |
| 51 | 51 | Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid sepaAPWD Rately).\na)Side hung and Top hung windows and ventilators\n(iv) 5 mm clear glass | item 50 | 15 | Sqm |
| 52 | 52 | Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid sepaAPWD Rately).\na)Side hung and Top hung windows and ventilators(v) 5 mm coloured glass | item 51 | 5 | Sqm |
| 53 | 53 | Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid sepaAPWD Rately).\na)Side hung and Top hung windows and ventilators(ii)5mm Frosted Glass | item 52 | 5 | Sqm |
| 54 | 54 | Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid sepaAPWD Rately).\na)Side hung and Top hung windows and ventilators(ii)5mm Clear Glass | item 53 | 35 | Sqm |
| 55 | 55 | Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels.\n(a)2 Track sliding window\n(ii)5mm frosted glass | item 54 | 100 | Sqm |
| 56 | 56 | Providing, fitting and fixing coloured anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars,joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels.\n(b)3 Track sliding window\n(ii)5mm frosted glass | item 55 | 210 | Sqm |
| 57 | 57 | Providing and fixing anodised aluminium framed double leaf doors of approved brand with styles size 45mm x 48mm x 3.2mm, top rails 50mm x 45mm x 2.5mm, lock rails 48 mm x 45mm x 2.5mm, bottom rails 100mm x 45mm x 2.5mm fitted with tapper clips of size 20mm x15mm x1.2mm complete with automatic floor mounted door closure, butterfly type handles, special cylindrical lock, concealed type aluminium tower bolt,neoprene dryset rubber gusket, door felt gusket, etc.complete as directed by the Department at all levels. \n(iv)6mm coloured glass | item 56 | 35 | Sqm |
| 58 | 58 | Providing, fitting and fixing anodised aluminium framed glazed doors with partition walls partly glass and partly prelaminated board with anodised aluminium frame made of 100mm x 43mm x 2mm sections of approved brand with doors style of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x 43mm x 2mm, fitting with glazing clip, special rubber type gusket complete including hydraulic floor spring pivot aluminium door handle lock angles cleat etc. complete as directed by the department at all levels.\n(ii)6mm clear glass | item 57 | 120 | Sqm |
| 59 | 59 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )\n a) Sliding door bolts\ni) 300mm x 16mm | item 58 | 30 | Sqm |
| 60 | 60 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )\nb) Tower bolts\nii) 250mm x 12mm | item 59 | 450 | Sqm |
| 61 | 61 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )\nc) Door handles\niii) 150mm | item 60 | 225 | Sqm |
| 62 | 62 | Supplying, fitting, fixing anodised aluminium fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.( anodised to bright natural matt & satin finished )\nt) Door stopper with rubber stopper | item 61 | 75 | Sqm |
| 63 | 63 | Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mmx600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm . Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I. system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mmx600mm grid, all complete as per the drawing & directions of engineer-in-charge. \nFinally, if specified, boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid.\n(B) Designer Ceilings of Everest make or equivalent as directed by the departement\n(i) Using 4 mm thick FC Board | item 62 | 250 | Sqm |
| 64 | 64 | Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid sepaAPWD Rately). \n(b) 0.50 mm thick | item 63 | 345 | Sqm |
| 65 | 65 | Providing galvd iron ridging of TATA SHAKTEE / SAIL including supplying and fixing necessary galvd screws/washers etc. complete as directed.\n(b) 0.50 mm thick \n(i) 150 mm lapping | item 64 | 60 | Sqm |
| 66 | 66 | Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floting coat of neat cement finished. | item 65 | 250 | Sqm |
| 67 | 67 | Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.\nii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm. | item 66 | 256 | Sqm |
| 68 | 68 | Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed.\nb) 75mm thick slab | item 67 | 30 | Sqm |
| 69 | 69 | Pre construction anti - termite treatment by applying in the entire levelled area after plinth filling and before laying floor by applying the emulsion @ 5 (five) litres per square meter of the surface to be spread with light rodding so as to ensure proper absorption by the filled up earth (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.\na) with aqueous emulsion having concentration 1:19 with chloropirophose solution (tricel or euivalent) and water, i.e. 1% solution. | item 68 | 250 | Sqm |
| 70 | 70 | Approach Road | Head 2 | ||
| 71 | 71 | Removal of Unserviceable Soil with Disposal upto 1000 metres\n(Removal of unserviceable soil including excavation, loading and\ndisposal upto 1000 metres lead but excluding replacement by\nsuitable soil which shall be paid sepaAPWD Rately as per clause 305.) | item 69 | 70 | Cum |
| 72 | 72 | Construction of Subgrade and Earthen Shoulders (Construction\nof subgrade and earthen shoulders with approved material obtained\nfrom borrow pits with all lifts & leads, transporting to site, spreading,\ngrading to required slope and compacted to meet requirement of\ntable\nfrom Private land | item 70 | 60 | Cum |
| 73 | 73 | Construction of granular sub-base by providing\nclose graded Material, mixing in a mechanical mix plant at OMC,\ncarriage of mixed Material to work site, spreading in uniform layers\nwith motor grader on prepared surface and compacting with\nvibratory power r | item 71 | 30 | Cum |
| 74 | 74 | Water Bound Macadam (Providing, laying, spreading and\ncompacting stone aggregates of specific sizes to water bound\nmacadam specification including spreading in uniform thickness,\nhand packing, rolling with vibratory roller 8-10 tonnes in stages to\nproper grade and camber, applying and brooming requisite type of\nscreening/binding material to fillup the interstices of coarse\naggregate,watering and compacting to the reqd. density ( with an\ninitial lead of 5.0 km. )\nGrading- III | item 72 | 15 | Cum |
| 75 | 75 | Providing and laying interlocking concrete block pavement having thickness 80mm as\nper technical specification clause 1504 | item 73 | 200 | Cum |
| 76 | 76 | Courtyard | Head 3 | ||
| 77 | 77 | Removal of Unserviceable Soil with Disposal upto 1000 metres\n(Removal of unserviceable soil including excavation, loading and\ndisposal upto 1000 metres lead but excluding replacement by\nsuitable soil which shall be paid sepaAPWD Rately as per clause 305.) | item 74 | 70 | Cum |
| 78 | 78 | Construction of Subgrade and Earthen Shoulders (Construction\nof subgrade and earthen shoulders with approved material obtained\nfrom borrow pits with all lifts & leads, transporting to site, spreading,\ngrading to required slope and compacted to meet requirement of\ntable (300-2 ( Including cost of testing of materials at site and\nlaboratory as directed by the deptt.)\n(a) from private land | item 75 | 100 | Cum |
| 79 | 79 | Construction of granular sub-base by providing\nclose graded Material, mixing in a mechanical mix plant at OMC,\ncarriage of mixed Material to work site, spreading in uniform layers\nwith motor grader on prepared surface and compacting with\nvibratory power roller to achieve the desired density,completeas per\ncl. 401( with an initial lead of 5 Km.)( Including cost of testing of\nmaterials at site and laboratory as directed by the deptt.)\nfor grading- II Material | item 76 | 50 | Cum |
| 80 | 80 | Water Bound Macadam (Providing, laying, spreading and\ncompacting stone aggregates of specific sizes to water bound\nmacadam specification including spreading in uniform thickness,\nhand packing, rolling with vibratory roller 8-10 tonnes in stages to\nproper grade and camber, applying and brooming requisite type of\nscreening/binding material to fillup the interstices of coarse\naggregate,watering and compacting to the reqd. density ( with an\ninitial lead of 5.0 km. )\nGrading- III | item 77 | 25 | Cum |
| 81 | 81 | Providing and laying interlocking concrete block pavement having thickness 80mm as\nper technical specification clause 1504 | item 78 | 250 | Cum |
| 82 | 82 | Boundary Wall | Head 4 | ||
| 83 | 83 | Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified.\n(A) Up to a depth of 2.00m below the existing ground level.\n(a) In ordinary soil | item 79 | 325.8 | Cum |
| 84 | 84 | Stone masonary work in retaining wall, wing wall, abutment, foundation, steps, plinth etc. in cement mortar in prop 1:6 with levelling course of 1:6:12 with both faces hammer dressed including bonding, providing face stone, through stone and centering including racking of joints, curing and supplying and all carriage of stone as directed including payment of forest royalty and sales tax and carriage.\n(a) Random Rubble Masonry | item 80 | 282.36 | Cum |
| 85 | 85 | Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.\n(a) With earth or silt or sand obtained by head load with lead upto 90m and lift upto 2m | item 81 | 184.62 | Cum |
| 86 | 86 | Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid sepaAPWD Rately).\n(a) In prop 1cement: 3 sand :6 coarse aggregate by volume | item 82 | 28.236 | Cum |
| 87 | 87 | Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid sepaAPWD Rately)\nUsing Mixer Machine\nIn substructure up to plinth level\nFoundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.\nWithout using admixture, plasticiser\nM15 grade concrete or Prop. 1:2.4 col col. Below tie beam | item 83 | 38.01 | Cum |
| 88 | 88 | In super structure from plinth level up to 1st floor level. \nN) Without using admixture, plasticiser\nM15 grade concrete or Prop. 1:2:4 | item 84 | 21.72 | Cum |
| 89 | 89 | Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in:\nFoundation, footings, bases of columns, pile cap, raft and mass concrete works etc.\nSides of tie beams, grade beams etc. at or below ground level.\nSides of tie beams, grade beams etc. at or below ground level.\nUsing 25mm thick plank | item 85 | 217.2 | Cum |
| 90 | 90 | Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in:\nColumns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face | item 86 | 274.396 | Cum |
| 91 | 91 | Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. | item 87 | 58.463 | Cum |
| 92 | 92 | Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed.\n(I) In Sub-structure upto plinth level including dewatering if necessary\n(b) In proportion 1:4. | item 88 | 47.603 | Cum |
| 93 | 93 | 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid sepaAPWD Rately)\n112mm thick brick wall\n(a) In cement mortar in proportion 1:4. \n(1 cement:4 sand) | item 89 | 323.266 | Cum |
| 94 | 94 | 15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. \nOn rough side\nIn cement mortar 1: | item 90 | 688.705 | Cum |
| 95 | 95 | Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth.\n(a).Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)- 2 coats | item 91 | 688.708 | Cum |
| 96 | 96 | b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials. | item 92 | 688.705 | Cum |
| 97 | 97 | Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.\n(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the APWD Rate) \nb) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX)\n . | item 93 | 51.042 | Cum |
| 98 | 98 | Supplying, fitting and fixing double leaf heavy duty iron gate, frame made from 50mm x 6mm M.S. flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top flat and 20 mm dia M.S. bars at 200mm apart from bottom flat to middle flat including drilling, welding etc. complete. All vertical bars are to be protruded at least 100mm above the middle and top flat is to be flattended and pointed as directed. Necessary locking arrangement on both faces, arrangement for temporary closing the gate and 2 nos.( minium) strong iron hinges of M.S bars and flat of same sizes on each leaf to be embeded in C.C brick pillars as necessary including a red oxide painting to all iron works as directed and specified. (SepaAPWD Rate payment will be made for posts). | item 94 | 4.33 | Cum |
| 99 | 99 | Sanitary and Water Supply | Head 5 | ||
| 100 | 100 | Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid sepaAPWD Rately)\nA) Parryware make \na) White\n(i) Universal Closet S Trap (Cat No.C0271) (Anglo Indian) (inclusive of seat cover) | item 95 | 28 | Each |
| 101 | 101 | Providing fitting and fixing vitreous china flat back type lipped front urinal basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required.\nB) Hindware make\na) White\n(ii)URINAL ALEXA E-Sense (Cat. No.96005) | item 96 | 24 | Each |
| 102 | 102 | Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified. | item 97 | 2 | Each |
| 103 | 103 | Providing fitting and fixing Glass Shelf complete as directed and specified.\nGlass shelf with C.P. guard rail \n(ii) Sona make (Cat. No.TR-0701\n(b) 525mm | item 98 | 33 | Each |
| 104 | 104 | Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified.\n(b) Sona Make\n(i) Soap dish light (Cat.No.TR-0661) | item 99 | 33 | Each |
| 105 | 105 | Providing, fitting and fixing CP towel rail complete as directed and specified.\n(a) Jaquar make\n(iv) Queen's (450mm long) (Cat.No.AQN-7711A) | item 100 | 33 | Each |
| 106 | 106 | Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified.\n(a) Jaquar make \n(i) Continental toilet paper holder (Cat.No. ACN-1151N) | item 101 | 33 | Each |
| 107 | 107 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(i) 160mm dia. | item 102 | 180 | Each |
| 108 | 108 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. (ii) 110mm dia. | item 103 | 110 | Each |
| 109 | 109 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. (iv) 75mm dia. | item 104 | 50 | Each |
| 110 | 110 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 160mm dia. | item 105 | 40 | Each |
| 111 | 111 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(ii) 110mm dia. | item 106 | 130 | Each |
| 112 | 112 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(iv) 75mm dia. | item 107 | 50 | Each |
| 113 | 113 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(i) 160mm | item 108 | 28 | Each |
| 114 | 114 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item 109 | 16 | Each |
| 115 | 115 | Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. \na) In exposed surfaces or in trenches. \n(iv) 75 mm dia. | item 110 | 18 | Each |
| 116 | 116 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damage\n(i) 160mm | item 111 | 20 | Each |
| 117 | 117 | (ii) 110mm dia. | item 112 | 21 | Each |
| 118 | 118 | (iv) 75 mm dia. | item 113 | 19 | Each |
| 119 | 119 | Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.\na) In exposed surfaces or in trenches. \n(i) 160mm dia | item 114 | 28 | Each |
| 120 | 120 | (ii) 110mm dia. | item 115 | 33 | Each |
| 121 | 121 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 160mm dia | item 116 | 10 | Each |
| 122 | 122 | (ii) 110mm dia. | item 117 | 8 | Each |
| 123 | 123 | Supplying fiting and fixing 45degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(i) 160mm dia | item 118 | 14 | Each |
| 124 | 124 | (ii) 110mm dia. | item 119 | 12 | Each |
| 125 | 125 | (iv) 75 mm dia. | item 120 | 8 | Each |
| 126 | 126 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 160mm dia | item 121 | 26 | Each |
| 127 | 127 | (ii) 110mm dia. | item 122 | 28 | Each |
| 128 | 128 | (iv) 75 mm dia. | item 123 | 25 | Each |
| 129 | 129 | Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(i) 160mm dia | item 124 | 12 | Each |
| 130 | 130 | (ii) 110mm dia. | item 125 | 8 | Each |
| 131 | 131 | (iv) 75 mm dia. | item 126 | 8 | Each |
| 132 | 132 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 160mm dia | item 127 | 34 | Each |
| 133 | 133 | (ii) 110mm dia. | item 128 | 33 | Each |
| 134 | 134 | (iv) 75 mm dia. | item 129 | 35 | Each |
| 135 | 135 | Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(ii) 110mm dia. | item 130 | 15 | Each |
| 136 | 136 | (iv) 75 mm dia. | item 131 | 15 | Each |
| 137 | 137 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(ii) 110mm dia. | item 132 | 15 | Each |
| 138 | 138 | (iv) 75 mm dia. | item 133 | 12 | Each |
| 139 | 139 | Supplying fiting and fixing PVC cross ‘T’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(i) 110mm x110mm | item 134 | 8 | Each |
| 140 | 140 | (ii) 75 mm x 75mm | item 135 | 8 | Each |
| 141 | 141 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 110mm x110mm | item 136 | 18 | Each |
| 142 | 142 | (ii) 75 mm x 75mm | item 137 | 18 | Each |
| 143 | 143 | Supplying fiting and fixing PVC coupler of (Supreme / Prince)or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches\n(i) 110 mm dia | item 138 | 12 | Each |
| 144 | 144 | (iii) 75 mm dia | item 139 | 8 | Each |
| 145 | 145 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(i) 110 mm dia | item 140 | 24 | Each |
| 146 | 146 | (iii) 75 mm dia | item 141 | 22 | Each |
| 147 | 147 | Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. \na) In exposed surfaces or in trenches. \n(iv) 110 mm x 75mm | item 142 | 8 | Each |
| 148 | 148 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(iv) 110 mm x 75mm | item 143 | 18 | Each |
| 149 | 149 | Supplying fiting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.\na) In exposed surfaces or in trenches. \n(iii) 110 mm x 75mm | item 144 | 12 | Each |
| 150 | 150 | b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.\n(iii) 110 mm x 75mm | item 145 | 10 | Each |
| 151 | 151 | Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. \n(b) 110 mm | item 146 | 24 | Each |
| 152 | 152 | (c) 75 mm | item 147 | 30 | Each |
| 153 | 153 | Providing fitting fixing CI Grating to the floors complete as directed and specified\n(ii) 110 mm dia PVC Cowel ISI make | item 148 | 28 | Each |
| 154 | 154 | Providing fitting fixing CI Grating to the floors complete as directed and specified\n(ii) 75 mm dia | item 149 | 12 | Each |
| 155 | 155 | Providing fitting and fixing 450mm dia. 90mm thick C.I. Man hole cover and frame of 58 Kg. weight complete as directed and specified. | item 150 | 2 | each |
| 156 | 156 | Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table. | item 151 | 13 | each |
| 157 | 157 | Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed | item 152 | 8 | Each |
| 158 | 158 | Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. \n(A) Exposed or in trenches\nSUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40)\nb) 40 mm dia | item 153 | 200 | RM |
| 159 | 159 | (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure.\nSUPREME/ PRINCE / SFMC / FUSION BAND or other equvalent approved brand (High presure pipe Sch-40)\nc) 32 mm dia | item 154 | 150 | RM |
| 160 | 160 | Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured sepaAPWD Rately)\nJaquare make \n(a)Continental /Clarion\n(i)Standard | item 155 | 60 | Each |
| 161 | 161 | Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid sepaAPWD Rately) \nJaquar\n(a) Continental / Clarion\n(i)15mm dia Male / Female (long thread) | item 156 | 60 | Each |
| 162 | 162 | Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid sepaAPWD Rately) \nEssco brand\na) Sink cock with \"U\" shape swinging casted spout | item 157 | 2 | Each |
| 163 | 163 | Supplying fitting and fixing Chrome Plated (C.P.) shower 15mm dia. Of approved brand as directed and specified. (Pipes will be measured and paid sepaAPWD Rately)\nEssco make\n(h)Round shower with revolving joint 100mm dia | item 158 | 10 | Each |
| 164 | 164 | Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.\nb) 40 mm dia. | item 159 | 5 | Each |
| 165 | 165 | c) 25 mm dia. | item 160 | 6 | Each |
| 166 | 166 | d) 2O mm dia. | item 161 | 6 | Each |
| 167 | 167 | Supplying fitting and fixing gun metal check valve including necessary threads to pipes.\nb) 40 mm dia (Heavy type) | item 162 | 3 | Each |
| 168 | 168 | Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the small tin container (container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost). | item 163 | 150 | RM |
| 169 | 169 | Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department.\nvi) Bore hole of 200mm diameter | item 164 | 150 | RM |
| 170 | 170 | Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department.\nPVC PIPE\n SUPREME /PRINCE / FUSION /SFMC Brand\nvii) 160mm diameter | item 165 | 150 | RM |
| 171 | 171 | Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed.\nA) G.I. pipe\na) TATA / SAIL (Medium)socket should be welded to the pipes.\niv) 50mm diameter | item 166 | 110 | Rm |
| 172 | 172 | Supplying fitting and fixing brass Tez filter 2.00 metre long. | item 167 | 40 | Each |
| 173 | 173 | Supplying fitting and fixing check valve (non return valve) including thread to pipes.\niv) 50mm diameter | item 168 | 4 | Each |
| 174 | 174 | Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained | item 169 | 1 | Job |
| 175 | 175 | Flushing, clearing, washing and watering of the tube well | item 170 | 1 | Job |
| 176 | 176 | Supplying and placing ferrocement water tanks of circular/rectengular shape over stagging with manhole cover with locking and clearing arrangement including providing pads of size as required for inlet and outlet pipes complete as directed.(Stagging should be measured and paid sepaAPWD Rately). \n2000 Lt capacity water tank | item 171 | 4 | Each |
| 177 | 177 | Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration APWD Rate per hour of DOLPHIN make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six monthhs\n(A) With Zoloto fittings \n(II) 2000 liters capacity\n(a) 4 mm thick Vessel | item 172 | 1 | Each |
| 178 | 178 | For Internal electrification | item 173 | 1 | Each |
| 179 | 179 | For external electrification | item 174 | 1 | Each |
| 180 | 180 | Half Statue of Dr. B.R . Ambedkar (L/S) | item 175 | 1 | Each |
| 181 | 181 | Furniture (L/S) | item 176 | 1 | Each |
| 182 | 182 | GST | item 177 | 1 | Each |
| 183 | 183 | Agency Charge (3%) | item 178 | 1 | Each |
AI Tender Summary
Tender Timeline
Feb 08, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 15, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 15, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender