Online Quotation ( E-Quotation ) For The Following Work Are Invited By The Executive Engineer , P . W . Division , Panvel On Behalf Of Government Of Maharashtra By Electronic Tender Management System . From Consultants / Companies / Firms / Contractors / Exp-1 Providing And Fixing Low Height Partitions At Required Location Having Minimum 65Mm Thick Made By Using 50X50mm ( Finished Size ) Centrally Providence Teak Wood ( Cptw ) Section Framing At 600 Mm Center To Center, Covered With 6 Mm Marine Ply Requisite Manufacture Generally Confirming To I.S. 303 / I.S. 710 / -1980 On Both Sides. The Partition Shall Be Finished With Formica Laminate Sheet Finished Lamanation Pattern With Or Without Grooves Externally With Necessary Lipping ( Bourmah Teak Wood ) Moulding Antitermite Treatment To All Plywood And Wood Work Including All Leads And Lifts Etc. Complete As Per Architects Drawing And Instruction Of The Engineer In-Charge. 2 Providing And Fixing Full Height Partitions At Required Location Having Height More Than 1.34M And Minimum 65Mm Thick Made By Using 50X50mm ( Finished Size Centrally Providence Teak Wood ( Cptw ) Section Framing At 600 Mm Center To Center, Covered With 6 Mm Marine Ply Milimeter Thick Requisite Manufacture Generally Confirming To ( I.S. 303 / I.S. 710 / -1980 ) Veneer Pattern With Or Without Grooves Externally With Necessary Lipping ( Bourmah Teak Wood ) Moulding Antitermite Reatement To All Plywood And Wood Work With Ten Years Guarantee Bond With Melamine Polish Etc. Including All Leads And Lifts Etc. Complete As Per Architects Drawing And Instruction Of The Engineer In- Charge. 3 Providing & Fixing Dias Above Advocates Table At Court Hall Of Size 500 X 600 X 450 Mm Height With Following Specification: Table Top :- 25Mm Thick Plain Partical Board Of Exterior Grade ( Confirming To Is-13087 ) With Post Forming Laminate & Balancing Laminate Below With 2.0 Mm Thick Pvc. Edge Band Of Required Size Etc. Complete. Sides, &Bottom :- 25 Mm Thick Both Side Prelamanitedpartical Board Of Exterior Grade ( Confirming To Is- 12823 ( 1990 ) ) With 2Mm Thick Pvc Edge Banding Of Required Size. Etc. Complete. Hardware:- Minifix, Wooden Dowels, Right Angle Connector, M10 Philips Head Screw & Cap ( All Ebco Make ) , Etc. Complete. 4 Providing And Fixing Full Height Door Shutter At Required Location Having Height More Than 1.5M Made By Using Soild Core Commercial Type Flush Doors 35 Mm Thick Of Requisite Manufacture Equivalent With Formica Laminate Sheet Finished Lamination Pattern With Or Without Grooves Externally With Necessary ( Btc ) Moulding, Antitermite Treatment To Plywood And Wood Work Including All Leads And Lifts Complete As Per Architects Drawing And Instruction Of Engineer In-Charge Etc. Complete 5 Providing And Fixing Full Height Door Shutter At Required Location Having Height More Than 1.5M Made By Using Soild Core Commercial Type Flush Doors 35 Mm Thick Of Requisite Manufacture Equivalent With Veneer Pattern With Or Without Grooves Externally With Necessary ( Btc ) Moulding, Antitermite Treatment To Plywood And Wood Work Melamine Polish Including All Leads And Lifts Complete As Per Architects Drawing And Instruction Of Engineer In-Charge Etc. Complete 6 Storage Full Height : Providing And Fixing 53Cm Deep Cupboard Type Storage Unit Made Out Of 19Mm Thick Marine Plywood Of The Requisite Manufacture Generally Confirming To I.S. 710-1980 For Frames, Internal Verticals Horizontal Divisions, Shutters And 6Mm & 12Mm Thick Marine Plywood For Drawers With Locks, Handles, Hardware, Lipping & Beading Patti ( Btc ) Etc. The Shall Be Finished With Veneer In Approved Pattern With Grooves Etc. And Two Coats Of French Polish And Melamine Polish For All Btc Moulding & Lipping Patties With Antitermite Treatment To Plywood & Wood Work With Ten Years Guarantee On Requisite Stamp Paper Including All Leads & Lifts Etc. Complete As Per Drawing And Instruction Of Engineer- In-Charge Etc. Complete. 7 Low Height Storage - Providing & Fixing On Site 40 Cm Deep Low Height Storage Unit At Require Location Less Than 1.35 Meter Height By Using 19Mm Marine Ply Of Requisite Manufacture Generally Confirming To I.S. 303 / Is. 710-1980 For Frame, Internal Verticals, Horizontal Divisions, Openable Shutters, 6Mm Thick Marine Ply Back, With Necessary Locks, Handles, Hardware, Lipping ( Btc ) , Moulding Etc. The Total Shall Be Finished With Formica Laminate Sheet Finished Lamination Pattern With Grooves Externally And Two Coats Of French Polish With Anti-Termite Treatemtn To Plywood & Wood Work Including All Leads & Lifts Etc. Complete, As Per Architects Drawing And Instruction Of Engineer In Charge. 8 Judge Tables ( 2.13X0.91 ) : Providing & Supplying Table For The Executive Officer Having Made Out Of 19Mm Thick Marine Ply Of The Requisite Manufacture Generally Confirming To I.S.303 / I.S.710-1980 Top Side & Apron, Having 38X54x75 Cm. Storage Boxes On Both Side Made Up Of 19Mm Marine Ply For Sides, Shutters, Horizontal And Vertical Divisions 12Mm ( 6Mmx2 ) Thick. Marine Ply Of Requisite Manufacture Generally Confirming To I.S.303 / I.S701-1980 Back And Three Drawers On One Side Made By Using 19Mm Marine Ply Front And Ply Sides, 6Mm Marine Ply Bottom With Necessary Lipping ( Btc ) S, Mouldings Etc. And C.P.T.W. Footrest Out Of 75 X 40Mm ( Finished Size ) Section, The Table Shall Be Externally Finished With 4Mm Thick Group Match Veneer Of Opproved Make & Pattern With Grooves Including Necessary Lipping ( Btc ) , Moulding, French Polish With Antitermite Treatment, Melamine Polish For Venner And Exposed Lipping ( Btc ) Moulding Antitermite To Plywood And Wood Work With Ten Years Guarantee Bond Etc Complete. 9 Tables ( 1.20X0.60 ) : Providing & Fixing In Position Table For The Clerical Staff Having Overall Size Of 120X60x76 Cm Height Made Out Of 19Mm Thick Marine Ply Of The Requisite Manufacture Generally Confirming To I.S.303 / I.S.710-1980 Top, Vertical Side & 6Mm Marine Plywood Of Requisite Manufacture Generally Confirming To Sides And 6Mm Marine Ply Bottom With Necessary Sliders One Open Shelf Of 19Mm Thick Marine Ply With Necessary Lipping On External Sides And Foot Rest Out Of 40X75 Mm ( Finished Dimension ) Cptw Etc. As Per Drawing And Instructions. The External Side And Top Shall Be Finished With 1Mm Thick Laminate Matt / Suede / Fine Line Finished Lamination Pattern With Grooves All Internal Surfaces On Table And Drawer Shall Be Internally Finished With Two Coats Of French Polish With Antitermite Treatment. 10 Judge Chair : Providing And Fixing An Executive Chair Made In Well Seasoned Old Burma Teak With Carved Details. The Chair Shall Be Constructed In Old Burma Teak Wood As Per The Image In The Drg. The Seat Shall Be Covered With Composite Leather ( Instead Of Cane ) And The Back Shall Be Netted In Cane As Shown. All Wooden Surfaces Shall Be Finished With Approved French Polish. Basic Rate Of Leater Rate: 300 / M Item To Include Spray Coating All The Surfaces With Approved Anti Termite Solution Including Providing 10 Year Guarantee For The Same As Direxted By The Architect Or Engineer In Charge 11 Court Chair : Providing Single Circular Chair Which Shall Be Constructed In Well Seasoned Old Burma Teak Wood As Per The Original Design At High Court Building And As Per Image In The Drg. The Seat Shall Be Netted In Cane As Shown. All Wooden Surfaces Shall Be Finised With Approved French Polish. Item To Include Spray Coating All The Surfaces With Approved Anti Termite Solution Including Providing 10 Year Guarantee For The Same As Directed By The Architect Or Engineer In Charge. 12 Judge Chair Anti Chamber : Providing Executive Chairs For Judges Having A High Back With An Adjustable Head Rest With A Synchorized Tilting Meachnism With Multiple Locking Systems, Abs For Seat, Cushioned Back With Extra Lumber Support With Fine Tuning For Depth Adjustment, With Swivel & Depth. The Chair Shall Have Adjustable Arm Pad & Option Of Pvc Padding. The Seat Shall Have A Gas Lift For Height Adjustment And The Chair Shall Have A Nylon Base With Castors. 13 Staff Revolving Chair : Providing Visitor Chairs Having A Medium Back With Head Rest, With A Synchronized Tilting Mechanism With Multiple Locking Systems, Abs For Seat, With Swivel & Depth. The Chair Shall Have Adjustable Arm Pad & Option Of Pvc Padding. The Seat Shall Have A Gas Lift For Height Adjustment And The Chair Shall Have A Nylon Base With Castors. 14 Visitors Chairs / Fix Chair : The Seat And Back Are Made Up Of 1.2 Cm. Thick Hot-Pressed Plywood, Upholstered With Fabric Upholstery Covers And Moulded Polyurethane Foam. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. The Seat Has Extra Thick Foam On Front Edge To Give Comfort To Popliteal Area. Back Size:47.5 Cm. ( W ) X 58.0Cm. ( H ) Seat Size: 47.0 Cm. ( W ) X 48.0 Cm. ( D ) Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 + / -2 Kg / M3 And Hardness = 20 + / - 2 On Hampden Machine At 25% Compression.3 ) Armrests: The One-Piece Armrests Are Injection Moulded From Black Copolymer Polypropylene As Per Order. ( Material Supplied Should Be Standard Company ) 15 2 Seater Sofa : Providing & Supplying Two Seater Sofa Of Overall Size 1350X760x825 Mm Ht. Made Out Of 75X38mm ( Finished Size ) With Cctw Section Frame 6Mm Commercial Plywood Generally Confirming To I.S.303 / I.S. 710-1980 For Necessary Covering From Back &Arm Rests. The Seat Shall Be 100Mm Thick Dunlop Or Mm Or Equivalent Brand Quality Foam Covered 1 Soft Foam And Arms Having Cctw 50Mm Thick 50 Density Branded Foam Covered 1 Plain Soft Foam. All Work Covered With Tapestry Fabric Upto Rs.400 / - Per Smt.Including Necessary Hardware, Naver, Jute Cloth.Casement, Springs Or Belted Absorber Etc. Complete. All Exposed Wooden Surface Shall Be Melamine Polished And Antitermite Treatment To Plywood And Wood Work With Five Years Guarantee Bond Etc. Including All Leads & Lifts Etc. Complete As Per Architects Drawing & Instruction Of Engineer-In-Charge. 16 Providing And Supplying Cctw Stool Of Size 0.45X0.45 Mtr. Of Height 0.75 With Using Cctw Frame Work And Top Of 25 Mm Thick, As Per Approved Typical Drawing With French Polishing And Finishing Etc Complete 17 Supplying Glass Table Top 8 Mm Thick In Required Size And Shape Including Finishing The All Side Edges Machnically Smoothly Etc. Complete. 18 Making And Providing By Fixing Roller Blinds Fabricks Curtains For Window In Approved Sample By Using Powder Coated Rod And Machinical System With Chain For Opening / Closing Moments Of The Blinds And Fixing Properly At Sites And At Director Engineer In Charge. 19 Supplying Table Cloth ( Sarj ) ( Material Supplied Should Be Standard Company ) 20 Providing And Supplying Foot Rest Below Table As Per Approved Typical Drawing Size And Height Using Commercial Plywood 18 Mm Thick With French Polishing And Finishing Etc Complete 21 Single Static Drive Type Body 2 Bay Of Compactors Of Size 1790 Mm X 445 Mm X 2375 Mm Made Out Of 0.8 Mm Thick Cold Rolled Cold Annealed Steel Conforming To Is:513 Grade, Having 5 Loading Levels ( Load Bearing Capacity - 80 Kgs Uniformly Distributed Load ) Formed By 4 No?S Adjustable Shelves, Finished With Fire Retardant Epoxy Polyester Powder Coating Of Approved Color & Shade With A Dry Film Thickness Of Minimum 40 Microns, Oven Baked With A Controlled Temperature Of 180 Deg.C To 200 Deg.C, The Undercarriage Made Up Of Welded Frame Of Hr Sheet 3.15Mm Thk Conforming To Is:10748 Suitably Fabricated To Take The Load Based On Configuration Having Fasteners, Label Holders, Mounted On Guide Channels As Per Attached Detailed Specifications And Design Etc. Complete.Vertical Structure To Be J Profile. Two Such J Profiles To Be Joined Together With Full Steel Sheet And Welded For Additional Strength. Shelf To Have Mimimum 30 Mm Bend. Each Shelf To Have Minimum 10 Bends. ( Single Static Drive Type Body 2 Bay Of Compactors ) ( Sketch Attached Seprately ) 22 Abc 6 Kg New Fire Extinguisher, Valve Pressure Gauge, Pvc Hose Pipe, Safety Pin, Isi No 15683, Wall Bracket With Complete Fire Extinguisher
