| 1 | 1 | Clearing grass and removal of rubbish on both side of the road to facilitate widening of berms ,disposal of the stuff including all labour, T&P articles required for the work etc. complete as per cluse 201 of MORD by manual means etc. complete as per direction of the Engineer-in-charge | | 25870 | Sqm |
|---|
| 2 | 2 | Construction of embankment with approved material obtained from borrow pits transporting to site by manual means with initial leads & lifts, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 as per Technical Specification | | 9771.56 | Cum |
|---|
| 3 | 3 | Excavation for roadway in hard rock (blasting prohibited) with rock breakers including breaking rock, loading in tippers and disposal with a lift upto 1.5 m and lead upto 1000 metres, trimming bottom and side slopes in accordance with requirements of lines, grades and cross- sections as per Technical Specification Clause 302.3.5 and as per the direction of the Engineer-in-charge | | 542.365 | Cum |
|---|
| 4 | 4 | Excavation in Hilly Area in Ordinary Rock not requiring Blastig by Mechanical Means including Cutting and Trimming of side slopes and disposing of excavated Earth with a lift upto 1.5m and a lead upto 20m as per Techical Specification Clause 1603.2. | | 1084.73 | Cum |
|---|
| 5 | 5 | Excavation in Soil in Hilly Area by Mechanical Means including Cutting and Trimming of side slopes and disposing of excavated Earth with a lift upto 1.5m and a lead upto 20m as per Techical Specification Clause 1603.1. | | 3796.55 | Cum |
|---|
| 6 | 6 | Construction of embankment with approved materials deposited at site from road way cutting and excavation from drain & foundation of other strutures graded & compacted to meet the requirement of Tables 300.1 & 300.2 as per clause no.301of MORD specification for Rural roads and as per direction of Engineer-In-Charge. | | 5414.93 | Cum |
|---|
| 7 | 7 | Loosening, Levelling and compacting original ground supporting embankment to facilitate placement of first layer of embankment ,scarified to a depth of 150mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in tables 300.1 and 300.2 for embanckment counstruction as per technical Specification Clause 301.4.1 | | 3880.5 | cum |
|---|
| 8 | 8 | Construction of granular sub-baseIV by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. | | 1233.11 | Cum |
|---|
| 9 | 9 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. | | 761.18 | Cum |
|---|
| 10 | 10 | Providing and applying primer coat with bitumen Emulsion [SS-1] on prepared surface of Granular base including cleaning of road surface & spraying primer @ 0.70kg/ 1.0 kg/sqm using mechanical means as per clause 502 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per direction of Engineer-in charge. | | 7611.75 | Sqm |
|---|
| 11 | 11 | Providing and applying tack coat with bitumen Emulsion [RS-1] using emulsion distributor @ 0.25 to 0.30 kg /sqm on the prepared granular surface treated with primer & cleaned with hydraulic broom as per clause 503 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per direction of Engineer-in charge. | | 7611.75 | Sqm |
|---|
| 12 | 12 | Providing and laying bituminous macadam with 60-90 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction | | 380.59 | Cum |
|---|
| 13 | 13 | Providing and laying semi dense bituminous concrete with 60-90 TPH HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects | | 190.29 | Cum |
|---|
| 14 | 14 | Earthwork in excavation for foundation of structures in all types of soil as per drawing and technical specification Clause 305 and 1104 of MoRD includding setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead & lift, dressing of sides and bottom and back filling with excavated suitable material upto 3mt. as per direction of Engineer-in-Charge. | | 276.91 | Cum |
|---|
| 15 | 15 | Providing CC 1:3:6 for plain/reinforced concrete in open foundations complete as per drawings and technical specification clause 802,803,1202,1203 | | 61.76 | Cum |
|---|
| 16 | 16 | Plain cement concrete 1:2:4 nominal mix in foundation with crushed stone aggregates to 40mm nominal size mechanically mixed placed in foundation and compacted by vibration including curing for 14 daysas per specifcation and direction of the Engineer-in-charge | | 170.52 | Cum |
|---|
| 17 | 17 | Plain cement concrete in sub structure, Nominal mix (1:2:4) complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 and 1204 | | 69.03 | Cum |
|---|
| 18 | 18 | Providing and laying reinforced cement concrete pipe (NP3) for culverts including fixing collar with cement mortar 1:2 but excluding excavation,protection works,backfilling, concrete and masonry work in head wall and parapets as per Clause 1106 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the worketc complete and as per direction of Engineer-in-Charge\n1000 mm dia S/R HPC | | 22.5 | RMT |
|---|
| 19 | 19 | Providing concrete M-25 for plain/reinforced concrete in open foundation/Sub structure/ superstructure complete as per drawings and technical specification clause 800,1205.4,1205.5 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per the direction of the Engineer-in-Charge. | | 8.41 | Cum |
|---|
| 20 | 20 | Supplying, fitting and placing HYSD bar for Sub structure reinforcement complete as per drawings and technical specifications Clause 100 and 1202 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per the direction of the Engineer-in-Charge.. | | 27.69 | Qntl. |
|---|
| 21 | 21 | Providing Weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall etc.all complete as per Clauses 614, 709, 1204.3.7 of MORD specification for Rural roads and as per direction of Engineer-in- charge. | | 69 | No |
|---|
| 22 | 22 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification as per Clause 1200,1204.3.8 of MoRD and as per direction of the Engineer-in-Charge. | | 35.59 | Cum |
|---|
| 23 | 23 | Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and MORD specification Clause 300,800 & 1700 and Annexure 1700.1 of MORD and as per direction of the Engineer-in-charge. | | 2 | no |
|---|
| 24 | 24 | Reinforced cement concrete M15 grade Kilometre stone / local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 of MORD as per direction of Engineer-in-charge. | | | |
|---|
| 25 | 24.01 | 1 km stone | | 1 | no |
|---|
| 26 | 24.02 | 200 mtr stone | | 9 | no |
|---|
| 27 | 24.03 | 5th stone | | 8 | no |
|---|
| 28 | 25 | Providing and fixing of typical PMGSY logo asper mord specification and drawing . Three Ms plateof 1.6 mm thick top and middle plate duty welded with ms angle iron frame of the lawer most plate duly welded to 2 nos . 75 mm x75mm of 12 SWGtubes posts duly embedded in cement concrete m-15 grade blocks of 450mmx450mm x600mm ,600mm beloe ground level. the topmost diamond plate wiil be welded the middle plate by enameled on both sides Lettering and printing arrows, boarder etc | | 1 | no |
|---|
| 29 | 26 | Reinforced cement concrete M15 grade Guard stone/local stone of standard design as per IRC:25 fixed position including finishing and lettering but excluding painting as per drawing and Technical specification Clause 1704 of MORD. | | 325 | no |
|---|
| 30 | 27 | Providing and fixing of typical PMGSY Maintenance information board as per MORD specifications and drawing. Three MS Plates of 50x5mm mm thick, back plate duly welded with 75mm dia steel tubes back on edges as per drawings. The upper & lower plate will be welded with MS flat iron frame of 50mmx5mm. The steel tubes duly embedded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm below ground level.All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexture 1700.1. | | 1 | no |
|---|
| 31 | 28 | Providing and fixing of typical PMGSY Citizen Information board as per MORD specification and drawing. Three MS plates of 50 x 5 mm. thick, back plate duty welded with 75 mm dia steel tubes back on edges as per drawings. The upper and lowe plate will be welded with MS flat iron frame of 50mm x 5 mm. The steel tubes dully embeded in cement concrete M-15 grade blocksw of 600mm x 600 mm x 750 mm below ground level. All MS will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with redimixed synthetic enamel paint of superor quality in required shade and colour. All selection of framed posts and steel tubes will be painted with primer and two coats of epoxupaint as per drawing Clause 1701 and Annexure - 1700.1. and as per the direction of the Engineer-in-charge | | 2 | nos |
|---|
| 32 | 29 | Providing and fixing of RCPLWE informatory sign board of size 5mx2m with retro reflective letters as per MORD specifications and drawing. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and as per direction of Engineer-in charge | | 2 | nos |
|---|
| 33 | 30 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1700 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1700,300 & 800 of MORD etc. complete as per direction of the Engineer-in-Charge | | | |
|---|
| 34 | 30.01 | i) 900mm equilateral triangle ( turn & reduced carriage way ) | | 9 | nos |
|---|
| 35 | 30.02 | ii) 600mm equilateral triangle ( turn & reduced carriage way ) | | 5 | nos |
|---|
| 36 | 30.03 | 600 mm x 450 mm rectangular | | 13 | nos |
|---|
| 37 | 30.04 | MAINTENANCE | | | |
|---|
| 38 | 31 | Routine Maintenance after completion of construction works for 1 st year | | 1.99 | km |
|---|
| 39 | 32 | Routine Maintenance after completion of construction works for 2 nd year | | 1.99 | km |
|---|
| 40 | 33 | Routine Maintenance after completion of construction works for 3 rd year | | 1.99 | km |
|---|
| 41 | 34 | Routine Maintenance after completion of construction works for 4 th year | | 1.99 | km |
|---|
| 42 | 35 | Routine Maintenance after completion of construction works for 5 th year | | 1.99 | km |
|---|
