Name of Work: CRS Project for Electronics and Communication Engineering
Sl.No.
Item Description
Item Code / Make
Quantity
Units
1
1
White Light Source:-\nSpecification- \nNominal Bulb Power ~20 W (tungsten halogen)\nSource High-powered Tungsten Halogen\nTypical Output Power ~8.4 mW\nWavelength Range ~360nm - 2.4µm\nColor Temperature ~3,000 K\nDrift of Optical Output <0.3% per hour\nSource Lifetime ~1,000 hours (typical)\nStability of Light Source Output ~0.25% peak-to-peak\nWarm-up Time <10 minutes\nSafety & Regulatory CE, ROHS, WEEE\nOperating Humidity Specification 5-95% without condensation at 40 °C\nOperating Temperature 5 °C – 35 °C\nFiber Connector SMA 905\nDimensions ~(6.2 x 6 x 15 cm)\nIntegrated Cuvette Holder Yes/No\nIntegrated Filter Holder Yes/No\nPower Consumption up to 30 W\nPower Requirements ~24 VDC\nTrigger/Shutter Input Connection SUB-D-15 pin\nTrigger/Shutter Input Signal TTL; Up to 2.5 Hz maximum\nWeight ~0.5 kg\n
item1
1
N0.
2
2
Spectrometer :-\nSpecification-\nDetector Toshiba TCD1304AP, 190 nm – 1100 nm\nWavelength range 200 – 1100 nm\nIntegration time 4 milliseconds to 20 seconds (continuous); 10 microseconds to 4 milliseconds (shutter)\nDynamic range 2 X 109 (system); 2000:1 for a single acquisition\nSignal-to-noise ratio 300:1 (at full signal)\nGrating HC-1, 300 lines per nm grating\nSlit ~5 µm wide\nOptical resolution <1.0 nm FWHM (note: resolution varies at either end of the spectral range)\nStray light <0.05% at 600 nm; <0.10% at 435 nm\nFiber optic connector SMA 905 to single-strand optical fiber (0.22 NA)\nPower consumption 450 mA @ 5 VDC\nStrobe functions 2 programmable strobe signals (single/continuous)\nInterfaces USB 2.0, 480 Mbps; 2-wire RS-232; I2C 2-wire serial bus\nTemperature -30 °C to +70 °C Storage & -10 °C to +50 °C Operation\nHumidity 0%–90% non-condensing\nSoftware Compatible software\n
item2
1
N0.
3
3
Chemical Vapour Deposition Unit :-\nSpecification-\nReactor:- Imported Quartz Glass Tubular Reactor 40 mm ID x 1200 mm Length with Adaptors ate Inlet & Outlet for Multiple Gas Flow\nControl :-High Temperature Digitally Controlled Electrically Heated Furnace for Temperatures up to 1200 Deg C with Precise PID Control .\nTypical Furnace is designed to split in Three Equal Heating Zones\nPanel indicators:- Powder Coated Panel with Digital Temperature Indicators\nValves:- SS Manifold with Needle valves and Non Return Valves at Inlet of Quartz Tube for Multiple Gases\nStand:- Complete System Mounted on Powder Coated Stand\nFlow controller:- Brooks / Aalborg Make Mass Flow Controller for H2/ N2 or O2 Gases with Calibration Certificate\nData recording:- Data Recording with Software for Flow, Temperatures, And Pressure Recording ( PC by Client )\n
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
