Venkidag Cvcs Ltd No . 337 Maintenance Of Wporshed Maintenance Of Wporshed , Electrification , Water Supply , Toilet Etc .
Tender Value
34.80 Lakhs
Estimated cost
Bid Submission
13 Jan 2020
0 days left
EMD
50000
Bank guarantee accepted
Document Fee
2950
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Enamakkal PO, Thrissur → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Venkidag Cvcs Ltd No . 337 Maintenance Of Wporshed Maintenance Of Wporshed , Electrification , Water Supply , Toilet Etc .
BOQ
| Name of Work: VENKIDANG CVCS LTD NO.R 337 MAINTANANCE OF WORKSHED, ELECTRIFICATION, WATER SUPPLY AND TOILET etc. | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | RAMP | |||
| 2 | 1.01 | 2.8.1\nEarth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation\ntrenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and\nramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus\nexcavated soil as directed, within a lead of 50 m.All kinds of soil | 4.389 | cum | |
| 3 | 1.02 | 4.1.8\nProviding and laying in position cement concrete of specified grade excluding the cost of centering and\nshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40\nnominal size) | 2.671 | cum | |
| 4 | 1.03 | 7.1.1\nRandom rubble masonry with hard stone in foundation and plinth including levelling up with cement\nconcrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth\nlevel with:Cement mortar 1:6 (1 cement : 6 coarse sand) | 4.14 | cum | |
| 5 | 1.04 | 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not\nexceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m\nand lift up to 1.5 m. | 4.389 | cum | |
| 6 | 1.05 | 4.1.10\nProviding and laying in position cement concrete of specified grade excluding the cost of centering and\nshuttering - All work up to plinth level:1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40\nmm nominal size) | 0.732 | cum | |
| 7 | 1.06 | 13.1.2\n12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand). | 7.315 | m2 | |
| 8 | 2 | WORKSHED NO 1 | |||
| 9 | 2.01 | 15.28.2\nDismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50\nmetres lead of :Asbestos Sheet | 138.213 | m2 | |
| 10 | 2.02 | 15.14.1\nDismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above | 0.383 | cum | |
| 11 | 2.03 | 10.16.2\nSteel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including\ncutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding\nand bolted with special shaped washers etc. complete.Hot finished seamless type tubes | 1607.04 | kg | |
| 12 | 2.04 | 12.50\nProviding and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as\napproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams\nper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and\npolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to\navoid scratches during transportation and should be supplied in single length upto 12 metre or as desired\nby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)\nwith EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of\npurlins, rafters and trusses and including cutting to size and shape wherever required | 133.921 | m2 | |
| 13 | 2.05 | 12.51.1\nProviding and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total\ncoated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc\ncoating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both\nside of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws\ncomplete:Ridges plain (500-600 mm) | 34.8 | m | |
| 14 | 2.06 | 13.52.1\nFinishing with Epoxy paint (two or more coats) at all locations prepared and applied as per\nmanufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On\nsteel work | 66.961 | m2 | |
| 15 | 2.07 | od105863/2018_2019\nSupplying and fixing 200mm dia pvc half cut section with brackets at end of sheets or tiled roof rain water\ncollection including all cost of materials,conveyance and labour charges etc,complete | 27.2 | m | |
| 16 | 2.08 | 12.7.2\nProviding and fixing 15cm wide, 45 cm overall semi circular plain G.S. sheet gutter with iron brackets\n40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water\npipes complete.0.63 mm thick with zinc coating not less than 275 gm/ m2 | 10.6 | m | |
| 17 | 2.09 | 50.6.2.2\nSolid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size\nconfirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM\n1:6 ( 1 cement : 6 coarse sand) etc complete | 6.286 | cum | |
| 18 | 2.1 | 9.48.2\nProviding and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or\nround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden\nframes with rawl plugs screws etc | 485.401 | kg | |
| 19 | 2.11 | 5.47.1\nProviding and fixing in position factory made precast RCC M-40 doors and win frames having excellent\nsmooth finish as per IS:6523 with reinforcement of 3 Nos, 6 mm dia main bars tied with 3 mm M.S\nstirrups placed @ 200 mm CC nad 6 numbers high strength polymer blocks of required size for fixing\nhinges including providing 6 no specially designed M.S galvanised sleeves for accomodating 6 mm dia\nfully threaded bolts for fixing hold fast on vertical members, providing suitable arrangement for receiving\nsliding door bolts and tower bolt etc all complete, as per the direction of Engineer in charge. (The cost of\nhold fast and cc block of 1:3:6 mix is also included in the item.) The frame shall be measured in running\nmeter correct to two places of decimal.Door frame 125 mm x 60 mm. | 6.2 | m | |
| 20 | 2.12 | 9.20.1\nProviding and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core\nof block board construction with frame of I st class hard wood and well matched teak 3 ply veneering with\nvertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI\nmarked Stainless Steel butt hinges with necessary screws | 2.1 | m2 | |
| 21 | 2.13 | 15.7.4\nDemolishing brick work manually / by mechanical means including stacking of serviceable material and\ndisposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In\ncement mortar | 0.661 | cum | |
| 22 | 2.14 | od106796/2018_2019\nEngaging labour for dismantling existing sanitary fittings etc. complete. | 5 | each | |
| 23 | 2.15 | 13.1.1\n12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 134.106 | m2 | |
| 24 | 2.16 | 14.1.2\nRepairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including\ncutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls\ncomplete, including disposal of rubbish to the dumping ground within 50 meters lead:Cement mortar 1:4 (\n1 cement: 4 coarse sand) | 43.765 | m2 | |
| 25 | 2.17 | 15.12.1\nDismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats,\narchitrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below | 15 | each | |
| 26 | 2.18 | 21.1.1.2\nProviding and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up\nstandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :\n733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the\ngaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.\nAluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever\nrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel\nscrews, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing,\npaneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium\n(minimum thickness of powder coating 50 micron) | 5.76 | kg | |
| 27 | 2.19 | 21.14\nProviding and fixing anodised aluminium ( anodised transparent or dyed to required shade according to\nIS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with\nextruded built up standard tubular section of approved make conforming to IS: 733 and IS: 1285, fixed\nwith dash fastener of required dia and size (Dash fastener to be paid for separately) | 5.76 | kg | |
| 28 | 2.2 | 21.3.1\nProviding and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM\nrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -\nin -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0\nmm thickness | 1.44 | m2 | |
| 29 | 2.21 | 13.43.1\nApplying one coat of water thinnable cement primer of approved brand and manufacture on wall\nsurface:Water thinnable cement primer | 410.11 | m2 | |
| 30 | 2.22 | 13.60.1\nWall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two\nor more coats on new work | 410.11 | m2 | |
| 31 | 2.23 | 13.62.1\nPainting with synthetic enamel paint of approved brand and manufacture of required colour to give an\neven shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of\napproved brand and manufacture . | 15.302 | m2 | |
| 32 | 2.24 | 13.50.3\nApplying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and\nmanufacture on steel galvanised iron /steel works | 12.58 | m2 | |
| 33 | 2.25 | 13.61.1\nPainting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or\nmore coats on new work | 12.58 | m2 | |
| 34 | 2.26 | 11.36\nProviding and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be\nspecified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green,\nblack of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm\nthick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg\nper sqm, including pointing in white cement mixed with pigment of matching shade complete. | 15 | m2 | |
| 35 | 2.27 | 11.37\nProviding and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the\nmanufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory,\nGrey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including\npointing the joints with white cement and matching pigment etc., complete. | 3.851 | m2 | |
| 36 | 2.28 | 17.2.1\nProviding and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat\nand lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled\ndevice (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and\nmaking good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat\nand lid | 2 | each | |
| 37 | 2.29 | 50.17.1.4\nSupplying and fixing CP Health faucet good quality including cost of materials and labour charges etc.\ncomplete as per the direction of site engineer-in-charge. | 2 | no | |
| 38 | 2.3 | 17.7.2\nProviding and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste\nof standard pattern, including painting of fittings and brackets, cutting and making good the walls\nwherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass\npillar tap | 2 | each | |
| 39 | 2.31 | 18.56.2\nProviding and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 125 mm long\nfoam flow, weighing not less than 120 gms | 4 | each | |
| 40 | 2.32 | 50.18.7.3.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall | 6 | mtr | |
| 41 | 2.33 | 50.18.9.14.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall | 6 | mtr | |
| 42 | 2.34 | 50.18.9.17.1\nProviding and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This\nincludes jointing of pipes with one step PVC solvent cement and testing of joints complete as per\ndirection of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall | 6 | mtr | |
| 43 | 2.35 | 50.18.9.19.1\nProviding and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This\nincludes jointing of pipes with one step PVC solvent cement and testing of joints complete as per\ndirection of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall | 6 | mtr | |
| 44 | 2.36 | 50.18.9.20.7\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 63 mm dia vent cowl | 2 | no | |
| 45 | 2.37 | 50.18.9.20.1\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 63 mm dia Elbow | 3 | no | |
| 46 | 2.38 | 50.18.9.20.2\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement -63 dia 45 degree Elbow | 3 | no | |
| 47 | 2.39 | 50.18.9.20.3\nProviding and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 63 mm dia Door Elbow | 3 | no | |
| 48 | 2.4 | 50.18.9.20.4\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 63 mm dia Bend | 3 | no | |
| 49 | 2.41 | 50.18.9.20.5\nProviding and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC\nsolvent cement - 63x63x63 mm dia Tee | 3 | no | |
| 50 | 2.42 | 50.18.9.20.8\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 63 mm dia End cap | 1 | no | |
| 51 | 2.43 | 50.18.9.20.9\nProviding and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement-63 mm dia Socket /coupling | 1 | no | |
| 52 | 2.44 | 50.18.9.22.1\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110 mm dia Elbow | 4 | no | |
| 53 | 2.45 | 50.18.9.22.2\nProviding and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110 mm dia 45 degree Elbow | 2 | no | |
| 54 | 2.46 | 50.18.9.22.3\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement-110 mm dia Door Elbow | 2 | no | |
| 55 | 2.47 | 50.18.9.22.4\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement- 110 mm dia Bend | 2 | no | |
| 56 | 2.48 | 50.18.9.22.5\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC\nsolvent cement 110x110x110 mm dia Tee | 2 | no | |
| 57 | 2.49 | 50.18.9.22.6\nProviding and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110x110x110 mm dia Door tee | 4 | no | |
| 58 | 2.5 | 50.18.9.22.12\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110x75 mm dia Reducer | 2 | no | |
| 59 | 2.51 | od107089/2018_2019\nSupplying and fixing ready made RCC Septic tank of size 200cm x 60 cm and soak pit , including all cost of materials,labour and onveyance charges etc.complete | 1 | each | |
| 60 | 3 | WORKSHED NO 2 | |||
| 61 | 3.01 | 15.28.2\nDismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50\nmetres lead of :Asbestos Sheet | 123.869 | m2 | |
| 62 | 3.02 | 15.14.1\nDismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height\nincluding stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above | 1.047 | cum | |
| 63 | 3.03 | 10.16.2\nSteel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including\ncutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding\nand bolted with special shaped washers etc. complete.Hot finished seamless type tubes | 1486.42 | kg | |
| 64 | 3.04 | 12.50\nProviding and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as\napproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams\nper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and\npolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to\navoid scratches during transportation and should be supplied in single length upto 12 metre or as desired\nby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)\nwith EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of\npurlins, rafters and trusses and including cutting to size and shape wherever required. | 123.869 | m2 | |
| 65 | 3.05 | 12.51.1\nProviding and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total\ncoated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc\ncoating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both\nside of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws\ncomplete:Ridges plain (500-600 mm) | 17.3 | mtr | |
| 66 | 3.06 | od105863/2018_2019\nSupplying and fixing 200mm dia pvc half cut section with brackets at end of sheets or tiled roof rain water\ncollection including all cost of materials,conveyance and labour charges etc,complete, | 34.6 | mtr | |
| 67 | 3.07 | 13.52.1\nFinishing with Epoxy paint (two or more coats) at all locations prepared and applied as per\nmanufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On\nsteel work | 61.935 | m2 | |
| 68 | 3.08 | 14.1.2\nRepairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including\ncutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls\ncomplete, including disposal of rubbish to the dumping ground within 50 meters lead:Cement mortar 1:4 (\n1 cement: 4 coarse sand) | 16 | m2 | |
| 69 | 3.09 | 15.12.1\nDismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats,\narchitrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below | 1 | each | |
| 70 | 3.1 | 21.1.1.2\nProviding and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up\nstandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :\n733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the\ngaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.\nAluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever\nrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel\nscrews, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing,\npaneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium\n(minimum thickness of powder coating 50 micron) | 18.225 | m2 | |
| 71 | 3.11 | 21.3.1\nProviding and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM\nrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -\nin -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0\nmm thickness | 4.051 | m2 | |
| 72 | 3.12 | 21.14\nProviding and fixing anodised aluminium ( anodised transparent or dyed to required shade according to\nIS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with\nextruded built up standard tubular section of approved make conforming to IS: 733 and IS: 1285, fixed\nwith dash fastener of required dia and size (Dash fastener to be paid for separately) | 18.225 | kg | |
| 73 | 3.13 | 11.3.1\nCement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a\nfloating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.\ncomplete.40 mm thick with 20 mm nominal size stone aggregate | 73.35 | m2 | |
| 74 | 3.14 | 2.8.1\nEarth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation\ntrenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and\nramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus\nexcavated soil as directed, within a lead of 50 m.All kinds of soil | 5.145 | cum | |
| 75 | 3.15 | 50.6.2.1\nSolid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available\nsize confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1\ncement :6 coarse sand) etc complete | 5.907 | cum | |
| 76 | 3.16 | 2.25\nFilling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not\nexceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m\nand lift up to 1.5 m. | 5.67 | cum | |
| 77 | 3.17 | 4.1.8\nProviding and laying in position cement concrete of specified grade excluding the cost of centering and\nshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40\nnominal size) | 0.552 | cum | |
| 78 | 3.18 | 50.6.2.2\nSolid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size\nconfirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM\n1:6 ( 1 cement : 6 coarse sand) etc complete | 2.37 | cum | |
| 79 | 3.19 | 9.48.2\nProviding and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or\nround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden\nframes with rawl plugs screws etc | 251.401 | kg | |
| 80 | 3.2 | 13.62.1\nPainting with synthetic enamel paint of approved brand and manufacture of required colour to give an\neven shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of\napproved brand and manufacture . | 13.94 | m2 | |
| 81 | 3.21 | 13.1.1\n12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 42.681 | m2 | |
| 82 | 3.22 | 13.43.1\nApplying one coat of water thinnable cement primer of approved brand and manufacture on wall\nsurface:Water thinnable cement primer | 42.681 | m2 | |
| 83 | 3.23 | 13.60.1\nWall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two\nor more coats on new work | 42.681 | m2 | |
| 84 | 4 | WORKSHED NO 3 | |||
| 85 | 4.01 | 15.14.1\nDismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height\nincluding stacking the material within 50 metres lead:Of sectional area 40 square centimetres and above | 0.949 | cum | |
| 86 | 4.02 | 15.28.2\nDismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50\nmetres lead of :Asbestos Sheet | 111.227 | m2 | |
| 87 | 4.03 | 2.8.1\nEarth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation\ntrenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and\nramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus\nexcavated soil as directed, within a lead of 50 m.All kinds of soil | 17.493 | cum | |
| 88 | 4.04 | 50.2.25.1\nFilling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers\nnot exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to\n50 m and lift up to 1.5 m as per direction of site Engineer-in-charge | 24.632 | cum | |
| 89 | 4.05 | 4.1.8\nProviding and laying in position cement concrete of specified grade excluding the cost of centering and\nshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40\nnominal size) | 1.875 | cum | |
| 90 | 4.06 | 50.6.2.1\nSolid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available\nsize confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1\ncement :6 coarse sand) etc complete | 20.082 | cum | |
| 91 | 4.07 | 50.6.2.2\nSolid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size\nconfirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM\n1:6 ( 1 cement : 6 coarse sand) etc complete | 9.766 | cum | |
| 92 | 4.08 | 13.1.1\n12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 231.492 | m2 | |
| 93 | 4.09 | 13.43.1\nApplying one coat of water thinnable cement primer of approved brand and manufacture on wall\nsurface:Water thinnable cement primer | 231.292 | m2 | |
| 94 | 4.1 | 14.1.1\nRepairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including\ncutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls\ncomplete, including disposal of rubbish to the dumping ground within 50 meters lead:With cement mortar\n1:4 ( 1 cement : fine sand) | 20 | m2 | |
| 95 | 4.11 | 13.60.1\nWall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two\nor more coats on new work | 231.292 | m2 | |
| 96 | 4.12 | 5.47.3\nProviding and fixing in position factory made precast RCC M-40 doors and win frames having excellent\nsmooth finish as per IS:6523 with reinforcement of 3 Nos, 6 mm dia main bars tied with 3 mm M.S\nstirrups placed @ 200 mm CC nad 6 numbers high strength polymer blocks of required size for fixing\nhinges including providing 6 no specially designed M.S galvanised sleeves for accomodating 6 mm dia\nfully threaded bolts for fixing hold fast on vertical members, providing suitable arrangement for receiving sliding door bolts and tower bolt etc all complete, as per the direction of Engineer in charge. (The cost of\nhold fast and cc block of 1:3:6 mix is also included in the item.) The frame shall be measured in running\nmeter correct to two places of decimal.Door frame 85 mm x 60mm | 12.6 | mtr | |
| 97 | 4.13 | 9.20.1\nProviding and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core\nof block board construction with frame of I st class hard wood and well matched teak 3 ply veneering with\nvertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI\nmarked Stainless Steel butt hinges with necessary screws | 4.411 | m2 | |
| 98 | 4.14 | od108052/2018_2019\nSupplying and fixing approved Quality ready made single paneled PVC door frame with shutter to suit the\nopenings include all cost of materials and labour charges for fabrication and fixing in position etc.\ncomplete | 1.681 | m2 | |
| 99 | 4.15 | 21.1.1.2\nProviding and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up\nstandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :\n733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the\ngaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.\nAluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever\nrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel\nscrews, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing,\npaneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) | 18.225 | kg | |
| 100 | 4.16 | 21.3.1\nProviding and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM\nrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -\nin -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0\nmm thickness | 4.051 | kg | |
| 101 | 4.17 | 21.14\nProviding and fixing anodised aluminium ( anodised transparent or dyed to required shade according to\nIS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with\nextruded built up standard tubular section of approved make conforming to IS: 733 and IS: 1285, fixed\nwith dash fastener of required dia and size (Dash fastener to be paid for separately) | 18.225 | kg | |
| 102 | 4.18 | 9.48.2\nProviding and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or\nround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden\nframes with rawl plugs screws etc | 430.44 | kg | |
| 103 | 4.19 | 13.62.1\nPainting with synthetic enamel paint of approved brand and manufacture of required colour to give an\neven shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of\napproved brand and manufacture . | 21.445 | m2 | |
| 104 | 4.2 | 10.16.2\nSteel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including\ncutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding\nand bolted with special shaped washers etc. complete.Hot finished seamless type tubes | 2266.7 | kg | |
| 105 | 4.21 | 12.50\nProviding and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as\napproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams\nper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and\npolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to\navoid scratches during transportation and should be supplied in single length upto 12 metre or as desired\nby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)\nwith EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of\npurlins, rafters and trusses and including cutting to size and shape wherever required | 188.892 | m2 | |
| 106 | 4.22 | 12.51.1\nProviding and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total\ncoated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc\ncoating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both\nside of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws\ncomplete:Ridges plain (500-600 mm) | 23.85 | mtr | |
| 107 | 4.23 | od105863/2018_2019\nSupplying and fixing 200mm dia pvc half cut section with brackets at end of sheets or tiled roof rain water\ncollection including all cost of materials,conveyance and labour charges etc,complete | 47.7 | mtr | |
| 108 | 4.24 | 13.52.1\nFinishing with Epoxy paint (two or more coats) at all locations prepared and applied as per\nmanufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On\nsteel work | 94.446 | m2 | |
| 109 | 4.25 | 11.3.1\nCement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a\nfloating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.\ncomplete.40 mm thick with 20 mm nominal size stone aggregate | 44.42 | m2 | |
| 110 | 4.26 | 11.41.2\nProviding and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)\nwith water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and\nshades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints\nwith white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. | 10.531 | m2 | |
| 111 | 4.27 | 11.36\nProviding and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be\nspecified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green,\nblack of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm\nthick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg\nper sqm, including pointing in white cement mixed with pigment of matching shade complete. | 12.72 | m2 | |
| 112 | 4.28 | 11.37\nProviding and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the\nmanufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory,\nGrey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including\npointing the joints with white cement and matching pigment etc., complete. | 2.22 | m2 | |
| 113 | 4.29 | 15.12.1\nDismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats,\narchitrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below | 1 | each | |
| 114 | 4.3 | 17.3.1\nProviding and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10\nlitre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm\nflush bend, overflow arrangement with specials of standard make and mosquito proof coupling of\napproved municipal design complete, including painting of fittings and brackets, cutting and making good\nthe walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid | 1 | each | |
| 115 | 4.31 | 50.17.1.5\nSupplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of\nmaterials and labour charges etc complete as per the direction of site Engineer-in-charge. | 1 | no | |
| 116 | 4.32 | 18.54.1\nProviding and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 86 mm long,\nweighing not less than 88 gms | 1 | each | |
| 117 | 4.33 | 18.55.1\nProviding and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long,\nweighing not less than 88 gms | 1 | each | |
| 118 | 4.34 | 18.56.2\nProviding and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore, 125 mm long\nfoam flow, weighing not less than 120 gms | 1 | each | |
| 119 | 4.35 | 50.18.9.8.1\nProviding and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching,\nrefilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2 | 6 | mtr | |
| 120 | 4.36 | 50.18.9.9.1\nProviding and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching,\nrefilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2 | 6 | mtr | |
| 121 | 4.37 | 50.18.9.18.1\nProviding and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This\nincluded jointing of pipes with one step PVC solvent cement and testing of joints complete as per\ndirection of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall | 6 | mtr | |
| 122 | 4.38 | 50.18.7.3.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall | 20 | mtr | |
| 123 | 4.39 | 50.18.7.4.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall | 20 | mtr | |
| 124 | 4.4 | 50.18.8.3.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall\netc. 25 mm pipe 12 kgf/cm2 | 10 | mtr | |
| 125 | 4.41 | 50.18.8.4.1\nProviding and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This\nincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as\nper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall\nPRICE EST NO:2019/131\nprinted on etc. 32 mm pipe 10Kgf/cm2 | 10 | mtr | |
| 126 | 4.42 | 50.18.9.22.2\nProviding and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110 mm dia 45 degree Elbow | 1 | no | |
| 127 | 4.43 | 50.18.9.22.3\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement-110 mm dia Door Elbow | 1 | no | |
| 128 | 4.44 | 50.18.9.22.4\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement- 110 mm dia Bend | 1 | no | |
| 129 | 4.45 | 50.18.9.22.5\nProviding and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC\nsolvent cement 110x110x110 mm dia Tee | 1 | no | |
| 130 | 4.46 | 50.18.9.22.6\nProviding and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement - 110x110x110 mm dia Door tee | 1 | no | |
| 131 | 4.47 | 50.18.9.22.8\nProviding and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC\nsolvent cement -110 mm dia Vent cowl | 1 | no | |
| 132 | 4.48 | 17.7.1\nProviding and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste\nof standard pattern, including painting of fittings and brackets, cutting and making good the walls\nwherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass\npillar taps | 1 | each | |
| 133 | 4.49 | 18.48\nProviding and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked,\nwith cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow\npipes but without fittings and the base support for tank. | 1000 | ltr | |
| 134 | 4.5 | od107089/2018_2019\nSupplying and fixing ready made RCC Septic tank of size 200cm x 60 cm and soak pit , including all cost\nof materials,labour and onveyance charges etc.complete. | 1 | each | |
| 135 | 5 | WORKSHED NO 4 | |||
| 136 | 5.01 | 2.8.1\nEarth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation\ntrenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and\nramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus\nexcavated soil as directed, within a lead of 50 m.All kinds of soil | 16.758 | cum | |
| 137 | 5.02 | 50.2.25.1\nFilling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers\nnot exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to\n50 m and lift up to 1.5 m as per direction of site Engineer-in-charge | 42.282 | cum | |
| 138 | 5.03 | 50.6.2.1\nSolid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available\nsize confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1\ncement :6 coarse sand) etc complete | 19.238 | cum | |
| 139 | 5.04 | 4.1.8\nProviding and laying in position cement concrete of specified grade excluding the cost of centering and\nshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40\nnominal size) | 1.796 | cum | |
| 140 | 5.05 | 5.1.3\nProviding and laying in position specified grade of reinforced cement concrete, excluding the cost of\ncentering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse\nsand : 4 graded stone aggregate 20 mm nominal size) | 1.418 | cum | |
| 141 | 5.06 | 5.22.6\nSteel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and\nbinding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more | 141.75 | kg | |
| 142 | 5.07 | 50.6.2.2\nSolid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size\nconfirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM\n1:6 ( 1 cement : 6 coarse sand) etc complete | 0.92 | cum | |
| 143 | 5.08 | 13.1.1\n12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) | 24.591 | m2 | |
| 144 | 5.09 | 13.43.1\nApplying one coat of water thinnable cement primer of approved brand and manufacture on wall\nsurface:Water thinnable cement primer | 9.2 | m2 | |
| 145 | 5.1 | 13.60.1\nWall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two\nor more coats on new work | 9.2 | m2 | |
| 146 | 5.11 | 9.48.2\nProviding and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or\nround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden\nframes with rawl plugs screws etc | 96.6 | kg | |
| 147 | 5.12 | 11.3.1\nCement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a\nfloating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc.\ncomplete.40 mm thick with 20 mm nominal size stone aggregate | 93.961 | m2 | |
| 148 | 5.13 | 10.16.2\nSteel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including\ncutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding\nand bolted with special shaped washers etc. complete.Hot finished seamless type tubes | 1315.39 | kg | |
| 149 | 5.14 | 12.50\nProviding and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as\napproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams\nper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and\npolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to\navoid scratches during transportation and should be supplied in single length upto 12 metre or as desired\nby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)\nwith EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of\npurlins, rafters and trusses and including cutting to size and shape wherever required | 109.616 | m2 | |
| 150 | 5.15 | od105863/2018_2019\nSupplying and fixing 200mm dia pvc half cut section with brackets at end of sheets or tiled roof rain water\ncollection including all cost of materials,conveyance and labour charges etc,complete, | 27 | mtr | |
| 151 | 5.16 | 13.52.1\nFinishing with Epoxy paint (two or more coats) at all locations prepared and applied as per\nmanufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On\nsteel work | 109.616 | m2 | |
| 152 | 6 | ELECTRICAL | |||
| 153 | 6.01 | 1.10.2\nWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated\ncopper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch,\nmodular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper\nconductor single core cable etc as required.Group B | 8 | point | |
| 154 | 6.02 | 1.10.3\nWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated\ncopper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch,\nmodular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper\nconductor single core cable etc as required.Group C | 3 | point | |
| 155 | 6.03 | 1.14.1\nWiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated\ncopper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire | 30 | mtr | |
| 156 | 6.04 | 1.14.2\nWiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated\ncopper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5\nsq. mm + 1 X 2.5 sq. mm earth wire | 10 | mtr | |
| 157 | 6.05 | 1.21.1\nSupplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/\nrecess including cutting the wall and making good the same in case of recessed conduit as required.20\nmm | 80 | mtr | |
| 158 | 6.06 | 1.21.2\nSupplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/\nrecess including cutting the wall and making good the same in case of recessed conduit as required.25\nmm | 10 | mtr | |
| 159 | 6.07 | 1.23.1\nSupplying and fixing following piano type switch / socket on the existing switch box/ cover including\nconnections etc. as required.5/6 amps switch | 3 | each | |
| 160 | 6.08 | 1.23.4\nSupplying and fixing following piano type switch / socket on the existing switch box/ cover including\nconnections etc. as required.3 pin 5/6 amp socket outlet | 3 | each | |
| 161 | 6.09 | 1.23.3\nSupplying and fixing following piano type switch / socket on the existing switch box/ cover including\nconnections etc. as required.15/16 amp switch | 1 | each | |
| 162 | 6.1 | 1.23.5\nSupplying and fixing following piano type switch / socket on the existing switch box/ cover including\nconnections etc. as required.6 pin 15/16 amp socket outlet | 1 | each | |
| 163 | 6.11 | 1.27.3\nSupplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular\nswitches in recess etc as required.4 Module (125mmX75mm) | 2 | each | |
| 164 | 6.12 | 1.27.5\nSupplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular\nswitches in recess etc as required.8 Module (125mmX125mm | 2 | each | |
| 165 | 6.13 | 1.17.2\nSupplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the\nexisting surface / recessed steel/ PVC conduit as required.2 x 1.5 sq. mm | 50 | mtr | |
| 166 | 6.14 | 1.33\nSupplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding\nconnection etc as required. | 11 | each | |
| 167 | 6.15 | 2.10.1\nSupplying and fixing 5 amps to 32 amps rating, 240/415 volts, \"C\" curve, miniature circuit breaker\nsuitable for inductive load of following poles in the existing MCB DB complete with connections, testing\nand commissioning etc. as required.Single pole | 4 | each | |
| 168 | 6.16 | 2.14.2\nSupplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residualcurrent\ncircuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB\ncomplete with connections, testing and commissioning etc. as required.40 amps | 1 | each | |
| 169 | 6.17 | 2.3.2\nSupplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V,\non surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,\ninterconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8\nway, Double door | 1 | each | |
| 170 | 6.18 | od109240/2018_2019\nSupply and fixing of 18W 4 feet LED Tube fitting for use on 240V AC supplying including all accessories,\nclamp, base etc. Required for fixing etc. Complete of good quality and approved make | 11 | each | |
| 171 | 6.19 | od109244/2018_2019\nSupply and fixing sheet steel three phase energy meter panel board in the existing wall on surface /\nrecess complete with copper busbar, neutral busbar, earth bar powder coated including earthing etc. as\nrequired.(without energy meter) | 1 | each | |
| 172 | 6.2 | od109245/2018_2019\nsupply, fixing, tesing and commissioning of 63A Three phase energy meter in the existing meter panel\nboard. with fuse. | 1 | each | |
| 173 | 7 | WELL | |||
| 174 | 7.01 | Lump-Sum Total | 1 | NO |
AI Tender Summary
Tender Timeline
Jan 06, 2020
11:30 IST
Tender Published
Tender notice published.
CompletedJan 13, 2020
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 15, 2020
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender