| 1 | 072191200B | HUMIDITY CHAMBER RH 60% | Spec:: Specifications: Humidity chamber specification:(Analysis of coal for Equilibrated moisture equipment work at RH 60% & Temp 40 degree specification complies) Chamber volume: 285 liters; cubic feet: 10; Internal size cms:57*57*88; External size cms:70*85*166; Shelves:2; Range Temperature +20 degree C to 60 degree C; Controller accuracy: +/- 0.5 C of set value for temperature; Uniformity: +/- 1 C throughout chamber; Heater element: Special type SS tubular air heaters with fins; Heat up time: 3 min upto 60 degree C; Cool down time: 40 min upto + 50 degree C without load; Cooler: plate fin without load; Compressor: Hermetically sealed brand new compressor; Controller: Digital display electronic controller; Sensor: Platinum 100; Humidity in % RH with 0.1 degree C and 0.1% RH resolution; Chlorofluorocarbons (CFC) free cooling refrigerant used for cooling purpose with safe guarded by time delay circuit; Audio and Video alarms are generated for temperature/Humidity variation; Also with safety facility for temperature and humidity over /short, in case controlling system fails; The unit works on 230 volts AC and 50 Hz main supply. External: Mild steel powder coated/stainless steel; Inner Acrylic door: Inner flow size see through acrylic 8mm thick; Circulation: Motorized blown from back; Safety device: Adjustable hydraulic over temperature limit protection; PID control: Microprocessor based PID controller; RH 60% and Temp 40 C Variable adjustment; The equipment shall be calibrated and be supplied with calibration certificate; Cyclic timer: 0 to 24 hrs *7 days cyclic ON/OFF timer for illuminating part; Supplied with stabilizer and sufficient capacity | No | 1 |
| 2 | 073010200B | PRIMARY CRUSHER (HAMMER MILL TYPE) | Spec:: Specifications: Chamber size: 560x 400 mm, Feed size: 250 mm (Max.); Output Size: 12.5 mm(max); Production Capacity:1000Kg/Hr; Hardness of the sample: To crush coal/stone (aggregated); 6.Motor: 15 HP,440 volts,3 phase,50 Hz, AC mains; Hammers : Made up of Forged steel; Breaker plate: Made of Manganese steel; Complete with electric motor, starter and V belt Spares to be supplied: Starter -1 no.; V belts-2 sets; Hammers -2 Sets; Bearings- 1 set. | No | 1 |
| 3 | 073010301B | SECONDARY CRUSHER HAMMER TYPE | Spec:: Specifications: Chamber size : 450 x 150 mm; Feed Size : 12.5 mm (approximately); Output size : 3 mm (shall not > 3.0 mm); Production capacity : 500 Kg/Hr; Hardness of sample : To crush coal / stones; Motor : 10 HP, 440 Volts, 3 Phase, 50 Hz, A.C. Mains; Hammers : made of Forged Steel; Breaker Plate : made of Manganese Steel; Complete with Electric Motor, Starter, and V-Belt; Dust absorption System - NOT REQUIRED Spares to be supplied: Starter- 1 No.; V-belts - 2 set; Hammers-2 set; Bearings - 1 set. | No | 1 |
| 4 | 073030100Y | PULVERISER: MINI MILL(RYMOND MILL TYPE) | Spec:: Specifications: Suitable for grinding coal samples or similar hard and dry materials. It shall be with duly hardened OHNS with Swing-Hammers pivoted around the circumference of the mill rotor which is directly mounted on to the motor shaft. The swing- hammers shall rotate in the grinding chamber, which is inlaid with ratchet teeth liner on top and the perforated steel screens at the bottom with delivery trough. Mill shall be mounted on a Heavy-Duty Angle Iron stand. TECHANICAL SPECIFICATION: Grinding chamber : M.S. fabricated Hammers : OHNS, duly hardened, 58-60 MOH Scale Sieve : Woven Screen with perforated backup screen Feed size : 3 mm Product size : 212 microns (IS 72 mesh)passing through sieves Feeder : Hand operated Screw Feeder Motor : 0.5 HP, 3 Phase Starter : DOL type of L&T, BCH, Siemens make. Power : 415 V, 50 Hz, 3 phase, AC Mains Spares to be supplied: Starter -1 no.; Swing hammer - 2 sets | Nos | 2 |
