| 1 | 1 | M & L for carrying out chemical analysis of water as per IS- 10500- 2012 from any govt Approved lab/Institute after collecting the water sample(FIFTEN NO) in separate suitable container as prescribed by the labs from following each pump house / borewell complete all as specified and directed by Engr-in-Charge :-\n(a) 9 Sqn Pump House\n(b) ETB PUMP HOUSE\n(c) BOMBDUMP pump house\n(d) Logistic Pump House\n(e) NOR Pump House\n(f) SOR pump House\n(g) Tech Flt Pump House\n(h) HQ Pum House\n(j) Old CSD Pump House\n(k) BPCL Pump House\n(l) 1 Sqn Pump House\n(m) ‘A’ Flt pump House\n(o) CCR Pump House\n(p) Singpur range pump House\n | | 1 | Each Job |
|---|
| 2 | 2 | M&L for Cleaning of Static Water Tank 50,000 Gallon capacity of any description, dewatering & cleaning inside of the SWT by removing all despositions/fungus , other micro organism , sediment loose dirt/mud sludge, Vegetation , other foreign materials etc and also removing loose/unsound concrete/plaster including taking out and removing all disposal waste / spoil to a distance not exceeding 50 mtr and Brushing with nylon brush on walls & bottom surfaces , washing the cleaned surfaces with water and washing repeatedly with Rebekiense solution and clean with water & cleaning of external surafce with water, including two coats of white wash on internal surfaces and exposed external surface & clearance of any vegetation growth atlest 2 mt around the swt to the satisfaction of Engr-in-Charge complete all as specified and directed | | 19 | Each |
|---|
| 3 | 3 | Disconnecting the existing non functional submersible pump set from supply, dismantling existing CI bend from non return valve, removing and lifting out submersible pump set of any description and capacity and in any position, alongwith existing column pipe 80/50mm dia and existing submersible cable of any size from the bore well (approximately 50 mtr depth of pump set from GL) complete and lowering after repair with all accessories including testing all as specified and directed.\nNOTE:- 1. Contractor shall take proper precautions while lifting out and removing motor/pump set from bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost. Any items like cable, column pipe, clamps shall be paid separately. \n2 . Any repair to submersible pump & spares etc shall be paid and measured separately under relavant item in this schedule | | 10 | Each |
|---|
| 4 | 4 | Dismantling and strip opening of submersible pump/motor of any description of Capacity up to 20 HP for reparing /overhauling, fixing of serviceable parts in position, removing & replacement of defective / unserviceable parts with new parts (To be paid separately) including minor parts such as washer, 'O' Rings, nut bolts and any machining work required re-threading of holes, lock nut etc required for smooth functioing of pump motor and reassembling the pump and motor, ensuring proper alignment of pump and motor,complete all as directed. Note: - (i) The replacement of defective / unserviceable parts shall be measured and paid separately as “Supply only” under appropriate item of Sch ‘A’ and fixing rate for new items are deemed to include under these item. \n(ii) Burnt out windings of motor shall be replaced, measured and paid separately under appropriate item of Sch ‘A’ for rewinding. | | 7 | Each |
|---|
| 5 | 5 | Supply only the following items / parts of AC submersible motor/pump of above mentioned types and capacity complete all as specified and directed:- | | | |
|---|
| 6 | 5.01 | Upper & lower rubber housing bush | | 50 | Each |
|---|
| 7 | 5.02 | Stainless steel rotor sleeve. | | 20 | Each |
|---|
| 8 | 5.03 | Thrust bearing complete set. | | 7 | Each |
|---|
| 9 | 5.04 | MS Flange with stud. | | 10 | Each |
|---|
| 10 | 5.05 | Motor base of cast iron. | | 3 | Each |
|---|
| 11 | 5.06 | Neck Ring . | | 50 | Each |
|---|
| 12 | 5.07 | Pump Key | | 20 | Each |
|---|
| 13 | 5.08 | Sim wisher | | 100 | Each |
|---|
| 14 | 5.09 | Segment holder assembly. | | 4 | Each |
|---|
| 15 | 5.1 | Strainer. | | 7 | Each |
|---|
| 16 | 5.11 | Oil seal. | | 14 | Each |
|---|
| 17 | 5.12 | Coupling set with key of stainless steel | | 7 | Each |
|---|
| 18 | 5.13 | Discharge outlet of cast iron for pump | | 6 | Each |
|---|
| 19 | 5.14 | Rotor For 15 to 20 HP Submersible motor. | | 1 | Each |
|---|
| 20 | 5.15 | Stage casing of Cast Iron | | 14 | Each |
|---|
| 21 | 5.16 | Gun metal body bush. | | 50 | Each |
|---|
| 22 | 5.17 | Impellar | | 55 | Each |
|---|
| 23 | 5.18 | Rotor machining,grinding and balancing | | 4 | Each |
|---|
| 24 | 5.19 | Motor tube boring,machining & reconditioning | | 7 | Each |
|---|
| 25 | 5.2 | motor lamination setting with material | | 7 | Each |
|---|
| 26 | 5.21 | Rotor reconditioning | | 3 | Each |
|---|
| 27 | 5.22 | slote repairing in stator | | 7 | Each |
|---|
| 28 | 5.23 | Stainless steel distance bush ( Spacer). | | 50 | Each |
|---|
| 29 | 5.24 | Inlet bracket | | 4 | RM |
|---|
| 30 | 5.25 | Cable Guard | | 14 | Each |
|---|
| 31 | 5.26 | Stainless Steel Connection Piece (Adopter Piece) | | 6 | Each |
|---|
| 32 | 5.27 | Cast iron Suction Housing including studs | | 1 | Each |
|---|
| 33 | 5.28 | Rotor up to 12.5 HP Submersible motor. | | 1 | Each |
|---|
| 34 | 5.29 | SS Pump shaft suitable up to 12.5 HP complete all as specified and directed. | | 2 | Each |
|---|
| 35 | 5.3 | SS Pump shaft suitable for 15 to 20 HP complete all as specified and directed. | | 1 | Each |
|---|
| 36 | 6 | S & F flat copper conductor submersible cable of size 6 Sqmm, 3 core complete all as specified and directed. | | 300 | RM |
|---|
| 37 | 7 | GI socket, heavy duty, seamless, long threaded ISI marked for 80mm bore column pipes all as directed by Engineer-in-Charge. | | 20 | Each |
|---|
| 38 | 8 | All as per item no. 7.00 above but 50 mm dia | | 5 | Each |
|---|
| 39 | 9 | Supply only Galvanised iron medium grade 3.00 mtr long 80 mm bore colum pipe both ended threaded and long socket complete oll as directed. | | 22 | Each |
|---|
| 40 | 10 | Supply only Galvanised iron medium grade 3.00 mtr long 50 mm bore colum pipe both ended threaded and long socket complete oll as directed. | | 5 | Each |
|---|
| 41 | 11 | Taking out and removing old burnt out windings of the submersible electric motors 15/20 HP, 3 Phase, 415 Volts of following capacity and re winding of submersible electric motors with existing size super enamel insulated, copper winding wire including cleaning the slots with carbon- tetra-chloride solution before re winding including repairing of stator including grinding, re condintioning required lamination insulation material etc complete all as specified and directed. | | 4 | Each job |
|---|
| 42 | 12 | All as per item No.11.00 above but submersible electric motor of 10 /12.5 HP | | 2 | Each job |
|---|
| 43 | 13 | All as per item No.11.00 above but submersible electric motor of 5 /7.5 HP | | 1 | Each job |
|---|
| 44 | 14 | Repair to stage casing outer & inner diffuser of submersible pump of any description by cutting,balancing, brazing , welding, turning and Grinding complete all as specified and directed for the following capacities of the pumps coupled with submersible motors of capacity 15 to 20 HP | | 2 | Each job |
|---|
| 45 | 15 | All as per item No.14.00 above but submersible pump capacity upto 5.0 to 12.5 HP | | 5 | Each job |
|---|
| 46 | 16 | Supply fabrication & installation out door type MS Cover fabricated panel with 3.15 mm thick CRCA sheet duly painted with two coats of synthetic enamelled paint over a coat of red oxide primer of suitable size mounted on MS angle iron of 50X50X6 mm and having 4 legs of 1.00 mtr incl grouting in PCC 1:3:6 up to 100 Amps MCCB 4 Pole 25 KA Make Legrand DPX Model-01 No and Star delta Starter cum pump controller fully automatic in sheet )-01 No including metal enclosure MUG type 3 Phase,415 Volt AC Cat part No MUG 30 (CS 96008)-01 No including connected with copper cable of suitable size all as directed. | | 1 | Each |
|---|
| 47 | 17 | Supply fabrication & installation out door type MS Cover fabricated panel with 2.00 mm thick CRCA sheet duly painted with two coats of synthetic enamelled paint over a coat of red oxide primer of suitable size mounted on MS angle iron of 50X50X6 mm and having 4 legs of 1.00 mtr incl grouting in PCC 1:3:6 up to 63 Amps MCCB 4 Pole 25 KA Make Legrand DPX Model-01 No and Star delta starter cum pump controller fully automatic in sheet )-01 No including metal enclosure MUG type 3 Phase,415 Volt AC Cat part No MUG 20 (SS 95975)-01 No including connected with copper cable of suitable size all as directed. | | 1 | Each |
|---|
| 48 | 18 | Supply and fixing steel wire rope flexible type 5 mm connect with submrsible pump set in bore well depth 40 mtr and tested complete all as specified and directed. NOTE; Pump Set lowering and lifting charges paid separately\n | | 400 | RM |
|---|
| 49 | 19 | M&L for construction of brick masonry valve pit / chamber complete with 3mm thick MS sheet cover with locking arrangement of size 600 mm x 600 mm x 600 mm (depth) (internal dimensions) all as shown on CE(AF)/TD/EM/01 Sheet 1/1 dt 16 Mar 1993 with and including necessary excavation & earth work in any type of soil complete all as specified and directed. | | 4 | Each |
|---|
| 50 | 20 | M&L for construction of brick masonry valve pit / chamber complete with 3mm thick MS sheet cover with locking arrangement of size 7500 mm x 750 mm x 750 mm (depth) (internal dimensions) all as shown on CE(AF)/TD/EM/01 Sheet 1/1 dt 16 Mar 1993 with and including necessary excavation & earth work in any type of soil complete all as specified and directed. | | 4 | Each |
|---|
| 51 | 21 | M&L for construction of brick masonry valve pit / chamber complete with 3mm thick MS sheet cover with locking arrangement of size 1050 mm x 1050mm x 1050 mm (depth) (internal dimensions) all as shown on CE(AF)/TD/EM/01 Sheet 1/1 dt 16 Mar 1993 with and including necessary excavation & earth work in any type of soil complete all as specified and directed. | | 4 | Each |
|---|
| 52 | 22 | M& L for repairing of leaked lead joint by taking out lead and making lead joint by retrived lead and extra lead if required with new spun yarn and caulking including necessary excavation and earth work, bailing out water etc complete all as specified and directed for the following sizes :-\n | | | |
|---|
| 53 | 22.01 | 150mm | | 30 | Each |
|---|
| 54 | 22.02 | 100mm | | 40 | Each |
|---|
| 55 | 22.03 | 80mm | | 50 | Each |
|---|
| 56 | 23 | Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep, in any type of soil including forming sides and bottom surfaces to required level / slope / gradients etc for taking down/laying of the pipe lines complete all as specified and directed at site. | | 260 | Cum |
|---|
| 57 | 24 | Returning, filling in, excavated soil in trenches, including spreading, leveling, watering and well ramming in layers of thickness not exceeding 25 cm complete all as specified and directed. | | 234 | Cum |
|---|
| 58 | 25 | Removing excavated surplus soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed. | | 26 | Cum |
|---|
| 59 | 26 | Disconnecting and taking down old existing steel tubing and connections of any description/ grade and in any position in trenches/under floors / on walls etc including all fittings/accessories and fixtures such as bends, union,elbow socket etc complete all as specified and directed for the following sizes :-\n | | | |
|---|
| 60 | 26.01 | 80 mm bore | | 200 | RM |
|---|
| 61 | 26.02 | 50 mm bore | | 200 | RM |
|---|
| 62 | 26.03 | 40 mm bore | | 200 | RM |
|---|
| 63 | 26.04 | 25 mm bore | | 200 | RM |
|---|
| 64 | 26.05 | 20 mm bore | | 200 | RM |
|---|
| 65 | 26.06 | 15 mm bore\nNote:- Excavation & earth work shall be measured and paid separetely under respective item of Sch 'A'. | | 100 | RM |
|---|
| 66 | 27 | Supply, laying, jointing and testing galvanized iron water tubing, medium grade, including all necessary GI fittings /accessories laid in trenches complete all as specified and directed for the following sizes:-\n | | | |
|---|
| 67 | 27.01 | 80 mm bore | | 200 | RM |
|---|
| 68 | 27.02 | 50 mm bore | | 200 | RM |
|---|
| 69 | 27.03 | 40 mm bore | | 200 | RM |
|---|
| 70 | 27.04 | 25 mm bore | | 200 | RM |
|---|
| 71 | 27.05 | 20 mm bore | | 200 | RM |
|---|
| 72 | 27.06 | 15 mm bore\n | | 100 | RM |
|---|
| 73 | 28 | Taking up or down existing cast iron sluice valves of any description and in any position, removing from site including taking out joints complete all as specified and directed for the following sizes\n | | | |
|---|
| 74 | 28.01 | 150 mm bore | | 4 | Each |
|---|
| 75 | 28.02 | 100 mm bore | | 4 | Each |
|---|
| 76 | 28.03 | 80 mm bore | | 4 | Each |
|---|
| 77 | 29 | Supply, installation, fixing, jointing and testing, ISI Marked, cast iron sluice valve of class PN-1 conforming to IS-14846 of 2000 both ends flanged with iron wheel head and stainless steel spindle, jointed with and including jointing material such as rubber or fibre gasket, nuts, bolts washers etc and tested complete all as specified and directed for following bores :- \n | | | |
|---|
| 78 | 29.01 | 150 mm bore | | 3 | Each |
|---|
| 79 | 29.02 | 100 mm bore | | 3 | Each |
|---|
| 80 | 29.03 | 80 mm bore | | 4 | Each |
|---|
| 81 | 30 | Taking up or down exiting cast iron non return valve of 100 mm bore in any position, removing from site including taking out joints complete all as specified and directed. | | 4 | Each |
|---|
| 82 | 31 | All as per item No. 30.00 above but 80 mm bore. | | 4 | Each |
|---|
| 83 | 32 | Supply and fixing, 100mm bore, ISI Marked, cast iron non return valve, both ends flanged, jointed with and including jointing material such as rubber or fibre gasket, nuts, bolts, washers etc and tested complete all as specified and directed.\n | | 4 | Each |
|---|
| 84 | 33 | Supply and fixing, 80mm bore, ISI Marked, cast iron non return valve, both ends flanged, jointed with and including jointing material such as rubber or fibre gasket, nuts, bolts, washers etc and tested complete all as specified and directed.\n | | 4 | Each |
|---|
| 85 | 34 | Taking out old unservicable rotational moulded polyethyiene water storage tanks 2000 ltrs cylindrical with closed top hoisted and all as specified and directed\n | | 1 | Each |
|---|
| 86 | 35 | Taking out old unservicable rotational moulded polyethyiene water storage tanks 500 ltrs cylindrical with closed top hoisted and all as specified and directed\n | | 1 | Each |
|---|
| 87 | 36 | Supply and fixing rotational moulded polyethyiene water storage tanks 2000 ltrs cylindrical with closed top hoisted and fixed in position all as specified and directed\n | | 1 | Each |
|---|
| 88 | 37 | All as per item No. 36.00 above but 500 ltrs | | 1 | Each |
|---|
