Supply Of Mechanical Engineering Labs And Related Equipments
Tender Value
2.10 Crore
Estimated cost
Bid Submission
05 Dec 2019
0 days left
EMD
6.30 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Raisen and Lateri → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Supply Of Mechanical Engineering Labs And Related Equipments - Static & Dynamic Balancing Apparatus , Cam And Follower Apparatus , Universal Vibration Apparatus , Universal Governor Apparatus , Single Cyliner Multi Fuel Vcr Engine With Dynamometer Testrig With Smoke Analyser Computerized Engine Test Set-Up For Variable Compression Ratio Multifuel Engine., Hand Held Flue Gas Analyzer, Parameter Measuring Range Oxygen : 0 To 21%, Fuel Supply System Model, 8 Cooling System Model The Models Displays The The Working And Components Used In The Cooling Of An Automobile Engines. 9 Ignition System Model The Models Displays The The Working And Components Used In The Ignition System Of An Automobile 10 Lubrication System Model The Models Displays The The Working And Components Used In The Lubricating System Of An Automobile Engine. 11 Fuel Pump Model The Models Displays The The Working And Components Of Fuel Pump Used In Ic Engines 12 Fuel Injector Model The Models Displays The The Working And Components Of Fuel Injector. 13 Different Types Of Carburetor Models : The Models Displays The The Cut Section Of Different Carburetors: Single Stage Single Barrel, Two Stage Single Barrel Or Two Stage Two Barrel Throttling And Seperating Calorimeter Apparatus15 Models Of Different Types Of Steam Condenser The Models Displays The The Working And Components Of Steam Condenser 16 Models Of Different Types Of Steam Nozzeles The Models Displays The The Working And Components Of Steam Nozzles. ( Fixed Dia, Vari=Ying Dia , Determination Of Cd, Cc And Cv Orifice And Mouthpiece Apparatus :, Notch Tank Apparatus , Jet On Vane Appartus , Combined Pipe Friction Measurement Appartus, Venturimeter And Orificemeter Apparatus, Bernoullis Apparatus, Metacentric Height Apparatus , 24 Models Of Different Pipe Joints The Models Displays The Various Type Of Pipe Joints Used In The Pipelines 25 Models Of Different Types Of Water Pumps The Models Displays The Various Type Of Pumps Used In Water Flow System. It Could Be Centrifugal Pump, Magnetic Pump, Peristaltic Pump Etc Pelton Wheel Turbine Test Rig, Models Of Piezometer And Different Types Of Monometer , Pitot Tube Apparatus To Determine Discharge, Hydraullic Test Bench, Kaplan Turbine Test Rig, Francis Turbine Test Rig, Link Polygon Apparatus, 33 Simple Wheel And Axle The Wheel And Axle Is A Machine Consisting Of A Wheel Attached To A Smaller Axle So That These Two Parts Rotate Together In Which A Force Is Transferred From One To The Other. A Hinge Or Bearing Supports The Axle, Allowing Rotation. It Can Amplify Force; A Small Force Applied To The Periphery Of The Large Wheel Can Move A Larger Load Attached To The Axle 34 Screw Efficiency Apparatus A Jackscrew, Or Screw Jack, Is A Type Of Jack That Is Operated By Turning A Leadscrew. It Is Commonly Used To Lift Moderately Heavy Weights, Such As Vehicles; To Raise And Lower The Horizontal Stabilizers Of Aircraft; And As Adjustable Supports For Heavy Loads, Such As The Foundations Of Houses 35 Automotive Lighting This Apparatus Displays The Arrangement Of Lighting System Used In Automobiles. All The Required Accessories Are Displayed On The Panel Board For Study 36 Automotive Electrical Circuit The Demonstration Board Which Will Give A Complete Idea Of The Electrical System Of Maruti Car. In This Demonstration Board The Actual Wiring With The Parts And Accessories Of A Car Had Been Arranged, According To The Electrical Circuit Of The Car And Terminals Are Connected To The Battery . Automotive Electronic Circuit, Vehicle Displays Principles Systems Trainer, Ignition And Charging System, Digital Multimeter, Tungsten Inert Gas Welding Machine ( Tig ) ., Tungsten Inert Gas Welding Machine ( Tig ) ., Impact Testing Machine., Radial Drilling Machine., 45 Metal Arc Welding Machine Three Phase, 380 V, Igbt Technology Based, Cooling Mode: Air Cooled, Output Current:300-400 A, Invertor Based, Stainless Steel Material, Galvanised Surface. Hydraulic Power Hacksaw, Universal Testing Machine. ( 100 Tonnes ) Capacity: 1000 Kn, Multi Cylinder Four Stroke Water Cooled Diesel Engine Test Rig, Cnc Milling Trainer Machine, Heat Pump Apparatus, Reynolds Apparatus, Rockwell Cum Brinell Hardness Testing Machine ( Digital ) , Robotic Arm Trainer With Pc Interface, Lathe Machine. 5.5 Feet Bed Length, Power Pipe Cutter Cut Off Machine, Hand Grinder, 58 Pedestral Grinding Machine 1 Hp 3 Phase 2800 Rpm Pedestal Grinder With Grinding Wheels Size 10” X 1, 2 No. Wheel ( One Fine & One Coarse ) At Each End, Fitted With Wheel Guard, Tool Rest & Cast Iron Leg Shaper Machine. 18 Heavy Duty All Geared Type Shaping Machine, , Forge Furnance , 61 Carpentry Shop - Carpentry Vices Rules Straight Edge Try Square Mitre Square , Bevel Square Combination Square Marking Knife Mortise Gauge Cutting Gauge Wing Compass Trammel Divider Calliper Spirit Level Plumb Bob Rip Saw Cross-Cut Saw Panel Saw Tenon Or Back Saw Dovetail Saw Bow Saw Coping Saw Compass Saw Pad Or Keyhole Saw Firmer Chisel Beveled Edge Chisel Paring Chisel Morise Chisel Gouges Chisel Jack Plane Trying Plane Smoothing Plane Rebate Plane, Plough Plane Spokeshave Metal Jack Plane Router Gilmet Bradawl Ratchet Brace Wheel Brace Drill Bit Twist Bit Expansion Bit Centre Bit Forstner Bit Countersink Bit Warrington Hammer Claw Hammmer Ball Pin Hammer Straight Hammer Mallet Bench Hold Fast Sash Cramp G-Cramp Hand Screw Rasps Files Scraper Oil Stone Glass Paper Pincer, 62 Sheet Metal Shop, 63 Smithy Shop, 64 Fitting Shop, 65 Welding Shop, 66 Plastic Moulding Shop
BOQ
| Name of Work: ANNEXURE-10: SPECIFICATIONS OF EQUIPMENTS FOR MECHANICAL ENGG. LAB | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Description of Item | |||
| 2 | 1.01 | Static & Dynamic balancing Apparatus Drive Motor: FHP Motor, variable speed, with speed controller. Balancing weight: 4 Nos. of Stainless Steel with different sized eccentric mass for Varying unbalance.\nRotating Shaft: Material Stainless Steel\nSupplied with Instruction Manual\n | item1 | 1 | Nos |
| 3 | 2.01 | Cam and Follower Apparatus Cam Shaft : Material Stainless Steel\nCams: Tangent, Eccentric, Circular Arc, made of hardened alloy – steel.\nFollowers: Roller, Knife edge, Mushroom, made of hardened alloy – steel.\nCompression Spring : Provided\nWeights : 1 kg., 500gm, 200 gm & 100gm\nMotor : Variable speed DC Motor with speed controller\nDial Gauge : Baker & Mercer/Standard Make\nSupplied with Instruction Manual\n | item2 | 1 | Nos |
| 4 | 3.01 | Universal Vibration apparatus Exciter Unit : With FHP DC Motor with Speed Control Facility\nRPM measurement: Digital RPM Indicator with Proximity sensor.\nOrdinary Chart recorder: For recording Frequency and Amplitude of Vibration.\nStop Watch: Electronic Stop Watch.\nSupplied with Instruction Manual\n | item3 | 1 | Nos |
| 5 | 4.01 | universal Governor Apparatus Watt governor,porter governor,proell governor and Hartnell governor Spindle : Material Stainless Steel\nGovernor Mechanism\nMotor: Variable speed, Standard Make, FHP Motor.\nControl Panel: For speed control of motor.\nSupplied with Instruction Manual | item4 | 1 | Nos |
| 6 | 5.01 | Single cyliner multi fuel VCR engine with dynamometer testrig with smoke analyser COMPUTERIZED ENGINE TEST SET-UP FOR VARIABLE COMPRESSION RATIO MULTIFUEL ENGINE. ENGINE: Type - Single Cylinder, Four-Stroke, Spark / Compression Ignition Variable Compression Ratio Engine Alternative Fuel Development for S.I. & C.I. engines. MECHNISM –In this engine, the compression ratio is to be varied by a mechanism which involves Raising or lowering the total head assembly including the valves, camshaft etc. The linear movement of the head assembly should be measureable Precisely by a Depth micrometer / Plunger Dial and this reading can be used directly to calculate compression ratio directly by means of Graph & Table provided & also by inputting the value in the software IT SHOULD BE POSSIBLE TO VARY Compression Ratio continuously FROM 5 :1 TO 22:1 Without dismantling or changing the Cylinder Head Technical Specifications: - Bore X Stroke – Approximately 87.5 mm X 110 mm Rated Capacity – 6.5 B.H.P. @ 1500 RPM when using High Speed Diesel @ CR 17.5:1 or Better Compression Ratio Adjustable from – 5:1 to 11:1 FOR SPARK IGNITION MODE & 12:1 to 22:1 FOR COMPRESSION IGNITION MODE Water Cooled engine.Fuel Delivery: - Carburettor for SI Mode & Fuel Injection Pump for CI mode Ignition timing for SI Mode 50º BTDC to 10º ATDC Starting – Thro The Dynamometer Compression is to be adjustable even when the engine is running. The flywheel MUST BE calibrated in Degrees to allow accurate measurement of ignition timing, using stroboscopic light method. An adjustment is provided so that the ignition timing, can be adjusted while the engine is running. B. DYNAMOMETER – Air Cooled AC Regenerative Dynamometer with Load Cell type Weighing Mechanism & Max Torque above 60 N-m Accuracy is < 0.25 % of Full Scale Torque of Dyno. RPM indicator is supplied with the dynamometer. C. Common Base Frame: - The engine and dynamometer are mounted on a Common Rigid Channel Frame, which can be directly mounted on the foundation block D. Cardan Shaft: A Suitable Cardan Shaft for connecting Engine to Dynamometer is provided E. Cardan Shaft Guard for protection from rotating shaft | item5 | 1 | Nos |
| 7 | 6.01 | Hand Held Flue Gas Analyzer For measurement O2,CO, CO2 (cal.), NO, SO2, diff. pressure,\nTemperature and velocity measurement.\nWith built-in printer and dataloger.\nComplete with 50cm or 100cm long sampling probe with 3 meter long\nsampling hose, filter assembly, battery charger, instruction manual\ndatalogging software, carrying case and calibration certificate.\n with sensors Parameter Measuring range \nOxygen : 0 to 21%\nCO : 0 to 8000 ppm\nNO : 0 to 5000 ppm\nSO2 : 0 to 5000 ppm\nCO2 : 0 to 99% calculated\nTemp. : 0 to 1250 oC\nDiff. pressure : ±200 mbar\nVelocity measurement : 0- 97 m/sec | item6 | 1 | Nos |
| 8 | 7.01 | Fuel supply system model The models displays the fuel supply system on board. All the components are shown separately on the board and connected with a line to show how it works | item7 | 1 | Nos |
| 9 | 8.01 | Cooling system model The models displays the the working and components used in the cooling of an automobile engines. | item8 | 1 | Nos |
| 10 | 9.01 | Ignition system model The models displays the the working and components used in the ignition system of an automobile | item9 | 1 | Nos |
| 11 | 10.01 | Lubrication system model The models displays the the working and components used in the lubricating system of an automobile engine. | item10 | 1 | Nos |
| 12 | 11.01 | Fuel pump model The models displays the the working and components of fuel pump used in IC engines | item11 | 1 | Nos |
| 13 | 12.01 | Fuel injector model The models displays the the working and components of fuel injector. | item12 | 1 | Nos |
| 14 | 13.01 | Different types of carburetor models : The models displays the the cut section of different carburetors: Single stage single barrel, two stage single barrel or two stage two barrel | item13 | 1 | Nos |
| 15 | 14.01 | Throttling and seperating calorimeter apparatus Separating Chamber :Compatible capacity made of Stainless Steel insulated with Ceramic wool with water level indicator.\nThrottling Chamber :Compatible capacity provided with gauge to measure in let Pressure before throttling\nHeat Exchanger : For Condensing steam after throttling chamber Steam Generator : Compatible capacity with digital temperature controller tocontrol the temperature inside the steam generator.\nDifferential pressure : By manometer Measurement\nSteam pressure measurement: By Pressure gauge\nAn ENGLISH instruction manual consisting of experimental procedures, block diagram etc.will be provided along with the Apparatus\nThe whole set – up is well designed and arranged on a rigid structure painted with Paint.All the temperature should be displayed at one time on 2004 JUMBO GRAPHICAL DISPLAY with assistance of micro-controller.\n | item14 | 1 | Nos |
| 16 | 15.01 | Models of different types of steam condenser The models displays the the working and components of STEAM CONDENSER | item15 | 1 | Nos |
| 17 | 16.01 | Models of different types of steam nozzeles The models displays the the working and components of STEAM Nozzles. ( FIXED DIA, VARI=YING DIA etc.) | item16 | 1 | Nos |
| 18 | 17.01 | Determination of Cd,Cc and Cv Orifice and Mouthpiece Apparatus : Set of Orifices: Material Acrylic (2 Nos.) Dia. 10mm and 15 mm\nSet of Mouthpieces: Material Acrylic (3 Nos.)\nDia 10 mm (L/D = 1)\nDia 10 mm (L/D = 2.5)\nDia 10 mm (L/D = 4)\nConstant Head tank: 35 Ltrs.\nPointer Gauge: To measure X-Y co-ordinates of Jet.\nWater Circulation: FHP Pump, Crompton make.\nFlow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 70 Ltrs.\nStop Watch: Electronic.\nControl Panel Comprises of :\nStandard make On/Off Switch, Mains Indicator, etc.\nSupplied with Instruction Manual \nwith the Apparatus Tanks will be made of Stainless Steel.\nThe whole set-up is well designed and arranged in a good quality painted structure | item17 | 1 | Nos |
| 19 | 18.01 | Notch Tank Apparatus Channel Test Section: Size 600 x 250 x 180 mm.\nNotches : Material Brass\nRectangular Notch\n45° V Notch\n60° V Notch\nPointer Gauge : With Vernier scale.\nWater Circulation: FHP Pump Crompton makes.\nFlow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 50 Ltrs.\nStop Watch: Electronic.\nControl Panel Comprises of :\nStandard make On/Off Switch, Mains Indicator, etc.\nSupplied with Instruction Manual\nThe whole set-up is well designed and arranged in a good quality painted structure\n | item18 | 1 | Nos |
| 20 | 19.01 | Jet on Vane Appartus Target (2 Nos.) : Flat Plate and Hemispherical Cup\nNozzle : Material Brass\nJet Enclosure : Made of Acrylic \nWater Circulation : FHP Pump, Standard make\nFlow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 50 Ltrs.\nStop watch: Electronic.\nControl Panel Comprises of :Standard make On/Off Switch, Mains Indicator, etc.Supplied with Instruction Manual Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure | item19 | 1 | Nos |
| 21 | 20.01 | Combined Pipe Friction Measurement Appartus Pipe Test Section: \n(i) Dia ½”, Length : 1m, Material G.I.\n(ii) Dia ¾”, Length: 1.25m, Material G.I.\nWater Circulation: FHP Pump, Crompton/godrej/G.E makes.\nFlow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 50 Ltrs.\nStop Watch: Electronic.\nControl Panel Comprises of :\nStandard make On/Off Switch, Mains Indicator, etc.\nSupplied with Instruction Manual \nwith the Apparatus Tanks will be made of Stainless Steel. \nThe whole set-up is well designed and arranged in a good quality painted structure | item20 | 1 | Nos |
| 22 | 21.01 | Venturimeter and Orificemeter Apparatus Venturimeter: Material Clear Acrylic compatible to 1” Dia. Pipe.\nOrifice meter : Orifice plate made of Stainless Steel and housing made of Clear \nAcrylic compatible to 1” Dia. Pipe.\nPitot tube set up made of stainless steel/Copper of compatible size fitted with vernier scale and housing made of clear Acrylic section compatible to 1” dia. Pipe. \nWater Circulation: FHP Pump, Crompton make.\nFlow Measurement: Using Measuring Tank with Piezometer (Capacity 25 Ltrs.) and Electronic Stop Watch FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons. Sump Tank: Capacity 50 Ltrs. Control Panel Comprises of:\nStandard make On/Off Switch, Mains Indicator, etc. Supplied with Instruction Manual, Tanks will be made of Stainless Steel. The whole set-up is well designed and arranged in a good quality painted structure | item21 | 1 | Nos |
| 23 | 22.01 | Bernoullis Apparatus Test Section: Material Acrylic (One Piece).\nPiezometer Tubes: Material P.U. Tubes (7 Nos.)\nWater Circulation: FHP Pump, Crompton make.\nFlow Measurement: Using Measuring Tank with Piezometer, Capacity 25 Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 70 Ltrs.\nInlet Tank: Capacity 20 Ltrs.\nStop Watch: Electronic.\nControl Panel Comprises of:\nStandard make On/Off Switch, Mains Indicator, etc.\nTanks will be made of Stainless Steel.\nSupplied with Instruction Manual\nThe whole set-up is well designed and arranged in a good quality painted structure | item22 | 1 | Nos |
| 24 | 23.01 | Metacentric Height Apparatus Pontoon: Size 300 x 300 mm (approx.) with a Horizontal \nGuide Bar for aliding weight and Removable Strips, \nGraduated Arc with Pointer with moveable hanger and set of weights.\nWater Tank : Size 550 x 500x 400 mm (approx.)\nFront Window of Tank : Made of Glass/Perspex.\nA set of weights is supplied with the apparatus.\nSupplied with Instruction Manual\nTanks will be made of Stainless Steel.\nThe whole set-up is well designed and arranged in a good quality painted structure | item23 | 1 | Nos |
| 25 | 24.01 | Models of different pipe joints The models displays the various type of pipe joints used in the pipelines | item24 | 1 | Nos |
| 26 | 25.01 | Models of different types of water pumps The models displays the various type of Pumps used in water flow system. It could be centrifugal pump, magnetic pump, peristaltic pump etc | item25 | 1 | Nos |
| 27 | 26.01 | Pelton wheel turbine Test Rig Output Power: 1 kW.\nDischarge: 400 LPM (Approx.)\nSupply Head: 25 m\nSpeed: 1000 RPM (Approx.)\nNozzle: Material Stainless Steel.\nSpear: Material Stainless Steel. \nDynamometer: Rope Brake type.\nSump Tank: Capacity 200 Ltrs.\nWater Circulation: Centrifugal Pump, Standard make, Capacity 5 HP, \nThree Phase, 2800 RPM\nDischarge Measurement: Pitot tube with Manometer\nAll pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller.\n Tanks will be made of Stainless Steel.\nThe whole set-up is well designed and arranged in a good quality painted structure\n | item26 | 1 | Nos |
| 28 | 27.01 | Models of Piezometer and different types of monometer The models displays the various type of Manometer that can be put into the use for the measurement of pressure change | item27 | 1 | Nos |
| 29 | 28.01 | Pitot tube apparatus to determine discharge Pitot tube: Material Copper/SS of compatible size fitted with vernies scale.\nTest Section: Material Clear Acrylic, compatible to 1” Dia. Pipe.\nWater Circulation: FHP Pump, Crompton make.\nFlow Measurement: Using Measuring Tank with Piezometer (Capacity 25 Ltrs.) and Electronic Stop Watch FLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons.\nSump Tank: Capacity 50 Ltrs.\nControl Panel Comprises of :\nStandard make On/Off Switch, Mains Indicator, etc.\nSupplied with Instruction Manual \nTanks will be made of Stainless Steel.\nThe whole set-up is well designed and arranged in a good quality painted structure | item28 | 1 | Nos |
| 30 | 29.01 | Hydraullic Test Bench Top Tray : Size 1000 x700 x 100mm(approx)\nWater Circulation : 1 HP Pump, Crompton/Kirlo skar make.\nFlow Measurement : Using Measuring Tank, Capacity 40Ltrs.\nFLOW SENSOR with digital display along with on board calibrtion facility with the help of buttons\nSump Tank : Capacity100Ltrs.\nStopWatch : Electronic.\nControl Panel Comprises of : Standard make On/Off Switch, Mains Indicator, etc.\nTanks and Top Tray will be made of Stainless Steel.\nSupplied with Instruction Manual\nThe whole set-up is well designed and arranged on a rigid structure painted with Paint\n | item29 | 1 | Nos |
| 31 | 30.01 | Kaplan turbine Test Rig Output Power : 1 kW.\nDischarge : 1000 LPM\nSupply Head : 5-8 M\nNormal Speed : 2000 RPM\nDynamometer : Rope Brake type.\nWater Circulation : Centrifugal Pump, CRI/Standard Make, Capacity 5 HP, 3 Phase.\nDischarge Measurement : Pitot Tube with Manometer\nAll pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller\nSump Tank : Capacity 200 Ltrs.\nPressure Measurement : Pressure Gauge & Vacuum Gauge \nPiping & Fittings : Pipes & fittings with flow control valves of suitable size Tanks will be made of Stainless Steel.\nThe whole set-up is well designed and arranged in a good quality painted structure | item30 | 1 | Nos |
| 32 | 31.01 | Francis Turbine Test Rig Output Power : 1 KW\nDischarge : 1000 LPM (Approx.)\nSupply Head : 10 m (Approx.)\nSpeed : 1000 RPM (Approx.)\nRunner: Having Curved Vanes.\nDynamometer: Rope Brake type.\nSump Tank: Capacity 200 Ltrs.\nWater Circulation: Centrifugal Pump, Standard Make, Capacity 5 HP Three Phase.\nDischarge Measurement : Pitot Tube with Manometer\nAll pressure and RPM value should be displayed on 2004 JUMBO Graphical Display with assistance of microcontroller\nControl Panel Comprises of : L&T make Starter, Mains Indicator, MCB for overload protection. \nSupplied with Instruction Manual \nTanks will be made of Stainless Steel. \nThe whole set-up is well designed and arranged in a good quality painted structure | item31 | 1 | Nos |
| 33 | 32.01 | Link polygon apparatus The apparatus is provided with five linkages and connectors, having hooks to which pans are hung.These are fixed between two pulleys around which rope is run to connect to two extension type spring balances. The unit is very useful for the study of arches, abutments and piers. The wooden rectangular beam is fitted with scale.With weights. | item32 | 1 | Nos |
| 34 | 33.01 | Simple wheel and axle The wheel and axle is a machine consisting of a wheel attached to a smaller axle so that these two parts rotate together in which a force is transferred from one to the other. A hinge or bearing supports the axle, allowing rotation. It can amplify force; a small force applied to the periphery of the large wheel can move a larger load attached to the axle | item33 | 1 | Nos |
| 35 | 34.01 | Screw efficiency apparatus A jackscrew, or screw jack, is a type of jack that is operated by turning a leadscrew. It is commonly used to lift moderately heavy weights, such as vehicles; to raise and lower the horizontal stabilizers of aircraft; and as adjustable supports for heavy loads, such as the foundations of houses | item34 | 1 | Nos |
| 36 | 35.01 | Automotive Lighting This apparatus displays the arrangement of lighting system used in automobiles. All the required accessories are displayed on the panel board for study | item35 | 1 | Nos |
| 37 | 36.01 | Automotive Electrical Circuit The demonstration board which will give a complete idea of the electrical system of maruti car. In this demonstration board the actual wiring with the parts and accessories of a car had been arranged, according to the electrical circuit of the car and terminals are connected to the battery . | item36 | 1 | Nos |
| 38 | 37.01 | Automotive Electronic circuit Electronic ignition system is a working model designed to demonstrate the students operation of a typical electronic system used in the car. The trainer consists of ignition coil, distributor, set of spark plugs and 12 V DC supply. | item37 | 1 | Nos |
| 39 | 38.01 | Vehicle Displays Principles systems Trainer This trainer is designed to teach students principles of Vehicle Display System and warning systems through comprehensive practical activities. The activities include instrument cluster, fuel system warning system, engine sensor warning system, automotive lighting instrumentation, passenger safety warning system, ABS failure warning system and engine failure warning system | item38 | 1 | Nos |
| 40 | 39.01 | Ignition and charging system This apparatus displays the spark plug used for ignition and the related accessories. Also the Charging system is also explained in the model | item39 | 1 | Nos |
| 41 | 40.01 | Digital Multimeter 3 ¾ Digit, 3100 Counts, Auto Power Off, Auto / Manual Ranging, Continuity, Diode Check, \n Warning for Blown Fuse & Overload Condition,\nAutomatic Terminal Blocking System, Min / Max Value Storage, Data Hold, \nDigital cum Analog Bar graph Indication, Bat low Indication\nAC Voltage: 30 mV – 1000 V, \nDC Voltage: 3 V – 1000 V,\nAC Current: 300 uA – 10 A, \nDC Current: 3 mA – 10 A,\nResistance: 30 Ohm – 30 MOhm,\nCapacitance: 30 nF – 30 uF,\nFrequency: 300 Hz – 100 kHz,\nTemperature: -200 to +850 Deg C (Pt 100/ Pt1000 input)\nBasic Accuracy: 0.1 %/ 0.25 % \nOperable with 9 V battery \nHolster of Soft Rubber for shock & drop protection, \nElectromagnetic Compatibility ( EMC ), IP 50 & IP 20 Protections, \nSupplied with set of lead, user manual, test & Calibration certificate, Rubber Holster, Carrying belt, , | item40 | 1 | Nos |
| 42 | 41.01 | Tungsten Inert Gas Welding Machine(TIG). voltage 415 volt,frequency 50Hz,range output:5-35 Amp,DC max 74 volt,Adjustable clean ratio for perfect perfect aluminium welding,spot welding digital display,5 different ac waveform output synchronous mutual arc feature optimal water cooled,water cooling machine.1 power source,product type AC/DC with electrode holder,pulse TIG.,TIG torch,input current 20 Amp & output current 315 amp,cable length 3 metre. | item41 | 1 | Nos |
| 43 | 42.01 | CNC turning trainer machine \nSwing over bed: more than 110 mm\nSwing over carriage: more than 60 mm\nDistance between centers: more than 420 mm\nHole through spindle: 10 mm\nSpindle nose thread: 3/4\"-16 T.P.I .\nSpindle nose taper: #1 Morse \nTravel of crosslide: more than 100 mm\nTaper of tailstock spindle: #0 Morse.\nProtractor graduations: 0° to 45° by 5°\nHandwheel graduations: .0.01 mm\nMotor: 90 Volt DC with electronic speed control, input 220V/50Hz. \nSpindle speed range: 70-2800 RPM continuously variable by electronic eed control\nCNC stepper motor holding torque: 136 oz-in\nRapid travel speed, X and Z: 22 inches/min\nThe system enclosed in a metallic enclosure , openable front door, acrylic front and side cover and display panel.\nHaving coolant system with removable collector.\nSystem Having mechanical storage system on the bottom for Computer system, Controller and for Electrical wiring.\nThe system shall be supplied withPC, Optical Mouse, 17” TFT Monitor & Keyboard. | item42 | 1 | Nos |
| 44 | 43.01 | Impact Testing Machine. Pendulum drop Angle:(140 degree for Charpy test)& (90 degree for Izod test),Pendulum Impact energy:300J (Charpy test) & 168J for Izod test,striking velocity of pendulum:2.45m/sec. for charpy test & 3.857 m/sec. for Izod test.,Scale graduation:2J,Max. permissible less by friction :0.50% of Impact energy. | item43 | 1 | Nos |
| 45 | 44.01 | Radial Drilling Machine. Heavy Duty, Radial Drilling Machine - 25mm Cap / 8 Speed / 200mm Travel with FINE FEED Attachment Column, arm, work head & gears made out of closed grain, spindle ram is made out of alloy steel & main spindle & pinon are made of EN forged steel drilling capacity : 25 mm, column dia : 127 mm, Spindle nose : MT-3, Spindle travel : 200 mm, speed : 110-2880 RPM, Ram dia : 72 mm, drilling radius : 660 mm, drillling head motor : 1 hp (1440 rpm), lifting of arm motor : 0.5 HP, Dist. from spindle to base : 810/130, Dist. from column to spindle : 620/350, supplied with Electrical such as 1 HP 1440 RPM 3 phase Ele. Motor for Drilling 0.5 HP 1440 RPM 3 phase Ele. Motor for Lifting R/F switch 2 Nos. V-Belt 2 Nos. with Fitting… : 1 No. Box Table [250x205x205mm] , ½” Drill Chuck , ½” Arbour , 2/3” Sleeve , 6” Drill Vice | item44 | 1 | Nos |
| 46 | 45.01 | Impact Testing Machine. Impact Testing M/C (Charpy/Izod) Works on pendulum principle, Difference between heights of drop of pendulum before Rupture & Height of rise after Rupture of specimen is directly proportional to impact energy absorbed. Direct indication of impact energy absorbed by specimen on large dial. Confirms to BS 131 part IV-1972 & BSEN 10045-2:1993\nMax. capacity: 300 Joule Min. scale graduation: 2 Joule\n | item45 | 1 | Nos |
| 47 | 46.01 | Metal Arc Welding Machine Three phase,380 V,IGBT technology based,cooling mode: Air cooled,output current:300-400 A,invertor based,stainless steel material,Galvanised surface. | item46 | 1 | Nos |
| 48 | 47.01 | Hydraulic Power Hacksaw Perfectly toothed to cut metal sheets,Continous hydraulic system for facilating and lifting operation,optimal floor space.No. of stroke per minute:80,Electric motor:1 HP,Capacity of round bar:8'',Capacity of square bar:6''Blade size:16*1.25\",Stroke:5.75\"size:8\" | item47 | 1 | Nos |
| 49 | 48.01 | Universal Testing Machine.(40 /100 tonnes) Capacity: 400/1000 KN\nMechanical Model\nLoading accuracy as high as ±1%.\nTraining roll autographic recorder supplied as standard to enable study of the behavior of materials, High reading accuracy due to large size and design of dial.Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens.\nMotorised loading and unloading cycle.\nLarge effective clearance between columns enables testing of standard specimens as well as structures.\nSimple controls for ease of operation.\nSafe operation ensured by means of safety devices.\nFully enclosed and protected pendulum. | item48 | 1 | Nos |
| 50 | 49.01 | Universal Testing Machine.(100 tonnes) Capacity: 1000 KN\nMechanical Model\nLoading accuracy as high as ±1%.\nTraining roll autographic recorder supplied as standard to enable study of the behavior of materials, High reading accuracy due to large size and design of dial.Wide range of standard and special accessories, including load stabilizer. Easy change from plain to threaded and screwed specimens.\nMotorised loading and unloading cycle.\nLarge effective clearance between columns enables testing of standard specimens as well as structures.\nSimple controls for ease of operation.\nSafe operation ensured by means of safety devices.\nFully enclosed and protected pendulum. | item49 | 1 | Nos |
| 51 | 50.01 | Multi Cylinder Four Stroke Water Cooled Diesel Engine Test Rig\nFour cylinder, four stroke engine, vertical water cooled, self start, diesel engine.\nEddy Current Dynamometer\nThe engine coupled with Eddy Current Dynamometer with resistance loading arrangement. Digital voltmeter ,digital ammeter are provided.Digital techometer also provided.\nweighing gear, control gear, a dead weight in Kg unit suitable for testing the engine at different speeds. The engine and dynamometer are directly coupled on a substantial base plate. \nFuel measuring system of a fuel tank, a burette and a three way cock arrangement.\nAir tank with orifice and water manometer.\nMeasurement of Heat carried\nInlet outlet piping with flow control valve, water away by Cooling water meter. Thermometers are provided to measure the inlet outlet temperature of water. Common Base Frame: - The engine and dynamometer are mounted on a Common Rigid Channel Frame, which can be directly mounted on the foundation block . | item50 | 1 | Nos |
| 52 | 51.01 | CNC milling trainer machine Stepping Resolution: 0.003mm Mechanical repeatability : 0.01mm\nSpindle Speed : 1100 - 11000 RPM\nTravel: X = 300mm, Y = 146mm, Z = 153mm\nRapid Travel of 30 in/min.\nUniversal Standard G-Code import.\nPlugs directly into computer printer port.\nPrecision Mechanics.\nBox way Z-axis assembly with ground steel plate and tapered brass gib.\nAdjustable tapered brass gib on X-axis.\nGround steel sliding ways with adjustable brass gib.\nHard anodized aluminum table.\n1/2\" (12.7mm) 20 pitch Cr-Mo lead dscrews with adjustable split bronze nuts on all axes.\nThe system should be installed in a metallic enclosure with at least 5' height, openable front door, acrylic front and side cover and display panel.Having coolant system with removable collector.\nSystem having mechanical storage system on the bottom for Computer system, Controller and for Electrical wiring.\nThe system supplied with PC Optical Mouse, 17” TFT Monitor & Keyboard.\nThe complete system included with: MicroMill with Powerful 1/4 HP spindle motor, Pulley set with drive belt, 1/8\" (3mm) or 3/16\" (4mm) or 1/4\" (6mm) collet with collet closer, Electronic Chopper Driver Unit, Custom Win 7 Mach 3 control software interface, 4th Axis Amplifier and Port Included, Input/Output Port Included, 200 oz-in. stepping motors, Printer cable, power cable etc.\n | item51 | 1 | Nos |
| 53 | 52.01 | Heat pump Apparatus Compressor: Hermitically sealed compressor. Capacity 1/3 Ton, Condenser: Water cooled type shell and coil condenser with refrigerant inside the tube. \nWater flow measurement: Provided with individual rota meters and four temperature Sensor for both condenser and evaporator. Expansion Valve: Capillary Tube, Compatible Capacity. Safety Control: Overload and over current protectors for compressor and \nTime Delay circuit. Evaporator: Water cooled Compatible capacity. Temperature Sensor: RTD PT-100 Type. Control Panel comprises of: Digital Voltmeter: 0-300 V Digital Ammeter: 0-5 Amp. Temperature Measurement: Digital Temperature Indicator with multi-channel switch.Supplied with Instruction Manual All the accessories will be mounted on a rigid base frame made of M.S. and it will be powder coated. ? All the temperature should be displayed at one time on 2004 JUMBO GRAPHICAL DISPLAY with assistance of micro-controller | item52 | 1 | Nos |
| 54 | 53.01 | Rockwell cum Brinell Hardness Testing Machine (Digital) (Hardness tester for Metal like steel, copper, brass, aluminum etc)\n(Readings on Digital screen in HRC or HRB Scale—For Rockwell Test )\n(For Brinell Test -Manually measure the indentation diameter by using Brinell Microscope and Brinell hardness table).\nMajor Loads :-Rockwell Loads :60,100,150 kgf\nBrinell Load : 187.5 , 250 kgf\nMinor load for Rockwell : 10 kgf\nIndentor : Diamond and 1/16’’ ball\nindentor For Rockwell test and 2.5 and 5\nmm Ball Indentor for Brinell Test\nMaximum test height : 230 mm\nDepth of throat : 133 mm\n50MM Flat table and 35mm vee groove table\nHRC /HRB/ HBW Test block---1 no Each\nAccording to IS:1586:2000 | item53 | 1 | Nos |
| 55 | 54.01 | ROBOTIC ARM TRAINER WITH PC INTERFACE The robotic arm interface kit connects Robotic Arm Trainer to a personal computer,.The software for the interface permits real time control and contains a built-in interactive script writer.\nA user may write a script that contains up to 99 individual robotic arm functions (including pauses) into a single script file. Script files may be saved and loaded from disk just like any other standard computer file.\nScript files may be replayed automatically up to 99 times for\ndemonstrating computer controlled automation and animatronics.\nThe Robotic Arm PC Interface provide learning and experimenting with computer automation and animatronics.\n \n\n\n | item54 | 1 | Nos |
| 56 | 55.01 | Lathe Machine. 5.5 Feet bed length High Precision Medium Duty Double V-Belt Drive Lathe Machine complete with all standards Accessories such as Chuck Plate, Gear Set, Center Adaptor, Dead Center, Dial Indicator, Square Tool Post, Tool Post Key with HARDENED BED Length of Bed : 5 ¼ ' , Height of Centre : 212 mm, Width of Bed. : 280 mm, Spindle Hollow : 52 mm, Admit Between Centers. : 725 mm Extra accessories: Electrical such as 2 HP 1440 RPM 3 Phase Electric Motor, Switch, V-Belt & Fittings, 8” x 3 Jaw Precision True Chuck with chuck plate, 12’ x 4 Jaw Dog Chuck with chuck plate, Face Plate , Follow Rest, Steady Rest | item55 | 1 | Nos |
| 57 | 56.01 | Power pipe cutter CUT OFF MACHINE 14” CUT – OFF Machine with 2 HP. 3 Phase Electric Motor, V - Belt, Fitting with Abrasive Wheel – 1 No. | item56 | 1 | Nos |
| 58 | 57.01 | Hand grinder Wheel Diameter (inch) 1\"/ 25mm\n Collet Chuck Size (mm) 6 mm\n Power Consumption (Watt) 520 W\n No Load Speed (rpm) 23000 to 30000\n Spindle Size 5/32\"- 14 | item57 | 1 | Nos |
| 59 | 58.01 | Pedestral Grinding Machine 1 HP 3 Phase 2800 RPM PEDESTAL GRINDER with Grinding Wheels Size\n 10” x 1\", 2 No. Wheel (one fine & one coarse) at each end, fitted with wheel guard, tool rest & cast iron leg | item58 | 1 | Nos |
| 60 | 59.01 | Shaper Machine. 18'' Heavy Duty ALL GEARED Type SHAPING MACHINE Machine Size: 18\", Maximum Stroke: 20\", Len of Ram: 36\"\nMax. dist. of Table to Ram: 15\"\nMin. dist. of table to Ram: 2\"\nMax. vertical travel to tool slide: 4\"\nLength & width of table top.: 18\" x 12\"\nLength & width of table slide: 30\" x 11\"\nLength of cross slide: 30\"\nWidth of Ram: 10\"\nNo of speeds: 3\nMain Motor Power: 2 HP, Fitted with Vice, Motor Pulley, Handle, Ram Back Tray & Automatic Lubrication Arrangement , Accessories : Electrical such as 2 HP 3 Phase 960 RPM Electric Motor, Starter, V-Belt & Fittings, Key way cutting attachment | item59 | 1 | Nos |
| 61 | 60.01 | Forge Furnance Maximum Temp.950°C, work on 220/230 v or 440 V AC, 3 phase supply | item60 | 1 | Nos |
| 62 | 95.01 | Carpentry shop Carpentry Vices | item61.1 | 20 | Nos |
| 63 | 96.01 | Rules | item61.2 | 30 | Nos |
| 64 | 97.01 | Straight edge | item61.3 | 20 | Nos |
| 65 | 98.01 | Try square | item61.4 | 20 | Nos |
| 66 | 99.01 | Mitre square | item61.5 | 20 | Nos |
| 67 | 100.01 | Bevel square | item61.6 | 20 | Nos |
| 68 | 101.01 | Combination square | item61.7 | 5 | Nos |
| 69 | 102.01 | Marking Knife | item61.8 | 20 | Nos |
| 70 | 103.01 | Mortise Gauge | item61.9 | 20 | Nos |
| 71 | 104.01 | Cutting gauge | item61.10 | 10 | Nos |
| 72 | 105.01 | Wing compass | item61.11 | 5 | Nos |
| 73 | 106.01 | Trammel | item61.12 | 10 | Nos |
| 74 | 107.01 | Divider | item61.13 | 10 | Nos |
| 75 | 108.01 | Calliper | item61.14 | 20 | Nos |
| 76 | 109.01 | Spirit level | item61.15 | 20 | Nos |
| 77 | 110.01 | Plumb bob | item61.16 | 5 | Nos |
| 78 | 111.01 | Rip saw | item61.17 | 20 | Nos |
| 79 | 112.01 | Cross-cut saw | item61.18 | 10 | Nos |
| 80 | 113.01 | Panel saw | item61.19 | 10 | Nos |
| 81 | 114.01 | Tenon or back saw | item61.20 | 20 | Nos |
| 82 | 115.01 | Dovetail saw | item61.21 | 10 | Nos |
| 83 | 116.01 | Bow saw | item61.22 | 5 | Nos |
| 84 | 117.01 | Coping saw | item61.23 | 5 | Nos |
| 85 | 118.01 | Compass saw | item61.24 | 5 | Nos |
| 86 | 119.01 | Pad or keyhole saw | item61.25 | 5 | Nos |
| 87 | 120.01 | Firmer chisel | item61.26 | 20 | Nos |
| 88 | 121.01 | beveled edge chisel | item61.27 | 20 | Nos |
| 89 | 122.01 | Paring chisel | item61.28 | 10 | Nos |
| 90 | 123.01 | Morise chisel | item61.29 | 10 | Nos |
| 91 | 124.01 | gouges chisel | item61.30 | 10 | Nos |
| 92 | 125.01 | Jack Plane | item61.31 | 20 | Nos |
| 93 | 126.01 | trying Plane | item61.32 | 5 | Nos |
| 94 | 127.01 | Smoothing plane | item62.1 | 10 | Nos |
| 95 | 128.01 | Rebate plane | item62.2 | 5 | Nos |
| 96 | 129.01 | Plough plane | item62.3 | 5 | Nos |
| 97 | 130.01 | Spokeshave | item62.4 | 5 | Nos |
| 98 | 131.01 | Metal jack plane | item62.5 | 10 | Nos |
| 99 | 132.01 | Router | item62.6 | 5 | Nos |
| 100 | 133.01 | Gilmet | item62.7 | 5 | Nos |
| 101 | 134.01 | Bradawl | item62.8 | 5 | Nos |
| 102 | 135.01 | Ratchet Brace | item62.9 | 5 | Nos |
| 103 | 136.01 | Wheel Brace | item62.10 | 5 | Nos |
| 104 | 137.01 | Drill bit | item62.11 | 5 | Nos |
| 105 | 138.01 | twist bit | item62.12 | 5 | Nos |
| 106 | 139.01 | Expansion bit | item62.13 | 5 | Nos |
| 107 | 140.01 | Centre bit | item62.14 | 5 | Nos |
| 108 | 141.01 | Forstner bit | item62.15 | 5 | Nos |
| 109 | 142.01 | Countersink bit | item62.16 | 5 | Nos |
| 110 | 143.01 | Warrington Hammer | item62.17 | 5 | Nos |
| 111 | 144.01 | Claw Hammmer | item62.18 | 5 | Nos |
| 112 | 145.01 | Ball pin Hammer | item62.19 | 20 | Nos |
| 113 | 146.01 | Straight hammer | item62.20 | 20 | Nos |
| 114 | 147.01 | Mallet | item62.21 | 20 | Nos |
| 115 | 148.01 | Bench hold fast | item62.22 | 2 | Nos |
| 116 | 149.01 | Sash cramp | item62.23 | 2 | Nos |
| 117 | 150.01 | G-cramp | item62.24 | 2 | Nos |
| 118 | 151.01 | Hand screw | item62.25 | 2 | Nos |
| 119 | 152.01 | Rasps | item62.26 | 20 | Nos |
| 120 | 153.01 | files | item62.27 | 20 | Nos |
| 121 | 154.01 | Scraper | item62.28 | 20 | Nos |
| 122 | 155.01 | Oil stone | item62.29 | 20 | Nos |
| 123 | 156.01 | Glass paper | item62.30 | 20 | Nos |
| 124 | 157.01 | Pincer | item62.31 | 10 | Nos |
| 125 | 158.01 | Cabinet Screw driver | item62.32 | 2 | Nos |
| 126 | 159.01 | Ratchet screw driver | item62.33 | 2 | Nos |
| 127 | 160.01 | Woodworking Lathe machine Operated with 1 HP motor & mounted on table top | item62.34 | 1 | Nos |
| 128 | 161.01 | Sheet Metal Shop Different snips | item63.1 | 20 | Nos |
| 129 | 162.01 | shears | item63.2 | 20 | Nos |
| 130 | 163.01 | stacks | item63.3 | 20 | Nos |
| 131 | 164.01 | latter | item63.4 | 20 | Nos |
| 132 | 165.01 | figure pucnh | item63.5 | 20 | Nos |
| 133 | 166.01 | solid pucnh | item63.6 | 20 | Nos |
| 134 | 167.01 | hollow pucnh | item63.7 | 20 | Nos |
| 135 | 168.01 | soft hammer | item63.8 | 20 | Nos |
| 136 | 169.01 | channel | item63.9 | 20 | Nos |
| 137 | 170.01 | square bars | item63.10 | 20 | Nos |
| 138 | 171.01 | standard sheet gauges | item63.11 | 20 | Nos |
| 139 | 172.01 | Mallet | item63.12 | 20 | Nos |
| 140 | 173.01 | Smithy shop Anvil | item64.1 | 8 | Nos |
| 141 | 174.01 | Swage block | item64.2 | 8 | Nos |
| 142 | 175.01 | Hand hammer | item64.3 | 10 | Nos |
| 143 | 176.01 | Ball peen hammer | item64.4 | 10 | Nos |
| 144 | 177.01 | Straigt peen hammer | item64.5 | 10 | Nos |
| 145 | 178.01 | cross pin Hammer | item64.6 | 10 | Nos |
| 146 | 179.01 | Flat tongs | item64.7 | 10 | Nos |
| 147 | 180.01 | Rivet or ring tongs | item64.8 | 10 | Nos |
| 148 | 181.01 | Straight-lip fluted tong | item64.9 | 10 | Nos |
| 149 | 182.01 | Gad tongs | item64.10 | 10 | Nos |
| 150 | 183.01 | Flat tongs | item64.11 | 10 | Nos |
| 151 | 184.01 | Flatter | item64.12 | 10 | Nos |
| 152 | 185.01 | fuller | item64.13 | 10 | Nos |
| 153 | 186.01 | Rivet header | item64.14 | 5 | Nos |
| 154 | 187.01 | Punch | item64.15 | 10 | Nos |
| 155 | 188.01 | Hot chisel | item64.16 | 10 | Nos |
| 156 | 189.01 | size plate or bush | item64.17 | 10 | Nos |
| 157 | 190.01 | cupping tool | item64.18 | 10 | Nos |
| 158 | 191.01 | different types and different size of dice and taps | item64.19 | 5 | Nos |
| 159 | 192.01 | Fitting Shop Fitting bench vice | item65.1 | 24 | Nos |
| 160 | 193.01 | leg vice | item65.2 | 4 | Nos |
| 161 | 194.01 | pipe vice | item65.3 | 4 | Nos |
| 162 | 195.01 | hand vice | item65.4 | 4 | Nos |
| 163 | 196.01 | pin wice | item65.5 | 4 | Nos |
| 164 | 197.01 | tool makers vice | item65.6 | 4 | Nos |
| 165 | 198.01 | hand hammer | item65.7 | 10 | Nos |
| 166 | 199.01 | ball peen hammer | item65.8 | 10 | Nos |
| 167 | 200.01 | cross peen hammer | item65.9 | 10 | Nos |
| 168 | 201.01 | straight peen hammer | item65.10 | 10 | Nos |
| 169 | 202.01 | soft hammer | item65.11 | 10 | Nos |
| 170 | 203.01 | flat chisel | item65.12 | 10 | Nos |
| 171 | 204.01 | cross cut chisel | item65.13 | 10 | Nos |
| 172 | 205.01 | half round chisel | item65.14 | 10 | Nos |
| 173 | 206.01 | diamond point chisel | item65.15 | 10 | Nos |
| 174 | 207.01 | side chisel | item65.16 | 10 | Nos |
| 175 | 208.01 | flat file | item65.17 | 20 | Nos |
| 176 | 209.01 | hand file | item65.18 | 10 | Nos |
| 177 | 210.01 | square file | item65.19 | 10 | Nos |
| 178 | 211.01 | pillar file | item65.20 | 10 | Nos |
| 179 | 212.01 | round file | item65.21 | 10 | Nos |
| 180 | 213.01 | triangular file | item65.22 | 10 | Nos |
| 181 | 214.01 | half round file | item65.23 | 10 | Nos |
| 182 | 215.01 | knife edge file | item65.24 | 10 | Nos |
| 183 | 216.01 | flat single cut and double cut file | item65.25 | 20 | Nos |
| 184 | 217.01 | triangulargle cut and double cut file | item65.26 | 10 | Nos |
| 185 | 218.01 | half round file | item65.27 | 10 | Nos |
| 186 | 219.01 | care off scraper | item65.28 | 10 | Nos |
| 187 | 220.01 | surface plate | item65.29 | 10 | Nos |
| 188 | 221.01 | scriber | item65.30 | 10 | Nos |
| 189 | 222.01 | punch, | item65.31 | 10 | Nos |
| 190 | 223.01 | v block angle plate | item65.32 | 5 | Nos |
| 191 | 224.01 | try square | item65.33 | 20 | Nos |
| 192 | 225.01 | hand reamer | item65.34 | 10 | Nos |
| 193 | 226.01 | machine reamer, | item65.35 | 10 | Nos |
| 194 | 227.01 | expanding reamer | item65.36 | 10 | Nos |
| 195 | 228.01 | Different sizes Hacksaw | item65.37 | 30 | Nos |
| 196 | 229.01 | Welding Shop Apron | item66.1 | 20 | Nos |
| 197 | 230.01 | Hand gloves | item66.2 | 20 | Nos |
| 198 | 231.01 | safety goggles | item66.3 | 20 | Nos |
| 199 | 232.01 | shoes | item66.4 | 10 | Nos |
| 200 | 233.01 | welding torch | item66.5 | 4 | Nos |
| 201 | 234.01 | pressure regulator | item66.6 | 2 | Nos |
| 202 | 235.01 | spark lighter | item66.7 | 20 | Nos |
| 203 | 236.01 | electrode for gas welding | item66.8 | 100 | Nos |
| 204 | 237.01 | electrode holder | item66.9 | 2 | Nos |
| 205 | 238.01 | cable lung | item66.10 | 10 | Nos |
| 206 | 239.01 | chipping hammer | item66.11 | 20 | Nos |
| 207 | 240.01 | earthing clamps | item66.12 | 10 | Nos |
| 208 | 241.01 | wire brush | item66.13 | 20 | Nos |
| 209 | 242.01 | Helmet | item66.14 | 20 | Nos |
| 210 | 243.01 | Sleeves | item66.15 | 5 | Nos |
| 211 | 244.01 | Arc Welding Machine with Trasformer,cables,Electrode holder,cables,connecter etc. | item66.16 | 1 | Nos |
| 212 | 245.01 | Gas Welding Machine.(oxyacctylene) with oxygen and acetelene cylinder ,pipes,welding torch etc. | item66.17 | 1 | Nos |
| 213 | 246.01 | Plastic moulding shop Bench moulding machine | item67 | 1 | Nos |
AI Tender Summary
Tender Timeline
Nov 26, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedDec 05, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 07, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender